FCC ID: 2A4DH-8726 Wireless Remote

Quick start guide This product is a Bluetooth Low Energy technology enabled Remote Control for use Model: K7Q3MT with a paired Media Player. WHATS IN THE BOX Marketing Name: Wireless Remote, Model K7Q3MT 2xAAA Batteries Setting up the device

- Insert the batteries and install the compartment cover

- Pair the device with the host. Choose the applicable pairing instructions from options A or B below:

A. This is a replacement remote control:

1. Restart your Media Player / TV USB Stick by disconnection from and then reconnection to the AC power. After the TV home screen displays your new remote it is ready for pairing. 2. Press and hold the Home button on the new remote for at least 10 seconds. The new remote should automatically pair with your TV USB stick. You will see an on-screen message when it has successfully paired. B. This is an additional remote control:

1. On your new remote, press and hold the Home button for 120 seconds to enter discoverable mode. 2. You must use your existing remote for the following steps. a. Press the Home button. b. Navigate to the Settings location at the top of the Media Player TV screen. Select Controllers and Bluetooth Devices > TV Remotes > Add New Remote. The Media Player application will search for discoverable remotes and display them in a list. c. Select the new remote. You will see an on-screen message when it has been successfully paired. Use your Voice Search

- Hold down voice search button and speak

Product Information User Manual Safety and Compliance Information Using Your Device Around Other Electronic Devices The Device, uses, and can radiate radio frequency (RF) energy and, if not used in accordance with its instructions, may cause interference to radio communications and electronic equipment. External RF signals may affect improperly installed or inadequately shielded electronic operating systems, entertainment systems, and personal medical devices. While most modern electronic equipment is shielded from external RF signals, if in doubt, check with the manufacturer. For personal medical devices (such as pacemakers and hearing aids), consult with your physician or the manufacturer to determine if they are adequately shielded from external RF signals. There are some places where RF signals could constitute a hazard, such as health care facilities, and construction sites. If you are not sure, look around for signs indicating that two-way radios or mobile phones should be turned off. FCC Compliance Information Radio Frequency Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications that are not expressly approved by the party responsible for compliance could make the device no longer comply with the FCC Rules. Information on your device is on file with the FCC and can be found by inputting your devices FCC ID, which can be found on the back of Device, into the FCC ID Search form available at transition.fcc.gov/oet/ea/fccid. The party responsible for FCC compliance is Amazon.com Services, Inc. 410 Terry Ave. North, Seattle WA 98109 USA. Website link: www.amazon.com/devicesupport Information Regarding Exposure to Radio Frequency Energy Your Device is designed and manufactured not to exceed the emission limits for exposure to RF energy set by the Federal Communications Commission of the United States (FCC). Information on your Device is on file with the FCC and can be found by inputting your Devices FCC ID (which can be found on the back of your Device) into the FCC ID Search form available at transition.fcc.gov/oet/ea/fccid. The output power of the radio technology used in the Device is below the radio frequency exposure limits set by the FCC. IC Compliance Information Radio Frequency Information This device complies with Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement."

The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. Information Regarding Exposure to Radio Frequency Energy This equipment complies with IC RSS-102 RF exposure limits set forth for an uncontrolled environment. Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Radio Frequency Exposure Compliance Statement Cet appareil a t test et respecte les limites applicables pour l'exposition aux radiofrquences (RF). Le Dbit d'Absorption Spcifique (DAS) local quantifie l'exposition de l'utilisateur aux ondes lectromagntiques de l'quipement concern. Le DAS maximum autoris est de 2 W / kg pour la tte et le tronc et de 4 W / kg pour les membres. CAN ICES-3(B)/NMB-3(B) Product Specifications Model Number: K7Q3MT Port: N/A Power: 3 x AAA Batteries Operating temperature: 0C to 35C Connectivity: BLE

CC OTH 00593373 2022 TR Date: September 9, 2022 To the Certification Body, Amazon.com Services LLC hereby authorizes Sporton International Inc., located at No.52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan, R.O.C., to provide and prepare all documentation relating to our product certification, including the signing of application forms for Model Name K7Q3MT (Product), FCC ID: 2A4DH-8726, directly to the Certification Body on our behalf. Sporton International Inc. is also authorized under this letter to respond on our behalf directly to the Certification Bodys questions about the Product and Reports as necessary to assist the Certification Body in the FCC certification. We further certify that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the Amazon.com Services LLC. Sincerely, Amazon.com Services LLC _____________________ Name: Amit Gaikwad Address: 410 Terry Avenue North, Seattle, Washington 98109, United States Telephone: 650-694-8333 Email: device-certification@amazon.com

CC OTH 00593383 2022 TR Amazon.com Services LLC 410 Terry Avenue North, Seattle, Washington 98109, United States Tel: 650-694-8333 Date: September 9, 2022 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for Confidentiality FCC ID: 2A4DH-8726 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Part List Operational Description Tune up procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFT 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, ______________________________ Amit Gaikwad Email: device-certification@amazon.com