FCC ID: 2AY2P-DA11ABL 2 inputs by 2 outputs Analogue and Bluetooth to Dante Converter

DA11ABL-WP-EU_REVA7_QRG_PrintReady.pdf 1 22/02/2023 09:51 DA11ABL-WP-EU QUICK REFERENCE GUIDE DA11ABL-WP-EU Quick Reference Guide C M Y CM MY CY CMY K Introduction The DA11ABL-WP-EU is a multi-input / output wall plate to convert Bluetooth and analogue audio within a digital Dante networked audio system. The DA11ABL-WP-

EU converts 2 x input channels of Bluetooth, or unbalanced audio to Dante digital audio, and 2 x channels of Dante audio to 2 x output channels of unbalanced audio. The DA11ABL-WP-EU is a plug & play device that is powered using PoE (Power over Ethernet), or via 12V power supply, offers support for AES67 RTP audio transport, and magnetic faceplate design allows for both UK & EU backbox compatibility. The DA11ABL-WP-EU is the ideal BYOD interface to allow any Bluetooth device to stream audio wirelessly to a Dante audio system. FEATURES:

Dante network wall plate interface for Bluetooth and analogue L/R audio inputs, and L/R audio outputs Converts 2ch Bluetooth, or un-balanced audio sources to Dante audio Converts 2x Dante audio channels to un-balanced audio outputs Adjustable input sensitivity from +24dBu to -28dBV via control software Adjustable output gain from +20dBu to -28 dBV via control software Supports: 44.1, 48 & 96kHz sample rates @ 16, 24 or 32 Bit Configurable Dante device latency (supports 1, 2 or 5ms configurable using Dante Controller) Supports AES67 RTP audio transport Features Class 0 IEEE 802.3af PoE for powering of product from any PoE switch Supports power via 12V DC adapter (supplied) for when network switch does not support PoE Magnetic faceplate surround allowing for both UK & EU backbox compatibility Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk 01 DA11ABL-WP-EU_REVA7_QRG_PrintReady.pdf 2 22/02/2023 09:51 Front Panel Connections:

1 Power Status Indicator - Illuminates when the devices is powered on power input 2 Bluetooth Status Indicator - Illuminates when Bluetooth device is connected 3 ID LED Indicator - Flashes when this device is identified through Dante Configurator 4 4 Analogue Audio Input - 3.5mm stereo jack for unbalanced analogue audio input 5 Bluetooth Pair Button - Press to make device discoverable for Bluetooth pairing, press 2 to 3 times to change audio source selection 6 Micro USB Port - Used for software control and firmware updates 7 Analogue Audio Output - RCA L / R connector unbalanced analogue audio output Rear Panel Connections:

1 Dante Network Connection (PoE) - RJ45 connection to connect to network switch 2 Power Port Use 12V/1A DC adaptor (not included) when PoE is not available to power device DA11ABL-WP-EU QUICK REFERENCE GUIDE 1 2 3 5 6 7 C M Y CM MY CY CMY K 1 2 Bluetooth Bluetooth 5.0 technology allows for 2x simultaneous connections from source audio devices, where the selected devices audio is received and sent into the Dante network. To connect a Bluetooth enabled device to the DA11ABL-WP-EU, press the Pair button on there unit, go to the Bluetooth settings of the source audio device, and enable Bluetooth connectivity. The DA11ABL-WP-EU will appear in the list of available devices. 02 www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk DA11ABL-WP-EU_REVA7_QRG_PrintReady.pdf 3 22/02/2023 09:51 DA11ABL-WP-EU QUICK REFERENCE GUIDE C M Y CM MY CY CMY K Dante Controller Dante Controller software is required in order to set up and configure the DA11ABL-WP-EU as well as control the Dante network. Audinate provide extensive training videos and documentation on their website. This can be found here: http://www.audinate.com/products/

software/dante-controller Upon connecting your DA11ABL-WP-EU to a compatible network, the Dante Controller software should automatically discover the device. The DA11ABL-WP-

EU will appear in the Dante Controller with a name prefixed with DA11ABL-WP-EU. On the Routing screen you can create audio routing between Dante transmitters and receivers in the system. Please ensure your PC is on the same network as your Dante devices. Dante is not able to transmit over WiFi, and it is recommended to hardwire into the Dante network. Having multiple network devices enabled can also confuse the Dante Controller software so it is recommended to disable WiFi during configuration. Advanced Dante Settings By default the DA11ABL-WP-EU is shipped with its network settings set to obtain an IP address automatically. This means that if a DHCP server is present on your network, it will provide the DA11ABL-

WP-EU with an IP address. If no DHCP server is present then the DA11ABL-WP-EU will receive a default IP address in the 169.254.xxx.xxx range. To change the IP address of the DA11ABL-WP-EU, you must enter the Network Config menu in the Device Info screen of the Dante Controller software. It is also possible to change the settings of the DA11ABL-WP-EU under the Device Info screen in the Dante Controller software. To do so, select the Device Config menu. The sample rate of the DA11ABL-WP-EU can be adjusted here. Please note: Dante products can only transmit or receive audio from other Dante products that are set up with the same sample rate. A mismatch in sample rate may stop audio from transmitting. Under the Device Config screen we can also adjust the latency of the DA11ABL-WP-EU from 1, 2 or 5 milliseconds. Contact: support@blustream.com.au | support@blustream-us.com | support@blustream.co.uk 03 RevA7_QRG_DA11ABL-WP-EU DA11ABL-WP-EU_REVA7_QRG_PrintReady.pdf 4 22/02/2023 09:51 Specifications Audio Input Connectors: 1 x Analogue Left / Right audio (3.5mm stereo jack) Audio Output Connectors: 2 x Analogue RCA (Left / Right) Network Connectors: 1 x PoE Dante Ethernet Connection (RJ45) Bluetooth: Bluetooth V5.0 - SBC / MP3 / AAC / APT-X / APTX-LL / APTX-HD, 44.1K-48KHz 16 / 24Bit Configuration Switches: 1 x Push button (connect / selection) Firmware Upgrade: 1 x Micro-USB UART port Module Dimensions (W x H x D): 74mm x 74mm x 50mm (without faceplate) Faceplate Dimensions (W x H x D): 85mm x 85mm x 5mm Cut Out Dimensions (W x H x D): 52mm x 55mm x 38mm Mounting Hole Spacing: UK 60mm CTC, EU 60mm CTC Backbox Requirements: UK single gang backbox / EU single gang backbox Shipping Weight: 0.3kg Operating Temperature: 32F to 104F (0C to 40C) Storage Temperature: - 4F to 140F (- 20C to 60C) Power Supply: Class 1 IEEE 802.3af POE PD or 12V/1A DC, 2-Pin Phoenix connector DA11ABL-WP-EU QUICK REFERENCE GUIDE Package Contents 1 x DA11ABL-WP-EU 1 x Magnetic Faceplate 1 x Quick Reference Guide Acknowledgements Dante is a registered trademark of Audinate Pty Ltd. Certifications FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION - changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. CANADA, INDUSTRY CANADA (IC) NOTICES This Class B digital apparatus complies with Canadian ICES-003.Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CORRECT DISPOSAL OF THIS PRODUCT This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling. RF EXPOSURE To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. CANADA, INDUSTRY CANADA (IC) NOTICES This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

Lappareil ne doit pas produire de brouillage;

Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. 04 www.blustream.com.au | www.blustream-us.com | www.blustream.co.uk C M Y CM MY CY CMY K

REVA6_DA11ABL-WP-EU_Silkscreen_Sticker_PrintReady.pdf 1 20/09/2022 17:05 C M Y CM MY CY CMY K HDP-WPD22BEU-AU0888- -TEM 20221213 48*32mm DA11ABL-WP-US_Sticker_PrintReady.pdf 1 19/08/2022 11:43 C M Y CM MY CY CMY K I C

2 7 0 2 1

D A 1 1 A B L W P E U HDP-WPD22BUS-AU0888- -TEM 20221213 DA11ABL-WP-US_Sticker_PrintReady.pdf 1 19/08/2022 11:43 C M Y CM MY CY CMY K I C

2 7 0 2 1

D A 1 1 A B L W P E U HDP-WPD22BUS-AU0888- -TEM 20230223 label location

(Blustream PTY LTD) Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 02-23-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AY2P-DA11ABL

[Blustream PTY LTD] (the applicant) certifies that the equipment for which authorization is sought is notcovered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely,

(Applicantsignature) Martyn Shirley

(Applicant printed name) Martyn Shirley Rev 1/26/2023

(Blustream PTY LTD) Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 02-23-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AY2P-DA11ABL

[Blustream PTY LTD] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely,

(Applicant signature) Martyn Shirley

(Applicant printed name) Martyn Shirley Rev 1/26/2023

(Blustream Pty Ltd) Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AY2P-DA11ABL Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type

(ie- Block Diagram, Schematics, Operational Description, Parts List, Tune Up Info) Schematic Diagram Block Diagram Operational Description File Name

(ie- 1100_schematics.pdf) Schematic Diagram Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

requests short-term Confidentiality of following sections of this application for a period of 180 days after grant is issued. Exhibit Type

(ie- External Photos, Internal Photos, Test Setup Photos, Manual) External Photos Test Setup Photos Internal Photos User Manual File Name

(ie- 1100_external photos.pdf) External Photos Test Setup Photos Internal Photos User Manual Sincerely,

(signature) Martyn Shirley

(printed name): Martyn Shirley Date: 1/12/2023 Rev 11/20/07

Blustream Pty Ltd 26 Lionel Rd, Mount Waverley, Melbourne, Victoria 3149, Australia Date: 1/12/2023 FCC ID: 2AY2P-DA11ABL Model Number: DA11ABL-WP-EU,DA11ABL-WP-US,DA11ABL-WP To:

Federal Communication Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21048 To Whom It May Concern, We, Blustream Pty Ltd declare that this EUT (FCC ID: 2AY2P-DA11ABL) will conduct FCC compliance testing, the sDOC part recognized test lab(Shenzhen NTEK Testing Technology Co., Ltd.). 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street Baoan District, Shenzhen 518126 P.R. China Please contact me if you have any question. Sincerely, Blustream Pty Ltd 26 Lionel Rd, Mount Waverley, Melbourne, Victoria 3149, Australia

(Signed) Martyn Shirley Name: Martyn Shirley Phone: +61 3 8691 1999 Fax: +61 3 8691 1999 Email: support@blustream.com.au

Blustream Pty Ltd Family models declaration letter. 1/12/2023 We Company: Blustream Pty Ltd Address: 26 Lionel Rd, Mount Waverley, Melbourne, Victoria 3149, Australia Product: 2 inputs by 2 outputs Analogue and Bluetooth to Dante Converter Model Name: DA11ABL-WP-EU Family Model: DA11ABL-WP-US,DA11ABL-WP All models are the same circuit and RF module, except the model name. Thanks Sincerely, Signature Martyn Shirley

[Name] Martyn Shirley

[Title] General Manager Blustream Pty Ltd

(Blustream Pty Ltd) Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 1/12/2023 SUBJECT: FCC Application for FCC ID: 2AY2P-DA11ABL To Whom It May Concern:

We, the undersigned, hereby authorize Alex Li at Shenzhen NTEK Testing Technology Co., Ltd. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Shenzhen NTEK Testing Technology Co., Ltd. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards,

(signature) Martyn Shirley

(printed name): Martyn Shirley M:\Master Documents\TEMPLATES\POA_Letter.doc

THREE STONES MEDIA LLC U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: 02-23-2023 Ref: Attestation Statement Part2.911(d)(7) filing FCC ID: 2AY2P-DA11ABL Blustream PTY LTD (the applicant) certifies that, as of the date of the filing of the application, THREE STONES MEDIA LLC(the agent) is our designated U.S. agent for service of process for the abovereference FCC ID. The applicant accepts to maintain an agent for service of process in the United States forno less than one year after either the grantee has permanently terminated all marketing and importation of theapplicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicialproceeding involving the equipment, whichever is later. The applicant further acknowledges it is ourresponsibility to inform the FCC whenever the agent information changes. THREE STONES MEDIA LLC ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name:

THREE STONES MEDIA LLC FRN: 0033401761 GC: 2A99E Address:

1200 Broadway St. APT 329, Los Angeles, CA90015 Contact Person: Sijie Zhang Signature:

Tel: +1 267 909 3692 Email: abbyzhangmedia@gmail.com Applicant Company Name:

Blustream PTY LTD Address:

26 Lionel Rd, Mount Waverley, Melbourne, Victoria 3149, Australia Contact Person: Martyn Shirley Signature:

Martyn Shirley Tel: +61 3 8691 1999 Email: support@blustream.com.au