FCC ID: PIY-FYK60-20-A5T Counting Koala

Spin for fun sounds, phrases, music, and songs introducing shapes, animals, numbers, and colors!

Press the buttons for numbers and counting fun. Keep this instruction sheet for future reference, as it contains important information. FYK60 Batteries And Power 1,5V x 3 AA (LR6) Requires three AA (LR6) alkaline batteries

(included). Batteries included are for demonstration purposes only. For longer life, use alkaline batteries. Battery Safety Information In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:

Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable. Insert batteries as indicated inside the battery compartment (+ and -). Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries inside may explode or leak. Never short-circuit the battery terminals. Use only batteries of the same or equivalent type, as recommended. Do not charge non-rechargeable batteries. Remove rechargeable batteries from the product before charging. If removable, rechargeable batteries are used, they are only to be charged under adult supervision. Protect the environment by not disposing of this product or any batteries with household waste. This symbol indicates that this product shall not be treated as household waste. Check your local authority for recycling advice and facilities. To clean, wipe with a damp cloth. Do not immerse. Loosen the screw in the battery compartment door and remove the door. Remove the exhausted batteries and properly dispose. Insert three, new AA (LR6) alkaline batteries. Replace the battery compartment door and tighten the screw. Slide the power-volume switch to ON with low volume, ON with high volume or OFF. When sounds or lights become faint or stop, its time for an adult to change the batteries. If this toy begins to operate erratically, you may need to reset the electronics. Slide the power-volume switch off and then back on again. More fun with more than one!

Each sold separately and subject to availability. Heres how to sync your Linkimals!

1 Turn power OFF on each toy. 2 Now turn power ON. 3 Watch and listen to Linkimals respond to each other in fun ways during play!

Uh-oh! If, at any time, one of your Linkimals doesnt seem to be interacting with the other Linkimals, turn all of them OFF and then back ON again. Linkimals are also available in different languages (sold separately and subject to availability). Linkimals only sync with other Linkimals of the same language. UNITED STATES Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052. Consumer Services:

1-800-432-5437. CANADA Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2 Consumer Services: 1-800-432-5437. www.service.mattel.com. GREAT BRITAIN Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303. www.service.mattel.com/uk. NEDERLAND Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland. AUSTRALIA Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1300 135 312. NEW ZEALAND 16-18 William Pickering Drive, Albany 1331, Auckland. SOUTH AFRICA Mattel South Africa (PTY) LTD, Office 102 I3, 30 Melrose Boulevard, Johannesburg 2196. FCC STATEMENT (UNITED STATES ONLY) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment Consult the dealer or an experienced radio/TV and receiver. technician for help. NOTE: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) Lappareil ne doit pas produire de brouillage;

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement 2019 Matt el. PRINTED IN CHINA FYK60-0970-1102057572-DOM

co This device complies with Part 15 of the FCC Rules. ration is subject tothe folowing two conditions:

This device may not cause harmful Interference, and (2) this device must accept any interference received, including Interference that may cause undesired operation. CAN ICES-3 (BYNMB-3 (B)

To:

Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 Regarding: Confidentiality Request regarding application for FCC ID: PIY-FYK60-20-A5T LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential for 90 days from the grant date. If the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Joule Mak On behalf of Company: Mattel Asia Pacific Sourcing Ltd. Telephone: 31855000 E-mail: Joule.Mak@mattel.com Signature:

Title: Director, Electronic Engineering

TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: PIY-FYK60-20-A5T To whom it may concern:

Date: 2019/12/13 We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Jing Song in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Mattel Asia Pacific Sourcing Ltd. This authorization is valid until further written notice from the applicant. Print Name: Joule Mak Title: Director, Electronic Engineering On behalf of Company: Mattel Asia Pacific Sourcing Ltd. Telephone: 31855000 E-mail: Joule.Mak@mattel.com Signature: