FCC ID: PIYHGV87-22A5T HOT WHEELS Monster Trucks HWMT UNSTOPPABLE TIGER SHARK RC Vehicle

HGV87-0970_I/S_DOM Size: 16.5 x 12 1: CONTENTS 4+

TM HW UNSTOPPABLE TIGER SHARK 2: FEATURES DRIVING CONTROLS LED INDICATOR STOMP BUTTON BATTERY BOX STEERING ALIGNMENT 3: SET UP (CONTD.) B. CHARGING THE VEHICLE The vehicle is powered by a permanently installed Lithium-ion (Li-ion) battery, and it must be fully charged before rst use. 1. Slide the power switch to CHARGE ( ) . 2. Open the charge port cover. 3. Connect one end of the charge cord to the vehicle's charge port and plug the other end in to a 5V/1000 mAH USB charger (not included). 4. Charging will begin when the cord is connected. A red LED on the vehicle will light up as the vehicle is charging. 5. The red LED will turn green when the vehicle is fully charged. Unplug the charge cord when charging is complete. A full charge will usually take approximately 90 minutes. Charging time may vary. 6. Close the charge port cover. 7. Recharge the vehicle if the vehicle begins to run slowly or does not respond. NOTE: Power switch must be in the CHARGE ( ) position when charging the vehicle. Red Vehicle is charging Green Vehicle is fully charged HVIN: HGV87R ( ), HGV87T ( ) CAUTION:

Surfaces may become hot and cause burns if electronics get wet. To prevent entanglement, keep all hair away from moving parts. Adult supervision is recommended when the vehicle is being operated. Keep these instructions for future reference as they contain important information. IMPORTANT: Please read all instructions before operating your vehicle. The toy is only to be connected to Class II equipment bearing the symbol . CHARGE PORT COVER CHARGE PORT 3: SET UP A. REMOTE CONTROLLER BATTERY INSTALLATION 1. Unscrew the battery cover with a Phillips head screwdriver (not included). 2. Install 2 AA (LR6) 1.5V alkaline batteries (not included) with polarity (+/-) as shown inside the battery compartment. For longer life, use alkaline batteries. 3. Replace battery cover and tighten screw. 4. Replace batteries in the remote controller if the LED on the remote controller does not go on during play or if the vehicle does not respond well after a recharge. BOTTOM VIEW TIP: The battery will be hot after play. Wait at least 10 to 15 minutes until the battery cools down before recharging the vehicle. POWER SWITCH I O

= ON

= OFF

= CHARGE LED INDICATOR C. PAIRING THE REMOTE CONTROLLER AND VEHICLE 1. Slide the power switch to ON (I) on the vehicle. 2. Press the stomp button or push the remote controller's driving control joystick forward/backward after switching on the vehicle. 3. Pairing is complete when the LED changes from ashing red to solid red on Pairing remote controller. NOTE: If the vehicle does not respond to the remote controller after pairing, switch the vehicle o then back on to try pairing again or replace the batteries in the remote controller if the batteries are drained. Pairing is complete 1 2 OR TIP: The vehicle will go into sleep mode if left idle for approximately 15 minutes to preserve battery life. To resume normal play, slide the vehicle's power switch to OFF then ON again, and then push the remote controller's driving control joystick forward/backward to pair the vehicle and remote controller. D. STEERING ALIGNMENT 1. Check the vehicle's steering alignment before playing by driving it forward to see if it is driving straight. 2. If the vehicle automatically steers toward the right/left, press the alignment button in the opposite direction a few times until it runs in a straight line. 2022 Mattel. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Services 1-800-524-8697. Mattel U.K. Limited, The Porter Building, 1 Brunel Way, Slough SL1 1FQ, UK. Mattel Australia Pty. Ltd., 658 Church St., Richmond, Victoria, 3121. Consumer Advisory Service - 1300 135 312. Mattel South Africa (PTY) LTD, Ofce 102 I3, 30 Melrose Boulevard, Johannesburg 2196. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Tel.: (852) 3185-6500. Diimport & Diedarkan Oleh: Mattel Continental Asia Sdn Bhd. Level 19, Tower 3, Avenue 7, No. 8 Jalan Kerinchi, Bangsar South, 59200 Kuala Lumpur, Malaysia. HGV87-0970_DOM 1 x2 AA (LR6) 1.5V ALIGNMENT BUTTONS 2 3 4: HOW TO DRIVE CHECKLIST Is the vehicle fully charged?

Is the remote controller equipped with fresh batteries?

Is the remote controller paired with the vehicle?

Has the vehicle's steering been aligned?

CONTROLS Wheelie!

1. Drive forward and backward in full speed to build momentum. 1a 1b 5: CONSUMER INFORMATION TIPS & HINTS FOR ALL DRIVING ENVIRONMENTS FORWARD/BACKWARD LEFT/RIGHT STEERING 2. As the vehicle is going backwards, quickly push 3. Drive forward to keep the wheelie going!

the driving control all the way up to do a wheelie!

2 3 SKILL CHECK!

Remember, steering directions are ipped on the remote controller when you are driving backward!

NOTE: Operating range of the remote controller is up to 30 m (98 ft). a b 1. When your vehicle starts to lose power, it may lose functionality or performance. It's time for a recharge. For best performance, always start with a fully-charged battery. Your vehicle's running time may change depending on driving style and driving environment. 2. Radio interference can make your vehicle run poorly. Interference can be caused by other RC vehicles running on the same frequency, electrical wires, large buildings, CB radios, or other wireless gear. Try to stay away from these!

3. Point your remote controller up, and not down toward your vehicle. If your vehicle gets too far away, it won't work properly. 4. Dont store your vehicle near heat or in direct sunlight. Always turn switches OFF and remove all batteries from remote controller before storage. 5. Don't drive your vehicle in sand or through water or snow. Do not immerse in water. If your vehicle does get wet, wipe it with a towel and allow to dry completely overnight. If your remote controller is accidentally dropped in water, remove battery(ies) and allow your remote controller to air dry. Replace with fresh battery(ies) before operation. 6. When exposed to an electrostatic source, the remote controller and/or the vehicle may malfunction. To resume normal operation of the remote controller, remove the batteries and reinstall them after 5 seconds. To resume normal operation of the vehicle, turn the power OFF for 5 seconds, then turn it ON again. SAFETY TIPS Play safely! Do not drive the vehicle in the street!

DO NOT pick up the vehicle while in motion. Keep ngers, hair, and loose clothing away from the wheels while the vehicle is switched ON. Adult supervision is recommended when this vehicle is being operated. To avoid accidental operation, remove all batteries from the remote controller when not in use and switch the vehicle OFF before storage. STUNTS Stomp!

Chomp!

Wheelie Spin!

RECHARGEABLE BATTERY SAFETY INFORMATION Rechargeable batteries are only to be charged under adult supervision. Do not recharge battery if it is hot. Allow it to cool before recharging. Do not recharge a battery pack that shows leakage or corrosion. Do not disassemble the battery pack. The battery pack is a sealed rechargeable Li-ion battery pack. If the battery pack and/or charging port are wet, thoroughly dry before charging. Do not recharge non-rechargeable batteries. The Li-ion battery in the vehicle is not intended to be replaced or removed by consumers. Before disposal in the waste stream, the Li-ion battery must be removed by a qualied professional and disposed of separately according to local regulations on battery collection and recycling. Do not dispose of the batteries in a re. BATTERY SAFETY INFORMATION In exceptional circumstances, batteries may leak uids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:

Non-rechargeable batteries are not to be recharged. Rechargeable batteries are to be removed from the product before being charged. Rechargeable batteries are only to be charged under adult supervision. Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries. Do not mix old and new batteries. Only batteries of the same or equivalent type as recommended are to be used. Batteries are to be inserted with the correct polarity (+ and ). Exhausted batteries are to be removed from the product. The supply terminals are not to be short-circuited. Dispose of battery(ies) safely. Do not dispose of this product in a re. The batteries inside may explode or leak. Protect the environment by not disposing of this product or any batteries with household waste. This symbol indicates that this product shall not be treated as household waste. Check your local authority for recycling advice and facilities. OR FOR PRODUCT SOLD IN USA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. NOTE: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the users authority to operate the equipment. 4 5 6

Mattel Asia Pacific Sourcing Ltd. TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding:

Confidentiality Request regarding application for FCC ID: PIYHGV87-22A5T LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within confidential period, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. Schematic(s) Block Diagrams Operational Descriptions External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Signature:

Print Name: Joule Mak Title: Director, Electronic Engineering On behalf of Company: Mattel Asia Pacific Sourcing Ltd. Telephone: 31855000 E-mail: Joule.Mak@mattel.com

a) b) c) d) e) f) g) SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration 13/F., South Tower, World Finance Centre, Harbour City, Tsimshatsui,Kowloon 852, Hong Kong Applicant Legal Business Name Mattel Asia Pacific Sourcing Ltd. Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name Joule Mak PIY PIYHGV87-22A5T Joule.Mak@mattel.com 31855000 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date: 04/11/2022 Print Name:

Title:

Joule Mak Director, Electronic Engineering

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

Mattel Asia Pacific Sourcing Ltd. Date: 04/07/2022 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: PIYHGV87-22A5T To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou Branch and Kobe Jian in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Mattel Asia Pacific Sourcing Ltd. This authorization is valid until further written notice from the applicant. Print Name: Joule Mak Signature:

On behalf of Company: Mattel Asia Pacific Sourcing Ltd. Telephone: 31855000 E-mail: Joule.Mak@mattel.com Title: Director, Electronic Engineering