FCC ID: PIYGYD26-21A5T HOT WHEELS RC Aaron Wheelz Wheelie Chair

GYD26-0970-G1_DOM_I/S Size: 11 x 18 Front G1: Updated the images per engineers comment. 1: CONTENTS AARON WHEELZ WHEELIE CHAIR 2: FEATURES BACK VIEW ON/OFF SWITCH 3: SET UP INSTRUCTIONS X TM Back CONTROLS FORWARD/BACKWARD BOOST 6+

TIP:

Tilt the wheelie chair back and try pulling off different tricks with the driving controls!

LEFT/RIGHT STEERING Keep these instructions for future reference as they contain important information. IMPORTANT: Please read all instructions before operating your wheelie chair. CAUTION:

Surfaces may become hot and cause burns if electronics get wet. To prevent entanglement, keep all hair away from moving parts. Adult supervision is recommended when the wheelie chair is being operated The wheelchair and helmet logo is a registered trademark of WCMX International LLC. 2021 Mattel. and designate U.S. trademarks of Mattel, except as noted. Mattel, Inc., 636 Girard Avenue, East Aurora, NY 14052, U.S.A. Consumer Services 1-800-524-8697. Mattel U.K. Limited, The Porter Building, 1 Brunel Way, Slough SL1 1FQ, UK. Mattel Australia Pty. Ltd., 658 Church St., Richmond, Victoria, 3121. Consumer Advisory Service - 1300 135 312. Mattel South Africa (PTY) LTD, Ofce 102 I3, 30 Melrose Boulevard, Johannesburg 2196. Mattel East Asia Ltd., Room 503-09, North Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. Tel.: (852) 3185-6500. Diimport & Diedarkan Oleh: Mattel Continental Asia Sdn Bhd. Level 19, Tower 3, Avenue 7, No. 8 Jalan Kerinchi, Bangsar South, 59200 Kuala Lumpur, Malaysia. SPEED BOOST Press the FORWARD + BOOST buttons, for extra speed off the ramp!

GYD26-0970-G1-DOM NOTE:

Operating range of the remote controller is up to 25 m (82 ft). The wheelie chair and remote controller will go into sleep mode if left idle for approximately 5 minutes. To resume normal play, press and hold the remote controllers pairing button until the LED lights up again. CHARGE CORD USB Charger not included. REMOTE CONTROLLER STICKER SHEET Colors and decorations may vary. CARDBOARD RAMP STUNT RECOVERY 360 SPINS Fall down, toggle the DIRECTIONAL CONTROLS to get up and keep stunting!

Press the BOOST button for wild 360 spins!

LED INDICATOR BOOST BUTTON DRIVING CONTROLS PAIRING BUTTON CONSUMER INFORMATION ALIGNMENT BUTTONS TIPS & HINTS FOR ALL DRIVING ENVIRONMENTS CHARGE PORT LED INDICATOR A. REMOTE CONTROLLER BATTERY INSTALLATION 1. Unscrew the battery cover with a Phillips head screwdriver (not included). 2. Install 2 AA (LR6) 1.5V alkaline batteries (not included) with polarity (+/-) as shown inside the battery compartment. For longer life, use alkaline batteries. 3. Replace battery cover and tighten screw. 4. Replace batteries in the remote controller if the wheelie chair does not respond well after a recharge. B. CHARGING THE WHEELIE CHAIR The wheelie chair is powered by a permanently installed Lithium-ion (Li-ion) battery, and it must be fully charged before rst use. 1. Switch off the wheelie chair by sliding the power switch to OFF (O). 2. Connect one end of the charge cord to the wheelie chairs charge port and plug the other end in to a 5V/1000 mAH USB charger (not included). 3. A red LED will light up on wheelie chair as it is charging. 4. The red LED will turn green when the wheelie chairs battery is fully charged. A full charge will take approximately 60 minutes (charging time may vary). Unplug the cord when charging is complete. 5. Recharge the wheelie chair if its LED rapidly ashes then goes off or if the wheelie chair begins to respond slowly. Low battery Red Wheelie chair is charging Green Wheelie chair is fully charged TIPS:

Power switch must be in the OFF (O) position when charging the wheelie chair. Charging the battery for more than what is recommended will not give you a longer running time. The battery will be hot after play. Wait at least 10 to 15 minutes until the battery cools down before recharging the wheelie chair. C. PAIRING THE REMOTE CONTROLLER AND WHEELIE CHAIR 1. Slide the power switch to ON (I) on the wheelie chair. 2. Press the pairing button on the remote controller after switching on the wheelie chair. 3. Pairing is complete when the LED changes from ashing red to solid red on the remote controller. Pairing Pairing is complete NOTE: If the LED indicator does not stop ashing in approximately 10 seconds, switch off the wheelie chair, turn it back on, and then press the pairing button on the remote controller to try pairing again. ALIGNMENT BUTTONS D. STEERING ALIGNMENT 1. Check the wheelie chair's steering alignment before playing by driving it forward to see if it is driving straight. 2. If the wheelie chair automatically steers toward the right/left, press the alignment button in the opposite direction a few times until it runs in a straight line. 4: HOW TO DRIVE CHECKLIST Is the wheelie chair fully charged?

Is the remote controller equipped with fresh batteries?

Is the remote controller paired with the wheelie chair?

Has the wheelie chairs steering been aligned?

1) When your wheelie chair starts to lose power, it may lose functionality or performance. It's time for a recharge. For the best performance, always start with a fully-charged battery. Your wheelie chair's running time may change depending on driving style and driving environment. 2) Radio interference can make your wheelie chair run badly. Interference can be caused by other RC vehicles running on the same frequency, electrical wires, large buildings, CB radios, or other wireless gear. Try to stay away from these!

3) Point your remote controller up, and not down toward your wheelie chair. If your wheelie chair gets too far away, it won't work properly. 4) Dont store your wheelie chair near heat or in direct sunlight. Always turn switches OFF and remove all batteries from remote controller before storage. 5) Don't drive your wheelie chair in sand or through water or snow. Do not immerse your wheelie chair in water. If your wheelie chair does get wet, wipe it with a towel and allow to dry completely overnight. If your remote controller is accidentally dropped in water, remove battery(ies) and allow your remote controller to air-dry. Replace with fresh battery(ies) before operation. 6) When exposed to an electrostatic source, the remote controller and/or the wheelie chair may malfunction. To resume normal operation of the remote controller, remove the batteries and reinstall them after 5 seconds. To resume normal operation of the wheelie chair, turn the power OFF for 5 seconds, then turn it ON again. SAFETY TIPS x2 AA (LR6) 1.5V 1. Play safely! Do not drive the wheelie chair in the street!

2. DO NOT pick up the wheelie chair while in motion. 3. Keep ngers, hair, and loose clothing away from the wheels while the wheelie chair is switched ON. 4. Adult supervision is recommended when the wheelie chair is being operated. 5. To avoid accidental operation, remove all batteries from the remote controller when not in use and switch the wheelie chair OFF before storage. RECHARGEABLE BATTERY SAFETY INFORMATION 1. Rechargeable batteries are only to be charged under adult supervision. 2. Do not recharge battery if it is hot. Allow it to cool before recharging. 3. Do not recharge a battery pack that shows leakage or corrosion. 4. Do not disassemble the battery pack. The battery pack is a sealed rechargeable Li-ion battery pack. 5. If the battery pack and/or charging port are wet, thoroughly dry before charging. 6. Do not recharge non-rechargeable batteries. 7. The Li-ion battery in the wheelie chair is not intended to be replaced or removed by consumers. Before disposal in the waste stream, the Li-ion battery must be removed by a qualied professional and disposed of separately according to local regulations on battery collection and recycling. 8. Do not dispose of the batteries in a re. BATTERY SAFETY INFORMATION In exceptional circumstances, batteries may leak uids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:

Non-rechargeable batteries are not to be recharged. Rechargeable batteries are to be removed from the product before being charged. Rechargeable batteries are only to be charged under adult supervision. Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries. Do not mix old and new batteries. Only batteries of the same or equivalent type as recommended are to be used. Batteries are to be inserted with the correct polarity (+ and ). Exhausted batteries are to be removed from the product. The supply terminals are not to be short-circuited. Dispose of battery(ies) safely. Do not dispose of this product in a re. The batteries inside may explode or leak. Protect the environment by not disposing of this product or any batteries with household waste. This symbol indicates that this product shall not be treated as household waste. Check your local authority for recycling advice and facilities. FOR PRODUCT SOLD IN USA POUR LES PRODUITS VENDUS AUX TATS-UNIS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. NOTE: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the users authority to operate the equipment. Cet appareil est conforme l'article 15 de la rglementation de la FCC. L'utilisation de ce dispositif est autorise seulement aux deux conditions suivantes :

(1) il ne doit pas produire de brouillage nuisible, et (2) l'utilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Cet appareil a t test et jug conforme aux limites de la classe B pour un appareil numrique en vertu de l'article 15 de la rglementation de la FCC. Ces limites ont t instaures pour fournir une protection raisonnable contre toute interfrence nuisible dans une installation rsidentielle. Cet appareil gnre, utilise et peut mettre de l'nergie radiofrquence. S'il n'est pas install et utilis conformment aux instructions, il peut provoquer des interfrences sur les communications radio. Cependant, il n'est pas garanti que des interfrences ne se produiront pas dans certaines installations. Si cet appareil cause des interfrences la rception radio ou tlvise (ce qui peut tre vri en teignant l'appareil puis en le remettant sous tension), l'utilisateur peut tenter de les rsoudre en suivant une ou plusieurs des mesures ci-aprs :

Rorienter ou dplacer l'antenne rceptrice. Augmenter l'espace entre l'appareil et le rcepteur. Brancher l'appareil sur une prise de courant dirente de celle sur laquelle le rcepteur est branch. Pour obtenir de l'aide, contacter le vendeur ou un technicien radio/tlvision expriment. REMARQUE : Tout changement ou modication de cet appareil n'ayant pas t expressment approuv par les parties responsables de sa conformit peut entraner l'annulation du droit d'exploitation de l'quipement par l'utilisateur. FOR PRODUCT SOLD IN CANADA POUR LES PRODUITS VENDUS AU CANADA This equipment complies with FCC & Canada radiation exposure limits set forth for uncontrolled environments. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet quipement est conforme aux limites dexposition aux radiations dnies par le Canada pour des environnements non contrls. Cet metteur ne doit pas tre install au mme endroit ni utilis avec une autre antenne ou un autre metteur. L'metteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR d'Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) L'appareil ne doit pas produire de brouillage; (2) L'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

GYD26 remote control This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference,and

(2)This device must accept any interference received, including interference that may cause undesired operation.

(VALID IN THE US AND CANADA ONLY) CAN ICES-3(B)/NMB-3(B) 2021 Mattel 1186 MJ,1,NL MADE IN VIETNAM GyD26 HVIN:GYD26T 2.4GHz FCC ID:PIYGYD26-21AST IC:4390C-GYD2621A5T V-3625C

+1.5V AAILRG - 30

-1.5V AA/LR6_+

Attes with Pert 18 of the FCC Rules, following two conditions:

rfl Interference, and y Interference received, Hoe that May cause whidestred operetion. ANDY CANADIAN ONLY) HVIN:GYD26T FCC ID:PIYGYD26-21A5T IC:4390C-GYD2621A5T V-3625C

Mattel Asia Pacific Sourcing Ltd DE acHec ya WA PLO Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: PIYGYD26-21A5T To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou Branch and Kobe Jian in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, { acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Mattel Asia Pacific Sourcing Ltd. This authorization is valid until further written notice from the applicant. Print Name: Joule Mak ; Title: Director, Electronic Engineering Taree On behalf of Company: Mattel Asia Pacific Sourcing Ltd Telephone: 31855000 E-mail: Joule: Mak@mattel.com

Mattel Asia Pacific Sourcing Ltd Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: PIYGYD26-21A5T /

LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within confidential period, the applicant will notify the TCB per FCC KDB 726920 DO1 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Saas eo1 NA Print Name: Joule Mak Title: Director, Electronic Engineering Byala) On behalf of Company: Mattel Asia Pacific Sourcing Ltd Telephone: 31855000 E-mail: Joule: Mak@mattel.com

SGS

: This declaration FCC database SGS8 North America Inc. r r]

620 Old Peachtree Road ed Declaration SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Mattel Asia Pacific Sourcing Ltd. Address 13/F., South Tower, World Finance Centre, Harbour City, Tsimshatsui,Kowloon 852, Hong boy its Grantee Code una FCC ID PIYGYD26-21A5T ~

Authorized Contact Name Joule Mak Contact Email Joule.Mak@mattel.com Contact Phone 31855000

|, the undersigned, certify that | am an authorized signatory for the Applicant and therefore declare;

a) b) 9) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

(1) labeling the equipment with the exact FCC ID as specified in this application,

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with |SO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing.

(2) the Applicant shail make provisions to always have a production sample available upon request by SGS, FCC and/or ISED.

(3) the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. ia acon Oa acy Link to KDBs: findex.cfm Link to RSP-100:

Applicant Signature: Date: 9/17/2021 ATeye Come Print Name Title

*NOTE Director, Electronic Engineering cannot be signed by an Agent, it shall be signed by an authorized person listed in the Applicant Declaration Rev:0.0