FCC ID: 2AR2STAUN102 Wireless Bluetooth in-ear headphones

TAUN102 User manual Register your product and get support at www.philips.com/support Contents 1 Important safety instructions Hearing Safety General information 2 Your Bluetooth in-ear headphones What's in the box Other devices Overview of your Bluetooth in-ear senohpdaeh 3 Get started Charge your headphones Pair the headphones with your mobile enohp 4 Use your headphones Connect the headphones to a Bluetooth device Manage your calls and music 5 Technical data 2 2 2 3 3 3 3 4 4 4 5 5 5 7 6 Notice 8 Notice of compliance 8 Disposal of your old product and battery 8 skramedarT 9 7 Frequently asked questions 10 EN 1 1 Important safety instructions General information To avoid damage or malfunction:

Caution Do not expose headphones to excessive heat Do not drop your headphones. Headphones shall not be exposed to dripping or splashing. Do not allow your headphones to be submerged in water. Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives. If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product. The integrated battery shall not be exposed to excessive heat such as sunshine, fire or the like. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. About operating and storage temperatures and humidity Operate or store in a place where temperature is between -15C (5F) and 55C (131 F) (up to 90% relative humidity. Battery life may be shorter in high or low temperature conditions. Hearing Safety Danger To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headset. Listen at reasonable volumes for reason-

able periods of time. Be careful not to adjust the volume continuously upwards as your hearing adapts. Do not turn up the volume so high that you can't hear what's around you. You should use caution or temporarily discontinue use in potentially hazardous situations. Excessive sound pressure from earphones and headphones can cause hearing loss. Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving. For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments. 2 EN Other devices A mobile phone or device (e.g. notebook, PDA, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headphones (see 'Technical data' on page 7). Overview of your Bluetooth in-ear headphones 2 Your Bluetooth in-ear headphones Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. With this Philips wireless in-ear headphones, you can:

enjoy convenient wireless handsfree calls;

enjoy and control wireless music;

switch between calls and music. What's in the box Philips Bluetooth in-ear headphones TAUN102 Next / Volume up MIC / LED indicator On/off, music/call control button Micro USB charging slot Previous/Volume down Earfins Caps( M / L) USB charging cable

(for charging only) Quick start guide EN 3 Make sure that the headphones are fully charged and turned off. Press and hold the on/off button, blue and red LED flashes alternately. Blue light flashes for successful pairing. The headphones remain in pairing mode for 5 minutes. Make sure that the mobile phone is turned on and its Bluetooth feature is activated. Pair the headphones with the mobile phone. For detailed information, refer to the user manual of your mobile phone. The following example shows you how to pair the headphones with your mobile phone. Activate the Bluetooth feature of your mobile phone, select Philips UN102. Enter the headset password "0000" (4 zeros) if prompted. For those mobile phones featuring Bluetooth 3.0 or higher, no need to enter a password. UN102 3 Get started Charge your headphones Note Before you use your headphones for the first time, charge the battery for 5 hours for optimum battery capacity and lifetime. Use only the original USB charging cable to avoid any damage. Finish your call before charging the headphones, as connecting the headphones for charging will power the headphones off. Connect the supplied USB charging cable to:

the micro USB charging slot on the headphones and;

the charger/USB port of a computer LED turns red during charging and turns blue when the headphones is fully charged. Tip Normally, a full charge takes 2 hours. Pair the headphones with your mobile phone Before you use the headphones with your mobile phone for the first time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headphones and mobile phone. The headphones store the last 8 devices in the memory . If you try to pair more than 8 devices , the earliest pained device is replaced by the new one. 4 EN 4 Use your headphones Turn the headphones off. On/off, music/call control Press and hold for 3 seconds. Connect the headphones to a Bluetooth device Turn on your mobile phone/Bluetooth device. Press and hold the on/off button to turn the headphones on. The blue LED flashes. The headphones are reconnected to the last connected mobile phone/

Bluetooth device automatically. If the last one is not available, the headphones try to reconnect to the second last connected device. Tip If you turn on the mobile phone/Bluetooth device or activate the Bluetooth feature after turning on the headphones, you have to reconnect the headphones and mobile phone/Bluetooth device manually. Note If the headphones fail to connect to any Bluetooth device within range in 5 minutes, it will switch off automatically to save the battery life. Manage your calls and music On/off Task Turn the headphones on. Button On/off, music/call control Operation Press and hold for 1 seconds. The red LED is on and fades out. Operation Press once. Press once. Long press. Long press. Button On/off, music/call control Music control Task Play or pause music. Adjust volume. Next track. Previous track. Call control Task Pick up/hang up a call. Switch caller during a call. Button On/off, music/

call control On/off, music/call control Operation Press once. 1 beep. Press and hold for 1seconds. 1 beep. Other headphones indicator status Headphones status The headphones are connected to a Bluetooth device, while the headphones in standby mode or while you are listening to music. The headphones are ready for pairing. The headphones are on but not connected to a Bluetooth device. Indicator The blue LED flashes for every 10 seconds. The LED flashes blue. The red LED flashes for every 3 seconds If no connection can be made, the headphones will turn itself off within 5 minutes. EN 5 Low battery level. Battery is fully charged. The red LED flashes 2 times for every 3 seconds until it is out of power Red LED is off, and blue LED is on. 6 EN 5 Technical data Music time: 7 hours Talk time: 6 hours Standby time: 150 hours Normal time for a full charge: 2 hours Rechargeable lithium polymer battery (80 mAh) Bluetooth 5.0 Bluetooth mono support

(Headset Profile - HSP, Hands-Free Profile - HFP), Bluetooth stereo supported

(Advanced Audio Distribution Profile

- A2DP; Audio Video Remote Control Profile-AVRCP) Operating range: Up to 10 meters (33 feet) Digital echo & noise reduction Auto power off Note Specifications are subject to change without notice. EN 7 6 Notice Notice of compliance Notice for US The device complies with the FCC rules, Part 15. Operation is subject to the following two conditions:

This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. FCC rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter 8 EN Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Notice for Canada:

CAN ICES-3(B)/NMB-3(B) This device contains licence-exempt transmit-

ter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppe-

ment conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionne-

ment. Declaration of conformity Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com. Disposal of your old product and battery This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or visit www.recycle. philips.com. This product contains non-removable batteries:

Do not incinerate. Batteries may explode if overheated. For disposal or recycling information, please contact your local authorities or visit www.recycle.philips.com. Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. This symbol on a product means that the product is covered by European Directive 2012/19/EU. This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health. Remove the integrated battery Note Make sure the headphones are disconnected from the USB charging cable before removing the battery. If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones. Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene

(bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. Trademarks Bluetooth The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners. EN 9 The audio quality is poor and crackling noise can be heard. The Bluetooth device is out of range. Reduce the distance between your headphones and Bluetooth device, or remove obstacles between them. The audio quality is poor when streaming from the mobile phone is very slow, or audio streaming does not work at all. Make sure your mobile phone not only supports (mono) HSP/HFP but also supports A2DP (see 'Technical data' on page 7). I hear but cannot control music on my Bluetooth device (e.g. play/pause/skip forward/

backward). Make sure the Bluetooth audio source supports AVRCP (see 'Technical data' on page 7). For further support, visit www.philips.com/

support. 7 Frequently asked questions My Bluetooth headphones do not switch on. The battery level is low. Charge the headphones. I cannot pair my Bluetooth headphones with a mobile phone. The Bluetooth is disabled. Enable the Bluetooth feature on your mobile phone and turn on the mobile phone before you turn on the headphones. Pairing does not work. Make sure the headphones are in pairing mode. Follow the steps described in this user manual. Make sure that the LED light flashes blue and red alternately before you release the call/music button. Do not stop holding the button if you see the blue LED only. The mobile phone cannot find the headphones. The headphones may be connected to a previously paired device. Turn off the connected device or move it out of range. Pairing may have been reset or the headphones have been previously paired with another device. Pair the headphones with the mobile phone again as described in the user manual. My Bluetooth headphones are connected to a Bluetooth stereo enabled mobile phone, but music only plays on the mobile phone speaker. Refer to the user manual of your mobile phone. Select to listen to music through the headphones. 10 EN Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. Este produto est homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resoluo 242/2000, e atende aos requisitos tcnicas aplicados. Para maiores informaes, consulte a site da ANATEL:

www.anatel.gov.br Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. UM_TAUN102_10_EN_v2.0

Internal Photographs Model Number: TAUN102 Internal View of EUT-1 Internal View of EUT-2 Antenna Page 2 of 4 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services

(Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-3 Internal View of EUT-4 Bluetooth Chip Page 3 of 4 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services

(Guangzhou) Co., Ltd, Song Shan Lake Branch. Internal View of EUT-5 Internal View of EUT-6 Page 4 of 4 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services

(Guangzhou) Co., Ltd, Song Shan Lake Branch.

External Photographs Model Number: TAUN102 View of EUT-1 View of EUT-2 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services Page 2 of 4

(Guangzhou) Co., Ltd, Song Shan Lake Branch.

. View of EUT-3 View of EUT-4 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services Page 3 of 4

(Guangzhou) Co., Ltd, Song Shan Lake Branch.

. View of EUT-5 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch This report shall not be reproduced except in full, without the written approval of UL Verification Services Page 4 of 4

(Guangzhou) Co., Ltd, Song Shan Lake Branch.

.

Remark:

The label uses a double adhesives tape to with plastic for protection to ensure it cannot be removed. TAUN102 TAUN102BK/00 2AR2STAUN102 24589-TAUN102 XXXXXXX

XXXXX-XX-XXXXX CMIIT ID: XXXXXXXXXX

MMD Hong Kong Holding Limited Date: 2019/06/19 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. 1, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

c) make claims regarding certification only in respect of the scope for which certification has been granted;

d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

f) use certification only to indicate the products are certified as being in conformity with specified standards;

8) h) J) k) endeavor to ensure that no certificate or report nor any part thereof is used ina misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by: Benson Lai fy,

; bfp ny Company Name: MMD Hong Kong Holding Limited Contact Name: Benson Lai Title of Person: Safety & Approbation Manager Address: Units 1006-1007,10th Floor, C-Bons International Center,108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong

MMD Hong Kong Holding Limited Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2AR2STAUN102 To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards ComparfyName: MMD Hong Kong Holding Limited Contact Name: Benson Lai Title of Person: Safety & Approbation Manager Address: Units 1006-1007,10th Floor, C-Bons International Center,108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Date:2019/06/19