FCC ID: PUU-HQC2SEM 2-CHANNEL POWER MONITOR MODULE

Product Information and Regulatory Statement Important Safety Information - Read First!

Before installing, configuring, or operating any equipment, all relevant technical documentation must be read, understood, and followed. Savant technical documentation may contain important product-specific installation, mounting, and safety instructions, and can be accessed through the Savant Store. Scan the QR code or visit the URL below, enter the relevant product name or SKU in the Search Savant prompt, and select the product purchased to find documents, specifications and more. https://store.savant.com/DefaultStore/ccrz__HomePage Safety Statements Dclarations de Scurit All safety instructions below must be read, understood, and carefully followed under all applicable circumstances when working with any Savant equipment. Toutes les instructions de scurit ci-dessous doivent tre lues, comprises et soigneusement suivies dans toutes les circonstances applicables lorsque vous travaillez avec un quipement Savant. 1. Follow all input power ratings marked on product near power 1. Suivez toutes les puissances nominales indiques sur le input!

2. If fuse replacement is required, replacement fuse should match fuse rating marked on the product. 3. Do not use equipment near water. 4. Clean only with dry cloth. 5. Do not block any ventilation openings or install near any heat sources such as heat registers, stoves, radiators, amplifiers, etc. 6. Refer all servicing to qualified service personnel. Servicing is required when any part of the apparatus has been damaged in any way, or fails to operate normally for any reason. 7. Use only attachments/accessories specified by the manufacturer, following all relevant safety precautions for any such attachments/accessories. 8. For applicable equipment, use the included power cord with the grounding prong intact to insure proper grounding of the device. 9. If the provided plug does not fit the desired outlet, contact a licensed electrician to replace the obsolete outlet. 10. Protect any power cord from being walked on, pinched, strained, or otherwise potentially damaged, especially at the outlet or device connections. 11. Disconnect any outlet powered apparatus from its power source during lightning storms or when unused for long periods of time. 12. To completely disconnect equipment from AC mains power, disconnect the power supply cord plug from the AC receptacle on the device. 13. For any hardwired or fixed in-wall apparatus, carefully follow all wiring diagrams and instructions. All electrical wiring and servicing should be performed by a properly licensed electrician. produit prs de la puissance absorbe!

2. Si le remplacement du fusible est ncessaire, le fusible de remplacement doit correspondre la valeur nominale du fusible indique sur le produit. 3. Nutilisez pas dquipement prs de leau. 4. Nettoyer uniquement avec un chiffon sec. 5. Ne bloquez pas les ouvertures de ventilation et ninstallez pas proximit de sources de chaleur telles que les registres de chaleur, les cuisinires, les radiateurs, les amplificateurs, etc. 6. Confiez toutes les rparations un technicien qualifi. Un entretien est requis lorsquune partie de lappareil a t endommage de quelque manire que ce soit ou ne fonctionne pas normalement pour une raison quelconque. 7. Utilisez uniquement les attachements / accessoires spcifis par le fabricant, en suivant toutes les prcautions de scurit applicables ces attachements / accessoires. 8. Pour lquipement applicable, utilisez le cordon dalimentation inclus avec la broche de mise la terre intacte pour assurer une mise la terre correcte de lappareil. 9. Si la fiche fournie ne correspond pas la prise souhaite, contactez un lectricien agr pour remplacer la prise obsolte. 10. Protgez tout cordon dalimentation contre les pitinements, les pincements, les tensions ou autres dommages potentiels, en particulier au niveau de la prise ou des connexions de lappareil. 11. Dbranchez tout appareil aliment par une prise de courant de sa source dalimentation pendant les orages ou lorsquil nest pas utilis pendant de longues priodes. 12. Pour dconnecter compltement lquipement du secteur, dbranchez la fiche du cordon dalimentation de la prise secteur de lappareil. 13. Pour tout appareil encastr ou cbl, suivez attentivement tous les schmas de cblage et les instructions. Tout le cblage lectrique et lentretien doivent tre effectus par un lectricien dment agr. IMPORTANT NOTES:

For product mounting, installation, safety instructions, technical specifications, and more, refer to the product Quick Reference Guide, available via the link or QR code noted above. For regulatory and compliance information, see reverse of this sheet and/or product packaging. 1 of 2 45 Perseverance Way, Hyannis, MA 02601 Savant.com | 508.683.2500 Savant Product Regulatory Statement | 009-1950-02220127 | 2022 Savant Systems, Inc. FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for CLASS B digital devices, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correcting the interference with one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect this equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement - Wireless and Handheld Devices Only This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. FCC and IC Identifier - Devices with Integrated Screen or User Interface Only This device electronically displays the FCC declaration of conformity logo as well as the FCC and IC identifier. This information can be found on the device by accessing:

(Service menu) > About (A propos de) IC Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003/NMB-003. This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios. The Country Code Selection feature is disabled for products marketed in the US/Canada. Dclaration IC Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage, et 2. Cet appareil accepter toute interfrence, y compris les interfrences pouvant provoquer fonctionnement indsirable dappareil. Dclaration dexposition aux radiations Cet quipement est conforme aux limites dexposition aux radiations de la FCC dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. Identificateur de la FCC et dLc Ce priphrique par voie lectronique affiche le logo de dclaration de conformit FCC ainsi que lidentificateur de la FCC et dIC. Cette information peut tre trouve sur le terminal en accdant :

(Menu de service) > About (A propos de) 2 of 2 45 Perseverance Way, Hyannis, MA 02601 Savant.com | 508.683.2500 Savant Product Regulatory Statement | 009-1950-02220127 | 2022 Savant Systems, Inc. Smart Energy Monitor Module (Supports 1-inch On-Center Load Centers) Quick Reference and Installation Guide Box Contents

(1) Smart Energy Monitor Module (SEM) GPM-H2SEM-xx w/Pigtail type neutral

(1) 4-pin screw down plug-in connector (028-9395)

(1) Product Information and Regulatory Insert (009-1950)

(1) Quick Reference and Installation Guide (this document) Accessories Current Transformers ACTL-1250-250 Opt CO.2 250 Amp ACTL-1250-400 Opt CO.2 400 Amp ACTL-1250-600 Opt CO.2 600 Amp Specifications Environmental Temperature Humidity Location 32 to 104 F (0 to 40 C) 5% to 85% Relative Humidity (non-condensing) Indoor Use Only Dimensions and Weights Module Shipping Length Width Height 4.49 in.

(11.41 cm) 7.48 in.

(19.0 cm) 1.98 in.

(5.03 cm) 4.17 in.

(10.6 cm) 2.78 in.

(7.06 cm) 1.69 in.

(4.29 cm) Weight

.54 lbs

(.24 kg) 1.0 lbs.

(.45 kg) Power Input Power

(powers the module) 120V AC (+/- 10%) @ 60 Hz, 0.1A (max) Signal Input 0.333V AC @ 60Hz Type of Action Type 1 action Standards Wireless Bluetooth 5 Low Energy (BLE) 2.4 GHz radio frequency This meter will be tested and certified to the following standards:

ANSI C12.20-2015 American National Standard for Electricity Meters - 0.5 Accuracy Class ANSI C12.1-2014 Regulatory Safety and Emissions American National Standard for Electric Meters

- Code of electricity Metering FCC Part 15 UL ICES 003 Contains FCC ID:

PUU-HQC2SEM Contains IC:

RoHS 10798A-HQC2SEM Compliant Recommended Load Center Types Refer to the Features section to the right for compatibility. Electrical and Safety Characteristics Pollution Degree 2 Purpose of Control Energy Monitoring Software Impulse Voltage Class A 2500V Construction of Control Open Type Independently mounted for flush mounting Minimum Supported Release Savant OS da Vinci 10.x Descriptions A D O N OT PRESS O N SCREEN REM OVE AFTER INSTALLATIO N P AIR B C O

S M A R T E N E R G Y M O NIT O R IN D O O R U S E O N LY M O D U L E IN P U T: 12 0 V A C 6 0 H z S E RIA L IN P U T: 0.333vac 6 0 H z

#18-2 4 A W G Min. 10 5C C u O nly G P M -H 2S E M C T C O N N E C TIO N S IC 10 79 8 A-H Q C S E M F C C ID P U U-H Q C S E M 1 2 O O

O

D E Multi-Page LCD screen that offers the following information:

A Real-time energy usage. Firmware and Mac Address of the module. UID of the connected Host Real-time Bluetooth status connectivity icon. Module set-up and calibration screens. PAIR Button - The PAIR button is a multi-use button. The duration that the button is pressed and held determines the function that gets initiated:

B Press and Release - Cycles through the screens available on the LCD (POWER > POWER > INFO 1 > INFO 2). Press and hold - Press and hold for 2 second to put the module into pairing mode. Press and hold for greater than 5 seconds to reset the module. CT Connections - Connect a current transformer to each CT Connection input port labeled 1 and 2, observing polarity when making connections. Refer to the Install the Current Transformer section later in the document for additional wiring information. Pigtail Neutral - Connect the pigtail type neutral wire to the neutral bar in the breaker panel. 120V AC Connection - Plug the module onto the 120V AC bus bar in the breaker panel. The voltage on this connection powers the module. C D E Features The GPM-H2SEM-00 Smart Energy Monitor modules is compatible with Schneider Homeline, Eaton BR, Siemens, and Powermark Gold load centers with a one-inch on-center bus bar. Energy monitoring; +/- 0.5% revenue grade accuracy / 1 sec sample time. The module communicates with a Panel Bridge Controller or Savant Power Director using Bluetooth Low Energy (BLE) technology. Color LCD display for easy identification. Smart Energy Monitor - QRG | 009-2245-00 Copyright 2022 Savant Systems, Inc | 220930 1 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 ELECTRIC SHOCK! The 120V AC, 60 Hz source poses an electrical shock hazard that has the potential to cause serious injury to installers and end users. CHOC LECTRIQUE! La source alimentation lectrique de 120 V AC, 60 Hz prsente un risque dlectrocution susceptible de causer des blessures graves aux installateurs et aux utilisateurs finaux. CAUTION! Risk of Electric Shock - More than one disconnect switch may be required to de-energize the device before servicing. Always disconnect the power to the module before making any connections. ATTENTION! Risque de choc lectrique - Plus dun interrupteur de dconnexion peut tre ncessaire pour mettre lappareil hors tension avant lentretien. Dbranchez toujours lalimentation du module avant deffectuer des connexions. IMPORTANT! A licensed electrician is required to install any of Savants Power and Energy Monitoring Modules. IMPORTANT! Un lectricien agr est requis pour installer lun des modules de surveillance de lalimentation et de lnergie de Savant. Important Information Each Smart Energy Monitor requires two spaces in an electrical breaker panel. All wiring in the United States must be installed in accordance with the latest adopted edition of the National Electrical Code

(ANSI/NFPA 70, NEC) All wiring in Canada must be installed in accordance with the latest adopted edition of the Canadian Electrical Code (CSA C222.2 CEC, Part 1) and any provincial or local requirements. Use only Savant approved current transformers. A list of supported transformers is available in the Accessories section on the previous page. The largest current transformer offered from Savant supports wire up to a 750 kcmil conductor (with jacket is just under 1 inch in diameter). Installation into Breaker Panel 1. Remove power from the breaker panel by switching off the panels main breaker. 2. Position and install the Smart Energy Monitor Module into the slots where it will be installed. Press firmly until fully seated onto the appropriate bus bars. 3. The next few sections describe how to install and wire a current transformer to the Smart Energy Monitor module. Install the Current Transformer The GPM-H2SEM module supports connecting up to two Savant-

approved current transformers. See the approved list on the previous page. Instructions on wiring and orienting the current transformer are explained below. 1. Toggle the electrical panels main breaker Off to remove power from the panel. 2. Remove the panels front cover and set it aside. Verify that power is removed from the circuit breakers using a voltage tester. 3. Separate the current transformer by squeezing the knurled panel and pulling/rotating the top open. 4. Place the current transformers around each of the conductors being monitored. Orient the current transformer so the arrow in the middle points towards the source i.e., breaker or utility meter. 5. Close the current transformer around the conductor. For added security, wrap a cable tie around the CT or run the tie through the loop on the front. 6. Route the twisted black and white wires around the breaker panel back to the Smart Energy Monitor module. Route the wires so they dont directly come in contact with a live bus bar or terminal. 7. Observing polarity, insert the wires into the supplied 4-pin connector and secure by turning screws clockwise. See the Making Connections section in this document for information on attaching wires to the connector. Making Connections 1. Remove power if power is applied. 2. Pull to remove the terminal block from the Smart Energy Monitors rear panel. 3. With a small flat-bladed screwdriver, turn the screws on the top of the connector counterclockwise until the silver crimps on the front of the connector open enough to slide the wire into the square slot. 4. Strip back the insulation of each wire to 1/4 inch (6.5 mm). Insert the stripped wire into the proper port. Do not allow more than 1/8 inch (3.2 mm) of bare wire exposed. See image. Less than inch bare wire exposed 5. Turn the screws clockwise until the silver crimps tighten around the wire. Tug on the wire a bit to verify the wire is installed securely. 6. Continue until all wires are installed. 7. Plug the terminal block into the appropriate port on the Smart Energy Monitor. 8. Repeat steps 2-7 for all wires from the current transformer. 9. Reapply power. CT1 CT2

(+) GND POS White Black

(+) POS White

(-) GND Black HELPFUL: A negative current will be measured if the wires are reversed or the current transformer is installed backward. Additional Information Savant Power Deployment Guide - Sol-Ark 8. Repeat steps 3-7 to install a second current transformer if needed. 9. Ensure the 4-pin connector is fully seated into the SEM module and tighten the screws to .18 ft-lb (.25 N-m) max. 10. Toggle the main breaker back to the On position and re-apply power to the electrical panel. The Current Transformer and Smart Energy Monitor module are ready to monitor the power consumed by the circuit the CT is monitoring. Smart Energy Monitor - QRG | 009-2245-00 Copyright 2022 Savant Systems, Inc | 220930 2 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 System Overview Local Lan Wi-Fi

(if needed) Bluetooth to SEM Modules Bluetooth to SEM Modules Power From the Utility SEM Module Commuicates with Director or PBC over Bluetooth Current Transformers MAIN BREAKER

1

2

C T C O N N E C T O N S I G P M

H 2 S E M M O N T O R I S M A R T E N E R G Y P A R I BREAKER Current Transformers

(Twisted Pair) Current Transformers I R A P Y G R E N E T R A M S I R O T N O M M E S 2 H

M P G I S N O T C E N N O C T C

2

1

BREAKER BREAKER BREAKER Current Transformers

(Twisted Pair) Breaker Panel SEM Display Descriptions Smart Energy Monitor - QRG | 009-2245-00 Copyright 2022 Savant Systems, Inc | 220930 3 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 NOTES Smart Energy Monitor - QRG | 009-2245-00 Copyright 2022 Savant Systems, Inc | 220930 4 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 Smart Energy Monitor Module (Supports QO Style Load Centers) Quick Reference and Installation Guide Box Contents

(1) Smart Energy Monitor Module (SEM) GPM-QP2SEM-xx w/Plug-on neutral GPM-Q2SEM-xx w/Pigtail type neutral

(1) 4-pin screw down plug-in connector (028-9395)

(1) Product Information and Regulatory Insert (009-1950)

(1) Quick Reference and Installation Guide (this document) Accessories Current Transformers ACTL-1250-250 Opt CO.2 250 Amp ACTL-1250-400 Opt CO.2 400 Amp ACTL-1250-600 Opt CO.2 600 Amp Specifications Environmental Temperature 32 to 104 F (0 to 40 C) Humidity 5% to 85% Relative Humidity (non-condensing) Location Dimensions and Weights Indoor Use Only Length Width Module

(QO) Shipping 4.97 in.

(12.63 cm) 7.50 in.

(19.05 cm) 1.45 in.

(3.68 cm) Height 2.60 in.

(6.61 cm) 4.30 in.

(10.92 cm) 1.71 in.

(4.34 cm) Weight

.5 lbs

(.23 kg) 1.0 lbs.

(.45 kg) Power Input Power

(powers the module) 120V AC (+/- 10%) @ 60 Hz, 0.1A (max) Signal Input 0.333V AC @ 60Hz Type of Action Type 1 action Standards Wireless Bluetooth 5 Low Energy (BLE) 2.4 GHz radio frequency This meter will be tested and certified to the following standards:

ANSI C12.20-2015 American National Standard for Electricity Meters - 0.5 Accuracy Class ANSI C12.1-2014 Regulatory Safety and Emissions American National Standard for Electric Meters

- Code of electricity Metering FCC Part 15 UL ICES 003 Contains FCC ID:

PUU-HQC2SEM Contains IC:

RoHS 10798A-HQC2SEM Compliant Recommended Load Center Types Refer to the Features section to the right for compatibility. Electrical and Safety Characteristics Pollution Degree 2 Purpose of Control Energy Monitoring Software Impulse Voltage Class A 2500V Construction of Control Open Type Independently mounted for flush mounting Minimum Supported Release Savant OS da Vinci 10.x Descriptions A E D O N OT PRESS O N SCREEN REM OVE AFTER INSTALLATIO N P AIR B C O

S M A R T E N E R G Y M O NIT O R IN D O O R U S E O N LY M O D U L E IN P U T: 12 0 V A C 6 0 H z S E RIA L IN P U T: 0.333vac 6 0 H z

#18-2 4 A W G Min. 10 5C C u O nly G P M -Q 2S E M C T C O N N E C TIO N S IC 10 79 8 A-H Q C S E M F C C ID P U U-H Q C S E M 1 2 O O

O

D Multi-Page LCD screen that offers the following information:

A Real-time energy usage. Firmware and Mac Address of the module. UID of the connected Host Real-time Bluetooth status connectivity icon. Module set-up and calibration screens. PAIR Button - The PAIR button is a multi-use button. The duration that the button is pressed and held determines the function that gets initiated:

B Press and Release - Cycles through the screens available on the LCD (POWER > POWER > INFO 1 > INFO 2). Press and hold - Press and hold for 2 second to put the module into pairing mode. Press and hold for greater than 5 seconds to reset the module. CT Connections - Connect a current transformer to each CT Connection input port labeled 1 and 2, observing polarity when making connections. Refer to the Install the Current Transformer section later in the document for additional wiring information. Neutral - The model number of the module determines the type of neutral connection on the module:

Plug-on Neutral - Positioned on the bottom of the module is a neutral clip that plugs directly onto the neutral bar. Pigtail Neutral - A neutral wire protrudes from the modules rear and gets wired to the neutral bar in the breaker panel. 120V AC Connection - Plug the module onto the 120V AC bus bar in the breaker panel. The voltage on this connection powers the module. C D E Features The GPM-Q2SEM-00 and GPM-QP2SEM Smart Energy Monitor modules are compatible with Schneider/Electric Square D QO load centers. Energy monitoring; +/- 0.5% revenue grade accuracy / 1 sec sample time. The module communicates with a Panel Bridge Controller or Savant Power Director using Bluetooth Low Energy (BLE) technology. Color LCD display for easy identification. Smart Energy Monitor (QO) - QRG | 009-2240-00 Copyright 2022 Savant Systems, Inc | 221005 1 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 ELECTRIC SHOCK! The 120V AC, 60 Hz source poses an electrical shock hazard that has the potential to cause serious injury to installers and end users. CHOC LECTRIQUE! La source alimentation lectrique de 120 V AC, 60 Hz prsente un risque dlectrocution susceptible de causer des blessures graves aux installateurs et aux utilisateurs finaux. CAUTION! Risk of Electric Shock - More than one disconnect switch may be required to de-energize the device before servicing. Always disconnect the power to the module before making any connections.ring Modules. ATTENTION! Risque de choc lectrique - Plus dun interrupteur de dconnexion peut tre ncessaire pour mettre lappareil hors tension avant lentretien. Dbranchez toujours lalimentation du module avant deffectuer des connexions. IMPORTANT! A licensed electrician is required to install any of Savants Power and Energy Monitoring Modules. IMPORTANT! Un lectricien agr est requis pour installer lun des modules de surveillance de lalimentation et de lnergie de Savant. Important Information Each Smart Energy Monitor requires two spaces in an electrical breaker panel. All wiring in the United States must be installed in accordance with the latest adopted edition of the National Electrical Code

(ANSI/NFPA 70, NEC) All wiring in Canada must be installed in accordance with the latest adopted edition of the Canadian Electrical Code (CSA C222.2 CEC, Part 1) and any provincial or local requirements. Use only Savant approved current transformers. A list of supported transformers is available in the Accessories section on the previous page. The largest current transformer offered from Savant supports wire up to a 750 kcmil conductor (with jacket is just under 1 inch in diameter). Installation into Breaker Panel 1. Remove power from the breaker panel by switching off the panels main breaker. 2. Position and install the Smart Energy Monitor Module into the slots where it will be installed. Press firmly until fully seated onto the appropriate bus bars. 3. The next few sections describe how to install and wire a current transformer to the Smart Energy Monitor module. Install the Current Transformer The GPM-Q2SEM and GPM-QP2SEM module supports connecting up to two Savant-approved current transformers. See the approved list on the previous page. Instructions on wiring and orienting the transformer are explained below. 1. Toggle the electrical panels main breaker Off to remove power from the panel. 2. Remove the panels front cover and set it aside. Verify that power is removed from the circuit breakers using a voltage tester. 3. Separate the current transformer by squeezing the knurled panel and pulling/rotating the top open. 4. Place the current transformers around each of the conductors being monitored. Orient the current transformer so the arrow in the middle points towards the source i.e., breaker or utility meter. 5. Close the current transformer around the conductor. For added security, wrap a cable tie around the CT or run it through the loops on the front. 6. Route the twisted black and white wires around the breaker panel back to the Smart Energy Monitor module. Route the wires so they dont directly come in contact with a live bus bar or terminal. 7. Observing polarity, insert the wires into the supplied 4-pin connector and secure by turning screws clockwise. See the Making Connections section in this document for more information on attaching the wires to the connector. Making Connections 1. Remove power if power is applied. 2. Pull to remove the terminal block from the Smart Energy Monitors rear panel. 3. With a small flat-bladed screwdriver, turn the screws on the top of the connector counterclockwise until the silver crimps on the front of the connector open enough to slide the wire into the square slot. 4. Strip back the insulation of each wire to 1/4 inch (6.5 mm). Insert the stripped wire into the proper port. Do not allow more than 1/8 inch (3.2 mm) of bare wire exposed. See image. Less than inch bare wire exposed 5. Turn the screws clockwise until the silver crimps tighten around the wire. Tug on the wire a bit to verify the wire is installed securely. 6. Continue until all wires are installed. 7. Plug the terminal block into the appropriate port on the Smart Energy Monitor. 8. Repeat steps 2-7 for all wires from the current transformer. 9. Reapply power. CT1 CT2

(+) GND POS White Black

(+) POS White

(-) GND Black HELPFUL: A negative current will be measured if the wires are reversed or the current transformer is installed backward. Additional Information Savant Power Deployment Guide - Sol-Ark 8. Repeat steps 3-7 to install a second current transformer if needed. 9. Ensure the 4-pin connector is fully seated into the SEM module and tighten the connectors mounting screws to .18 ft-lb (.25 N-m) max. 10. Toggle the main breaker back to the On position and re-apply power to the electrical panel. The Current Transformer and Smart Energy Monitor module are ready to monitor the power consumed by the circuit the CT is monitoring. Smart Energy Monitor (QO) - QRG | 009-2240-00 Copyright 2022 Savant Systems, Inc | 221005 2 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 System Overview Local Lan Wi-Fi

(if needed) Bluetooth to SEM Modules Bluetooth to SEM Modules Power From the Utility SEM Module Commuicates with a Director/Directlite or PBC over Bluetooth Current Transformers MAIN BREAKER

1

2

C T C O N N E C T O N S I

G P M Q 2 S E M M O N T O R I S M A R T E N E R G Y P A R I BREAKER Current Transformers I R A P Y G R E N E T R A M S I R O T N O M M E S 2 Q M P G

I S N O T C E N N O C T C

2

1

BREAKER BREAKER BREAKER Current Transformer Cables

(Twisted Pair) Current Transformer Cable

(Twisted Pair) Electrical Panel SEM Display Descriptions Smart Energy Monitor (QO) - QRG | 009-2240-00 Copyright 2022 Savant Systems, Inc | 221005 3 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 NOTES Smart Energy Monitor (QO) - QRG | 009-2240-00 Copyright 2022 Savant Systems, Inc | 221005 4 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 Smart Energy Monitor Module (Supports Eaton CH Style Load Centers) Quick Reference and Installation Guide Box Contents

(1) Smart Energy Monitor Module (SEM) GPM-CP2SEM-xx w/Plug-on type neutral GPM-C2SEM-xx w/Pigtail type neutral

(1) 4-pin screw down plug-in connector (028-9395)

(1) Product Information and Regulatory Insert (009-1950)

(1) Quick Reference and Installation Guide (this document) Accessories Current Transformers ACTL-1250-250 Opt CO.2 250 Amp ACTL-1250-400 Opt CO.2 400 Amp ACTL-1250-600 Opt CO.2 600 Amp Descriptions A E D O N OT PRESS O N SCREEN REM OVE AFTER INSTALLATIO N P AIR B C O

S M A R T E N E R G Y M O NIT O R IN D O O R U S E O N LY M O D U L E IN P U T: 12 0 V A C 6 0 H z S E RIA L IN P U T: 0.333vac 6 0 H z

#18-2 4 A W G Min. 10 5C C u O nly G P M -C 2S E M C T C O N N E C TIO N S IC 10 79 8 A-H Q C S E M F C C ID P U U-H Q C S E M 1 2 O O

O

D 32 to 104 F (0 to 40 C) 5% to 85% Relative Humidity (non-condensing) Multi-Page LCD screen that offers the following information:

Specifications Environmental Temperature Humidity Location Indoor Use Only Dimensions and Weights Module Shipping Length 4.49 in.

(11.4 cm) 7.48 in.

(19.0 cm) Width 1.97 in.

(5.0 cm) Height 2.76 in.

(7.0 cm) 4.17 in.

(10.60 cm) 1.69 in.

(4.29 cm) Weight

.5 lbs

(.23 kg) 1.0 lbs.

(.45 kg) Power Input Power

(powers the module) 120V AC (+/- 10%) @ 60 Hz, 0.1A (max) Signal Input 0.333V AC @ 60Hz Type of Action Type 1 action Standards Wireless Bluetooth 5 Low Energy (BLE) 2.4 GHz radio frequency This meter will be tested and certified to the following standards:

ANSI C12.20-2015 American National Standard for Electricity Meters - 0.5 Accuracy Class ANSI C12.1-2014 Regulatory Safety and Emissions American National Standard for Electric Meters

- Code of electricity Metering FCC Part 15 UL ICES 003 Contains FCC ID:

PUU-HQC2SEM Contains IC:

RoHS 10798A-HQC2SEM Compliant Recommended Load Center Types Refer to the Features section to the right for compatibility. Electrical and Safety Characteristics Pollution Degree 2 Purpose of Control Energy Monitoring Software Impulse Voltage Class A 2500V Construction of Control Open Type Independently mounted for flush mounting Minimum Supported Release Savant OS da Vinci 10.x A Real-time energy usage. Firmware and Mac Address of the module. UID of the connected Host Real-time Bluetooth status connectivity icon. Module set-up and calibration screens. PAIR Button - The PAIR button is a multi-use button. The duration that the button is pressed and held determines the function that gets initiated:

B Press and Release - Cycles through the screens available on the LCD (POWER > POWER > INFO 1 > INFO 2). Press and hold - Press and hold for 2 second to put the module into pairing mode. Press and hold for greater than 5 seconds to reset the module. CT Connections - Connect a current transformer to each CT Connection input port labeled 1 and 2, observing polarity when making connections. Refer to the Install the Current Transformer section later in the document for additional wiring information. Neutral - The model number of the module determines the type of neutral connection:

Plug-on Neutral - Positioned on the bottom of the module is a neutral clip that plugs directly onto the neutral bar. Pigtail Neutral - A neutral wire protrudes from the modules rear and gets wired to the neutral bar in the breaker panel. 120V AC Connection - Plug the module onto the 120V AC bus bar in the breaker panel. The voltage on this connection powers the module. C D E Features All Eaton CH style Smart Energy Modules are compatible with Eaton CH 3/4 inch load centers. Energy monitoring; +/- 0.5% revenue grade accuracy / 1 sec sample time. The module communicates with a Panel Bridge Controller or Savant Power Director using Bluetooth Low Energy (BLE) technology. Color LCD display for easy identification. Smart Energy Monitor - QRG | 009-2241-00 Copyright 2022 Savant Systems, Inc | 220930 1 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 ELECTRIC SHOCK! The 120V AC, 60 Hz source poses an electrical shock hazard that has the potential to cause serious injury to installers and end users. CHOC LECTRIQUE! La source alimentation lectrique de 120 V AC, 60 Hz prsente un risque dlectrocution susceptible de causer des blessures graves aux installateurs et aux utilisateurs finaux. CAUTION! Risk of Electric Shock - More than one disconnect switch may be required to de-energize the device before servicing. Always disconnect the power to the module before making any connections. ATTENTION! Risque de choc lectrique - Plus dun interrupteur de dconnexion peut tre ncessaire pour mettre lappareil hors tension avant lentretien. Dbranchez toujours lalimentation du module avant deffectuer des connexions. IMPORTANT! A licensed electrician is required to install any of Savants Power and Energy Monitoring Modules. IMPORTANT! Un lectricien agr est requis pour installer lun des modules de surveillance de lalimentation et de lnergie de Savant. Important Information Each Smart Energy Monitor requires two spaces in an electrical breaker panel. All wiring in the United States must be installed in accordance with the latest adopted edition of the National Electrical Code

(ANSI/NFPA 70, NEC) All wiring in Canada must be installed in accordance with the latest adopted edition of the Canadian Electrical Code (CSA C222.2 CEC, Part 1) and any provincial or local requirements. Use only Savant approved current transformers. A list of supported transformers is available in the Accessories section on the previous page. The largest current transformer offered from Savant supports wire up to a 750 kcmil conductor (with jacket is just under 1 inch in diameter). Installation into Breaker Panel 1. Remove power from the breaker panel by switching off the panels main breaker. 2. Position and install the Smart Energy Monitor Module into the slots where it will be installed. Press firmly until fully seated onto the appropriate bus bars. 3. The next few sections describe how to install and wire a current transformer to the Smart Energy Monitor module. Install the Current Transformer Making Connections The GPM-C2SEM and GPM-CP2SEM modules support connecting up to two Savant-approved current transformers. See the approved list on the previous page. Information on connecting and orienting the current transformer is explained below. 1. Toggle the electrical panels main breaker Off to remove power from the panel. 2. Remove the panels front cover and set it aside. Verify that power was removed from the circuit breakers using a voltage tester. 3. Separate the current transformer by squeezing the knurled panel and pulling/rotating the top open. 4. Place the current transformers around each of the conductors being monitored. Orient the current transformer so the arrow in the middle points towards the source i.e., breaker or utility meter. 5. Close the current transformer around the conductor. For added security, wrap a cable tie around the CT or run it through the loops on the front. 6. Route the twisted black and white wires around the breaker panel back to the Smart Energy Monitor module. Route the wires so they dont directly come in contact with a live bus bar or terminal. 7. Observing polarity, insert the wires into the supplied 4-pin connector and secure by turning screws clockwise. See the Making Connections section in this document for information on attaching wires to the connector. 1. Remove power if power is applied. 2. Pull to remove the terminal block from the Smart Energy Monitors rear panel. 3. With a small flat-bladed screwdriver, turn the screws on the top of the connector counterclockwise until the silver crimps on the front of the connector open enough to slide the wire into the square slot. 4. Strip back the insulation of each wire to 1/4 inch (6.5 mm). Insert the stripped wire into the proper port. Do not allow more than 1/8 inch (3.2 mm) of bare wire exposed. See image. Less than inch bare wire exposed 5. Turn the screws clockwise until the silver crimps tighten around the wire. Tug on the wire a bit to verify the wire is installed securely. 6. Continue until all wires are installed. 7. Plug the terminal block into the appropriate port on the Smart Energy Monitor. 8. Repeat steps 2-7 for all wires from the current transformer. 9. Reapply power. CT1 CT2

(+) GND POS White Black

(+) POS White

(-) GND Black HELPFUL: A negative current will be measured if the wires are reversed or the current transformer is installed backward. Additional Information Savant Power Deployment Guide - Sol-Ark 8. Repeat steps 3-7 to install a second current transformer if needed. 9. Ensure the 4-pin connector is fully seated into the SEM module and tighten to .18 ft-lb (.25 N-m) max. 10. Toggle the main breaker back to the On position and re-apply power to the electrical panel. The Current Transformer and Smart Energy Monitor module are ready to monitor the power consumed by the circuit the CT is monitoring. Smart Energy Monitor - QRG | 009-2241-00 Copyright 2022 Savant Systems, Inc | 220930 2 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 System Overview Local Lan Wi-Fi

(if needed) Bluetooth to SEM Modules Bluetooth to SEM Modules Power From the Utility SEM Module Commuicates with a Director/Directlite or PBC over Bluetooth Current Transformers MAIN BREAKER

1

2

C T C O N N E C T O N S I G P M

C 2 S E M M O N T O R I S M A R T E N E R G Y P A R I BREAKER Current Transformers I R A P Y G R E N E T R A M S I R O T N O M M E S 2 C

M P G I S N O T C E N N O C T C

2

1

BREAKER BREAKER BREAKER Current Transformer Cables

(Twisted Pair) Current Transformer Cable

(Twisted Pair) SEM Display Descriptions Electrical Panel Smart Energy Monitor - QRG | 009-2241-00 Copyright 2022 Savant Systems, Inc | 220930 3 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500 NOTES Smart Energy Monitor - QRG | 009-2241-00 Copyright 2022 Savant Systems, Inc | 220930 4 of 4 45 Perseverance Way, Hyannis MA 02601 Savant.com | 508.683.2500

Label location:

1 L E B A L 2 L E B A L REV 00 01 CREATOR ZWH UA ECO #

13202 13188 DATE 06JUNE22 20SEP22 DESCRIPTION INITIAL CREATION UPDATE FORMAT, ADD REGULATORY INFO 33.6 SMART ENERGY MONITOR GPM-H2SEM INDOOR USE ONLY MODULE INPUT: 120VAC 60Hz SIGNAL INPUT: 0.333VAC 60Hz 45.9

#18-24 AWG Min. 105C Cu ONLY E523609 HOME AUTOMATION EQUIPMENT IC: 10798A-HQC2SEM FCC ID: PUU-HQC2SEM CT CONNECTIONS 1 2

NOTES: UNLESS OTHERWISE SPECIFIED 1. USE 3-D SOURCE FOR FABRICATION. THIS DRAWING IS TO BE USED FOR PART INSPECTION AND CRITICAL DIMENSIONS THAT AFFECT FIT, FORM AND FUNCTION 2.MARK PART NUMBER, REV, DATE, MANUFACTURER ON:

A. BULK PACKAGING B. ON PRODUCT AS SHOWN 3. ADHESIVE 3M 467 4. COLOR: SILVER BACKGROUND WITH BLACK C TEXT 5. USE M/N PER P.O. SCREW TORQUE DATA SIZE/ITEM TORQUE VALUE TOLERANCE DATA TABLE UNLESS OTHERWISE SPECIFIED. MM

.5

.3

.1 AS NOTED IN AS NOTED

` .030

` .015

` .005

` 1 DEG.

` 10%

X X.X X.XX X.XXX ANGLE TORQUE MATERIAL:

SILVER -

PERMANENT ADHESIVE COLOR:

SEE NOTE SAVANT SYSTEMS LLC PROPRIETARY & CONFIDENTIAL TITLE 45 PERSERVERANCE WAY HYANNIS, MA 02601 THIS DOCUMENT CONTAINS COMPANY PROPRIETARYINFORMATION AND IS NOT TO BE REPRODUCED OR DISTRIBUTED WITHOUT PRIOR AUTHORIZATION 1-INCH SMART ENERGY MONITOR, PRODUCT LABEL SIZE B SCALE UNITS MM 1:1 DWG NO 083-1001-00 REV 01 SHEET 1 OF 1 M/N: GPM-H2SEM-00 S/N: XXXXXXXXXXXX REV: XX 11.00mm UID: XXXXXXXXXXXXXXXX MADE IN CHINA 33.00mm REV 00 01 CREATOR ZWH UA ECO #

13279 13188 DATE 06JUNE22 20SEP22 DESCRIPTION INITIAL CREATION UPDATE FORMAT, ADD REGULATORY INFO 33.6 SMART ENERGY MONITOR GPM-Q2SEM INDOOR USE ONLY MODULE INPUT: 120VAC 60Hz SIGNAL INPUT: 0.333VAC 60Hz 45.9

#18-24 AWG Min. 105C Cu ONLY E523609 HOME AUTOMATION EQUIPMENT IC: 10798A-HQC2SEM FCC ID: PUU-HQC2SEM CT CONNECTIONS 1 2

NOTES: UNLESS OTHERWISE SPECIFIED 1. USE 3-D SOURCE FOR FABRICATION. THIS DRAWING IS TO BE USED FOR PART INSPECTION AND CRITICAL DIMENSIONS THAT AFFECT FIT, FORM AND FUNCTION 2.MARK PART NUMBER, REV, DATE, MANUFACTURER ON:

A. BULK PACKAGING B. ON PRODUCT AS SHOWN 3. ADHESIVE 3M 467 4. COLOR: SILVER BACKGROUND WITH BLACK C TEXT 5. USE M/N PER P.O. SCREW TORQUE DATA SIZE/ITEM TORQUE VALUE TOLERANCE DATA TABLE UNLESS OTHERWISE SPECIFIED. MM

.5

.3

.1 AS NOTED IN AS NOTED

` .030

` .015

` .005

` 1 DEG.

` 10%

X X.X X.XX X.XXX ANGLE TORQUE MATERIAL:

SILVER -

PERMANENT ADHESIVE COLOR:

SEE NOTE SAVANT SYSTEMS LLC PROPRIETARY & CONFIDENTIAL TITLE 45 PERSERVERANCE WAY HYANNIS, MA 02601 THIS DOCUMENT CONTAINS COMPANY PROPRIETARYINFORMATION AND IS NOT TO BE REPRODUCED OR DISTRIBUTED WITHOUT PRIOR AUTHORIZATION QO SMART ENERGY MONITOR, PRODUCT LABEL SIZE B SCALE UNITS MM 1:1 DWG NO 083-1005-00 REV 01 SHEET 1 OF 1 M/N: GPM-Q2SEM-00 REV: XX S/N: XXXXXXXXXXXX UID: XXXXXXXXXXXXXXXX MADE IN CHINA 33.00mm 11.00mm REV 00 01 CREATOR ZWH UA ECO #

13279 13188 DATE 18AUG22 20SEP22 DESCRIPTION INITIAL CREATION UPDATE FORMAT, ADD REGULATORY INFO 33.6 SMART ENERGY MONITOR GPM-QP2SEM INDOOR USE ONLY MODULE INPUT: 120VAC 60Hz SIGNAL INPUT: 0.333VAC 60Hz 45.9

#18-24 AWG Min. 105C Cu ONLY E523609 HOME AUTOMATION EQUIPMENT IC: 10798A-HQC2SEM FCC ID: PUU-HQC2SEM CT CONNECTIONS 1 2

NOTES: UNLESS OTHERWISE SPECIFIED 1. USE 3-D SOURCE FOR FABRICATION. THIS DRAWING IS TO BE USED FOR PART INSPECTION AND CRITICAL DIMENSIONS THAT AFFECT FIT, FORM AND FUNCTION 2.MARK PART NUMBER, REV, DATE, MANUFACTURER ON:

A. BULK PACKAGING B. ON PRODUCT AS SHOWN 3. ADHESIVE 3M 467 4. COLOR: SILVER BACKGROUND WITH BLACK C TEXT 5. USE M/N PER P.O. SCREW TORQUE DATA SIZE/ITEM TORQUE VALUE TOLERANCE DATA TABLE UNLESS OTHERWISE SPECIFIED. MM

.5

.3

.1 AS NOTED IN AS NOTED

` .030

` .015

` .005

` 1 DEG.

` 10%

X X.X X.XX X.XXX ANGLE TORQUE MATERIAL:

SILVER -

PERMANENT ADHESIVE COLOR:

SEE NOTE SAVANT SYSTEMS LLC PROPRIETARY & CONFIDENTIAL TITLE 45 PERSERVERANCE WAY HYANNIS, MA 02601 THIS DOCUMENT CONTAINS COMPANY PROPRIETARYINFORMATION AND IS NOT TO BE REPRODUCED OR DISTRIBUTED WITHOUT PRIOR AUTHORIZATION QO SEM MODULE, PON, PRODUCT LABEL SIZE B SCALE UNITS MM 1:1 DWG NO 083-1013-00 REV 01 SHEET 1 OF 1 M/N: GPM-QP2SEM-00 REV: XX S/N: XXXXXXXXXXXX UID: XXXXXXXXXXXXXXXX MADE IN CHINA 33.00mm 11.00mm REV 00 01 CREATOR ZWH UA ECO #

13280 13188 DATE 06JUNE22 20SEP22 DESCRIPTION INITIAL CREATION UPDATE FORMAT, ADD REGULATORY INFO 33.6 SMART ENERGY MONITOR GPM-C2SEM INDOOR USE ONLY MODULE INPUT: 120VAC 60Hz SIGNAL INPUT: 0.333VAC 60Hz 45.9

#18-24 AWG Min. 105C Cu ONLY E523609 HOME AUTOMATION EQUIPMENT IC: 10798A-HQC2SEM FCC ID: PUU-HQC2SEM CT CONNECTIONS 1 2

NOTES: UNLESS OTHERWISE SPECIFIED 1. USE 3-D SOURCE FOR FABRICATION. THIS DRAWING IS TO BE USED FOR PART INSPECTION AND CRITICAL DIMENSIONS THAT AFFECT FIT, FORM AND FUNCTION 2.MARK PART NUMBER, REV, DATE, MANUFACTURER ON:

A. BULK PACKAGING B. ON PRODUCT AS SHOWN 3. ADHESIVE 3M 467 4. COLOR: SILVER BACKGROUND WITH BLACK C TEXT 5. USE M/N PER P.O. SCREW TORQUE DATA SIZE/ITEM TORQUE VALUE TOLERANCE DATA TABLE UNLESS OTHERWISE SPECIFIED. MM

.5

.3

.1 AS NOTED IN AS NOTED

` .030

` .015

` .005

` 1 DEG.

` 10%

X X.X X.XX X.XXX ANGLE TORQUE MATERIAL:

SILVER -

PERMANENT ADHESIVE COLOR:

SEE NOTE SAVANT SYSTEMS LLC PROPRIETARY & CONFIDENTIAL TITLE 45 PERSERVERANCE WAY HYANNIS, MA 02601 THIS DOCUMENT CONTAINS COMPANY PROPRIETARYINFORMATION AND IS NOT TO BE REPRODUCED OR DISTRIBUTED WITHOUT PRIOR AUTHORIZATION CH SMART ENERGY MONITOR, PRODUCT LABEL SIZE B SCALE UNITS MM 1:1 DWG NO 083-1003-00 REV 01 SHEET 1 OF 1 M/N: GPM-C2SEM-00 REV: XX S/N: XXXXXXXXXXXX UID: XXXXXXXXXXXXXXXX MADE IN CHINA 33.00mm 11.00mm REV 00 01 CREATOR ZWH UA ECO #

13280 13188 DATE 18AUG22 20SEP22 DESCRIPTION INITIAL CREATION UPDATE FORMAT, ADD REGULATORY INFO 33.6 SMART ENERGY MONITOR GPM-CP2SEM INDOOR USE ONLY MODULE INPUT: 120VAC 60Hz SIGNAL INPUT: 0.333VAC 60Hz 45.9

#18-24 AWG Min. 105C Cu ONLY E523609 HOME AUTOMATION EQUIPMENT IC: 10798A-HQC2SEM FCC ID: PUU-HQC2SEM CT CONNECTIONS 1 2

NOTES: UNLESS OTHERWISE SPECIFIED 1. USE 3-D SOURCE FOR FABRICATION. THIS DRAWING IS TO BE USED FOR PART INSPECTION AND CRITICAL DIMENSIONS THAT AFFECT FIT, FORM AND FUNCTION 2.MARK PART NUMBER, REV, DATE, MANUFACTURER ON:

A. BULK PACKAGING B. ON PRODUCT AS SHOWN 3. ADHESIVE 3M 467 4. COLOR: SILVER BACKGROUND WITH BLACK C TEXT 5. USE M/N PER P.O. SCREW TORQUE DATA SIZE/ITEM TORQUE VALUE TOLERANCE DATA TABLE UNLESS OTHERWISE SPECIFIED. MM

.5

.3

.1 AS NOTED IN AS NOTED

` .030

` .015

` .005

` 1 DEG.

` 10%

X X.X X.XX X.XXX ANGLE TORQUE MATERIAL:

SILVER -

PERMANENT ADHESIVE COLOR:

SEE NOTE SAVANT SYSTEMS LLC PROPRIETARY & CONFIDENTIAL TITLE 45 PERSERVERANCE WAY HYANNIS, MA 02601 THIS DOCUMENT CONTAINS COMPANY PROPRIETARYINFORMATION AND IS NOT TO BE REPRODUCED OR DISTRIBUTED WITHOUT PRIOR AUTHORIZATION CH SEM MODULE, PON, PRODUCT LABEL SIZE B SCALE UNITS MM 1:1 DWG NO 083-1014-00 REV 01 SHEET 1 OF 1 M/N: GPM-CP2SEM-00 REV: XX S/N: XXXXXXXXXXXX UID: XXXXXXXXXXXXXXXX MADE IN CHINA 33.00mm 11.00mm

Savant Technologies LLC, dba GE Lighting, a Savant company 1975 Noble Road, East Cleveland, OH 44112 USA Authority to Act as Agent Date: January 3, 2022 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

______ Audix Technology (Shanghai) Co., Ltd. 1______ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: _____December 29, 2022_____ By:

Title:

On behalf of:

_ Savant Technologies LLC, dba GE Lighting, a Savant company_________________________ Telephone:

____Paul Smith____________________

(Print name) _Systems Engineer Safety & Regulatory_________________________ __ ________________________ ___216 266 2189________________________

(Company Name)

(Signature2) 1 - If a group entity is designated as the authorized agent, the letter of authorization must identify those individuals within the group who are authorized to take action on the application; or alternatively a statement must be provided indicating that as the authorized agent, any individual within the group entity is authorized to act on behalf of the applicant / grantee and take action on the application. See https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=33316 . 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 041521-14

Savant Technologies LLC, dba GE Lighting, a Savant company 1975 Noble Road, East Cleveland, OH 44112 USA Request for Confidentiality Date: September 30, 2022 Subject: Confidentiality Request for: ______PUU-HQC2SEM______ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 12.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent *1 Permanent Permanent Permanent Permanent Permanent *3 Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual ______Savant Technologies LLC, dba GE Lighting, a Savant company______ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___0 2___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By:

(Signature/Title3) ___Paul Smith_____________________

(Print name) Systems Engineer Safety & Regulatory 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Please refer to https://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 041521-14

Savant Technologies LLC, dba GE Lighting, a Savant company 1975 Noble Road, East Cleveland, OH 44112 USA Date: September 30, 2022 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 Attn: Office of Engineering and Technology Ref:

FCC ID:PUU-HQC2SEM IC:10798A-HQC2SEM To whom it may concern:

Please be notified that we, the undersigned, Savant Technologies LLC, dba GE Lighting, a Savant company declare that the differences among the models are as following:

Information Product Name 1-INCH 2-CHANNEL POWER MONITOR MODULE, PIGTAIL QO 2-CHANNEL POWER MONITOR MODULE, PIGTAIL QO 2-CHANNEL POWER MONITOR MODULE, PON CH 2-CHANNEL POWER MONITOR MODULE, PIGTAIL CH 2-CHANNEL POWER MONITOR MODULE, PON Model No. GPM-H2SEM-00 GPM-Q2SEM-00 GPM-QP2SEM-00 GPM-C2SEM-00 GPM-CP2SEM-00 Difference 1. The N wire position is different, one (PON) is at the back of the module, another one (PIGTAIL) is at the bottom of the module with a wire. 2. The 1-INCH series, QO series, CH series just the appearance is different. The dimension of enclosure is different to match different companion device type. Savant Technologies LLC, dba GE Lighting, a Savant company 1975 Noble Road, East Cleveland, OH 44112 USA 1-INCH series Note: E = input L; D = input N The location of input (L,N) was different, the dimension of enclosure is different to match different companion device type. QO series CH series Sincerely, By:

Paul Smith

(Signature)

(Print name) Title:

Systems Engineer Safety & Regulatory