FCC ID: 2AJAC-CLRC1DW ClareOne Door/Window Sensor

ClareOne Door/Window Sensor Installation Sheet Installation The door/window sensor can be installed using the provided adhesive or screws. Mounting orientation The sensor and magnet should be placed near the top of the door with the sensor attached to the unmoving part of the closure. For example, attach the main body of the sensor to the door frame, not the door. We recommend that the sensor is placed in the top corner of the opening side of the door, see Figure 1. Figure 1: Sensor orientation The sensor and magnet each have a slightly engraved line. This line denotes where the sensors align to function properly. If the sensor and magnet, when together/closed, do not line up, the sensor will not report correctly. See Figure 2, on page 2. Part number:

ClareOne Door/Window Sensor, White (CLR-C1-DW-W) ClareOne Door/Window Sensor, Brown (CLR-C1-DW-B) Description The ClareOne Door/Window Sensor is a magnetic sensor device designed to fit seamlessly alongside a door frame or window frame. When the door or window is opened, the magnetic contact is disrupted, and then the sensor transmits an alarm notification to the ClareOne panel. Important safety instructions Before you install this sensor, be sure to:

Read, keep, and follow all instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat. Do not expose the device to water. When there is a low battery, replace with a compatible lithium ion battery. 25AUG23 Snap One, LLC. 1 / 5 DOC ID 1897 Rev 03 Figure 2: Sensor alignment 3.1.c (Optional) Mark the screw hole locations, then using a power drill, drill holes and install the 2 provided wall anchors. 3.1.d Remove the adhesive film cover. To install the door/window sensor:

1. Select the desired position for the sensor and magnet. Notes The sensor and magnet must be within 0.25 inches of each other on final installation. See Table 1, on page 4 for different gap ranges on metallic and non-metallic mounting surfaces. Verify that the sensor and magnet are aligned correctly. See Figure 2, on page 2. 2. Remove the sensors battery pull tab. 3.1.e Place the back plate against the door frame/window frame, making sure that the orientation is correct for the desired position. Note: Once the adhesive is secure, the sensor cannot be moved. 3.1.f Insert the first screw into the non-breakaway screw hole, and then use a screwdriver to partially secure the screw in the wall. Do not fully insert the screw until the second screw has secured the sensors position. 3. Adhere the sensor to the wall using the provided screws or adhesive. 3.1.g Insert a second screw into the breakaway screw hole, and then partially secure in the wall. Note: We recommend using the provided screws for installation. This method is more secure than using adhesive alone. Sensor screws 3.1.a Locate the bottom of the sensor (the slotted short end). 3.1.b Turn the sensor over, then gently slide a fingernail/fingertip into the slot pushing the sensors back plate up and away from the sensor body. 3.1.h Observe the sensor position. When satisfied with the position, use a screwdriver to fully secure each screw in the wall. 3.1.i Press the front of the sensor against the base until there is an audible snap. 25AUG23 Snap One, LLC. 2 / 5 DOC ID 1897 Rev 03 Sensor adhesive 3.2.a Select the desired position for the sensor. 3.2.b Peel one side of the adhesive tape, and then press the tape firmly against the sensor. Note: Once the adhesive is secure, the sensor cannot be moved. 3.2.c Peel the other side of the adhesive, and then press the sensor against the wall. 4. Line the magnet up with the sensor, verifying that they align properly, and then adhere the sensor to the wall using the provided screws or adhesive. Magnet screws 4.1.a Locate the bottom of the magnet (the slotted short end). 4.1.b Turn the magnet over, and then gently slide a fingernail/fingertip into the slot pushing the magnets back plate up and away from the magnet body. 4.1.c (Optional) Mark the screw hole locations, then using a power drill, drill holes and install the 2 provided wall anchors. 4.1.d Remove the adhesives film cover, and then place the back plate against the door/window, making sure that the orientation and alignment are correct for the desired position. Note: Once the adhesive is secure, the magnet cannot be moved. 4.1.e Insert the first screw into a screw hole, then use a screwdriver to partially secure the screw in the wall. Do not fully insert the screw until the second screw has secured the magnet position. 4.1.f Insert a second screw into the remaining hole, and then partially secure it in the wall. 4.1.g Observe the magnet position. When satisfied with the position, use a screwdriver to fully secure each screw in the wall. 4.1.h Press the front of the magnet against the base, until there is an audible snap. Magnet adhesive 4.2.a Select the desired position for the magnet. 4.2.b Peel one side of the adhesive tape, and then press the tape firmly against the magnet. Note: Once the adhesive is secure, the magnet cannot be moved. 4.2.c Peel the other side of the adhesive, and then press the magnet against the wall. 5. Add the sensor to the panel. See Sensor Management, ClareOne User Guide. 25AUG23 Snap One, LLC. 3 / 5 DOC ID 1897 Rev 03 6. Once added, test the sensor. Look at the ClareOne panel, and then open the door/window. Notice that the added sensor displays faulted. Note: Testing all sensors with the alarm monitoring station is strongly advised. Table 1: Sensor and magnet gap range Non-metallic surface Supports Metallic surface Open Close Direction Open Close 4. Press and hold the tab away from the circuit board, and 31 mm 29 mm 34 mm 31 mm 35 mm 31 mm X Y Z 30 mm 25 mm 36 mm 35 mm 45 mm 40 mm Battery replacement The ClareOne Door/Window Sensor requires a CR2032 battery. Once the battery is low, the panel displays a low battery icon next to the sensor in the devices list. The battery must be replaced within 7 days of the first low battery notification. If the battery is not replaced within 7 days, the sensor may not function properly. WARNING: If an incompatible replacement battery is used, or the battery is installed incorrectly explosion or damages may occur. AVERTISSEMENT: Si une batterie de remplacement incompatible est utilise ou si la batterie est installe de manire incorrecte, une explosion ou des dommages peuvent survenir. To replace the battery:

Note: Verify that the panel is not armed before changing the battery. 1. Locate the bottom of the sensor (the slotted short end). 2. Gently slide a fingernail/fingertip into the slot and pull the sensor cover out and away from the sensors base. 3. The sensor containing the battery and circuit board is no longer attached to the door/window. Locate the tab holding the circuit board in the sensor. then turn the sensor over. The circuit board comes free from the sensor shell. 5. Use a fingernail/fingertip to push the battery out of the casing, noting the polarity of the battery. 6. Slide a new CR2032 battery into the battery casing, making sure that the polarity is correct. 7. Press the circuit board back into the sensor casing, sliding it under the clips, until secure. There will be an audible snap. 8. Press the sensor back onto the base. 9. Test the sensor. Specifications Compatible panel ClareOne Transmitter frequency 433MHz TX Encrypted Yes Transmitted indications Tamper Low battery Battery type CR2032 (220mAh) Battery life Screw size Adhesive 5 years M3 16 mm 3M 4930 Sensor dimensions

(W H D) 1.69 2.52 .51 in.

(43 64.05 13 mm) Operating environment Temperature Relative humidity 32 to 122.6F (0 to 50C) 85% max Water-resistant No 25AUG23 Snap One, LLC. 4 / 5 DOC ID 1897 Rev 03 Regulatory information Manufacturer Snap One, LLC. North American standards ETL listed to: UL 634, ULC ORD634 FCC compliance FCC ID: 2AJAC-CLRC1DW This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-

located or operating in conjunction with any other antenna or transmitter. IC Compliance IC ID: 7848A-CLRC1DW ISED compliance statement:

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation. Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. L'metteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR d'innovation. Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

L'appareil doit accepter tout brouillage 2. radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme aux limites d'exposition aux radiations IC CNR-102 tablies pour un environnement non contrl. Cet metteur ne doit pas tre colocalis ou fonctionner en conjonction avec une autre antenne ou un autre metteur. Warranty information Snap One offers a two (2) year limited warranty on original Clare components, from the date of shipment from Snap One. To view complete limited warranty details, including limitations and exclusions, www.snapone.com/legal. Scan the code to view product warranty details. Contact information www.clarecontrols.com Integrator/Dealer Support: 866-424-4489 claresupport@clarecontrols.com Homeowners should contact their professional installer for assistance. 25AUG23 Snap One, LLC. 5 / 5 DOC ID 1897 Rev 03

A. LABEL LOCATION EXHIBIT Due to the size, appearance, shape and shell material of the product, the warning words related to the requirements of FCC PART 15.19 cannot be placed on the product main body, thus the content of the warning words will be described in the instruction manual. The warning words of FCC PART 15.19:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Size: L*W*H 63.3mm*33.4mm*12.4mm LABEL LOCATION EXHIBIT

*Please return a signed copy to the TCB Manager*

By signing this document, I acknowledge I have read and understand the above information Date:

07/19/2023 Signature:

Print Name:

Roger Midgley 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com Rev:0.0

Applicant Legal Business Name Address Grantee Code FCC ID Authorized Contact Name Contact Email Contact Phone Snap One, LLC 1800 Continental Blvd Suit 200-300 Charlotte, North Carolina 28273 USA 2AJAC 2AJAC-CLRC1DW Roger Midgley roger.midgley@snapone.com 385-449-1193 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

a) b) c) d) e) In accordance with 47CFR2.91(d), all of the statements herein and the exhibits attached are true and correct to the best of my knowledge and belief. In accepting a Grant of Equipment Authorization issues by TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

(1) Labeling the equipment with the exact FCC ID as specified in this application,

(2) Compliance statement labeling pursuant to the applicable rules,

(3) Compliance of the equipment with the applicable technical rules, If the Applicant is not the actual manufacture of the equipment, appropriate arrangements have been made with the manufacture to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. In accordance with 47 CFR 2.909 AND kdb394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agrees to abide their responsibilities as specified under 47 CFR 2.909 and KDB364321. In accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1) The Applicant understands, accepts and agrees that a sample may be requested for surveillance testing.

(2) The Applicant shall make provisions to always have production sample available upon request by SGS, FCC and/or ISED.

(3) The Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) Neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. g) The Applicant has read , understood, accepts to abide by the SGS North America, Inc. (TCB) term and conditions. Link to CFRs: Rules & Regulations for Title 47 | Federal Communications Commission (fcc.gov) Link to KDBs: OET Knowledge Database (KDB) (fcc.gov) Link to RSP-100: RSP-100 Certification of Radio Apparatus and Broadcasting Equipment (canada.ca) Link to the Covered List: List of Equipment and Services Covered By Section 2 of The Secure Networks Act | Federal Communications Commission (fcc.gov) Applicant Signature:

Date:

07/19/2023 Print Name:

Title:

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Roger Midgley Principal Compliance Engineer 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com

SYBER SENSE IOT COMPANY LIMITED Federal Communications Commission, Date:2023-07-11 Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch CHANG IN IDENTIFICATION OF EQUIPMENT We, SYBER SENSE [OT COMPANY LIMITED, declare on our sole responsibility that Snap One, LLC may apply Change in FCC Identifier as established in 47CFR 2.933(b) for currently approved devices listed below. 1. The original identification is FCC ID: 2AVDCXPDO3-E-1433 2. The original grant date is 09/13/2021 Snap One, LLC will establish a new FCC ID: 2A3AC-CLRCLDW Regards, cerely, Print Name: Simon Lee Title:CEO Signature:

On behalf of Company: SYBER SENSE |OT COMPANY LiMiTED Telephone: 90276048 E-mail: simon.lee@d-3.com.hk

Federal Communications Commission, Date: 2023-07-19 Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch CHANG IN IDENTIFICATION OF EQUIPMENT We, Snap One, LLC , request to apply for a new FCC ID as established in 47CFR 2.933(b) for a currently approved device. This application will establish a new FCC ID: 2AJAC-CLRC1DW. Per 2.933(b) 1. The original identification is FCC ID: 2AVDCXPD03-E-1433 2. The original grant date is 09/13/2021 3. The equipment is electrically identical. There is no change in design, circuitry or construction. 4. The original test results are applicable and representative of this changed device. 5. Exterior photographs are included in this application. External photos with label location and type label sample drawing are electronically submitted as attachments. Sincerely, Print Name: Roger Midgley Title: Principal Compliance Engineer Signature:

On behalf of Company: Snap One, LLC Telephone: 385-449-1193 E-mail: roger.midgley@snapone.com 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com

TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AJAC-CLRC1DW To whom it may concern:

Date: 2023-07-19 We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Snap One, LLC This authorization is valid until further written notice from the applicant. Print Name: Roger Midgley Title: Principal Compliance Engineer Signature:

On behalf of Company: Snap One, LLC Telephone: 385-449-1193 E-mail: roger.midgley@snapone.com 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com

UNITED STATES DESIGNATED AGENT LETTER Date: 2023-07-19 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant Company Name: Snap One, LLC U.S. designated agent Company Name:

Snap One, LLC Grantee Code:

Contact Name:

Address:

Telephone:

Email:

2AJAC Roger Midgley 1800 Continental Blvd Suite 200-300 Charlotte, North Carolina 28273 USA 8015233187 roger.midgley@snapone.com FRN:

Contact Name:

Address:

Telephone:

Email:

0010808202 Roger Midgley 1800 Continental Blvd Suite 200-300 Charlotte, North Carolina 28273 USA 8015233187 roger.midgley@snapone.com Applicable Equipment: FCC ID: 2AJAC-CLRC1DW ATTN: Director of Certification:

We, Snap One, LLC understand and acknowledge the applicants consent and the designated agents obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, Snap One, LLC acknowledge the applicants acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant U.S. designated agent Name (Printed): Roger Midgley Name (Printed): Roger Midgley Title: Principal Compliance Engineer Title: Principal Compliance Engineer Signature:

Signature:

1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com