FCC ID: 2AJAC-CORELITE Digital Transmission Radio

Warnings Front view Control4 CORE Lite Controller Installation Guide Caution! To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture. AVERTISSEMENT ! Pour rduire le risque de choc lectrique, nexposez pas cet appareil la pluie ou lhumidit. Caution! In an over-current condition on USB, the software disables the output. If the attached USB device does not appear to power on, remove the USB device from the controller. AVERTISSEMENT ! Dans une condition de surintensit sur USB ou sortie de contact le logiciel dsactive sortie. Si le priphrique USB ou le capteur de contact connect ne semble pas sallumer, retirez le priphrique du contrleur. A CB D E A Activity LEDThe Activity LED shows when the controller is streaming audio. B C Caution LEDThis LED shows solid red, then blinks blue during the boot process. IR windowIR receiver for learning IR codes. Note: The Caution LED blinks orange during the factory restore process. See Reset to factory settings in this document. D Link LEDThe LED indicates that the controller has been identified in a Control4 project and is communicating with Director. E Power LEDThe blue LED indicates that AC power is present. The controller turns on immediately after power is applied to it. Specifications Video out Video Audio out Inputs / Outputs 1 video out1 HDMI HDMI 2.0a; 3840x2160 @ 60Hz; HDCP 2.2 and HDCP 1.4 1 audio outHDMI Back view Audio playback formats AAC, AIFF, ALAC, FLAC, M4A, MP2, MP3, MP4/M4A, Ogg Vorbis, PCM, WAV, WMA High-resolution audio playback Up to 192 kHz / 24 bit Network 1 10/100/1000BaseT compatible network port Optional Dual-Band Wi-Fi USB Adapter

(2.4 GHz, 5 Ghz, 802.11ac/b/g/n/a) 802.15.4 Internal antenna 1 USB 2.0 port500mA Control 3 IR out5V 27mA max output 1 IR receiverfront, 20-60 KHz 1 serial out (shared with IR out 1) Power 100-240 VAC, 60/50Hz Max: 18W, 61 BTUs/hour Idle: 12W, 41 BTUs/hour Other A B C D E F A Power portAC power connector for an IEC 60320-C5 power cord. B IR OUT/SERIAL3.5 mm jacks for up to three IR emitters or for a combination of IR emitters and serial devices. Port 1 can be configured independently for serial control

(for controlling receivers or disc changers) or for IR control. See Connecting the IR ports/serial ports in this document for more information. C USBOne port for an external USB drive (such as a USB stick formatted FAT32). See Setting up external storage devices in this document. D HDMI OUTAn HDMI port to display navigation menus. Also an audio out over HDMI. E ID button and RESETID button is pressed to identify the device in Composer Pro. The ID button on the CORE Lite is also an LED that displays feedback useful during a factory restore. The RESET pinhole is used to reset or factory restore the controller. F ETHERNETRJ-45 jack for a 10/100/1000BaseT Ethernet connection. Installation instructions To install the controller:

Connecting the IR ports/serial ports (optional) The controller provides three IR ports, and port 1 can be reconfigured independently for serial communication. If not used for serial, they can be used for IR. Connect a serial device to the controller using the Control4 3.5 mm-to-DB9 Serial Cable (C4-CBL3.5-

DB9B, sold separately). 1 The serial ports support baud rates between 1200 to 115200 baud for odd and even parity. The serial ports do not support hardware flow control. 2 See Knowledgebase article #268 (ctrl4.co/contr-serial-pinout) for pinout diagrams. 3 To configure a port for serial or IR, make the appropriate connections in your project using Composer Pro. See the Composer Pro User Guide for details. Note: The serial ports can be configured as straight-through or null with Composer Pro. Serial ports by default are configured straight-through and can be changed in Composer by selecting Null Modem Enabled (SERIAL 1). Setting up IR emitters Your system may contain third-party products that are controlled through IR commands. 1 Connect one of the included IR emitters to an IR OUT port on the controller. 2 Place the stick-on emitter end onto the IR receiver on the Blu-ray player, TV, or other target device to emit IR signals from the controller to the target device. Setting up external storage devices (optional) You can store and access media from an external storage device, for example, a network hard drive or USB memory device, by connecting the USB drive to the USB port and configuring or scanning the media in Composer Pro. Note: We support only externally powered USB drives or solid state USB sticks. Self-powered USB drives are not supported. Note: When using USB storage devices on an CORE Lite controller, you can use only one partition with a 2 TB maximum size. This limitation also applies to the USB storage on other controllers. Composer Pro driver information Use Auto Discovery and SDDP to add the driver to the Composer project. See the Composer Pro User Guide (ctrl4.co/cpro-ug) for details. OvrC setup and configuration OvrC gives you remote device management, real-time notifications, and intuitive customer management, right from your computer or mobile device. Setup is plug-and-play, with no port forwarding or DDNS address required. Operating temperature 32F ~ 104F (0C ~ 40C) Storage temperature 4F ~ 158F (-20C ~ 70C) Dimensions (H W D) 1.16 7.67 5.2" (29.5 195 132 mm) Weight Shipping weight 1.5 lb (0.68 kg) 2.3 lb (1.04 kg) Additional resources The following resources are available for more support. Control4 CORE series help and information: ctrl4.co/core Snap One Tech Community and Knowledgebase: tech.control4.com Control4 Technical Support: ctrl4.co/techsupport Control4 website: www.control4.com 1 Ensure that the home network is in place before starting system setup. An Ethernet To add this device to your OvrC account:

1 Connect CORE Lite controller to the Internet. 2 Navigate to OvrC (www.ovrc.com) and log in to your account. 3 Add the device (MAC address and Service Tag numbers needed for authentication). connection to the local network is required for setup. The controller requires a network connection to use all of the features as designed. After initial configuration, Ethernet (recommended) or Wi-Fi (with an optional adapter) can be used to connect the controller to web-based media databases, communicate with other IP devices in the home, and access Control4 system updates. 2 Mount the controller near the local devices you need to control. The controller can be hidden behind a TV, mounted on a wall, installed in a rack, or placed on a shelf. The CORE 1/Lite Rack Mount Kit is sold separately and is designed for easy installation of up to two CORE 1/Lite controllers side by side in a rack. The CORE 1/

Lite Wall-Mount Bracket is sold separately and designed for easy installation of the CORE Lite controller behind a TV or on the wall. 3 Connect the controller to the network. EthernetTo connect using an Ethernet connection, connect the network cable into the controllers RJ-45 port (labeled ETHERNET) and into the network port on the wall or at the network switch. Wi-FiTo connect using Wi-Fi, first connect the unit to Ethernet, connect the Wi-Fi adapter to the USB port, and then use Composer Pro System Manager to reconfigure the unit for Wi-Fi. 4 Connect system devices. Attach IR and serial devices as described in Connecting the IR ports/serial ports and Setting up IR emitters. 5 Set up any external storage devices as described in Setting up external storage devices in this document. 6 Connect the power cord to the controllers power port and then into an electrical outlet. Supported model C4-CORE-LITE CONTROL4 SINGLE ROOM HUB & CONTROLLER Introduction Designed for an exceptional family room entertainment experience, the Control4 CORE Lite Controller does more than automate the gear around your TV; it is the ideal smart home starter system with entertainment built in. The CORE Lite delivers a beautiful, intuitive, and responsive on-screen user interface with the ability to create and enhance the entertainment experience for any TV in the house. The CORE Lite can orchestrate a wide range of entertainment devices including Blu-ray players, satellite or cable boxes, game consoles, TVs, and virtually any product with infrared (IR) or serial (RS-232) control. It also features IP control for Apple TV, Roku, televisions, AVRs, or other network-connected devices, as well as secure wireless Zigbee control for lights, thermostats, smart locks, and more. For entertainment, the CORE Lite also includes a built-in music server that allows you to listen to your own music library, stream from a variety of leading music services, or from your AirPlay-enabled devices using Control4 ShairBridge technology. Ethernet Wi-Fi Zigbee Pro Zigbee antenna USB port IR out IR capture Serial out Box contents The following items are included in the CORE Lite controller box:

Power requirements Power consumption CORE Lite controller AC power cord IR emitters (2) Rubber feet (2, pre-installed) Accessories available for purchase CORE 1 Wall-Mount Bracket (C4-CORE1-WM) Control4 1U Rack-Mount Kit, Single/Dual Controller (C4-CORE1-RMK) Control4 Dual-Band Wi-Fi USB Adapter (C4-USBWIFI OR C4-USBWIFI-1) Control4 3.5 mm to DB9 Serial Cable (C4-CBL3.5-DB9B) Requirements and specifications Note: We recommend using Ethernet instead of Wi-Fi for the best network connectivity. Note: The Ethernet or Wi-Fi network should be installed before starting the CORE Lite controller installation. Note: The CORE Lite requires OS 3.3.3 or newer. Composer Pro software is required to configure this device. See the Composer Pro User Guide (ctrl4.co/cpro-ug) for details. Troubleshooting Reset to factory settings More help For the latest version of this document and to view additional materials, open the URL below or scan the QR code on a device that can view PDFs. Caution! The factory restore process will remove the Composer project. MOST RECENT VERSION MORE INFO ON CORE CONTROLLERS ctrl4.co/corelite-ig ctrl4.co/core Legal, Warranty, and Regulatory/Safety information Visit snapone.com/legal for details. To restore the controller to the factory default image:

1 Insert one end of a paper clip into the small hole on the back of the controller labeled RESET. 2 Press and hold the RESET button. The controller resets and the ID button changes to solid red. 3 Hold the button until the ID flashes double orange. This should take five to seven seconds. The ID button flashes orange while the factory restore is running. When complete, the ID button turns off and the device power cycles one more time to complete the factory restore process. Note: During the reset process, the ID button provides the same feedback as the Caution LED on the front of the controller. Power cycle the controller 1 Press and hold the ID button for five seconds. The controller turns off and back on. Reset the network settings To reset the controller network settings to the default:

1 Disconnect power to the controller. 2 While pressing and holding the ID button on the back of the controller, power on the controller. 3 Hold the ID button until ID button turns solid orange and the Link and Power LEDs are solid blue, and then immediately release the button. Note: During the reset process, the ID button provides the same feedback as the Caution LED on the front of the controller. LED status information Activity Caution Link Power Flashing LED Solid LED Just powered on Boot started Boot complete Network reset check Factory restore underway Connected to Director Playing audio Updating Update error No IP address Copyright 2023, Snap One, LLC. All rights reserved. Snap One and its respective logos are registered trademarks or trademarks of Snap One, LLC (formerly known as Wirepath Home Systems, LLC), in the United States and/or other countries. 4Store, 4Sight, Control4, Control4 My Home, SnapAV, Mockupancy, NEEO, OvrC, Wirepath, and Wirepath ONE are also registered trademarks or trademarks of Snap One, LLC. Other names and brands may be claimed as the property of their respective owners. Snap One makes no claim that the information contained herein covers all installation scenarios and contingencies, or product use risks. Information within this specification subject to change without notice. A 200-00954-A 2023-03-07 DH control4.com | 888.400.4070

Regulatory Compliance & Safety Information for Model C4-CORE-LITE Electrical Safety Advisory Scurit lectrique consultatif Important Safety Instructions Consignes de scurit importantes Read the safety instructions before using this product. Lisez les consignes de scurit avant d'utiliser ce produit. 1. Read these instructions. Lisez ces instructions. 2. Keep these instructions. Conservez ces instructions. 3. Heed all warnings. Respectez tous les avertissements. 4. Follow all instructions. Suivez toutes les instructions. 5. Do not use this apparatus near water. Ne pas utiliser cet appareil prs de l'eau. 6. Clean only with dry cloth. Nettoyez-le uniquement avec un chiffon sec. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Ne pas bloquer les ouvertures de ventilation. Installer conformment aux instructions du fabricant. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Ne pas installer prs de sources de chaleur telles que des radiateurs, registres de chaleur, poles, ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur. 9. Rack Mount Instruction A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer. B) Reduced Air Flow- Installation of the equipment in a rack should be such that the amount of airflow required for the safe operation of the equipment is not compromised. C) Mechanical Loading- Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading. D) Circuit Overloading 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com

- Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. E) Reliable Earthing

- Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit

(e.g. use of power strips). Instructions de montage en rack A) Ambiance de fonctionnement leve

- En cas d'installation dans un rack ferm ou plusieurs units, la temprature ambiante de fonctionnement de l'environnement du rack peut tre suprieure la temprature ambiante de la pice. Par consquent, il convient d'envisager d'installer l'quipement dans un environnement compatible avec la temprature ambiante maximale (Tma) spcifie par le fabricant. B) Dbit d'air rduit

- L'installation de l'quipement dans un rack doit tre telle que la quantit d'air ncessaire au fonctionnement sr de l'quipement ne soit pas compromise. C) Chargement mcanique

- Le montage de l'quipement dans le rack doit tre tel qu'une condition dangereuse ne soit pas atteinte en raison d'une charge mcanique ingale. D) Surcharge du circuit

- Il faut tenir compte de la connexion de l'quipement au circuit d'alimentation et de l'effet que la surcharge des circuits pourrait avoir sur la protection contre les surintensits et le cblage d'alimentation. Une considration approprie des caractristiques nominales de l'quipement doit tre utilise pour rpondre cette proccupation. E) Mise la terre fiable

- Une mise la terre fiable des quipements monts en rack doit tre maintenue. Une 10. Wall Mounting Important! Do not mount over 6 ft high (2 m). Important! Mount the bracket with the tabs on the bottom (opening to the top) so the controller will not fall out of the bracket. Montage mural Important ! Ne pas monter plus de 6 pieds (2 m) de haut. Important! Montez le support avec les languettes en bas (ouverture vers le haut) afin que le contrleur ne tombe pas du support. 11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Utilisez uniquement avec le chariot, le socle, le trpied, le support ou la table spcifis par le fabricant ou vendu avec l'appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous dplacez l'ensemble chariot / appareil pour viter des blessures dues au renversement. 12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com Confiez toutes les rparations un personnel qualifi. Une rparation est ncessaire lorsque l'appareil a t endommag de quelque faon que ce soit le cordon d'alimentation ou la fiche est endommag, du liquide a t renvers ou si des objets sont tombs dans l'appareil, l'appareil a t expos la pluie ou l'humidit, ne fonctionne pas normalement, ou s'il est tomb. 13. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Protgez le cordon d'alimentation ne soit pitin ou pinc, en particulier au niveau des fiches, des prises et au point o il sort de l'appareil. 14. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. Unplug this apparatus during lightning storms or when unused for long periods of time. Cet quipement utilise la puissance AC qui peuvent tre soumis des surtensions lectriques, la foudre gnralement transitoires qui sont trs destructives envers les quipements terminaux connects des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causs par les surtensions lectriques ou transitoires de foudre. Pour rduire le risque de cet quipement devient endommag, il est suggr que le client envisager l'installation d'un limiteur de surtension. Dbranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilis pendant de longues priodes de temps. 15. To completely disconnect unit power from the AC mains, remove the power cord from the appliance coupler and/or turn off the circuit breaker. To reconnect power, turn on the circuit breaker following all safety instructions and guidelines. The circuit breaker shall remain readily accessible. Pour dbrancher compltement l'alimentation secteur du rseau secteur, retirez le cordon d'alimentation du coupleur de l'appareil et / ou teignez le disjoncteur. Pour reconnecter l'alimentation, allumez le disjoncteur en suivant toutes les consignes et consignes de scurit. Le disjoncteur doit tre facilement accessible. 16. This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. Ce produit repose sur l'installation des btiments pour les courts-circuits (surintensit) de protection. Assurez-vous que le dispositif de protection est assigne ne dpassant pas:

20A. 17. WARNING Power Sources, Grounding, Polarization This product requires a properly grounded outlet for safety. This plug is designed to be inserted into a NEMA 5-15 (three-prong grounded) outlet only. Do not force the plug into an outlet that is not designed to accept it. Never dismantle the plug or alter the power cord, and do not attempt to defeat the grounding feature by using a 3-to-2 prong adapter. If you have a question about grounding, consult your local power company or qualified electrician. If a rooftop device such as a satellite dish connect to the product, ensure that the devices wires are also properly grounded. The bonding point can be used to provide a common ground to other equipment. This bonding point can accommodate minimum 12 AWG wire and should be connected using 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com the required hardware specified by the other bonding point. Please use termination for your equipment in accordance with the applicable local agency requirements. AVERTISSEMENT - Sources d'alimentation, mise la terre, polarisation Ce produit ncessite une prise correctement mise la terre pour des raisons de scurit. Cette fiche est conue pour tre insre dans une prise NEMA 5-15 (trois broches mise la terre) uniquement. Ne forcez pas la fiche dans une prise qui n'est pas conue pour l'accepter. Ne dmontez jamais la fiche ou ne modifiez pas le cordon d'alimentation, et n'essayez pas de dsactiver la fonction de mise la terre en utilisant un adaptateur 3 2 broches. Si vous avez une question sur la mise la terre, consultez votre compagnie d'lectricit locale ou un lectricien qualifi. Si un appareil sur le toit tel qu'une antenne parabolique se connecte au produit, assurez-

vous que les fils des appareils sont galement correctement mis la terre. Le point de liaison peut tre utilis pour fournir une masse commune d'autres quipements. Ce point de connexion peut accueillir un fil de 12 AWG minimum et doit tre connect l'aide du matriel requis spcifi par l'autre point de connexion. Veuillez utiliser une terminaison pour votre quipement conformment aux exigences des agences locales applicables. 18. Notice For indoor use only, Internal components are not sealed from the environment. The device can only be used in a fixed location such as a telecommunication center, or a dedicated computer room. When you install the device, ensure that the protective earthing connection of the socket-outlet is verified by a skilled person. Suitable for installation in information technology rooms in accordance with Article 645 of the National Electrical Code and NFP 75. Avis Pour une utilisation en intrieur uniquement, les composants internes ne sont pas scells de l'environnement. L'appareil ne peut tre utilis que dans un lieu fixe tel qu'un centre de tlcommunication, ou une salle informatique ddie. Lors de l'installation de l'appareil, assurez-vous que la mise la terre de protection de la prise de courant est vrifie par une personne qualifie. Convient pour une installation dans des salles informatiques conformment l'article 645 du Code national de l'lectricit et NFP 75. 19. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers, and microwave ovens if placed in close proximity. Ce produit peut interfrer avec des appareils lectriques tels que les magntophones, tlviseurs, radios, ordinateurs et fours micro-ondes si placs proximit. 20. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. N'introduisez jamais d'objets d'aucune sorte dans ce produit travers les fentes du botier car ils pourraient toucher des points de tension dangereux ou court-circuiter des pices qui pourraient entraner un incendie ou un choc lectrique. 21. WARNING No user serviceable parts inside. If the product is not operating properly, do not remove any part of the unit (cover, etc.) for repair. Unplug the unit and consult the warranty section of the owners manual. AVERTISSEMENT Aucune pice rparable par l'utilisateur l'intrieur. Si le produit ne fonctionne pas correctement, ne retirez aucune pice de l'appareil (couvercle, etc.) pour rparation. Dbranchez l'appareil et consultez la section de garantie du manuel du propritaire. 22. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines. Do not 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above 54 C or 130 F. ATTENTION: Comme avec toutes les batteries, il ya un risque d'explosion ou de blessure si la batterie est remplace par un type incorrect. liminez les batteries usages selon les instructions du fabricant de la batterie et applicables des directives environnementales. Ne pas ouvrir, percer ou incinrer la batterie, ou de l'exposer des matriaux conducteurs, de l'humidit, du liquide, un incendie ou une temprature suprieure 54 C ou 130 F. 23. PoE considered a Network Environment 0 per IEC TR62101, and thus the interconnected ITE circuits may be considered ES1. The installation instructions clearly state that the ITE is to be connected only to PoE networks without routing to the outside plant. PoE considr comme un environnement de rseau 0 selon IEC TR62101 et, par consquent, les circuits ITE interconnects peuvent tre considrs comme ES1. Les instructions d'installation indiquent clairement que l'ITE doit tre connect uniquement aux rseaux PoE sans acheminement vers l'installation externe. 24. CAUTION: The Optical Transceiver used with this product should use UL listed, and Rated Laser Class I, 3.3 Vdc. ATTENTION: L'metteur-rcepteur optique utilis avec ce produit doit utiliser la liste UL et la classe de laser nominale I, 3,3 Vcc. The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product L'clair et la flche dans le triangle est un signe d'alerte pour vous avertir d'une tension dangereuse l'intrieur du produit Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Attention: Pour rduire le risque de choc lectrique, ne pas retirer le couvercle

(ou l'arrire). Aucune pice rparable par l'utilisateur. Confiez l'entretien un personnel qualifi. The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. Le point d'exclamation dans un triangle est un signe d'avertissement vous signale des instructions importantes accompagnant le produit. See marking on bottom / back of product Voir le marquage sur les bas / dos du produit Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture AVERTISSEMENT! Pour rduire le risque de choc lectrique, n'exposez pas cet appareil la pluie ou l'humidit. Save these instructions Conservez ces instructions Compliance of this equipment is confirmed by the following label that is placed on the equipment:

Conformit de cet appareil est confirm par le symbole suivant qui est plac sur l'quipement:

1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com USA & Canada Compliance FCC Part 15, Subpart B & IC Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la section 15 des rgles. Son utilisation est soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles et (2) cet appareil doit accepter toutes les interfrences reues, y compris celles pouvant entraner un fonctionnement non souhait. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de lutilisateur pour actionner cet quipement. Innovation Science and Economic Development (ISED) Unintentional Emissions Interference Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference

(2) This device must accept any interference, including interference that may cause undesired operation of the device Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com

(1) Lappareil ne doit pas produire de brouillage;

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. FCC Part 15, Subpart C / RSS-247 Intentional Emissions Interference Statement Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment:

Notice: The term FCC ID: and IC: before the certification number signifies that FCC and Industry Canada technical specifications were met. FCC ID: 2AJAC-CORELITE IC: 7848A-CORELITE This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-247, Antenna Requirements. Do not use any antenna other than the one provided with the unit. FCC Partie 15, sous-partie C / RSS-247 Dclaration volontaire des missions interfrences Conformit de cet appareil est confirm par les chiffres de certification suivants qui sont placs sur l'quipement:

Avis: Le terme FCC ID:" et "IC:" devant le numro de certification signifie que les spcifications techniques de la FCC et d'Industrie Canada ont t respectes. FCC ID: 2AJAC-CORELITE IC: 7848A-CORELITE Cet quipement doit tre install par des professionnels qualifis ou entrepreneurs conformment aux normes FCC partie 15.203 & IC RSS-247, Exigences d'antenne. Ne pas utiliser une antenne autre que celui fourni avec l'appareil. Cet metteur ne doit pas tre localis ou fonctionner avec d'autres antennes ou transmetteurs. Les oprations dans la bande 5.15-5.25GHz sont limites l'utilisation l'intrieur seulement. RF Radiation Exposure Statement This equipment complies with FCC RF and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons. Dclaration d'exposition aux radiations RF Cet quipement est conforme aux limites d'exposition aux rayonnements RF et IC de la FCC dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 centimtres entre le radiateur et votre corps ou des personnes proches. Europe Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. The full text of the EU Declaration of Conformity (DoC) is available on the regulatory webpage:

1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com This product can be put into service in all of the EU member states, European Free Trade Association

(EFTA) and EU candidate countries without any restriction. CZ BG BE IE EE DE HR FR ES CY LT LV HU MT NL RO PT PL SE FI SK NO LI IS RS MK AL DK EL IT LU AT SI UK CH TR The frequency and maximum transmitted power in EU are listed as below:

2412 - 2472 MHz: 14.2 dBm United Kingdom (UK) Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. The full text of the UK Declaration of Conformity (DoC) is available on the regulatory webpage:

Recycling Snap One understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions. WEEE Compliance Snap One is committed to meeting all requirements of the Waste Electrical and Electronic Equipment (WEEE) directive (2012/19/EC). The WEEE directive requires the manufacturers of electrical and electronic equipment who sell in EU countries: (1) label their equipment to notify customers that it needs to be recycled, and (2) provide a way for their products to be 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com appropriately disposed of or recycled at the end of their product lifespan. For collection or recycling of Snap One products, please contact your local Snap One representative or dealer. Australia & New Zealand Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. About this Document Copyright 2022 Snap One All rights reserved. 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 05-11-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2AJAC-CORELITE Snap One (the applicant) (FRN: 0010808202) certifies that, as of the date of the filing of the application, Snap One will self-designated as a U.S. agent for service of process for the above referenced FCC ID. Snap One accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Snap One accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Sincerely yours, Printed Name: Roger Midgley Title: Principal Compliance Engineer Address: 1800 Continental Blvd., Suite 200-300, Charlotte NC 28273, USA Tel.: +1 385-449-1193 Email: Roger.Midgley@SnapOne.com

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 05-11-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AJAC-CORELITE Snap One (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Roger Midgley

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 05-11-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AJAC-CORELITE Snap One (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Roger Midgley

Date: May 11, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for confidentiality FCC ID: 2AJAC-CORELITE To whom it may concern:

Permanent confidentiality Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below:

Block Diagram Schematics Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Applicant Address

: Snap One, LLC

: 1800 Continental Blvd Suite 200-300 Charlotte, North Carolina 28273 USA Signature

_________________________________ Name and Job Title. E-mail Tel.

: Roger Midgley, Principle Compliance Engineer

: Roger.Midgley@SnapOne.com

: +18015233187 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com

Date: 2023/5/23 Federal Communications Commission 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter FCC ID: 2AJAC-CORELITE Product name: C4-CORE-LITE To whom it may concern:

We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization of model C4-CORE1 to the FCC Rules and Regulations. Compliance Test Services Address : 623 E 100 S, Salt Lake City, UT 84102

: Zach Hallows Name Job Title : Certification Specialist e-mail

: contact@compliancetestservices.com We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 862. This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Applicant Address

: Snap One, LLC

: 1800 Continental Blvd., Suite 200-300, Charlotte NC 28273, USA Signature

Name and Job Title. E-mail Tel. _________________________________

: Roger Midgley, Principal Compliance Engineer

: Roger.Midgley@SnapOne.com

: +18015233187 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com