FCC ID: 2AJAC-TSSA1200 The SA1 is a WiFi connected streaming audio amplifier

INTRODUCTION The Triad SA1 is a single-zone, high-resolution streaming amplifier and an easy way to add music into any room without the need to pull wire back to a central location. The Triad SA1 supports high-resolution audio playback, up to 192 kHz / 24 bit, with a built-in amplifier boasting an impressive 115 dB signal-to-noise ratio and 200 watts per channelenabling incredible sound in any room. Also included are equalizer, speaker presets, delay, and subwoofer tuning options. The Triad SA1 is also a great alternative to an AVR in a bedroom, kitchen, or other location when surround sound is not a requirement. Not only does the Triad SA1 have digital, analog audio, and HDMI ARC/eARC inputs to take the audio output from a TV to power a soundbar, it has two IR outputs to control the TV and another local source, if needed. A line-level subwoofer output rounds out the system for deep bass when connected to a powered subwoofer. The Triad SA1 can be placed horizontally or vertically, and can be installed on a bookshelf, shelf, or in a rack. WARNINGS WARNING! To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture. AVERTISSEMENT ! Pour rduire le risque de choc lectrique, nexposez pas cet appareil la pluie ou lhumidit. WARNING! Do not expose the apparatus to dripping or splashing. Do not place objects filled with liquids near the apparatus. AVERTISSEMENT ! Nexposez pas lappareil aux claboussures et loignez de toutes substances liquides. Ne placez pas les objets contenant du liquides prs de lappareil. IMPORTANT! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is not liable for any damage incurred with the misuse of this product. See Warranty. IMPORTANT ! Employer ce produit en quelque sorte autre que dcrit dans ce document vide votre garantie. De plus, Control4 nest pas responsable daucun dommage encouru avec labus de ce produit. Voyez que Warranty. IMPORTANT! To avoid generating excessive heat, do not stack amplifiers on top of each other or other equipment and allow 5 cm on all sides and above the amplifier. IMPORTANT ! Pour viter de produire de la chaleur excessive, ne pas disposer les amplificateurs, ou tout autre quipement, les uns sur les autres et laissez 5 cm de tous les cts et au-dessus de lamplificateur. FEATURES Add a high-resolution, amplified audio zone Built-in streaming music services synchronized with other Ryff-enabled devices Network control of audio and volume over an Ethernet or WiFi connection Analog and digital audio inputs support audio resolutions up to 192 kHz / 24 bit Volume, bass, treble, 6-band parametric EQ, balance, loudness, and mono summing Input gain for analog source input Audio sensing supports programmable events based on the presence of audio Built-in EQ presets for Triad speakers Supports native Ryff streaming services including Pandora, Spotify, TIDAL, Napster, Sirius XM, Deezer, iHeartradio, and more Supports built-in digital media playback including My Music, ShairBridge, and DLNA HDMI port with ARC/eARC support for audio return from TVs, including Dolby/DTS downmix support. SUPPORTED MODELS TS-SA1-200 Triad SA1, Ryff-Enabled 200W2 Streaming Amplifier BOX CONTENTS Triad SA1 AC power cord Wi-Fi antenna FRONT AND REAR PANEL DESCRIPTION REAR PANEL I J K A B D E C F G H A Power plug portAC power connection 100V 240V, 50 - 60 Hz. A B FACTORY RESETButton used to reset the amplifier to factory settings. B C IDButton used to identify the device in a Control4 system. C D IRTwo 3.5 mm IR ports. Used to control devices such as a TV or local D AVR in a Control4 system. E HDMI OUT ARC/eARCHDMI port for HDMI ARC/eARC audio. E F WIFIAntenna connector for the WiFi antenna. F G ETHERNETRJ-45 port for network connection. Used for device G control, device configuration, and digital audio streaming. H USBUSB 2.0 port used for local media file storage. H I AUDIO INTwo audio inputs. One analog stereo input, one digital I S/PDIF or digital coax input. Digital inputs accept stereo PCM audio only. J AUDIO OUT Line-level audio outputs. One stereo RCA connection and J one mono RCA connection for subwoofer out. K SPEAKER OUTBinding posts for speaker connections. K L M FRONT PANEL L Play/Pause buttonPress the button to easily play or pause music. LED LL shows power, boot, and device status. M Volume knobTurn the knob to quickly turn the volume up or down. M TRIAD INSTALLATION GUIDE - TRIAD SA1 RYFF-ENABLED 200W2 STREAMING AMPLIFIERwww.snapone.com | 1-888-400-4072 | 200-00735-A 2023-08-25 DH INSTALLING THE TRIAD SA1 MOUNTING OPTIONS The Triad SA1 can be mounted in a rack for distributed audio, or on a shelf or tabletop. Mounting kits are sold separately. Triad SA1 Rack-Mount Kit (TS-SA1RM-BL) The Triad SA1 Rack-Mount Kit Installation Guide (triadspkrs.co/sa1-rmk) and describe how to use the mounting kit. Caution! For optimal heat dissipation, the SA1 must not be placed upside down. CONNECTING THE TRIAD SA1 TO ETHERNET AND POWER 1 Plug the Ethernet CAT5E/6 cable from a local network connection into the ETHERNET port. Note: The Triad SA1 can be configured for WiFi, but must be connected to an Ethernet connection first. To configure WiFi, open System Manager, connect to the SA1, click Configure, and follow the steps in the Network Configuration Wizard. See the Composer Pro User Guide (ctrl4.co/cpro-ug) for more details. 2 Connect the provided power cable from the back of the Triad SA1 to the power outlet. When the power cable is connected, the amp should power up and the Status LED on the front should light up. TRIAD SA1 CONNECTING AUDIO TO THE TRIAD SA1 Both physical audio connections and connections in software are required to control, navigate, and use the Triad SA1 as designed. Use Composer Pro to add the driver to the desired room and set up the connections. See the Composer Pro User Guide (ctrl4.co/cpro-ug) for details. The Triad SA1 can be used as a local amplifier and/or as a streaming amplier. To use the SA1 as a streaming amplifier, connect power and network (as already shown) and speakers. CONNECTING THE TRIAD SA1 AS A LOCAL AMPLIFIER The Triad SA1 can control the local devices in a room and can deliver streaming, amplified audio to the room as well as amplified audio from local sources like a TV. The system must have a Control4 controller, such as CORE 5, in the project. 1 Connect audio sources (outputs from a TV or other audio source) to the AUDIO IN or HDMI OUT ARC/eARC. 2 Connect the speakers to the wiring connector and connect to the SPEAKER OUT output. 3 (Optional) Connect an active (self-powered) subwoofer to the SUB out. 4 (Optional) Connect IR emitters to the IR outputs to control local devices. IMPORTANT! The speaker outputs of the Triad SA1 must not be connected together or to any other common signal. In particular, the L - and R - terminals should not be joined together. Doing so will result in a fault condition and the Triad SA1 may shut down or not work as designed. TRIAD SA1 External audio source Power cable Ethernet cable IR to TV Audio out from TV

(HDMI) Triad Soundbar + In-Room Omni Sub TROUBLESHOOTING RESETTING THE TRIAD SA1 To restore the controller to the factory default image:

1 Insert one end of a paper clip into the small hole on the back of the amp labeled FACTORY RESET. 2 Press and hold the FACTORY RESET button. 3 Hold the button until the Status LED blinks white. This should take five to seven seconds. When complete, the LED turns off and the device power cycles one more time to complete the factory reset process. Caution! The factory reset process will remove any device configuration. To reset the controller network settings to the default:

1 Disconnect power to the amp. 2 While pressing and holding the ID button on the back of the amp, power on the amp. 3 Hold the ID button until Status LED button turns solid orange, and then immediately release the button. LED TROUBLESHOOTING GUIDE Status LED

= solid

= flashing (2 times a second) Booting Booting complete, has IP address Connected to Director Playing audio (white LED) Audio paused (1 white blink/sec) Audio muted (white dimmed) Firmware is updating

= flashing (4 times a second)

= flashing (once every 2 seconds) Amplifier fault Over-temperature condition Amplifier is clipping occasionally Amplifer is clipping constantly USB over-current condition No IP address Factory restore in progress (white LED) Firmware update error Factory restore error TRIAD INSTALLATION GUIDE - TRIAD SA1 RYFF-ENABLED 200W2 STREAMING AMPLIFIERwww.snapone.com | 1-888-400-4072 | 200-00735-A 2023-08-25 DH ANALOG INPUT Frequency response 48 kHz sampling 20 Hz-22 kHz +0, -0.5 dB 96 kHz sampling 192 kHz sampling Phase response

+/-0.5 deg 20 Hz -20 kHz SNR (A-weighted) DNR (A-weighted) -AES17 113 dB 114 dB Input sensitivity 2V rms THD (20-20 kHz)

< 0.002% @ 2V rms THD+N (20-20kHz)

< 0.002% @ 2V rms IMD - SMPTE

< -105 dB @ 1V rms Crosstalk

> 108 dB THERMAL Operating temperature 32 F ~ 102 F (0 C ~ 40 C) Humidity 5% to 95% non-condensing Storage

-4 F ~ 158 F (-20 C ~ 70 C) Cooling method Fanless REGULATORY/SAFETY INFORMATION To review regulatory information for your particular Triad products, see the information located on the Snap One website at https://snapone.com/legal. WARRANTY Limited 2-year Warranty. Go to https://snapone.com/legal for details. SPECIFICATIONS Zone line inputs 2 inputs, 1 analog stereo and 1 digital, (S/PDIF coax or TOSLINK optical) Audio outputs 1 stereo analog out, 1 sub/mono audio out Zone speaker outputs 1 stereo, 4-way binding posts HDMI output HDMI ARC/eARC audio input, video output USB IR 1 USB 2.0 portsupports playback of media stored on USB 2 IR ports3.5 mm jack Ethernet RJ45 jack for local network connection, 10/100/1000BaseT WiFi External antenna, 2.4GHz and 5GHz (802.11b/g/n/ac) Security options to include Encryption: 64/128 WEP, TKIP/AES, Authentication: WEP, WPA, WPA2. Front power LED 1 RGB status LED ID button Factory restore button Yes Yes Dimensions (H x W x D) 3 8.5 10.25" (7.6 21.6 26 cm) POWER AMPLIFIER Rated wattage/channel 200W @ 4 ohms / 100W @ 8 ohms (@1% THD FTC full bandwidth) Minimum load impedance Tolerates 3 ohm loads minimum Max voltage output 28.7V RMS Voltage gain 25.6 dB Damping factor

>150 Crosstalk

>91 dB DIGITAL IN TO AMP OUT Frequency response 48 kHz sampling 20 Hz-20 kHz +0, -0.5 dB 96 kHz sampling 20 Hz-20 kHz +0, -0.5dB, 20 Hz-47 kHz +0, -3dB 192 kHz sampling 20 Hz-20 kHz +0, -0.5 dB, 20 Hz-50 kHz +0, -3dB Phase response

+/-0.5 deg 20 Hz -20 kHz SNR (A-weighted) DNR (A-weighted) -AES17 117 dB 118 dB IMD - SMPTE

< -91 dB @ 10W THD+N (20-20kHz)

< 0.002%

DIGITAL IN TO PREAMP OUT Frequency response 48 kHz sampling 20 Hz-22 kHz +0, -0.5 dB 96 kHz sampling 20 Hz-43 kHz +0, -0.5dB 192 kHz sampling 20 Hz-87 kHz +0, -0.5 dB Phase response

+/-0.5 deg 20 Hz -20 kHz SNR (A-weighted) DNR (A-weighted) -AES17 113 dB 114 dB Output level 2V rms @ 0 dBFS THD (20-20 kHz)

< 0.0005% @ 2V rms THD+N (20-20kHz)

< 0.002% @ 2V rms IMD - SMPTE

< -100 dB @ 1V rms Crosstalk

> 110 dB Copyright 2023, Snap One, LLC. All rights reserved. Snap One and its respective logos are registered trademarks or trademarks of Snap One, LLC (formerly known as Wirepath Home Systems, LLC), in the United States and/or other countries. 4Store, 4Sight, Control4, Control4 My Home, SnapAV, Mockupancy, NEEO, OvrC, Wirepath, and Wirepath ONE are also registered trademarks or trademarks of Snap One, LLC. Other names and brands may be claimed as the property of their respective owners. Snap One makes no claim that the information contained herein covers all installation scenarios and contingencies, or product use risks. Information within this specification subject to change without notice. TRIAD INSTALLATION GUIDE - TRIAD SA1 RYFF-ENABLED 200W2 STREAMING AMPLIFIERwww.snapone.com | 1-888-400-4072 | 200-00735-A 2023-08-25 DH

Regulatory Compliance & Safety Information for Model TS-SA1-200 Electrical Safety Advisory Scurit lectrique consultatif Important Safety Instructions Consignes de scurit importantes Read the safety instructions before using this product. Lisez les consignes de scurit avant d'utiliser ce produit. Lisez ces instructions. 1. Read these instructions. 2. Keep these instructions. Conservez ces instructions. 3. Heed all warnings. Respectez tous les avertissements. Ne pas utiliser cet appareil prs de l'eau. 4. Follow all instructions. Suivez toutes les instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. Nettoyez-le uniquement avec un chiffon sec. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Ne pas bloquer les ouvertures de ventilation. Installer conformment aux instructions du fabricant. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Ne pas installer prs de sources de chaleur telles que des radiateurs, registres de chaleur, poles, ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur. 9. Only use attachments/accessories specified by the manufacturer. Utilisez uniquement des fixations / accessoires spcifis par le fabricant. 10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Utilisez uniquement avec le chariot, le socle, le trpied, le support ou la table spcifis par le fabricant ou vendu avec l'appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous dplacez l'ensemble chariot / appareil pour viter des blessures dues au renversement. 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com 11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Confiez toutes les rparations un personnel qualifi. Une rparation est ncessaire lorsque l'appareil a t endommag de quelque faon que ce soit le cordon d'alimentation ou la fiche est endommag, du liquide a t renvers ou si des objets sont tombs dans l'appareil, l'appareil a t expos la pluie ou l'humidit, ne fonctionne pas normalement, ou s'il est tomb. 12. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Protgez le cordon d'alimentation ne soit pitin ou pinc, en particulier au niveau des fiches, des prises et au point o il sort de l'appareil. 13. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. Unplug this apparatus during lightning storms or when unused for long periods of time. Cet quipement utilise la puissance AC qui peuvent tre soumis des surtensions lectriques, la foudre gnralement transitoires qui sont trs destructives envers les quipements terminaux connects des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causs par les surtensions lectriques ou transitoires de foudre. Pour rduire le risque de cet quipement devient endommag, il est suggr que le client envisager l'installation d'un limiteur de surtension. Dbranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilis pendant de longues priodes de temps. 14. To completely disconnect unit power from the AC mains, remove the power cord from the appliance coupler and/or turn off the circuit breaker. To reconnect power, turn on the circuit breaker following all safety instructions and guidelines. The circuit breaker shall remain readily accessible. Pour dbrancher compltement l'alimentation secteur du rseau secteur, retirez le cordon d'alimentation du coupleur de l'appareil et / ou teignez le disjoncteur. Pour reconnecter l'alimentation, allumez le disjoncteur en suivant toutes les consignes et consignes de scurit. Le disjoncteur doit tre facilement accessible. 15. This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. Ce produit repose sur l'installation des btiments pour les courts-circuits (surintensit) de protection. Assurez-vous que le dispositif de protection est assigne ne dpassant pas:

20A. 16. WARNING Power Sources, Grounding, Polarization 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com This product requires a properly grounded outlet for safety. This plug is designed to be inserted into a NEMA 5-15 (three-prong grounded) outlet only. Do not force the plug into an outlet that is not designed to accept it. Never dismantle the plug or alter the power cord, and do not attempt to defeat the grounding feature by using a 3-to-2 prong adapter. If you have a question about grounding, consult your local power company or qualified electrician. If a rooftop device such as a satellite dish connect to the product, ensure that the devices wires are also properly grounded. The bonding point can be used to provide a common ground to other equipment. This bonding point can accommodate minimum 12 AWG wire and should be connected using the required hardware specified by the other bonding point. Please use termination for your equipment in accordance with the applicable local agency requirements. AVERTISSEMENT - Sources d'alimentation, mise la terre, polarisation Ce produit ncessite une prise correctement mise la terre pour des raisons de scurit. Cette fiche est conue pour tre insre dans une prise NEMA 5-15 (trois broches mise la terre) uniquement. Ne forcez pas la fiche dans une prise qui n'est pas conue pour l'accepter. Ne dmontez jamais la fiche ou ne modifiez pas le cordon d'alimentation, et n'essayez pas de dsactiver la fonction de mise la terre en utilisant un adaptateur 3 2 broches. Si vous avez une question sur la mise la terre, consultez votre compagnie d'lectricit locale ou un lectricien qualifi. Si un appareil sur le toit tel qu'une antenne parabolique se connecte au produit, assurez-

vous que les fils des appareils sont galement correctement mis la terre. Le point de liaison peut tre utilis pour fournir une masse commune d'autres quipements. Ce point de connexion peut accueillir un fil de 12 AWG minimum et doit tre connect l'aide du matriel requis spcifi par l'autre point de connexion. Veuillez utiliser une terminaison pour votre quipement conformment aux exigences des agences locales applicables. 17. Notice For indoor use only, Internal components are not sealed from the environment. The device can only be used in a fixed location such as a telecommunication center, or a dedicated computer room. When you install the device, ensure that the protective earthing connection of the socket-outlet is verified by a skilled person. Suitable for installation in information technology rooms in accordance with Article 645 of the National Electrical Code and NFP 75. Avis Pour une utilisation en intrieur uniquement, les composants internes ne sont pas scells de l'environnement. L'appareil ne peut tre utilis que dans un lieu fixe tel qu'un centre de tlcommunication, ou une salle informatique ddie. Lors de l'installation de l'appareil, assurez-vous que la mise la terre de protection de la prise de courant est vrifie par une personne qualifie. Convient pour une installation dans des salles informatiques conformment l'article 645 du Code national de l'lectricit et NFP 75. 18. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers, and microwave ovens if placed in close proximity. Ce produit peut interfrer avec des appareils lectriques tels que les magntophones, tlviseurs, radios, ordinateurs et fours micro-ondes si placs proximit. 19. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. N'introduisez jamais d'objets d'aucune sorte dans ce produit travers les fentes du botier car ils pourraient toucher des points de tension dangereux ou court-circuiter des pices qui pourraient entraner un incendie ou un choc lectrique. 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com 20. WARNING No user serviceable parts inside. If the product is not operating properly, do not remove any part of the unit (cover, etc.) for repair. Unplug the unit and consult the warranty section of the owners manual. AVERTISSEMENT Aucune pice rparable par l'utilisateur l'intrieur. Si le produit ne fonctionne pas correctement, ne retirez aucune pice de l'appareil (couvercle, etc.) pour rparation. Dbranchez l'appareil et consultez la section de garantie du manuel du propritaire. 21. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines. Do not open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above 54 C or 130 F. ATTENTION: Comme avec toutes les batteries, il ya un risque d'explosion ou de blessure si la batterie est remplace par un type incorrect. liminez les batteries usages selon les instructions du fabricant de la batterie et applicables des directives environnementales. Ne pas ouvrir, percer ou incinrer la batterie, ou de l'exposer des matriaux conducteurs, de l'humidit, du liquide, un incendie ou une temprature suprieure 54 C ou 130 F. 22. PoE considered a Network Environment 0 per IEC TR62101, and thus the interconnected ITE circuits may be considered ES1. The installation instructions clearly state that the ITE is to be connected only to PoE networks without routing to the outside plant. PoE considr comme un environnement de rseau 0 selon IEC TR62101 et, par consquent, les circuits ITE interconnects peuvent tre considrs comme ES1. Les instructions d'installation indiquent clairement que l'ITE doit tre connect uniquement aux rseaux PoE sans acheminement vers l'installation externe. 23. CAUTION: The Optical Transceiver used with this product should use UL listed, and Rated Laser Class I, 3.3 Vdc. ATTENTION: L'metteur-rcepteur optique utilis avec ce produit doit utiliser la liste UL et la classe de laser nominale I, 3,3 Vcc. The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product L'clair et la flche dans le triangle est un signe d'alerte pour vous avertir d'une tension dangereuse l'intrieur du produit Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Attention: Pour rduire le risque de choc lectrique, ne pas retirer le couvercle

(ou l'arrire). Aucune pice rparable par l'utilisateur. Confiez l'entretien un personnel qualifi. The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. Le point d'exclamation dans un triangle est un signe d'avertissement vous signale des instructions importantes accompagnant le produit. See marking on bottom / back of product Voir le marquage sur les bas / dos du produit Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com AVERTISSEMENT! Pour rduire le risque de choc lectrique, n'exposez pas cet appareil la pluie ou l'humidit. Save these instructions Conservez ces instructions Compliance of this equipment is confirmed by the following label that is placed on the equipment:

Conformit de cet appareil est confirm par le symbole suivant qui est plac sur l'quipement:

USA & Canada Compliance FCC Part 15, Subpart B & IC Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la section 15 des rgles. Son utilisation est soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles et (2) cet appareil doit accepter toutes les interfrences reues, y compris celles pouvant entraner un fonctionnement non souhait. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de lutilisateur pour actionner cet quipement. Canada Warning Statement:

1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com CAN ICES-3 (B)/NMB-3(B) This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Ce produit rpond aux spcifications techniques applicables l'innovation, Science et Dveloppement conomique Canada. FCC Part 15, Subpart C / RSS-247 Intentional Emissions Interference Statement Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment:

Notice: The term FCC ID: and IC: before the certification number signifies that FCC and Industry Canada technical specifications were met. FCC ID: 2AJAC-TSSA1200 IC: 7848A-TSSA1200 This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-247, Antenna Requirements. Do not use any antenna other than the one provided with the unit. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and

(iii) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et lexploitation non point point, selon le cas;

(iii) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. FCC Partie 15, sous-partie C / RSS-247 Dclaration volontaire des missions interfrences Conformit de cet appareil est confirm par les chiffres de certification suivants qui sont placs sur l'quipement:

1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com Avis: Le terme FCC ID:" et "IC:" devant le numro de certification signifie que les spcifications techniques de la FCC et d'Industrie Canada ont t respectes. FCC ID: 2AJAC-TSSA1200 IC: 7848A-TSSA1200 Cet quipement doit tre install par des professionnels qualifis ou entrepreneurs conformment aux normes FCC partie 15.203 & IC RSS-247, Exigences d'antenne. Ne pas utiliser une antenne autre que celui fourni avec l'appareil. Cet metteur ne doit pas tre localis ou fonctionner avec d'autres antennes ou transmetteurs. Les oprations dans la bande 5.15-5.25GHz sont limites l'utilisation l'intrieur seulement. RF Radiation Exposure Statement This equipment complies with FCC RF and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons. Dclaration d'exposition aux radiations RF Cet quipement est conforme aux limites d'exposition aux rayonnements RF et IC de la FCC dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 centimtres entre le radiateur et votre corps ou des personnes proches. Europe Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. The full text of the EU Declaration of Conformity (DoC) is available on the regulatory webpage:

This product can be put into service in all of the EU member states, European Free Trade Association

(EFTA) and EU candidate countries without any restriction. 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com DK EL IT LU AT SI UK CH TR BG EE FR LV CZ BE IE DE HR ES CY LT HU MT NL PT RO PL FI SK SE NO LI IS MK AL RS The frequency and maximum transmitted power in EU are listed as below:

2412 - 2472 MHz: ?$ dBm 5180 - 5240 MHz: ?$ dBm WLAN 5GHz:

Operations in the 5.15-5.35GHz band are restricted to indoor usage only. United Kingdom (UK) Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. The full text of the UK Declaration of Conformity (DoC) is available on the regulatory webpage:

Recycling Snap One understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions. WEEE Compliance Snap One is committed to meeting all requirements of the Waste Electrical and Electronic Equipment (WEEE) directive (2012/19/EC). The WEEE directive requires the manufacturers of electrical and electronic equipment who sell in EU countries: (1) label their equipment to notify customers that it needs to be recycled, and (2) provide a way for their products to be appropriately disposed of or recycled at the end of their product lifespan. For collection or recycling of Snap One products, please contact your local Snap One representative or dealer. 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com Australia & New Zealand Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. About this Document Copyright 2023 Snap One All rights reserved. 1800 Continental Blvd. Suite 200-300 Charlotte, NC 28273 866-424-4489 snapone.com

Date: 2023/11/20 Federal Communications Commission 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter FCC ID: 2AJAC-TSSA1200 Product name: Triad SA1 Ryff-Enabled 200W X 2 Streaming Amplifier To whom it may concern:

We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization of model TS-SA1-200 to the FCC Rules and Regulations. VPI Technology Address : 11814 S Election Rd STE 200, Draper, UT 84020 Name Job Title : Director, Laboratories & QA e-mail

: jasons@vpitech.com

: Jason Stewart We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 862. This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Applicant Address

: Snap One, LLC

: 1800 Continental Blvd., Suite 300, Charlotte NC 28273, USA Signature

Name and Job Title. E-mail Tel. _________________________________

: Roger Midgley, Principal Compliance Engineer

: Roger.Midgley@SnapOne.com

: +18015233187 1800 Continental Blvd. Suite 300 Charlotte, NC 28273 866-424-4489 snapone.com

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 12-29-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2AJAC-TSSA1200 Applicant FRN: 0010808202 Snap One (the applicant) certifies that, as of the date of the filing of the application, Snap One will self-

designate as a U.S. agent for service of process for the above referenced FCC ID. Snap One accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Snap One accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Sincerely yours, Printed Name: Roger Midgley Title: Principal Compliance Engineer Address: 1800 Continental Blvd., Suite 300, Charlotte NC 28273, USA Tel.: +1 385-449-1193 Email: Roger.Midgley@SnapOne.com

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 09-06-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AJAC-TSSA1200 Snap One (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Roger Midgley

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 12-29-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AJAC-TSSA1200 Snap One (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, Roger Midgley

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Request for confidentiality FCC ID: 2AJAC-TSSA1200 Date: November 20, 2023 To whom it may concern:

Short-term confidentiality Pursuant to DA 04-1705 of the Commissions public notice, in order to comply with the marketing regulations in 47CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 03/24/2024 Internal Photographs External Photographs User's manual Test Set up photo Permanent confidentiality Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below:

Block Diagram Schematics Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Applicant Address

: Snap One, LLC

: 1800 Continental Blvd Suite 200-300 Charlotte, North Carolina 28273 USA Signature

Name and Job Title. : Roger Midgley, Principle Compliance Engineer _________________________________ E-mail Tel.

: Roger.Midgley@SnapOne.com

: +18015233187 1800 Continental Blvd. Suite 300 Charlotte, NC 28273 866-424-4489 snapone.com