DoorBell X1 Faceplate X3 Pick the one that best matches your home, from three faceplates. Mounting Plate X3 Pick the one for best surveillance angle. Plate Foam X1 Stabilize the mounting plate when installing it on a rough surface. Wire Harness X1 U-shaped Wires X2 Power Kit X1 Screwdriver X1
1 Wire Connectors X4 Mounting Screws X2 Anchors X2 Security Screws X1 Fixing Screws X2
Not included in the package. Drill Pencil
If you have a mechanical chime installed in your home, install the power kit and doorbell. If you have an electronic chime installed in your home, refer to its manual to install the power kit, and install the doorbell. If no chime is installed, skip power kit installation, install the doorbell.
2
1 Shut off the electricity at the breaker that controls the doorbells circuit. 2 Insert one end of the wire harness into the power kit. 3 Remove the cover from your mechanical chime. 4 Remove the existing chime wires from the terminals named TRANS and FRONT.
3 5 Connect the wire harness to the chimes terminals named TRANS and FRONT. 6 Insert the existing chime wire and the other end of the wire harness into the wire connector, and twist it tightly. Repeat this step with the other chime wire.
Wire Connectors Chime Wire Wire Harness 7 Mount the power kit to the side of the chime. 8 Replace the chime cover. 4
!!"#$!!$# 1 Shut off the electricity at the breaker that controls the doorbells circuit. 2 If
(Optional) is uneven, paste the plate foam to the mounting plate. the wall
Recommended Installation Height: 1.2 m (4 ft) above the ground. 5 3 Mark the drill points with a pencil. 4 Drill holes according to the drill points, and insert anchors. Anchor 5 Affix the mounting plate to the wall. 6 Press the doorbell button and edge to remove the doorbell's faceplate. Mounting Screw
Recommended Hole Depth: 25 to 30 mm (1 inch to 1.2 inch). 6 7 Connect doorbell to your existing doorbell wires. Fixing Screw U-Shaped Wire
Recommended Hole Depth: 25 to 30 mm (1 inch to 1.2 inch). Power Supply: 12 to 30 VAC. 7 8 Insert the pegs on the back of the doorbell into the mounting plate. 9 Lock the Security Screws. 10 Restore the electricity at the breaker.
Doorbell is powered on when its indicator steady on red. If not, make sure your electricity is off and check the wiring. If yes, proceed to doorbell setup. For the rst time use, please power on the doorbell and wait for 3 hours before using it, or the chime in your home may not work. 8
1 Add to the ClareVision app.
--Search ClareVision in the App Store or Google Play to download and install the ClareVision App.
OptionA Add doorbell (from remote network) 1. On the Home screen, go to the menu in the top left to Add Device. 9 2. Select Add Doorbell --> Select Scan QR code from shared device. 3. Scan the QR code on the device or the cover of this manual when the indicator ashes blue. 4. Waiting for the device to be added. 10 OptionBAdd doorbell (Not on a network) 1. Select Add Doorbell --> Select Device is not on a network. 11 2. Press the Reset button for 10seconds, and then you will hear a voice prompt. 3. Wait for a few seconds, until you see the LED indicator ashing blue. 4. After the reset is complete, navigate to this phone's WiFi settings and connect this phone to the doorbell's WiFi network. Once connect-
ed. return to this screen and proceed to the next step. 5. Enter the password for the device and change the device name. Once done, proceed to the next step. Wi-Fi Name: VDB_XXXXXXXX [Last 8-digit Serial No.]
Default Password: XXXXXXXX [Last 8-digit Serial No.]
Serial No. is listed on the cover of this manual. 6. Search out the Wi-Fi you want the device to connect to, and enter password.
If you want to change your doorbells Wi-Fi, press and hold the reset button for 5s and repeat this step. 12 2 After complete nal installation, place the doorbell face plate on the device. 13
Reset Button MicroSD Card Slot
)+$# Terminals Solid red Doorbell is powering on Flashing red Memory card exception Solid blue Doorbell is working Flashing blue Doorbell is ready for Wi-Fi conguration Doorbell factory reset Doorbell charging Doorbell Video Call Flashing red & blue Network exception 14
"),-./%$# 1. For AP hotspot conguration, press the Reset button for 5seconds, and then you will hear a voice prompt. 2. Wait for a few seconds, until you see the LED indicator ashing blue. 3. Follow the voice prompt to connect Wi-Fi. Wi-Fi Name: VDB_XXXXXXXX [Last 8-digit Serial No.]
Default Password: XXXXXXXX [Last 8-digit Serial No.]
Serial No. is listed on the cover of this manual. 4. Go back to the Clare Vision app after successful connection. Tap Next. 5. Search out the Wi-Fi you want the device to connect to, and enter password. 15
$)$$0#
1. In the Clare Vision app, tap the SD Card Information in the Device Settings interface to check the SD card status. 2. If the card status displays as Uninitialized, tap to initialize it. The status will then change to Normal, and it can store videos and/or pictures.
Initialize SD Card will delete any existing recording. 16
+##1 !!#$( The Video Doorbell can be connected to a NVR for viewing and recording. 1. Open the NVR interface . 2. Go to Channel Management-->Channel Conguration. 3. Click the Manually Add tab above the list to enter the add network camera (custom) interface. 4. Enter the following information. IP Camera Address: [doorbells IP address]
Protocol: HIKVISION Management Port: 8000 User Name: admin Password: [Last 8-digit Serial No.]
5. Click Add to nish adding the doorbell. 17
%!$#2,0$# Thisdevicecomplieswithpart15oftheFCCRules.Operationissubject tothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmful interference, and (2) this device must accept any interference received,includinginterferencethatmaycauseundesiredoperation. FCCwarning:
Any Changes or modications not expressly approved by the party responsibleforcompliancecouldvoidtheuser'sauthoritytooperate theequipment. Note:Thisequipmenthasbeentestedandfoundtocomplywiththe limitsforaClassBdigitaldevice,pursuanttopart15oftheFCCRules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaranteethatinterferencewillnotoccurinaparticularinstallation.If thisequipmentdoescauseharmfulinterferencetoradioortelevision reception,whichcanbedeterminedbyturningtheequipmentoffand on,theuserisencouragedtotrytocorrecttheinterferencebyoneor moreofthefollowingmeasures:
-Reorientorrelocatethereceivingantenna.
-Increasetheseparationbetweentheequipmentandreceiver.
-Connecttheequipmentintoanoutletonacircuitdifferentfromthat towhichthereceiverisconnected.
-Consultthedealeroranexperiencedradio/TVtechnicianforhelp. ThisequipmentcomplieswithFCCradiationexposurelimitssetforth foranuncontrolledenvironment.Thisequipmentshouldbeinstalled and operated with minimum distance 20cm between the radiator & yourbody. 18 IC warning
- English:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
- French:
Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1) Lappareil ne doit pas produire de brouillage;
2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. IC warning
- English:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
- French:
Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1) Lappareil ne doit pas produire de brouillage;
2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. The distance between user and products should be no less than 20cm. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. La distance entre l'utilisateur et les produits ne doit pas tre infrieure 20 cm Operations in the 5.15-5.25GHz band are restricted to indoor usage only Les oprations dans la bande 5,15-5,25 GHz sont limites une utilisation en intrieur uniquement