FCC ID: 2AEI3WLTC-DHMM-1M15 125 kHz RF reader, 125 kHz RF reader with Bluetooth communication capability.

Wall Mounted Reader Installation This installation guide applies to the ET10 Mullion Reader. Included:

Reader, Backplate, and Wall Plate

(2) #6 Screws

(1) #4-40, (1) pin-in-torx Phillips Screwdriver The Following tools are needed to install a mullion reader:

6-32 Tap (if installing on metal) 1/2 drill bit T8 Security Torx Bit (optional for increased tamper detection) 1 Mounting Holes for Wall Plate 2 Install Metal Wall Plate Drill two mounting holes at a minimum of 1.7 apart. Drill a hole in the center for the pigtail wire to pass through. Use the wall plate as a guide for drilling. Once the holes are prepared, screw the wall plate in using the provided #6 screws. Mounting hole distance is adjustable, use the provided

#6 screws Hole for Pigtail 3 Wire the Cable to the Control Panel Max Length to Panel Length AWG 200 (60 m) 300 500 22 20 18 Common Cable Connections Red Power In Black Ground Shield Brown*

Shield Ground Tamper Out Current @ 12 V Green Wiegand Data 0 / RS-485A Avg. mA Max. mA White Wiegand Data 1 / RS-485B 100 160 Yellow*

Beeper Control Blue*

Green LED Control Orange*

Red LED Control

*these wires are only used in Wiegand readers. 4 Attach the Reader to the Wall Plate Align the reader so that the tabs of the base plate slide into the slots on the wall plate and slide the reader into position. 5 Install the Reader Screw 6 Test the Reader Install the #4-40 screw or pin-in-torx at the bottom of the reader. Power the reader, the red light-bar will light, followed by a beep. Present a valid credential to the reader and the light-bar will turn green. Screw or pin-in-

torx

*Patent Pending Contact Us WaveLynx Technologies

(303) 327-1477 www.wavelynxtech.com This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Wavelynx could void the user's authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.

Wall Mounted Reader Installation This installation guide applies to the following types of readers:

ET25 Single Gang Reader with Keypad ET20 Single Gang Reader Included:

Reader, Backplate, and Wall Plate

(2) #6 Screws

(1) #4-40, (1) pin-in-torx

(4) #4 Screws The Following tools will needed to install Phillips Screwdriver a wall mount reader:

1 (25mm), 1/8 drill bits T8 Security Torx Bit (optional for increased tamper detection) 1 Install Metal Wall Plate to Single Gang Box Connect the wall plate to the single gang box using the provided #6 screws. Alternatively you can use the provided #4 screws in the four outer holes for other installation requirements. Drywall installations will require molly bolts. Standard Single Gang Box Installation Alternative for situations outside of a single gang box installation. 2 Wire the Cable to the Control Panel 3 Attach the Reader to the Wall plate Max Length to Panel Length AWG 200 (60 m) 300 500 22 20 18 Current @ 12 V and 25 C Avg. mA Max. mA 110 160 Current for ET25 @ 12 V and 25 C Avg. mA Max. mA Common Cable Connections Red Black Power In Ground Shield Shield Ground Brown*

Tamper Out Green Wiegand Data 0 / RS 485A White Wiegand Data 1 / RS 485B Yellow*

Beeper Control Blue*

Green LED Control 140 190 Orange*

Red LED Control

*these wires are only used in Wiegand readers. Align the reader so that the tabs of the base plate slide into the slots on the wall plate and slide the reader into position. 4 Install the Reader Screw 5 Test the Reader Install the #4-40 screw or pin-in-torx at the bottom of the reader. Screw or pin-in-

torx

*Patent Pending Power the reader, the red light-bar will light, followed by a beep. Present a valid credential to the reader and the light-bar will turn green. Contact Us WaveLynx Technologies

(303) 327-1477 www.wavelynxtech.com This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Wavelynx could void the user's authority to operate the equipment. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement.