FCC ID: 2AAHD-GN7214B18-1 LED Lighting Set

Low Voltage Lighting Systems User Guide Please read this user guide before installing and using your Low Voltage Lighting Systems 1THE COMPONENTS LIST 5Vdc, 1.2Watts RGB LED strip USB Connector:

Connect the lights to the controller USB connector: connect the 5Vdc, min.2.1A power 1> LED controller ----1pcs;

2> RF control---1pcs;

3> LED lighting ---2pcs;

4> LED strip---1pcs 5Vdc, 1.2Watts RGB LED strip 5Vdc, 7.2Watts RGB LED strip 2INSTALLATION 1>Slotted hole: according to the following dimensions;

Units:mm 2>Fix the light in the slotted hole;

3>Screw the LED controller on furniture,The controller cant be installed in closed metal parts;

4>Connect the lights to the controller;

5>Connect the controller to the 5Vdc power supply;

Pull out the battery insulation Battery replacement method 6>Operate the Remote control to control the light bar(pull out the battery insulation before use);

3SPECIFICATIONS Input :5Vdc, Min.2.1A LED lighting: Input: DC 5V Power: Max. 10W 4RF wireless Remote RGB LED Controller Instructions Turn Off Music Activation Mode Increase /

Decrease Speed 9 RGB Colors Turn On Auto Timer Brightness Adjustment Dynamic Mode Remote control pairing instruction:

1. Connect the light fixture to a USB port. Press and hold the ON"

button on the remote control within 5 seconds after the LED lights are powered on. The LED lights flash, indicating it is in searching and pairing mode. 2. The LED lights stop flashing, indicating that the remote control has been successfully paired with the light fixture. 3. This light fixture will not be controlled by another remote control until you perform the above pairing operation again. AP name is "duoCo Strip". Please search for and install the APP in the QR code. Functions are listed as follows:

1. Adjust the brightness and color temperature of 16 million kinds of colors for monochrome LED strip.

(1) Click to show the lamp list, view lamp list:

Lamp list Status of device connection Status of device connection

(2) Switch to color and brightness interface:

Click to show the lamp list switch the color wheel Click to display setting view Lamp switch button Before using the remote control pull out the bottom plastic piece 2. Six color sequence modes to choose from: Static, Strobe Flash, Gradual Change, Cross-Fade, and Jump Change, each with multiple color modes. 3. In music sync mode, the LED lights can change color and speed to sync according to the rhythm of the music. 4. In External Microphone mode: the Built-in high-sensitivity microphone can adjust the speed and color of the lighting to match the sounds around you. 5. Schedule: Select the date and time to turn on / off the timing light. The light will turn on / off for the time you set. Display the RGB value click to manual adjustment view Click square icon to adjust the color Adjust the color Click to shift the interface

(3) Switch to the mode interface:

(5) Switch to the microphone rhythm interface:

(6) Switch to the schedule:

Scroll the selection mode Adjust speed Adjust luminance

(4) Switch to the music rhythm:

Previous song Pause / play Next song Music rhythm through cell phone microphone Phone Microphone Mode Set the time of Light-On Set the time of Light-Off Enable or disable the light-On function Repeat setting No selection for once light0n Enable or disable the Light-0ff function Repeat setting No selection for once Light-Off Recycle mode Music rhythm through the microphone on the product External Microphone Mode

(7) Switch to the modify pin sequence interface:

Music list Click to save the new assignment Change the real color of this line 4-style rhythm Change the sensitivity of MIC to match the sound Local music:

1. Download local music on android phone:

(1) Android phone use music players to download songs or copy songs from computers to mobile phones.

(2) Restart duoCol Strip and switch to music Rhythm Interface to see the newly imported music files

. 2. Download local music on iPhone

(1) Install iTunes software on your computer (Apple or Windows).

(2) Log in to iTunes with the same Apple ID account on the iPhone.

(3) Use iTunes to import downloaded music files on your computer.

(4) The imported music files will be synchronized to the iPhone in real time.

(5) Restart and switch to music Rhythm Interface to see the newly imported music files. FCC Statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the followi ng two conditions: (1) this device may not cause harmful interference, and (2) this devi ce must accept any interference received, including interference that may cause undesir ed operation. Changes or Modifications not expressly approved by the party responsible could void the users authority to operate this device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. RF Exposure statement:

The device has been evaluated to meet general RFexposure requirement IC statement:

This device complies with Industry Canada Licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. RF Exposure statement:

the device has been evaluated to meet general RF exposure equirement.

Whalen LLC dba Whalen Furniture Manufacturing Agent Authorization Letter 2024-04-07 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern:

We, the undersigned, hereby authorize (The Hong Kong Standards and Testing Centre Limited) to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Print nameDwayne Myers Title: Director - Quality Engineering Signature:

Whalen LLC dba Whalen Furniture Manufacturing 2024-04-07 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for (FCC ID: 2AAHD-GN7214B18-1) The applicant: Whalen LLC dba Whalen Furniture Manufacturing certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Print nameDwayne Myers Title: Director - Quality Engineering Signature:

Whalen LLC dba Whalen Furniture Manufacturing 2024-04-07 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for (FCC ID: 2AAHD-GN7214B18-

1) The applicant: Whalen LLC dba Whalen Furniture Manufacturing certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Print nameDwayne Myers Title: Director - Quality Engineering Signature:

Whalen LLC dba Whalen Furniture Manufacturing Long Term Confidentiality Request Letter Date: 2024-04-07 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR EUT NAME: LED Lighting Set MODEL: GN7214B-18 FCC ID: 2AAHD-GN7214B18-1 To Whom It May Concern:

This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the (block diagram/schematics/PCB /operational description ) required to be submitted with this application be permanently withheld from public review. The above documents are company proprietary information that could never get into the possession of your competition. Please contact me if there is any information you may need. Sincerely, Print nameDwayne Myers Title: Director - Quality Engineering Signature:

Attestation Statements -US agent 2024-04-07 TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA RE: Attestation Statements Part 2.911(d)(7) request for (FCC ID: 2AAHD-GN7214B18-1) Whalen LLC dba Whalen Furniture Manufacturing, the undersigned, hereby authorize Whalen LLC dba Whalen Furniture Manufacturing to act as our designated U.S. agent for service of process, Whalen LLC dba Whalen Furniture Manufacturing accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Whalen LLC dba Whalen Furniture Manufacturing accepts the responsibility to act as designated U.S. agent for service of process, provides an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Information Company name:

Address:

FRN:

Contact Name:

Telephone No:

Email:

Print name: Dwayne Myers Title: Director - Quality Engineering Whalen LLC dba Whalen Furniture Manufacturing 1578 Air Wing Road, San Diego, CA 92154 0022769426 Dwayne Myers 86- 18665131211 DwayneMyers@whalenasia.com Whalen LLC dba Whalen Furniture Manufacturing 1578 Air Wing Road, San Diego, CA 92154 0022769426 Dwayne Myers 86- 18665131211 DwayneMyers@whalenasia.com Signature:

U.S. Agent Information:

Company name:

Address:

FRN:

Contact Name:

Telephone No:

Email:

Print name: Dwayne Myers Title: Director - Quality Engineering Signature: