FCC ID: 2AJACT4TS System Controller

T4 Series Tabletop Touchscreens Installation Guide Supported models Warnings C4-T4T8-xx 8" Tabletop Touchscreen (black or white) C4-T4T10-xx 10" Tabletop Touchscreen (black or white) Introduction The Control4 T4 Series Tabletop Touchscreens offer complete system control in an elegant, compact, and portable design. The touchscreens are equipped with a full capacitive screen, audio and video Intercom (with the built-in camera) using SIP, and more. This touchscreen can be located anywhere, and the convenient recharging station enables it to be used as either a tabletop or portable interface. The touchscreen uses an AC power adapter for power and Wi-Fi for network connectivity. Note: 802.11b is not recommended for video intercom. We recommend using Wireless-N. See Specifications for more information. Box contents Tabletop Touchscreen Recharging station Recharging station power cord Accessories available for purchase Tabletop Permanent Mount Kit (C4-T4PMNT) T4 Touchscreen Tabletop 8" Base (C4-T4TBS8) T4 Touchscreen Tabletop 10" Base (C4-T4TBS10) Warning! This product must be grounded in accordance with the National Electrical Code (NEC) requirements. Avertissement ! Ce produit doit tre fondu selon les conditions lectriques nationales de code (NEC). Caution! Do not place the touchscreen near sources of heat or expose to direct sunlight for an extended time. Avertissement ! Ne placez pas lunit prs des sources de chaleur ou exposition pour diriger la lumire du soleil pendant une priode prolonge. Caution! This product generates heat. The room must have adequate ventilation or the ability to dissipate heat effectively. Avertissement ! Ce produit produit de la chaleur. La salle doit avoir ventilation proportionne ou la capacit dabsorber la chaleur efficacement. Caution! Use this product only in dry locations. Avertissement ! Employez ce produit seulement dans des endroits secs. Caution! Do not use pens or sharp objects to navigate or make selections on the touchscreen. To select an item or scroll through a list, use your fingertip. Avertissement ! Nemployez pas les stylos ou les objets pointus pour diriger ou pour faire des choix sur lcran. Pour choisir un article ou un rouleau par une liste, employez votre bout du doigt. Caution! Improper use or installation can cause DAMAGE OF PROPERTY. Avertissement ! Lutilisation ou linstallation inexacte peut causer DAMAGE DE PROPRIT. Important! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See Warranty. 11 Views Front Specifications and requirements Specifications Model Numbers C4-T4T10-BL, C4-T4T10-WH C4-T4T8-BL, C4-T4T8-WH Screen Resolution: 1920 1200 Capacitive touch Camera: 720p Wireless network 802.11b/g/n 2.4 GHz 802.11a/n/ac 5 GHz Security: WEP, WPA/WPA2 PSK, 802.1x EAP, PEAP Notes: (1) While technically the touchscreen can use 802.11b, 802.11b is not supported. (2) 802.11n is recommended for best performance. Even with 802.11n, broadcasting to several devices will degrade Video Intercom response time and images. Broadcasting to additional devices will further degrade performance. See Wireless Network Limitations. Power supply 100-240V AC, 50/60 Hz International adapters included Charging base connections: 5V DC power 8" Touchscreen: 178 130 19 mm (7.0 5.1 0.75") 8" Base: 106 79 56 mm (4.17 3.11 2.21") 10" Touchscreen: 245 172 23 mm (9.65 6.77 0.91") 10" Base: 115 102 66 mm (4.53 4.02 2.60") Dimensions

(WHD) Weight Operating temperature Storage temperature Requirements 8" Touchscreen: 1.05 lb (0.47 kg) 8" Charging base: 1.4 lb (0.64 kg) 10" Touchscreen: 1.35 lb (0.60 kg) 10" Charging base: 1.05 lb (0.46 kg) 0 to 40 C (32 to 104 F)

-20 to 70 C (-4 to 158 F) A controller fully installed and configured with Control4 OS3.2.1 or newer. A wireless network (IEEE 802.11b/g/n) must be installed and available with a wireless access point (WAP). Security can be WEP, WPA/WPA2 PSK, 801.1x EAP, or PEAP. For AC power, you must have access to an AC power outlet

(AC power adapter included). A B C D E E F G A Camera LED B Camera C Light sensor D Stereo microphones E 8" or 10" diagonal, capacitive 1920 1200 display Back (with charging station) B C A D A Power button. Press to enter or exit battery saving mode, press and hold to turn off or restart, or press and hold for 10 seconds to power off. B Reset pinhole. Press to reset, or press and hold to reset and restore factory defaults. C Docking connector D Volume buttons E Speakers F Charging station base G 5V DC power connector 2 Touchscreen placement If you dont see the network you want:

Place the touchscreens charging station on any level surface near a power outlet. For more information on mounting the touchscreen, see Portable under Mounting options below. Note: Consider the angle of the touchscreens camera and the sitting or standing position of the people who will use it while its on the charging station. Connect power and Wi-Fi The touchscreen uses a Wi-Fi network connection, so it can be positioned anywhere in the home with a strong WiFi signal and access to a power outlet. To connect power and Wi-Fi:

1 Tap +, then tap the Network SSID field and type the SSID

(name) of the network by using the on-screen keyboard. 2 Tap the Security field, then select the type of security to use. 3 Tap the Password field, then use the on-screen keyboard to type the password (if required). Note: If you need to enter a static IP address, follow the instructions under To set a wireless static IP address below before proceeding. 4 Tap Save. The new network is added to the bottom of the network list. To set a wireless static IP address:

1 Scroll down and tap Show advanced options. 1 Place the touchscreens charging station near a power outlet. 2 Tap IPsettings, then tap Static. 3 Select each box one at a time and use the on-screen 2 Connect the AC power adaptor to a power outlet and the charging station. 3 Make sure you have Wi-Fi working in the home. If a home requires a large number of Wi-Fi video intercom devices, ensure that you have a robust Wi-Fi network

(possibly consisting of multiple access points). Connection notes: (1) Video Intercom. Although this device supports 802.11b/g/n, 802.11 b is not recommended for Video Intercom use. (2) We recommend Wireless-N for best performance. Wireless network limitations: Many Wi-Fi access points handle Multicasts (Wi-Fi simultaneously sent to multiple devices, for example, when the touchscreen broadcasts video to all stations) by slowing down transmission speed to the 1 Mb basic rate. This can cause overall Wi-Fi congestion in the Wi-Fi network during the broadcast. Video Intercom response times and images may degrade at each device. keyboard to type the:

IP address Gateway Network prefix length DNS 1 (preferred) DNS 2 (alternate) Add and configure in Composer Pro After the touchscreen is installed and appears on the home network, use Composer Pro to add it to the Control4 system and configure it. Use the Composer Pro System Design and Connections views to add and configure this device. To add and configure a T4 touchscreen to a project:

1 Add the T4 Tabletop Touchscreen driver to your project. 2 Identify the device to the project, select the touchscreen in Composer Pros Connections > Network view, click Identify, then tap Identify on the touchscreen. System Design view, then view and change the properties in the Properties pane as needed. Back LightClick the arrows or type numbers to set the network connection type. light level, then click Set. Advanced properties include:

Enable CameraAllows you to enable or disable the Intercom (nested under the touchscreen) properties:

AppearanceSelect to hide the touchscreen from appearing in Navigators as an available device. BehaviorSelect the modes you want this touchscreen to Audio ControlSelect the volume of individual audio camera. support. settings. Connect to Wi-Fi To set up Wi-Fi on the touchscreen:

configuration page opens. 1 After the touchscreen starts up, tap Network. The network 3 To configure the properties, select the touchscreen in the 2 Under Wi-Fi, tap or slide OFF/ON to enable Wi-Fi, then tap the Wi-Fi field to open a list of available networks. Properties include:

3 Tap the network name you want to connect to. Network ConnectionReports the touchscreens current 4 Tap the Password field, then use the on-screen keyboard to type the password (if required). Note: If you need to enter a static IP address, follow the instructions under To set a wireless static IP address below before proceeding. 5 Tap Connect. 3 Sip InformationInformation for integrating the 3 Remove the charging stations bottom cover by removing touchscreen into your SIP/VoIP system. the two screws shown. Custom ButtonsSelect to enable and label the two available custom buttons. Alternate CameraSelect to use an external camera for the video associated with the touchscreen, for example, a security camera mounted to the side of the entrance and pointing at the door. Mounting Place the charging station on any level surface. While positioning the touchscreen, consider the angle of the touchscreens camera and the position of the people who will use it while its on the charging station. Portable use You can set the touchscreen onto the charging station for recharging and tabletop use, and lift the screen from the charging station for portable use (like a tablet). Tip: For easy and smooth separation of the touchscreen from the charging station, slightly rotate the touchscreen while lifting it. Permanent mount You can mount a touchscreen permanently to a surface, such as a table, using the optional T4 Tabletop Permanent Mount Kit

(C4-T4PMNT). 1 Peel off the plastic cover on the touchscreens docking connector recess. Base screws 4 Save the cover and screws. 5 Using a #2 Phillips screwdriver inserted from the base of the charging station, remove the two screws that secure the charging stations top docking connector cover (do not remove the screw holding the PCB), then discard the two screws you removed. 6 Screw the base to the back of the touchscreen as shown using the new threaded, black screws provided. DO NOT ATTEMPT TO USE THE ORGINAL SCREWS REMOVED IN STEP 5 OR YOU WILL PERMANANTLY DAMAGE THE THREADS ON THE TOUCHSCREEN. 2 Use the Phillips-head flat screws provided in the kit to install the permanent-mount adapter into the touchscreens docking connector recess. 7 Reinstall the base bottom cover. 4 8 To install the charging station permanently into a table or countertop, remove the small rubber discs covering the threaded holes in the base. Troubleshooting To power cycle the touchscreen:

9 Install the threaded posts (all thread) into the base of the charging station. 1 Press and hold the

(power) button for several seconds until the touchscreen turns off. 2 Press and release the

(power) button again to turn on. To perform a factory data reset:

1 On the touchscreens main screen, tap Settings, System Info, then Factory data reset.

- OR -

- OR -

If the touchscreen has not yet been configured, tap About, then Factory data reset. To reset without using the display screen:

a Dock the touchscreen onto its charging station. b Press and hold the volume up button while using a straightened paper clip to press and release the reset button. Reset hole c Keep holding down the volume up button until the icon below appears on the screen, then release the button. d A message appears, indicating that data is being erased. 10 Using the template and a 1/4" drill, drill two holes into the surface where you are mounting the touchscreen. Maximum surface thickness is 32 mm (1.25"). 11 Mount the charging station assembly into the mounting holes and secure it in place using a washer and nut. 5 Additional resources The following resources are available for more support. Knowledgebase and forums on Tech Community Technical Support Control4 website: www.control4.com Composer documentation available at ctrl4.co/docs. Warranty and legal notices Find details of this products 2-Year Limited Warranty at snapav.com/warranty, or request a paper copy from Customer Service at (866) 424-4489. Find other legal resources, such as regulatory notices and patent information, at snapav.com/legal. More help For the latest version of this document, open this URL or scan the QR code on a device that can view PDFs. LATEST VERSION OF THIS DOCUMENT ctrl4.co/t4-tabletop-ig T4 DATA SHEET ctrl4.co/t4-ds Copyright 2020, Wirepath Home Systems, LLC. All rights reserved. Control4 and Snap AV and their respective logos are registered trademarks or trademarks of Wirepath Home Systems, LLC, dba Control4 and/or dba SnapAV in the United States and/or other countries. Snap AV and Wirepath are also registered trademarks or trademarks of Wirepath Home Systems, LLC. Other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice. A 200-00683-A 2020-10-09 MS 8" and 10" T4 Series In-Wall Touchscreen Installation Guide Supported models Accessories available for purchase C4-T4IW8-BL 8" T4 In-Wall Touchscreen, Black Pakedge 802.3at/af Gigabit PoE+ Injector (PI-30AT), or Araknis Networks Gigabit PoE+ Injector

(AN-ACC-INJ-POE-30W), each sold separately. Wall box options (sold separately)Metal and plastic, for new construction or retrofit installations. In-Wall Touchscreen Wall Box Kits - New Construction In-Wall Touchscreen Wall Box Kits - Retrofit Plastic (C4-NWB57C-P) Metal (C4-NWB57C-M) Plastic (C4-RWB57C-P) Metal (C4-RWB57C-M) For wall box installation details, see:

In-Wall Touchscreen Wall Box Installation Guide-New Construction (ctrl4.co/wallbox-new) In-Wall Touchscreen Wall Box Installation Guide-Retrofit

(ctrl4.co/wallbox-retro) C4-T4IW8-WH 8" T4 In-Wall Touchscreen, White C4-T4IW10-BL 10" T4 In-Wall Touchscreen, Black C4-T4IW10-WH 10" T4 In-Wall Touchscreen, White Introduction The Control4 T4 Series 8- and 10-inch In-Wall Touchscreens offer complete system control in an elegant and compact design. The touchscreens are equipped with a full capacitive screen, audio and video Intercom (with the built-in camera) using SIP, and more. This touchscreen works great in either new construction or retrofit installations. For power and network connectivity, choose from three options:

Ethernet with PoEThe Ethernet network connection is provided through the PoE Injector. No additional wiring is needed. Ethernet with ACConnect the touchscreen to one of the LAN ports on the gateway/router using an Ethernet cable. AC power is used to power the touchscreen. WiFi with ACThe internal Wi-Fi will communicate with the LANs wireless AP, so no additional network wiring is needed. AC power is used to power the touchscreen. Note: 802.11b is not recommended for video intercom. We recommend using Wireless-N. See Specifications and Power and Network Installation Options for more information. Box contents 8" or 10" T4 In-Wall Touchscreen Power box (to power the touchscreen) Two screws (to attach the power box to the wall box) Set screw (to secure the touchscreen to the power box) Set screw tool (3/32" hex wrench) 11 Warnings Specifications and requirements Warning! The touchscreen must be protected by an external circuit breaker or a fuse rated at 6A maximum when used in Europe. AVERTISSEMENT ! Pour rduire le risque du feu ou de choc lectrique, nexposez pas cet appareil la pluie ou lhumidit. Warning! Do not place the touchscreen near sources of heat or expose to direct sunlight for an extended period of time. AVERTISSEMENT ! Ne placez pas lunit prs des sources de chaleur ou exposition pour diriger la lumire du soleil pendant une priode prolonge. Warning! Install in accordance with all national, state, and local electrical codes. AVERTISSEMENT ! Installez selon tous les national, tat, et codes lectriques locaux. Warning! This product generates heat. The room must have adequate ventilation or the ability to dissipate heat effectively. AVERTISSEMENT ! Ce produit produit de la chaleur. La salle doit avoir ventilation proportionne ou la capacit dabsorber la chaleur efficacement. Warning! This product must be grounded in accordance with the National Electrical Code (NEC) requirements. AVERTISSEMENT ! Ce produit doit tre fondu selon les conditions lectriques nationales de code (NEC). Warning! Use this product only in dry locations. AVERTISSEMENT ! Employez ce produit seulement dans des endroits secs. Caution! Do not use pens or sharp objects to navigate or make selections on the touchscreen. To select an item or scroll through a list, use your fingertip. AVERTISSEMENT ! Nemployez pas les stylos ou les objets pointus pour diriger ou pour faire des choix sur lcran. Pour choisir un article ou un rouleau par une liste, employez votre bout du doigt. Caution! Improper use or installation can cause DAMAGE OF PROPERTY. AVERTISSEMENT ! Lutilisation ou linstallation inexacte peut causer DAMAGE DE PROPRIT. Important! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See Warranty. Important ! Utilisant ce produit en quelque sorte autre que dcrit dans ce document vide votre garantie. De plus, Control4 nest pas responsable daucun dommage encouru avec labus de ce produit. Voyez que Warranty. Specifications Model Numbers C4-T4IW10-BL, C4-T4IW10-WH, C4-T4IW8-BL, C4-T4IW8-WH Screen Resolution: 1920 1200, capacitive touch Camera: 720p Network Ethernet or Wi-Fi 802.11b/g/n 2.4 GHz 802.11a/n/ac 5 GHz Security: WEP, WPA/WPA2 PSK, 802.1x EAP, PEAP Notes: (1) While technically the touchscreen can use 802.11b, 802.11b is not supported. (2) 802.11n is recommended for best performance. Even with 802.11n, broadcasting to several devices will degrade Video Intercom response time and images. Broadcasting to additional devices will further degrade performance. See Wireless Network Limitations. Power supply PoE (IEEE 802.3af) 13 W peak 100-240V AC, 50/60 Hz Dimensions (W H D) 8" model: 175 127 13 mm (6.9 5.0 0.53") 10" model: 239 165 13 mm (9.4 6.5 0.53") Wall box: 68 104 61 mm (2.7 4.1 2.4") Power box: 71 114 46 mm (2.8 4.5 1.8") Weight (with mid-box) 8" model: 0.41 kg (0.9 lb) 10" model: 0.68 kg (1.5 lb) Operating temperature 0 to 40 C (32 to 104 F) Storage temperature

-20 to 70 C (-4 to 158 F) Requirements OS3.2.0 or later. A controller fully installed and configured with Control4 Control4 Touchscreen wall box installed. See Accessories. If using Ethernet with PoE power:

Ethernet network installed and available that includes a gateway/router/switch Control4 PoE Injector (model #AC-POE1-B) or another third-party, UL/ANSI-certified PoE injector or switch. Two Ethernet Cat 5/6 cables: (1) one that runs from the Ethernet gateway/router/switch to the PoE injector/switch and (2) one that runs from the PoE injector/switch to the Ethernet connection in the touchscreens wall box. If using Ethernet with AC power:

Ethernet network installed and available that includes a gateway/router/switch Access to in-wall AC power (neutral connection required) One Ethernet Cat 5/6 cable that runs from the Ethernet gateway/router/switch to the touchscreen A 14-gauge electrical wire long enough to pull between the touchscreen and the power source If using Wi-Fi with AC power:

Wireless network (IEEE 802.11b/g/n) installed and available with a wireless access point (AP). Security can be WEP, WPA/WPA2 PSK, 801.1x EAP, or PEAP. Access to in-wall AC power (neutral connection required) A 14-gauge electrical wire long enough to pull between the touchscreen and the power source 2 Front view Top view A B C D E E G D F A Indicator LED (startup, camera in use, audio listening) B Camera C Ambient light sensor D Stereo microphones E 8 or 10 diagonal, capacitive 1920 1200 display Back view A CB A Reset pinhole buttons-For resetting and restoring the touchscreen to factory default settings. B Upper mount tab C PowerPress this button to turn the touchscreen on, or press and hold it to turn the touchscreen off. D Docking electrical connector E Locking tab F Set screwsecures the touchscreen to the power box. G Stereo speakers 3 A B C A Power button. Press to turn the display on and off, press and hold to select Power off or Restart, or press and hold for 10 seconds to reset the device. B Center pinhole. Not used. C Reset pinhole. Press to reset, or press and hold until Erasing appears on the screen to restore factory defaults. Touchscreen placement Place the touchscreen in a convenient location at eye level, typically near the entrance of the room, about 145 to 155 cm

(57to61 inches) from the floor (Figure 3). Note: Consider the camera on the panel and the height of the people in the home who will use the camera for Video Intercom. Important: The top of the touchscreen must be mounted no higher than 2 m (6.6 ft.) above the floor. Figure 1: Touchscreen placement Touchscreen AC power

(unless using PoE) LED indicator The LED on the touchscreen indicates the camera status of the camera and booting information as described in the next table. Camera/LED color state Touchscreen status Off Green Camera is off Camera is on Green (blinking slowly) Touchscreen is booting Installation Warning! Before installing the touchscreen, switch off the circuit breaker or remove the fuse from the fuse box. AVERTISSEMENT ! Pour lendroit o vous installez lcran tactile, coupez le disjoncteur ou enlevez le fusible de la bote de fusible. Important! Before you can complete the instructions below, you must have an 8" or 10" Touchscreen wall box installed according to the documentation provided in the wall box kit. See Accessories for details. Important ! Avant de lire les instruction ci-dessous, il vous faut un support mural install suivant la documentation fournie avec le kit du support mural. Plus de dtails dans la partie << Accessoires >>. Important! When cutting the opening for the wall box, do not cut the opening too large. Be conservative and cautiously enlarge it as needed. Important ! En coupant louverture pour le support mural, ne faites pas une ouverture trop grande. Soyez prudent, et agrandissez la avec prcaution. Power and network installation options This device uses an Ethernet or Wi-Fi network connection and can be powered using PoE or AC power. Choose one of the following options to install the power and network communication. Caution! Do not attempt to use PoE and AC power at the same time. Choose only one power option. ATTENTION ! Ne pas tenter dutiliser PoE et AC en mme temps. Choisir une seule option dalimentation. Option 1: Ethernet connection with PoE PoE supplies DC power on the Ethernet cable using a PoE Injector (model #AC-POE1-B) or a third-party PoE solution to provide the touchscreen with power and a network connection. The touchscreen works with the Control4 PoE Injector or a third-

party PoE Injector. To set up your PoE and Ethernet connection with a PoE Injector:

1 Attach the PoE Injector according to the instructions in your PoEs installation guide if provided. Control4 PoE Injector instructions are provided later in this document. 2 Pull the Ethernet cable from that location to where you want to install the touchscreen. Figure 2: Ethernet with PoERequires Ethernet connection to PoE injector Option 3: Wi-Fi connection with AC Place the touchscreen above a power source, for example, an outlet. Ensure that you have Wi-Fi in the home (Figure 6). Important: The touchscreen cannot connect to a Wi-Fi network when already connected by Ethernet. Notes: (1) Video Intercom. Although this device supports 802.11b/g/n, 802.11 b is not recommended for Video Intercom use. (2) We recommend Wireless-N for Video Intercom. See the Composer Pro User Guide for details about the touchscreens properties. Wireless Network Limitations: Many Wi-Fi Access Points handle Multicasts (Wi-Fi simultaneously sent to multiple devices, for example, when the touchscreen broadcasts video to all stations) by slowing down transmission speed to the 1 Mb basic rate. This can cause overall Wi-Fi congestion in the Wi-Fi network during the broadcast. Video Intercom response times and images may degrade at each device. If a home requires a large number of Wi-Fi Video Intercom devices, ensure that you have a robust Wi-Fi network (possibly consisting of multiple access points). Figure 4: Wi-FiRequires AC power and AP Place touchcreen here Option 2: Ethernet connection with AC Connecting PoE The Ethernet is connected directly to the switch (Figure 5). This power connection requires both neutral and hot connections. Figure 3: EthernetRequires a connection to Ethernet and AC power Connect the PoE injector to power and the network, and then connect it to the power box. It can be located anywhere along the cable that connects the power box to the network switch. Wireless access point WiFi Controller Switch Power installation Prepare the plastic power box for installation into the wall box by inserting either the Ethernet cable or the AC power cable into the power box, and then follow the instructions. To install a Control4 PoE injector:

1 Connect the Control4 PoE injector to an AC outlet using the power cord. 2 Connect one of the LAN ports on the network switch to the PoE Injectors LAN port using Cat 5/6 Ethernet cable. 3 Pull a cable going from the PoE injectors PWR LAN-OUT port through one of the touchscreens left-side wall box knockout holes. 4 Go to Connecting to a wired network below. 4 Connecting to a wired network To connect to a wired network:

1 Pull the in-wall Ethernet cable through a left-side knockout hole of the wall box, then plug it into the Ethernet jack on the back of the power box (Figure 8). Figure 5: Insert Ethernet cable into power box Note: The Ethernet port on the power box does not have functioning indicator LEDs. 2 Go to Attach the power box and touchscreen below. Connecting AC power The steps below represent a typical U.S. installation. Caution: Use only 14 AWG wire for AC connections. For supply connections, use wires suitable for at least 60 C (140 F). 1 Connect the wires to the AC power source for the touchscreen according to national and local electrical codes. Installation may require alternative wires and the use of the included terminal block. 2 Pull the power cable through a right-side knockout hole of the wall box to the terminal block. 3 Strip the black and white power wire ends to 1/4" as necessary. Using a flat-head screwdriver, loosen the screws on the power boxs terminal block and connect the power wires to each terminal (Figure 5), then tighten the screws. Figure 6: Connect AC power to terminal block 4 If using a plastic wall box with an exposed bare copper ground, wrap the ground in electrical tape or heat shrink tape/tubing. If using a metal wall box, attach the ground wire to the wall box. Attach the power box and touchscreen To attach the power box and touchscreen:

1 Align and bend the wires to fit them inside the wall box. 2 Slide the power box into the wall box, then secure the power box to the wall box using the two screws provided

(Figure6). Caution: Do not use an electric driver to tighten the screws. Overtightening can result in the power box becoming slightly warped, resulting in a poor electrical docking connection. Use only a hand screwdriver to tighten the screws. Tip: If overtightened screws result in the power box warping, loosen the screws until the power box is flush to the wall. Figure 7: Secure power box to wall box 3 Angle the top of the touchscreen toward the wall, insert the top mounting bracket onto the power box, then press the bottom of the touchscreen into place (a magnet will hold it in position). Figure 8: Attach the touchscreen top first Line (L) Neutral (N) 4 Secure in place with the included set screw and 3/32" hex wrench. 5 Add and configure in Composer Pro After the touchscreen is installed and appears on the home network, use Composer Pro to add it to the Control4 system and configure it. Use the Composer Pro System Design and Connections views to add and configure this device. To add and configure a T4 touchscreen to a project:

1 Add the T4 8/10" In-Wall Touchscreen driver to your project. 2 Select the touchscreen or its Intercom component in the project trees System Design view. 3 View and change the properties in the Properties pane as needed. Properties include:

Network ConnectionReports the touchscreens current network connection type. Back LightUse the arrows or type numbers to set the light level, then click Set. Adaptive Brightness EnabledEnables or disables adaptive brightness. Advanced properties include:

Camera EnabledEnables or disables the camera. RebootRemotely reboots the touchscreen. Intercom (nested under the touchscreen) properties:

Appearance Exclude from NavigatorSelect to hide the touchscreen from appearing in user interfaces as an available device. High Quality EnabledSelect to use the highest resolution setting for the camera. Dial Pad UI EnabledEnables the on-screen dial pad. Behavior Select the modes you want this touchscreen to support: Play Door Chime, Do Not Disturb, Auto Answer, Send Video, Monitor Mode, Echo Calibration, Disable Echo Cancellation. Audio ControlSelect the volume of individual audio settings. Sip InformationInformation for integrating the touchscreen into your SIP/VoIP system. Custom ButtonsSelect to enable and label the two available custom buttons Alternate CameraSelect to use an external camera for the video associated with the touchscreen, for example, a security camera mounted to the side of the person operating the touchscreen. Configuration Configure the touchscreen for wireless (optional) To configure the touchscreen for wireless:

1 After initialization, tap Network. The network configuration page opens. 2 Under Wi-Fi, tap or slide OFF/ON to enable WiFi, then tap the Wi-Fi field to open a list of available networks. 3 Tap the network name you want to connect to. 4 Tap the Password field, then use the on-screen keyboard to type the password (if required). Note: If you need to enter a static IP address, follow the instructions under To set a wireless static IP address below before proceeding. 5 Tap Connect. If you dont see the network you want:

1 Tap +, then tap the Network SSID field and type the SSID

(name) of the network by using the on-screen keyboard. 2 Tap the Security field, then select the type of security to use. 3 Tap the Password field, then use the on-screen keyboard to type the password (if required). Note: If you need to enter a static IP address, follow the instructions under To set a wireless static IP address below before proceeding. 4 Tap Save. The new network is added to the bottom of the network list. To set a wireless static IP address:

1 Scroll down and tap Show advanced options. 2 Tap IPsettings, then tap Static. 3 Select each box one at a time and use the on-screen keyboard to type the:

IP address Gateway Network prefix length DNS 1 (preferred) DNS 2 (alternate) Configure the touchscreen for Ethernet If you want to use DHCP (default) for your Ethernet connection, no further setup is required. To configure a static IP address for Ethernet:

1 After initialization, tap Network. The network configuration page opens. 2 Tap Ethernet. The Ethernet settings screen opens. 3 Tap Static IP Settings, then tap Use static IP. 4 Select each box one at a time and use the on-screen keyboard to type the IP Address, Gateway, Netmask, DNS 1

(preferred), and DNS 2 (alternate). 5 Tap SAVE when finished. 6 Removing the touchscreen from the wall To remove the touchscreen:

1 Remove the 3/32" set screw. 2 Pull the bottom of the touchscreen away from the locking tab, then lift the screen up and off the power box. Figure 9: Lift bottom away and lift up Troubleshooting Boot up time When the device is booting up, it may take 30 seconds or longer before the Green LED turns on. When it turns on, it blinks slowly for a time and then turns off. After that, youll see an image on the touchscreen (either the setup menu or the rooms home screen). Unresponsive screen If the cameras LED blinks on and off for more than 30 seconds, the device may need to be power cycled. If power cycling doesnt solve the problem, the touchscreen may need to be restored to factory defaults. To power cycle the touchscreen:

1 Press and hold the power button for several seconds until the touchscreen turns off. 2 Press and release the power button again to turn back on. To restore to factory defaults:

1 On the touchscreens main screen, tap Settings, System Info, then Factory data reset.

- OR -

- OR -

If the touchscreen has not yet been configured, tap About, then Factory data reset. To reset without using the display screen, insert a straightened paper clip into the left pinhole on top of the touchscreen, then press and hold it while pressing the RESET

(right) pinhole button for several seconds until the the icon below appears on the display. 7 Additional resources The following resources are available for additional support. Knowledgebase and forums in Technician Community Technical Support Control4 website: www.control4.com Composer documentation in its online help. Warranty and legal notices Find details of this products 2-Year Limited Warranty at snapav.com/warranty, or request a paper copy from Customer Service at (866) 424-4489. Find other legal resources, such as regulatory notices and patent information, at snapav.com/legal. More help For the latest version of this document, open this URL or scan the QR code on a device that can view PDFs. LATEST VERSION OF THIS DOCUMENT ctrl4.co/t4-inwall-ig WALL BOX INSTALL: NEW CONSTRUCTION WALL BOX INSTALL: RETROFIT ctrl4.co/wallbox-new ctrl4.co/wallbox-retro Copyright 2020, Wirepath Home Systems, LLC. All rights reserved. Control4 and Snap AV and their respective logos are registered trademarks or trademarks of Wirepath Home Systems, LLC, dba Control4 and/or dba SnapAV in the United States and/or other countries. Snap AV and Wirepath are also registered trademarks or trademarks of Wirepath Home Systems, LLC. Other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice. B 200-00678-B 2020-10-20 MS In-Wall Touchscreen Wall Box - New Construction Installation Guide Specifications Dimensions: 68 x 104 x 81 mm (2.7 x 4.1 x 3.19") Plastic wall box model (C4-NWB57C-P) A Dovetail socket (on both sides to reverse position) B Stud plate Installing the wall box Note: This kit is intended for installation of a wall box before drywall installation. If the drywall is in place, use kits intended for retrofit (C4-

RWB57C-P or C4-RWB57C-M). For more information, visit the product pages at ctrl4.co/boxnewp and ctrl4.co/boxnewm. To install this wall box:

1 Find an appropriate wall box location for the touchscreen you are installing:

The wall box should be in a convenient location, for example, near the The wall box should be at eye level, about about 1.5meters (57 to entrance of a room. 61inches) from the floor. B A Touchscreen AC outlet (unless using PoE) Introduction This wall box kit provides a wall box (back box) to accommodate the installation of in-wall touchscreens. The kit is intended for new construction where drywall is not yet in place. Along with the wall box, the kit contains a stud plate for attachment to a wall stud before drywall installation. Supported touchscreen models C4-T4IW8-BL 8" T4 In-Wall Touchscreen, Black C4-T4IW8-WH 8" T4 In-Wall Touchscreen, White C4-T4IW10-BL 10" T4 In-Wall Touchscreen, Black C4-T4IW10-WH 10" T4 In-Wall Touchscreen, White Also supports these legacy touchscreens:

C4-WALL7 C4-WALL10 T3-7 7" In-Wall Touchscreen T3-10 10" In-Wall Touchscreen C4-TSWMC5-EG 5" In-Wall Touchscreen C4-TSWMC7-EG 7" In-Wall Touchscreen C4-TW7C0 7" In-Wall Touchscreen with Camera For more installation instructions specific to legacy touchscreens, see earlier versions of this guide. Box contents The following items are included in the kit:

In-Wall Touchscreen Wall Box - New Construction Ferrite clamps: two rectangular, one round Plastic wall boxes include two screws. Metal wall boxes include four screws

(2 short, 2 long) Tools needed Tape measure and pencil Hammer or screwdriver Nails or screws (4 to 6) A 5/16" nut driver or socket wrench (metal wall box only) Warning! Before you install the wall box, ensure that youve turned off the power to the wires that will be attached to the box. Attention ! Avant dinstaller le botier arrire, assurer vous davoir dsactiv le pouvoir sur les fils qui seront attaches la bote. Metal wall box model (C4-NWB57C-M) A Mounting location (on both sides to reverse position) B Stud plate B A 9 After you install the drywall, carefully tighten the screws to pull in the securing tabs so that the wall box is flush with the surface of the wall. Important: In the metal wall box kit, the two longer screws are for use with the T4, the shorter for use with the T3. Note: Overtightening the screws may pull the box into the wall. Important: When you are ready to install the drywall, and you are cutting the opening for the wall box, do not cut the opening too large. Be conservative and enlarge the hole as needed. Additional resources The following resources are available for additional support. Knowledgebase and forums in Technician Community Technical Support Control4 website: www.control4.com Composer documentation in its online help. Warranty and legal notices Find details of this products 2-Year Limited Warranty at snapav.com/warranty, or request a paper copy from Customer Service at (866) 424-4489. Find other legal resources, such as regulatory notices and patent information, at snapav.com/legal. For the latest version of this document, open this URL or scan the QR code on a device that can view PDFs. MOST RECENT VERSION T4 IN-WALL TOUCHSCREEN INSTALL GUIDE ctrl4.co/wallbox-new ctrl4.co/t4-inwall-ig When using Ethernet or PoE, the wall box should be near a location where an Ethernet Cat 5/6 cable is pulled. When using AC power, position the wall box above or near an AC power source, such as an AC outlet. 2 Hold the wall box and stud plate against the nearest stud, then mark the correct position according to your choices in Step 1. Follow these guidelines:

More help a Place the wall box so that, when mounted, it is flush with the surface of the drywall after the drywall is installed. For example, if the drywall is 3/8 of an inch deep, the front rim of the wall box must be 3/8 of an inch above the wall stud (toward you). Important: Make sure the wall box is flush with the wall after the drywall is installed. Allow 3/8 of an inch before the drywall is installed (depending on the thickness of the drywall), and err toward 5/16 inch for the best fit. b Install the wall box according to the arrows inside the box that indicate the correct side up. Important: For safety, install the wall box with the correct side up. c Install the wall box with the stud plate on either the right or the left side, depending on which wall stud you choose. You may detach the stud plate from the wall box on one side and reattach it on the opposite side, if needed. 3 Detach the stud plate from the wall box. Plastic box: Slide the wall plate toward the back of the wall box. Metal box: Unscrew the wall box from the stud plate. This allows you to attach the stud plate to the wall stud without interference from the wall box. 4 Align the stud plate with the marks you made on the stud (Step 2). If you are using a plastic wall box, make sure the dovetail is toward the back of the stud plate (away from you). 5 Nail or screw the stud plate to the wall stud. Recommended hardware: #9/3.5 mm wood screw or 6D/3 mm nail. 6 Mount the wall box to the stud plate. Plastic box: Slide the wall box onto the stud plate dovetail all the way, leaving the wall box protruding the depth of the drywall, or slightly less

(Step 2a). Metal box: Bolt the wall box back onto the stud plate. Note: If you are using a metal box, you can continue to adjust its angle and position slightly relative to the drywall. 7 When running cables into the wall box, use a left-side knockout for the Ethernet cable, and use a right-side knockout for the AC power (if used). Note: The left (low-voltage) and right (high-voltage) sides of the wall box are separated by a barrier. Low-voltage connections must be pulled through a knockout on the left side, and high-voltage on the right. Caution: Use only 14 AWG wire for AC connections. For supply connections, use wires suitable for at least 60 C (140 F). 8 Install the drywall as you would normally, making sure to cut the size of the hole accurately. Copyright 2020, Wirepath Home Systems, LLC. All rights reserved. Control4 and Snap AV and their respective logos are registered trademarks or trademarks of Wirepath Home Systems, LLC, dba Control4 and/or dba SnapAV in the United States and/or other countries. Snap AV and Wirepath are also registered trademarks or trademarks of Wirepath Home Systems, LLC. Other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice. J 200-00165-J 2020-10-20 MS Regulatory Compliance & Safety Information for Model C4-T4IW8-WH, C4-T4IW8-BL, C4-

T4IW10-WH, C4-T4IW10-BL Electrical Safety Advisory Scurit lectrique consultatif Important Safety Instructions Consignes de scurit importantes Read the safety instructions before using this product. Lisez les consignes de scurit avant d'utiliser ce produit. 1. Read these instructions. Lisez ces instructions. 2. Keep these instructions. Conservez ces instructions. 3. Heed all warnings. Respectez tous les avertissements. 4. Follow all instructions. Suivez toutes les instructions. 5. Do not use this apparatus near water. Ne pas utiliser cet appareil prs de l'eau. 6. Clean only with dry cloth. Nettoyez-le uniquement avec un chiffon sec. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. fabricant. Ne pas bloquer les ouvertures de ventilation. Installer conformment aux instructions du 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Ne pas installer prs de sources de chaleur telles que des radiateurs, registres de chaleur, poles, ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Ne pas contourner le dispositif de scurit de la fiche polarise ou de mise la terre. Une fiche polarise possde deux lames dont une plus large que l'autre. Une fiche de terre a deux lames et une troisime broche de terre. La lame large ou la troisime broche est fournie pour votre scurit. Si la fiche fournie ne s'adapte pas votre prise, consultez un lectricien pour le remplacement de la prise obsolte. 10. Only use attachments/accessories specified by the manufacturer. Utilisez uniquement des fixations / accessoires spcifis par le fabricant. 11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Utilisez uniquement avec le chariot, le socle, le trpied, le support ou la table spcifis par le fabricant ou vendu avec l'appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous dplacez l'ensemble chariot / appareil pour viter des blessures dues au renversement. 12. Unplug this apparatus during lightning storms or when unused for long periods of time. Dbranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilis pendant de longues priodes de temps. 13. Warning! Install this equipment in accordance with all national, state, and local electrical codes and must be completed by a certified electrician. For supply connections use 14 AWG only that is suitable for at least 600C. This equipment must be mounted at height less than or equal to 2m. This equipment may only be used with, and requires the use of, one of the following separately certified Wall-Box models, C4-NWB57C-M, C4-NWB57C-

P, C4-RWB57C-M, C4-RWB57C-P. Attention! Installez cet quipement conformment tous les codes lectriques nationaux, provinciaux et locaux et doit tre effectu par un lectricien certifi. Pour les connexions d'alimentation, utilisez uniquement 14 AWG qui convient au moins 600C. Cet quipement doit tre mont une hauteur infrieure ou gale 2 m. Cet quipement ne peut tre utilis qu'avec l'un des modles de botiers muraux certifis sparment suivants, C4-NWB57C-M, C4-NWB57C-P, C4-RWB57C-M, C4-RWB57C-P. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Confiez toutes les rparations un personnel qualifi. Une rparation est ncessaire lorsque l'appareil a t endommag de quelque faon que ce soit le cordon d'alimentation ou la fiche est endommag, du liquide a t renvers ou si des objets sont tombs dans l'appareil, l'appareil a t expos la pluie ou l'humidit, ne fonctionne pas normalement, ou s'il est tomb. 15. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. Cet quipement utilise la puissance AC qui peuvent tre soumis des surtensions lectriques, la foudre gnralement transitoires qui sont trs destructives envers les quipements terminaux connects des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causs par les surtensions lectriques ou transitoires de foudre. Pour rduire le risque de cet quipement devient endommag, il est suggr que le client envisager l'installation d'un limiteur de surtension. 16. To completely disconnect unit power from the AC mains, turn off the circuit breaker. To reconnect power, turn on the circuit breaker following all safety instructions and guidelines. The circuit breaker shall remain readily accessible. Pour dconnecter compltement l'alimentation de l'unit du secteur, dsactivez le disjoncteur. Pour rebrancher l'alimentation, activez le disjoncteur en suivant toutes les instructions et directives de scurit. Le disjoncteur doit rester facilement accessible. 17. This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. Ce produit repose sur l'installation des btiments pour les courts-circuits (surintensit) de protection. Assurez-vous que le dispositif de protection est assigne ne dpassant pas:

20A. 18. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. N'introduisez jamais d'objets d'aucune sorte dans ce produit travers les fentes du botier car ils pourraient toucher des points de tension dangereux ou court-circuiter des pices qui pourraient entraner un incendie ou un choc lectrique. 19. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and microwave ovens if placed in close proximity. Ce produit peut interfrer avec des appareils lectriques tels que les magntophones, tlviseurs, radios, ordinateurs et fours micro-ondes si placs proximit. The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product L'clair et la flche dans le triangle est un signe d'alerte pour vous avertir d'une tension dangereuse l'intrieur du produit Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Attention: Pour rduire le risque de choc lectrique, ne pas retirer le couvercle

(ou l'arrire). Aucune pice rparable par l'utilisateur. Confiez l'entretien un personnel qualifi. The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. Le point d'exclamation dans un triangle est un signe d'avertissement vous signale des instructions importantes accompagnant le produit. See marking on bottom / back of product Voir le marquage sur les bas / dos du produit Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture AVERTISSEMENT! Pour rduire le risque de choc lectrique, n'exposez pas cet appareil la pluie ou l'humidit. Save these instructions Conservez ces instructions Compliance of this equipment is confirmed by the following label that is placed on the equipment:

Conformit de cet appareil est confirm par le symbole suivant qui est plac sur l'quipement:

USA & Canada Compliance FCC Part 15, Subpart B & IC Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules and ISEDs license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la section 15 des rgles de la FCC et ISEDs aux RSS exempts de licence d'ISED. Son utilisation est soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles et (2) cet appareil doit accepter toutes les interfrences reues, y compris celles pouvant entraner un fonctionnement non souhait. IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de lutilisateur pour actionner cet quipement. Canada Warning Statement:

CAN ICES-3 (B)/NMB-3(B) This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Ce produit rpond aux spcifications techniques applicables l'innovation, Science et Dveloppement conomique Canada. FCC Part 15, Subpart C / RSS-247 Intentional Emissions Interference Statement Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment:

Notice: The term FCC ID: and IC: before the certification number signifies that FCC and Industry Canada technical specifications were met. FCC ID: 2AJACT4TS IC: 7848A-T4TS This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-247, Antenna Requirements. Do not use any antenna other than the one provided with the unit. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Caution :

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and

(iii) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et lexploitation non point point, selon le cas;

(iii) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. FCC Partie 15, sous-partie C / RSS-247 Dclaration volontaire des missions interfrences Conformit de cet appareil est confirm par les chiffres de certification suivants qui sont placs sur l'quipement:

Avis: Le terme FCC ID:" et "IC:" devant le numro de certification signifie que les spcifications techniques de la FCC et d'Industrie Canada ont t respectes. FCC ID: 2AJACT4TS IC: 7848A-T4TS Cet quipement doit tre install par des professionnels qualifis ou entrepreneurs conformment aux normes FCC partie 15.203 & IC RSS-247, Exigences d'antenne. Ne pas utiliser une antenne autre que celui fourni avec l'appareil. Cet metteur ne doit pas tre localis ou fonctionner avec d'autres antennes ou transmetteurs. Les oprations dans la bande 5.15-5.25GHz sont limites l'utilisation l'intrieur seulement. RF Radiation Exposure Statement This equipment complies with FCC RF and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons. Dclaration d'exposition aux radiations RF Cet quipement est conforme aux limites d'exposition aux rayonnements RF et IC de la FCC dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 centimtres entre le radiateur et votre corps ou des personnes proches. Europe Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. The full text of the EU Declaration of Conformity (DoC) is available on the regulatory webpage:

This product can be put into service in all of the EU member states, European Free Trade Association

(EFTA) and EU candidate countries without any restriction. BG EE FR LV BE CZ DE IE ES HR CY LT HU MT NL PT RO PL FI SK SE NO LI IS MK AL RS DK EL IT LU AT SI UK CH TR The frequency and maximum transmitted power in EU are listed as below:

2412 - 2472 MHz: +15 dBm 5180 - 5240 MHz: +17 dBm WLAN 5GHz:

Operations in the 5.15-5.35GHz band are restricted to indoor usage only. Recycling Wirepath Home Systems, LLC understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions. WEEE Compliance Wirepath Home Systems, LLC is committed to meeting all requirements of the Waste Electrical and Electronic Equipment (WEEE) directive (2012/19/EC). The WEEE directive requires the manufacturers of electrical and electronic equipment who sell in EU countries: (1) label their equipment to notify customers that it needs to be recycled, and (2) provide a way for their products to be appropriately disposed of or recycled at the end of their product lifespan. For collection or recycling of Wirepath Home Systems, LLC products, please contact your local Wirepath Home Systems, LLC representative or dealer. Australia & New Zealand Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. About this Document Copyright 2020 Wirepath Home Systems, LLC All rights reserved.

Wi-Fi Limited Module Integration Instructions Model: 040-00460a This module has been granted limited modular approval for use in the C4-T4 Series of Automation Controllers. This device is for internal use only and is NOT sold to 3rd parties. Use of this device on products other than those listed below will require additional certifications. The host product with the module installed must be evaluated for simultaneous transmission requirements. The user manual for the host product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC/IC RF exposure guidelines. The Module must only be used in the following device and antenna combinations C4-T4IW8-XX*

DEVICE C4-T4IW10-XX*

ANTENNA PORT Antenna 0 Antenna 1 Antenna 0 Antenna 1 Antenna 0 Antenna 1 Antenna 0 Antenna 1

- XX is a unit color identifier (Black or White) C4-T4T10-XX*

C4-T4T8-XX*

ANTENNA MODEL 1005097 1005098 1005095 1005096 1005180 1005179 1005178 1005179 A label must be affixed to the outside of the host product with the following statements:

Contains FCC ID: 2AJACT4TS Contains IC: 7848A-T4TS The final host/module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. If the final host/module combination is intended for use as a portable device (see classifications below) the host manufacturer is responsible for separate approvals for the SAR requirements from FCC Part 2.1093 and RSS-102. The module incorporates a MuRata radio module with a single transciever output that connects to an RF switch for diversity. The switch drives two MHF 4L coaxial sockets to which a the antennas can be attached. 1 Signal and power connector Connect signal and power through Novastack 35-P board connector details:

I-PEX Connectors: 20709-050E-01 0 CONN, 50PIN PLUS 2 POWER RECEPTACLE 0.7MM HEIGHT 0.35MM PITCH Drawing:

Reference A B C D E F 8.40 9.42 10.92 10.75 9.70 11.10 Dimension in mm 2 Receptacle pinout:

Device classifications Since host devices vary widely with design features and configurations, module integrators shall follow the guidelines below regarding device classification and simultaneous transmission and seek guidance from their preferred regulatory test lab to determine how regulatory guidelines will impact the device compliance. Proactive management of the regulatory process will minimize unexpected schedule delays and costs due to unplanned testing activities. The module integrator must determine the minimum distance required between their host device and the users body. The FCC provides device classification definitions to assist in making the correct determination. Note that these classifications are guidelines only; strict adherence to a device classification may not satisfy the regulatory requirement as near-body device design details may vary widely. Your preferred test lab will be able to assist in determining the appropriate device category for your host product and if a KDB or PBA must be submitted to the FCC. Note: The module you are using has been granted modular approval for mobile applications. Portable applications may require further RF exposure (SAR) evaluations. It is also likely that the host/module combination will need to undergo testing for FCC Part 15 regardless of the device classification. Your preferred test lab will be able to assist in determining the exact tests which are required on the host/module combination. FCC definitions Portable: (2.1093) A portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is/are within 20 centimeters of the body of the user. 3 Mobile: (2.1091) (b) A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitters radiating structure(s) and the body of the user or nearby persons. Per 2.1091d(d)(4) In some cases (for example, modular or desktop transmitters), the potential conditions of use of a device may not allow easy classification of that device as either Mobile or Portable. In these cases, applicants are responsible for determining minimum distances for compliance for the intended use and installation of the device based on evaluation of either specific absorption rate (SAR), field strength, or power density, whichever is most appropriate. Simultaneous transmission evaluation This module has not been evaluated or approved for simultaneous transmission as it is impossible to determine the exact multi-transmission scenario that a host manufacturer may choose. Any simultaneous transmission condition established through module integration into a host product must be evaluated per the requirements in KDB447498D01(8) and KDB616217D01,D03 (for laptop, notebook, netbook, and tablet applications). These requirements include, but are not limited to:

Transmitters and modules certified for mobile or portable exposure conditions can be incorporated in mobile host devices without further testing or certification when:

The closest separation among all simultaneous transmitting antennas is >20 cm, Antenna separation distance and MPE compliance requirements for ALL simultaneous transmitting antennas have been specified in the application filing of at least one of the certified transmitters within the host device. In addition, when transmitters certified for portable use are incorporated in a mobile host device, the antenna(s) must be >5 cm from all other simultaneous transmitting antennas. All antennas in the final product must be at least 20 cm from users and nearby persons. Or FCC statements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la section 15 des rglementations de la FCC. Le fonctionnement de lappareil est sujetaux deux conditions suivantes :

1) cet appareil ne doit pas provoquer dinterfrences nfastes, et 2) cet appareil doit tolrer les interfrences reues, y compris celles qui risquent de provoquer unfonctionnement indsirable. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 4 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. FCC Radiation Exposure Statement FCC Modular Usage Statement Note 1: This module certified complies with RF exposure requirements under mobile or fixed condition; this module is to be installed only in mobile or fixed applications. A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structure(s) and the body of the user or nearby persons. Transmitting devices designed to be used by consumers or workers that can be easily re-located, such as wireless devices associated with a personal computer, are considered to be mobile devices if they meet the 20 centimeter separation requirement. A fixed device is defined as a device is physically secured at one location and is not able to be easily moved to another location. Note 2: Host product manufacturers must provide in their user manual the required RF exposure information for mobile & fixed usage of this module. Host product manufacturers must use the following RF exposure statement in their user manual This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and all persons. This transmitter must not be co-location or operating in conjunction with any other antenna or transmitter. Note 3: To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. For example, if a host was previously authorized as an unintentional radiator under the Suppliers Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the part 15B unintentional radiator requirements. Since this may depend on the details of how the module is integrated with the host, the manufacturer shall provide guidance to the host manufacturer for compliance with the part 15B requirements. ISED Statements This device complies with Innovation, Science and Economic Development Canadas licenseexempt RSS standard(s). Operation is subject to the following two conditions:

1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :

1) l'appareil ne doit pas produire de brouillage, et 2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. ISED RF Exposure Statement This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 5 Le rayonnement de la classe b repecte ISED fixaient un environnement non contrls.Installation et mise en oeuvre de ce matriel devrait avec changeur distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec dautres. ISED Modular Usage Statement NOTE 1: When the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use the wording Contains transmitter module IC: 7848A-T4TS or Contains IC:

7848A-T4TS. NOTE 1: Lorsque le numro de certification ISED n'est pas visible lorsque le module est install dans un autre appareil, l'extrieur de l'appareil dans lequel le module est install doit galement afficher une tiquette faisant rfrence au module inclus. Cette tiquette extrieure peut tre libelle Contient le module metteur IC: 7848A-

T4TS ou Contient IC:

7848A-T4TS. Copyright 2020, Wirepath Home Systems, LLC. All rights reserved. Control4 and Snap AV and their respective logos are registered trademarks or trademarks of Wirepath Home Systems, LLC, dba Control4 and/or dba SnapAV in the United States and/or other countries. Snap AV and Wirepath are also registered trademarks or trademarks of Wirepath Home Systems, LLC. Other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice. 2020-09-02 MS 6

C4-T4 series devices Label Samples and Locations Figure 1: C4-T4IW8 Label Sample Figure 2: C4-T4IW8 Label Location Figure 3: C4-T4IW10 Label Sample Figure 4: C4-T4IW10 Label Location Figure 5: C4-T4T8 Label Sample Figure 6: C4-T4T8 Label Location Figure 7: C4-T4T10 Label Sample Figure 8: C4-T4T10 Label Location

November 10, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2AJACT4TS To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Parts List Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. Best Regards Roger Midgley Principal Compliance Engineer Wirepath Home Systems LLC. dba SnapAV, dba Control4 11734 South Election Road, Ste. 200 | Salt Lake City, Utah 84020 | www.control4.com | 801.523.3100 phone |

FCC LIMITED MODULAR APPROVAL REQUEST (per Part 15.212 / KDB 996369 D01) FCC ID: 2AJACT4TS ITEMS TO BE COVERED ANSWER FROM APPLICANT Yes, Refer to photo exhibit 1. The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield but must be on the module assembly. 2. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal;

module;

4. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b);

5. The module must demonstrate compliance in a standalone configuration;

3. The module must contain power supply regulation on the Yes, refer to schematics exhibits Yes, refer to schematics exhibits Yes, refer to photo exhibit NO:

The gain of the antennas used is dependent on placement in the product chassis, and as such, the module was tested in the configurations installed in the intended products. This module is limited for use in the C4-T4 series devices manufactured by Wirepath Home Systems, and not sold to 3rd parties. Yes, refer to label sample exhibit Yes, refer to operational descriptions and test reports exhibits 6. The module must be labeled with its permanently affixed FCC ID label, or use an electronic display (see KDB Publication 784748);

7. The module must comply with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee;

8. The module must comply with RF exposure requirements (see Yes, refer to MPE exhibit Clause V below). Name of Applicant (or Authorized Representative):Jason Stewart, Director Laboratories, VPI Laboratories Date: 12/22/2020 Signature:

Authority to Act as Agent FCC November 11, 2020 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AJACT4TS To Whom It May Concern:

We, the undersigned, hereby authorize Jason Stewart of VPI Laboratories at 313 W. 12800 S,. Suite 311, Draper UT 84020 to act as our agent and on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by VPI Laboratories on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards,

(Signature) Roger Midgley By:

Title:

On behalf of: Wirepath Home Systems LLC. dba SnapAV, dba Control4 Principal Compliance Engineer

(Company Name)

(Print name) 11734 South Election Road | Draper, Utah 84020 | www.control4.com | 801.523.3100 phone | 801.523.3199 fax