FCC ID: 2AJACWIFIMOD System Controller

Wi-Fi Module Integration Instructions Model: 040-00460 This module has been granted modular approval for mobile applications. OEM integrators for host products may use the module in their final products without additional FCC/IC (Industry Canada) certification if they meet the following conditions. Otherwise, additional FCC/IC approvals must be obtained. The host product with the module installed must be evaluated for simultaneous transmission requirements. The user manual for the host product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC/IC RF exposure guidelines. To comply with FCC/IC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only exposure condition must not exceed 2dBi. The antenna used must be equivalent to the following:

Manufacturer: ACON, Advanced-Connectek Inc. Manf. part number:

ACON_ADEEE-000000 Type: Swivel dipole, reverse SMA Frequency range:

2.4 GHz - 2.5 GHz 5.15 GHz - 5.85 GHz Impedance: 50 VSWR: 1.92:1 max. Return loss: -10 dB Gain (peak): 2.0 dBi Cable attachment:

MHF 4L Plug to RSMA. 50 RG-178,

< 10 inches in length, low loss up to 6 GHz A label must be affixed to the outside of the host product with the following statements:

Contains FCC ID: 2AJACWIFIMOD Contains IC: 7848A-WIFIMOD 1 The final host/module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. If the final host/module combination is intended for use as a portable device (see classifications below) the host manufacturer is responsible for separate approvals for the SAR requirements from FCC Part 2.1093 and RSS-102. The module incorporates a MuRata radio module with a single transciever output that connects to an RF switch for diversity. The switch drives two MHF 4L coaxial sockets to which a dipole antenna can be attached. Signal and power connector I-PEX Connectors: 20709-050E-01 0 Connect signal and power through Novastack 35-P board connector details:

CONN, 50PIN PLUS 2 POWER RECEPTACLE 0.7MM HEIGHT 0.35MM PITCH 2 Drawing:

Reference A B C D E F Dimension in mm 8.40 9.42 10.92 10.75 9.70 11.10 3 Receptacle pinout:

Device classifications Since host devices vary widely with design features and configurations, module integrators shall follow the guidelines below regarding device classification and simultaneous transmission and seek guidance from their preferred regulatory test lab to determine how regulatory guidelines will impact the device compliance. Proactive management of the regulatory process will minimize unexpected schedule delays and costs due to unplanned testing activities. The module integrator must determine the minimum distance required between their host device and the users body. The FCC provides device classification definitions to assist in making the correct determination. Note that these classifications are guidelines only; strict adherence to a device classification may not satisfy the regulatory requirement as near-body device design details may vary widely. Your preferred test lab will be able to assist in determining the appropriate device category for your host product and if a KDB or PBA must be submitted to the FCC. Note: The module you are using has been granted modular approval for mobile applications. Portable applications may require further RF exposure (SAR) evaluations. It is also likely that the host/module combination will need to undergo testing for FCC Part 15 regardless of the device classification. Your preferred test lab will be able to assist in determining the exact tests which are required on the host/module combination. 4 FCC definitions Portable: (2.1093) A portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is/are within 20 centimeters of the body of the user. Mobile: (2.1091) (b) A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitters radiating structure(s) and the body of the user or nearby persons. Per 2.1091d(d)(4) In some cases

(for example, modular or desktop transmitters), the potential conditions of use of a device may not allow easy classification of that device as either Mobile or Portable. In these cases, applicants are responsible for determining minimum distances for compliance for the intended use and installation of the device based on evaluation of either specific absorption rate (SAR), field strength, or power density, whichever is most appropriate. Simultaneous transmission evaluation This module has not been evaluated or approved for simultaneous transmission as it is impossible to determine the exact multi-transmission scenario that a host manufacturer may choose. Any simultaneous transmission condition established through module integration into a host product must be evaluated per the requirements in KDB447498D01(8) and KDB616217D01,D03 (for laptop, notebook, netbook, and tablet applications). These requirements include, but are not limited to:

Transmitters and modules certified for mobile or portable exposure conditions can be incorporated in mobile host devices without further testing or certification when:

The closest separation among all simultaneous transmitting antennas is >20 cm, Or persons. Antenna separation distance and MPE compliance requirements for ALL simultaneous transmitting antennas have been specified in the application filing of at least one of the certified transmitters within the host device. In addition, when transmitters certified for portable use are incorporated in a mobile host device, the antenna(s) must be >5 cm from all other simultaneous transmitting antennas. All antennas in the final product must be at least 20 cm from users and nearby FCC statements This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. 5 Cet appareil est conforme la section 15 des rglementations de la FCC. Le fonctionnement de lappareil est sujetaux deux conditions suivantes :

1) cet appareil ne doit pas provoquer dinterfrences nfastes, et 2) cet appareil doit tolrer les interfrences reues, y compris celles qui risquent de provoquer unfonctionnement indsirable. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. FCC Modular Usage Statement Note 1: This module certified complies with RF exposure requirements under mobile or fixed condition; this module is to be installed only in mobile or fixed applications. A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structure(s) and the body of the user or nearby persons. Transmitting devices designed to be used by consumers or workers that can be easily re-located, such as wireless devices associated with a personal computer, are considered to be mobile devices if they meet the 20 centimeter separation requirement. A fixed device is defined as a device is physically secured at one location and is not able to be easily moved to another location. Note 2: Host product manufacturers must provide in their user manual the required RF exposure information for mobile & fixed usage of this module. Host product manufacturers must use the following RF exposure statement in their user manual This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and all persons. This transmitter must not be co-location or operating in conjunction with any other antenna or transmitter. Note 3: To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. For example, if a host was previously authorized as an unintentional radiator under the Suppliers Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the part 15B unintentional radiator requirements. Since this may depend on the details of how the module is integrated with the host, the manufacturer shall provide guidance to the host manufacturer for compliance with the part 15B requirements. ISED Statements This device complies with Innovation, Science and Economic Development Canadas license-

exempt RSS standard(s). Operation is subject to the following two conditions:

1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. 6 Le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radioexempts de licence. L'exploitation est autorise aux deux conditions suivantes :

1) l'appareil ne doit pas produire de brouillage, et 2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. ISED RF Exposure Statement This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le rayonnement de la classe b repecte ISED fixaient un environnement non contrls.Installation et mise en oeuvre de ce matriel devrait avec changeur distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec dautres. ISED Modular Usage Statement NOTE 1: When the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use the wording Contains transmitter module IC: 7848A-WIFIMOD or Contains IC: 7848A-WIFIMOD. NOTE 1: Lorsque le numro de certification ISED n'est pas visible lorsque le module est install dans un autre appareil, l'extrieur de l'appareil dans lequel le module est install doit galement afficher une tiquette faisant rfrence au module inclus. Cette tiquette extrieure peut tre libelle Contient le module metteur IC: 7848A-WIFIMOD ou Contient IC:

7848A-WIFIMOD. Copyright 2020, Wirepath Home Systems, LLC. All rights reserved. Control4 and Snap AV and their respective logos are registered trademarks or trademarks of Wirepath Home Systems, LLC, dba Control4 and/or dba SnapAV in the United States and/or other countries. Snap AV and Wirepath are also registered trademarks or trademarks of Wirepath Home Systems, LLC. Other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice. 2020-09-02 MS 7

Request for Confidentiality 2AJACWIFIMOD September 16, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:

FCC ID:

To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Parts List Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. Best Regards Roger Midgley Principal Compliance Engineer Wirepath Home Systems, LLC. dba SnapAV 11734 South Election Road, Ste. 200 | Salt Lake City, Utah 84020 | www.control4.com | 801.523.3100 phone | 801.523.3199 fax

FCC MODULAR APPROVAL REQUEST (per Part 15.212 / KDB 996369 D01) FCC ID: 2AJACWIFIMOD ITEMS TO BE COVERED ANSWER FROM APPLICANT Yes, Refer to photo exhibit 3. The module must contain power supply regulation on the Yes, refer to schematics exhibits 1. The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield but must be on the module assembly. 2. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal;

module;

4. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b);

configuration;

6. The module must be labeled with its permanently affixed FCC ID label, or use an electronic display (see KDB Publication 784748);

7. The module must comply with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee;

Yes, refer to schematics exhibits Yes, refer to photo exhibit Yes, refer to label sample exhibit Yes, refer to operational descriptions and test reports exhibits 5. The module must demonstrate compliance in a stand-alone Yes, refer to test reports exhibits 8. The module must comply with RF exposure requirements (see Yes, refer to MPE exhibit Clause V below). Name of Applicant (or Authorized Representative):Jason Stewart, Director Laboratories, VPI Laboratories Date: 10/08/2020 Signature:

Authority to Act as Agent FCC August 18, 2020 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC Application for FCC ID: 2AJACWIFIMOD To Whom It May Concern:

We, the undersigned, hereby authorize Jason Stewart of VPI Laboratories at 313 W. 12800 S,. Suite 311, Draper UT 84020 to act as our agent and on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by VPI Laboratories on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards,

(Must be signed by the person that is listed on the FCC Website)

(Signature)

(Print name) Principal Compliance Engineer Roger Midgley By:

Title:

On behalf of: Wirepath Home Systems, LLC. dba SnapAV

(Company Name) 11734 South Election Road | Draper, Utah 84020 | www.control4.com | 801.523.3100 phone | 801.523.3199 fax