FCC ID: 2AJACAN530APIAC WAVE 2 AC WIRELESS ACCESS POINT

WAVE 2 AC WIRELESS ACCESS POINT Quick Start Guide AN-530-AP-I-AC Regulatory Compliance & Safety Information for Model AN-530-AP-I-AC Electrical Safety Advisory Scurit lectrique consultatif Important Safety Instructions Consignes de scurit importantes Read the safety instructions before using this product. Lisez les consignes de scurit avant d'utiliser ce produit. 1. Read these instructions. Lisez ces instructions. 2. Keep these instructions. Conservez ces instructions. 3. Heed all warnings. Respectez tous les avertissements. 4. Follow all instructions. Suivez toutes les instructions. 2 5. Do not use this apparatus near water. Ne pas utiliser cet appareil prs de l'eau. 6. Clean only with dry cloth. Nettoyez-le uniquement avec un chiffon sec. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. Ne pas bloquer les ouvertures de ventilation. Installer conformment aux instructions du fabricant. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Ne pas installer prs de sources de chaleur telles que des radiateurs, registres de chaleur, poles, ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Ne pas contourner le dispositif de scurit de la fiche polarise ou de mise la terre. Une fiche polarise possde deux lames dont une plus large que l'autre. Une fiche de terre a deux lames et une troisime broche de terre. La lame large ou la troisime broche est fournie pour votre scurit. Si la fiche fournie ne s'adapte pas votre prise, consultez un lectricien pour le remplacement de la prise obsolte. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Protgez le cordon d'alimentation ne soit pitin ou pinc, en particulier au niveau des fiches, des prises et au point o il sort de l'appareil. 3 11. Only use attachments/accessories specified by the manufacturer. Utilisez uniquement des fixations / accessoires spcifis par le fabricant. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Utilisez uniquement avec le chariot, le socle, le trpied, le support ou la table spcifis par le fabricant ou vendu avec l'appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous dplacez l'ensemble chariot / appareil pour viter des blessures dues au renversement. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. Dbranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilis pendant de longues priodes de temps. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Confiez toutes les rparations un personnel qualifi. Une rparation est ncessaire lorsque l'appareil a t endommag de quelque faon que ce soit le cordon d'alimentation ou la fiche est endommag, du liquide a t renvers ou si des objets sont tombs dans l'appareil, l'appareil a t expos la pluie ou l'humidit, ne fonctionne pas normalement, ou s'il est tomb. 15. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. Cet quipement utilise la puissance AC qui peuvent tre soumis des surtensions lectriques, la foudre 4 gnralement transitoires qui sont trs destructives envers les quipements terminaux connects des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causs par les surten-

sions lectriques ou transitoires de foudre. Pour rduire le risque de cet quipement devient endommag, il est suggr que le client envisager l'installation d'un limiteur de surtension. 16. To completely disconnect unit power from the AC mains, remove the power cord from the appliance coupler and/or turn off the circuit breaker. To reconnect power, turn on the circuit breaker follow-

ing all safety instructions and guidelines. The circuit breaker shall remain readily accessible. Pour dbrancher compltement l'alimentation secteur du rseau secteur, retirez le cordon d'alimentation du coupleur de l'appareil et / ou teignez le disjoncteur. Pour reconnecter l'alimentation, allumez le disjoncteur en suivant toutes les consignes et consignes de scurit. Le disjoncteur doit tre facilement accessible. 17. This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. Ce produit repose sur l'installation des btiments pour les courts-circuits (surintensit) de protection. Assurez-vous que le dispositif de protection est assigne ne dpassant pas: 20A. 18. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines. Do not open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above54 C or 130 F. ATTENTION: Comme avec toutes les batteries, il ya un risque d'explosion ou de blessure si la batterie est remplace par un type incorrect. liminez les batteries usages selon les instructions du fabricant de la batterie et applicables des directives environnementales. Ne pas ouvrir, percer ou incinrer la batterie, ou de l'exposer des matriaux conducteurs, de l'humidit, du liquide, un incendie ou une temprature suprieure 54 C ou 130 F. 19. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. 5 N'introduisez jamais d'objets d'aucune sorte dans ce produit travers les fentes du botier car ils pourraient toucher des points de tension dangereux ou court-circuiter des pices qui pourraient entraner un incendie ou un choc lectrique. 20. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and microwave ovens if placed in close proximity. Ce produit peut interfrer avec des appareils lectriques tels que les magntophones, tlviseurs, radios, ordinateurs et fours micro-ondes si placs proximit. 21. PoE considered a Network Environment 0 per IEC TR62101, and thus the interconnected ITE circuits may be considered ES1. The installation instructions clearly state that the ITE is to be connected only to PoE networks without routing to the outside plant. PoE considr comme un environnement de rseau 0 selon IEC TR62101 et, par consquent, les circuits ITE interconnects peuvent tre considrs comme ES1. Les instructions d'installation indiquent clairement que l'ITE doit tre connect uniquement aux rseaux PoE sans acheminement vers l'installation externe. 22. CAUTION: The Optical Transceiver used with this product should use UL listed, and Rated Laser Class I, 3.3 Vdc. ATTENTION: L'metteur-rcepteur optique utilis avec ce produit doit utiliser la liste UL et la classe de laser nominale I, 3,3 Vcc. 6 alerting The lightning flash and arrow head within the triangle is a warning sign the product Lclair et la flche dans le triangle est un signe dalerte pour vous avertir dune tension dangereuse lintrieur du produit. you of dangerous voltage inside Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Attention: Pour rduire le risque de choc lectrique, ne pas retirer le couvercle

(ou larrire). Aucune pice rparable par lutilisateur. Confiez lentretien un personnel qualifi. sign The exclamation point within alerting you of the product. Le point dexclamation dans un triangle est un signe davertissement vous signale des instructions importantes accompagnant le produit. instructions accompanying is a warning important triangle the See marking on bottom / back of product. Voir le marquage sur les bas / dos du produit. 7 Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture. AVERTISSEMENT! Pour rduire le risque de choc lectrique, n'exposez pas cet appareil la pluie ou l'humidit. Save these instructions. Conservez ces instructions. The AN-530-AP-I-AC uses the following power inputs: DC IN: 12V

, 2A PoE+ IN: 48V

, 0.53A 8 9 USA & Canada Compliance FCC Part 15, Subpart B & IC Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC rules and ISEDs license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la section 15 des rgles de la FCC et ISEDs aux RSS exempts de licence d'ISED. Son utilisation est soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles et (2) cet appareil doit accepter toutes les interfrences reues, y compris celles pouvant entraner un fonctionnement non souhait. 10 IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressment approuvs par la partie responsable de la conformit ont pu vider lautorit de lutilisateur pour actionner cet quipement. Canada Warning Statement:

CAN ICES-3 (B)/NMB-3(B) This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. Ce produit rpond aux spcifications techniques applicables l'innovation, Science et Dvel oppement conomique Canada. FCC Part 15, Subpart C / RSS-247 Intentional Emissions Interference Statement Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment:

Notice: The term FCC ID: and IC: before the certification number signifies that FCC and Industry Canada technical specifications were met. FCC ID: 2AJACAN530APIAC IC: 7848A-AN530APIAC 11 This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 &

IC RSS-247, Antenna Requirements. Do not use any antenna other than the one provided with the unit. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. Caution:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate;

and

(iii) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

(ii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et lexploitation non point point, selon le cas;

12

(iii) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. FCC Partie 15, sous-partie C / RSS-247 Dclaration volontaire des missions interfrences Conformit de cet appareil est confirm par les chiffres de certification suivants qui sont placs sur l'quipement:

Avis: Le terme FCC ID:" et "IC:" devant le numro de certification signifie que les spcifications techniques de la FCC et d'Industrie Canada ont t respectes. FCC ID: 2AJACAN530APIAC IC: 7848A-AN530APIAC Cet quipement doit tre install par des professionnels qualifis ou entrepreneurs conformment aux normes FCC partie 15.203 & IC RSS-247, Exigences d'antenne. Ne pas utiliser une antenne autre que celui fourni avec l'appareil. Cet metteur ne doit pas tre localis ou fonctionner avec d'autres antennes ou transmetteurs. Les oprations dans la bande 5.15-5.25GHz sont limites l'utilisation l'intrieur seulement. RF Radiation Exposure Statement This equipment complies with FCC RF and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator 13 and your body or nearby persons. Dclaration d'exposition aux radiations RF Cet quipement est conforme aux limites d'exposition aux rayonnements RF et IC de la FCC dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 centimtres entre le radiateur et votre corps ou des personnes proches. Europe Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. The full text of the EU Declaration of Conformity (DoC) is available on the regulatory webpage:

This equipment complies with CE radiation exposure requirement set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This product can be put into service in all of the EU member states, European Free Trade Association (EFTA) and EU candidate countries without any restriction This product can be put into service in all of the EU member states, European Free Trade Association (EFTA) and 14 EU candidate countries without any restriction. AT EE IT PT BE FI LV RO BG FR LT SK HR DE LU SI CY EL MT ES CZ HU NL SE DK IE PL UK The frequency and maximum transmitted power in EU are listed as below:

AN-530-AP-I-AC 2412 - 2472 MHz: 17dBm 5180 - 5240 MHz: 18.5dBm Operations in the 5.15-5.35GHz band are restricted to indoor usage only. Recycling Wirepath Home Systems, LLC understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions. 15 Welcome to Araknis Networks Thank you for choosing an Araknis Tri-Band Mesh Enabled Wireless Access Point (WAP). With improved thermal performance by way of a die-cast aluminum bottom and a tried and true mounting system, this tri-band mesh enabled access point has the versatility to maintain performance in both wireless and wired installs for home and commercial applications. AN-530-AP-I-AC Features Sleek Circular Design Unobtrusive Recessed Lighting 1 x Gigabit LAN Port (w/802.3at PoE-IN) 1 x Gigabit LAN Port (data only) Mesh Enabled Multi-User MIMO 2x2 Tri-Band Wave 2-AC 2200Mbps OvrC Enabled 16 Step 1: Unbox Wireless Access Point Mounting Bracket Tile Ceiling Backing Plate Quick Start Guide

(WAP)*

Male-to-Female Tile Ceiling Drywall Category Jumper Cable Mounting Hardware Mounting Hardware Wood Surface Mounting Hardware 17 Step 2: Install A Ceiling Mount B Shelf Mount C In-Ceiling Mount Accessory not included D Wall Mount NOTE: Use the ceiling back plate on top of acoustic ceiling tiles to prevent the mounting nuts from pulling through. 18 Position the Ceiling Mount Ceiling Tiles WAP Tile Ceiling Backing Plate Ceiling Mount Center Line*

Position 1 First Position Second Position

* Center line of the bracket is not necessarily the center line of the WAP when installed. Please use the guide above to understand the center line of the WAP when installing the bracket. Center Line*

Position 2 19 Step 3: Connect Internet PoE Switch WAP LAN WAN Router LAN WAN Router LAN WAN Router POWER + DATA (OUT) AN-ACC-INJ-30W DC 48V Input Power DATA (IN) AN-310-SW-F-8-POE AN-310-SW-F-8-POE AN-310-SW-F-8-POE Internet Switch PoE Injector

(not included) WAP Internet Switch WAP DC Power Supply

(not included) 20 Step 4: Verify LED*

LED*

*NOTE: The LED is located on the side of the device. LED Status:

Blinking White: Powering on. Solid White: Ready for setup. Solid Blue: Controller/Node connected to Internet. Blinking/Solid Red: Wireless backhaul lost or unit locked up. For a full list of LED behaviors, please see link. 21 Step 5: Log Into Web Interface A Log in using the default credentials:

Username Password araknis araknis NOTE: If you cant connect to the WAP using this method, or need to configure the device before connecting it to the network, try these options for accessing your device:

DHCP IP address Page 15 Default IP Address Page 16 OvrC Page 19 22 Pro Tip: Save and Apply Changes After making changes to settings on a menu page, click the Save button on the menu to hold the new settings in the Apply Changes field. After all desired changes have been made, click Apply Changes to review the new settings if any. Click "Apply" to make the changes or "Revert" to cancel the changes. NOTE: Settings will take affect after the progress bar completes 100%. 23 Other Access Methods: DHCP IP Address The WAP is configured to DHCP by default so that the DHCP server can assign an IP address when the WAP is connected to the network (the DHCP server is usually the router). This address can be used for accessing the web interface. Check the client table on your router to find the IP address of the WAP. 24 Other Access Methods: Default IP Address If the WAP is not issued an IP address on the network, or needs to be accessed while not connected to a network, you can configure your computer's network connection to allow access using the default IP address, 192.168.20.253. Windows 7 screenshots shown for reference. A Connect your PC to the WAP using a network patch cable. B On your PC, open the Control Panel and left-click Network and Internet. C Left-click Network and Sharing Center. Computer WAP 25 Other Access Methods: Default IP Address Windows 7 screenshots shown for reference. D In the left bar, left-click Change adapter settings. E Right-click the icon for the wired network connection and left-click "Properties". F Left-click to highlight Internet Protocol Version 4 (TCP/IPv4), then left-click Properties. 26 Other Access Methods: Default IP Address Windows 7 screenshots shown for reference. G In the General tab, left-click

"Use the following IP address:"

and enter the IP address and subnet mask. H Left-click OK to close Internet Protocol Version 4 (TCP/IPv4) Properties, then left-click "OK"

to close wireless network connection properties. I Open a browser and navigate to http://192.168.20.253/. Log in using the default credentials:

Username araknis Password araknis IP Address 192.168.20.2 Subnet Mask 255.255.255.0 27 Other Access Methods: OvrC OvrC gives you remote device management, real-time notifications, and intuitive customer management, right from your computer or mobile device. Setup is plug-and-play, with no port forwarding or DDNS address required. To add this device to your OvrC account:

Add the Device (MAC address and Service Tag numbers needed for authentication) A Connect the WAP to the Internet Log Into OvrC (www.ovrc.com) B C Web Browser Access Internet LAN WAN 1 2 3 4 5 6 7 8 1 Gbps Link/Act AN-110-SW-R-8 Mobile Apps OvrC Server 28 Contacting Technical Support P

(866) 838-5052 E techsupport@snapav.com 2-Year Limited Warranty Find details of this product's 2-Year Limited Warranty at snapav.com/warranty, or request a paper copy from Customer Service at (866) 424-4489. Find other legal resources, such as regulatory notices and patent information, at snapav. com/legal. US local representative information:

Company: Wirepath Home Systems LLC Address: 1800 Continental Blvd. Suite 200, Charlotte, NC 28273 USA Tel: 704.927.7620 Fax: 800.782.2410 Copyright 2020, Wirepath Home Systems, LLC. All rights reserved.Control4 and Snap AV and their respective logos are registered trademarks or trademarks of Wirepath Home Systems, LLC, dba Control4 and/or dba SnapAV in the United States and/or other countries. Snap AV, Araknis, and Wirepath are also registered trademarks or trademarks ofWirepath Home Systems, LLC. Other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice. 201112-1731

Model name:

AN-530-AP-I-AC DC IN: 12V ==, 24 PoE+ IN: 48V === 0.53A FCC ID: 2AJACANS30APIAC IC : 7848A-ANS30APIAC CAN ICES-3 (B)/NMB-3(B)

$T0000000000 MAC:

90:A7:C1:03:27:F2 GE) FE This device complies with part 15 of the FCC Rules. Operation is subject to the CERTIFIED following two conditions. (1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operations. araknisnetworks.com Made in Taiwan ANSSSO-APA-AC ium mt ii i a WN Ge FE

Wirepath Home Systems, LLC, DBA SnapAV 1800 Continental Blvd Suite 200, Charlotte, North Carolina 28273 USA August 18, 2020 UNII Device Declaration Letter To whom it may concern :

We have declared below featured for FCC equipment authorization, Device FCC ID : 2AJACAN530APIAC

(1) DFS Device --

Master , Client without radar detection capability , Client with Radar detection capability , N/A

(2) Active / Passive Scanning , adhoc mode access point capability Frequency Band

(MHz) Active Scanning

(the device can transmit a probe passive scanning

(where the device is can listen only with no Ad Hoc Mode capability Access point capability 5150~5250 5725~5850 No No

(beacon)) Yes , Yes , No No probes) Yes , Yes , No No Yes , Yes , No No Yes , Yes ,

(3) Country code selection ability -

Yes , No If no, pls explain how it was implemented : Since the user is unable to modify the country code, the device can only operate within its authorization is the U.S.

(4) Meet 15.202 requirement -

Yes , No , pls check below :

A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-

DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes can not be modified by end user or an installer. Apply , No Apply , (If apply , pls help to provide explanation on it was implement , and how software was controlled) Name/Title: Roger Midgley/ Principle Compliance Engineer Company Name: Wirepath Home Systems, LLC, DBA SnapAV Address: 1800 Continental Blvd Suite 200, Charlotte, North Carolina 28273 USA TEL: +18015233187 FAX: +18015233100 Email: rmidgley@control4.com

Wirepath Home Systems, LLC, DBA SnapAV 1800 Continental Blvd Suite 200, Charlotte, North Carolina 28273 USA DATE :2020/08/18 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AJACAN530APIAC Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

(List here the documents for which you are seeking confidentiality for example ) Schematics Block diagram Operation description Software Security Declaration These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Signature FCC grantee contact person information. Name/Title: Roger Midgley/ Principle Compliance Engineer Company Name: Wirepath Home Systems, LLC, DBA SnapAV Address: 1800 Continental Blvd Suite 200, Charlotte, North Carolina 28273 USA TEL: +18015233187 FAX: +18015233100 Email: rmidgley@control4.com

Wirepath Home Systems, LLC, DBA SnapAV 1800 Continental Blvd Suite 200, Charlotte, North Carolina 28273 USA DATE : 2020/08/18 FCC ID: 2AJACAN530APIAC Dear Sir, I hereby have entrusted the following person to be a proxy regarding application for Type Certification. Company name: Wirepath Home Systems, LLC, DBA SnapAV Address: 1800 Continental Blvd Suite 200, Charlotte, North Carolina 28273 USA Name: Roger Midgley Signature FCC grantee contact person information. Name/Title: Roger Midgley/ Principle Compliance Engineer Company Name: Wirepath Home Systems, LLC, DBA SnapAV Address: 1800 Continental Blvd Suite 200, Charlotte, North Carolina 28273 USA TEL: +18015233187 FAX: +18015233100 Email: rmidgley@control4.com

Wirepath Home Systems, LLC, DBA SnapAV 1800 Continental Blvd Suite 200, Charlotte, North Carolina 28273 USA Date: 2020/08/12 WIFI Channel 12 & 13 Declaration Letter To whom it may concern :

We have declared below featured for FCC equipment authorization in regard to 802.11b/g/n channel 12 & 13 operating capability for FCC ID : 2AJACAN530APIAC Please check Product hardware does not have the capability to operate on channel 12 & 13 Product hardware has the capability to operate on channel 12 & 13. However , these 2 channels will be disabled via software and user will not able to enable these 2 channels Product hardware has the capability to operate on channel 12 & 13. And meeting KDB 594280 D01 requirement. Pls explain detail here. _________________ Others Pls explain detail here. Name/Title: Roger Midgley/ Principle Compliance Engineer Company Name: Wirepath Home Systems, LLC, DBA SnapAV Address: 1800 Continental Blvd Suite 200, Charlotte, North Carolina 28273 USA TEL: +18015233187 FAX: +18015233100 Email: rmidgley@control4.com