D e v i c e I n s t a l l a t i o n G u i d e Option 1 : On wall directly Option 2 : The cassette 86x86 on wall Option 2 : The cassette 86x86 on wall
) Step 1 Step 2 Step 3 Step 1 Step 2 Step 3 Step 4
-Mini Gate User Manual Mini Gate User Manual
Address : 10/FTinwe Industrial Park Phase 2, Liufang Road No.6, Area No.67, Baoan District, ShenZhen Step 1: Screw stainless steel plate according to the 4 holes marked on the drawing,choose right size of screws by different walls. Step 2: Insert installing device aimed to stainless steel plate. Step 3: Fasten this screw on the bottom. Tel
86 755 86013579
Fax
86 755 86013575
Introduction for Function and Technical Data Step 1: Cassette 86*86 Step 2: Screw fixing board to cassette, choose the right size of screws by different cassettes. Step 3: Cover the fixing board. Step 4: Screw stainless steel plate to fixing board, then install device on the stainless steel plate. LCD LED Contactless Card Area
Keypad Part is for RF Card Key Pad USB Port Reset Botton Speaker List Quantity Mini-Gate biometric access control Fixing board A (plastic) Fixing board B (plastic) 1 1 1 Reading Area) Screw PM4X5 4+2 Screw PWM3X5 Power Adapter DC 12V/1.5A RJ45 Network Port Connector Fingerprint Sensor DC12V Power Connector L spanner Mini-Gate User Manual 1 1 1 1 1 1 l l l l l l l l l l l l l l l l l l l l 1 3 4 8 9 14 15 20 Type No Name Color Relay Wiegand RS485 Power Ethernet 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Relay 12V+
Relay-
GND(Relay GND) Wiegand_In_D1/LED_Input Wiegand_In_D0 GND(Wiegand GND) Wiegand_Out_D1 Wiegand_Out_D0 P_GND(Safety GND) GND(RS485 GND) RS485+
RS485-
GND(Power GND) Power_In(12V) POE-
POE+
RX-
RX+
TX-
TX+
Yellow&Green Black Black Black Yellow White Green Brown Purple Orange
D
T
T
Yellow Green Green White Black Yellow Gray Blue Blue Red Model ACD100P-CS Processor SAM9G45@400MHz, Processor Memory 128 MB DDR/ 128MB Flash Expansion Memory Micro SD(2GB for default configuration) LCD Display 1.8" TFT Color LCD LED Indicator Multi-color 3 K eypad 3 X 5 keypad Audio Beep PC Port High Speed USB2.0 Built-in Relay: 1 Power supply 12V DC/1.5A Current 450mA @ 12V Operating Temperature 0 ~ 50 C Storage Temperature 0 ~ 60 C Fingerprint Sensor Cogent CSD100, 500dpi Optical Sensor, (FBI Certified) Matching Speed 1:1 FRR 1%
FAR 0.001%
1.2s 1:N 2s (N 5000) Matching Security Grade Lower, Middle, High (Configurable) Acceptable Fingerprint Rotation +/-15 degree (Default) Module and Function Guide Advanced Mode Standard Mode Time Setting Lightness Setting Voice Setting Network Setting OK OK OK OK Administrator Setting Administrator Setting and and User User Setting Setting OK Note:
Factory Default: Administrator user ID:"1"; Pin #:"1". This will be invalid after new admin setup.
"User setting" should be changed to "admin setting"
Add Add Administrator Administrator Delete Delete Administrator Administrator Add User Delete User Fingerprint Mode OK OK OK OK OK Mode Setting
For fingerprint identify, select this mode. Fingerprint +
Fingerprint +
Card Mode Card Mode OK OK For For fingerprint + card fingerprint + card identify, select this mode. identify, select this mode. Card +
Card +
PIN Mode PIN Mode Fingerprint +
Fingerprint +
Card + PIN Mode Card + PIN Mode OK For For card + pin card + pin identify, select this mode. identify, select this mode. OK For For fingerprint + card + pin fingerprint + card + pin identify, select this mode. identify, select this mode. FCCStatements changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for Remark: USB port is used to firmware upgrade purpose, without loading.