| submitted | available | document details (if available) | source link |
|---|---|---|---|
| various | User Manual Revised | Users Manual | 1.27 MiB |
Quick Star t Guide MetroLinq 2.5G Outdoor 60 GHz PTP/PTMP + 5 GHz ML2.5-60-35 | ML2.5-60-19 | ML2.5-60-BF-18 Welcome to MetroLinq Interference-Free Gigabit Wireless Unboxing After opening the box, you will find MetroLinq (ML2.5-60-35, ML2.5-60-19, or ML2.5-60-BF-18) PoE Power Supply Power Cable Tools/Items Required 13 mm Socket Wrench Flat-Head Screwdriver Ethernet Cables Options Standard Bracket ICC-BRACKET-STD Long Range Precision Bracket ICC-BRACKET-LR Alignment Scope ICC-SCOPE-9x50 For helpful training and user-case information, please go to ignitenet.com/support Assembly The MetroLinq Standard Bracket and Long Range Precision Bracket
(both ordered separately) are designed for wall and pole mounting
(25 mm - 80 mm pole diameter). Choose what is best for your location and select hardware accordingly. 2 Install the Standard Bracket onto MetroLinq using four M8 bolts, lock washers, and flat washers. Grounding 1 2 Ensure the structure on which the unit is to be mounted is properly grounded and in compliance with ETSI ETS 300 253. Verify that there is a good electrical connection to a grounding point (no paint or isolating surface treatment). Use the included (M4) screw to attach a grounding wire (not included) to the grounding point on the unit, and then to ground. Caution: The earth connection must not be removed unless all supply connections have been disconnected. 1 Ensure all four position-locking bolts on the Standard Bracket are tight before installing. www.ignitenet.com 1 MetroLinq 2.5G E102017-CS 15020000xxxxA R01 Quick Start Guide 1 B 4 2 A 2 3 1 2 3 4 5 Note: Do not adjust bolts A and B without first loosening 1 and 4 respectively. Loosen coarse adjustment bolts 2 and 3 and set initial alignment. Dont worry, you dont have to be too accurate yet. After you have set the coarse alignment, tighten bolts 2 and 3. Loosen the horizontal fine-tune adjustment bolt 4. Use fine-
tune bolt "B" to optimize the horizontal position. Re-tighten bolt 4. Loosen the vertical fine-tune adjustment bolt 1. Use fine-
tune bolt "A" to optimize the vertical position. Re-tighten bolt 1. Initial alignment should be based on optical or visual alignment. After you achieve this, repeat steps 2 and 3 while watching the 60 GHz signal strength LED. Optimize position to the LED indicator. Ensure all bolts are fully tightened, remove the alignment scope (if installed), and enjoy Gigabit interference-free wireless. Power Up 1 Connect an Ethernet cable from the MetroLinq ETH PoE IN port to the PoE port on the power supply. 2 3 Connect Ethernet cable from the LAN port on the power supply to your LAN device. Connect the power cord to a nearby AC power source. Standard Bracket Alignment IgniteNet strongly recommends using the ICC-SCOPE-9x50 Alignment Scope for alignment. To install, place the scope on top of the MetroLinq housing and secure it with its thumb screw. 2 Software Safety and Regulatory Information Quick Start Guide 1 2 To configure your MetroLinq, connect your computer to the device through the LAN port of the power supply or directly to the ETH1 port on the device. The default IP mode is DHCP client, so if the device obtains an address from a DHCP server on the network, then use that IP (you can use the Discovery Tool from the IgniteNet support site to find the DHCP address). If the device does not obtain a DHCP address, it reverts to the fallback IP of 192.168.1.20 and you can access it on that IP. Direct your web browser to the correct IP and log in. username: root password: admin123 After you have logged in, follow the steps in the Setup Wizard to configure the device for your network. 2 After you have logged in, follow the steps in the Setup Wizard to configure the device for your network. For more configuration details and training, please go to ignitenet.com/support FCC Class B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The 5600-5650MHz band is disabled by software during manufacturing and cannot be changed by the end user. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. Professional installation is required. Note: The country code selection is for non-US models only and is not available on all US models. Per FCC regulation, all Wi-Fi products marketed in the US must be fixed to US operation channels only. Professional Installation Instructions 1. Installation personal This product is designed for specific applications and needs to be installed by a qualified person who has RF and related rules knowledge. The general user shall not attempt to install or change the settings. 2. Installation location The product shall be installed at a location where the radiating antenna can be kept 20 cm from nearby persons in normal operation conditions to meet regulatory RF exposure requirements. 3 3. External antenna Use only the antennas that have been approved by the applicant. Non-
approved antenna(s) may produce unwanted spurious or excessive RF transmitting power, which may lead to the violation of FCC/IC limits and is prohibited. 5G Antenna List:
Ant. Brand P/N Antenna Type Connector 1 Accton 120G00000176X Dish N/A Gain (dBi) Band 1 Band 4 12.1 10.1 Quick Start Guide 4. Installation procedure Please refer to user's manual for details. 5. Warning Please carefully select the installation position and make sure that the final output power does not exceed the limits set forcth in relevant rules. Violation of the rules could lead to serious federal penalties. Instructions d'installation professionnelle 1. Installation Ce produit est destin un usage spcifique et doit tre install par un personnel qualifi matrisant les radio-frquences et les rgles s'y rapportant. L'installation et les rglages ne doivent pas tre modifis par l'utilisateur final. 2. Emplacement d'installation En usage normal, afin de respecter les exigences rglementaires concernant l'exposition aux radio-frquences, ce produit doit tre install de faon respecter une distance de 20 cm entre l'antenne mettrice et les personnes. 3. Antenne externe Utiliser uniquement les antennes approuves par le fabricant. L'utilisation d'autres antennes peut conduire un niveau de rayonnement essentiel ou non essentiel dpassant les niveaux limites dfinis par FCC/IC, ce qui est interdit. 4. Procedure d'installation Consulter le manuel d'utilisation. 5. Avertissement Choisir avec soin la position d'installation et s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La violation de cette rgle peut conduire de srieuses pnalites fdrales. IC Statement This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This radio transmitter (IC: 3857A-ML2560) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le prsent metteur radio (IC: 3857A-ML2560) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. 60G Antenna List:
Ant. Brand P/N Antenna Type Connector Gain (dBi) 1 Accton 120300000225X Dish N/A 17.2 The maximum antenna gain permitted for devices in the band 5725-
5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate. Le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 23 cm between the radiator & your body. Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 23 cm de distance entre la source de rayonnement et votre corps. CE Mark CE Mark Declaration of Conformance for EMI and Safety (EEC) This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. National Restrictions This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country Bulgaria France Restriction None Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz italy None Luxembourg None Reason/Remark General authorization required for outdoor use and public service Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012 If used outside of own premises, general authorization is required General authorization required for network and service supply(not for spectrum) 4 Country Norway Restriction Implemented Russian Federation None Reason/Remark This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-lesund Only for indoor applications Note: Do not use the product outdoors in France. Europe - EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 Safety of Information Technology Equipment. EN 300 328 V1.8.1: 2012 Electromagnetic compatibility and Radio spectrum Matters (ERM);
Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive. EN 301 489-1 V1.9.2 (2011-09) EN 301 489-7 V1.3.1/ 2005 Electromagnetic compatibility and Radio spectrum Matters (ERM);
Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2.4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment. EN 55022 2010 + AC: 2011 Limits and methods of measurement of radio disturbance characteristics of information technology equipment. EN 55024: 2010 Information technology equipment immunity characteristics limits and methods of measurement. EN 62311: 2008 Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz - 300 GHz). This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 - 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Quick Start Guide The Declaration of Conformity (DoC) can be obtained from www.ignitenet.com -> support -> download -> declarations &
certifications. This equipment may be operated in:
Bulgarian Czech esky Danish Dansk Dutch Nederlands English Estonian Eesti Finnish Suomi French Franais German Deutsch Greek Hungarian Magyar Italian Italiano
, IgniteNet , 1999/5/EC. IgniteNet tmto prohlauje, e tento Radio LAN device je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Undertegnede IgniteNet erklrer herved, at flgende udstyr Radio LAN device overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF Hierbij verklaart IgniteNet dat het toestel Radio LAN device in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG Bij deze IgniteNet dat deze Radio LAN device voldoet aan de essentile eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC. Hereby, IgniteNet, declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Kesolevaga kinnitab IgniteNet seadme Radio LAN device vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. Valmistaja IgniteNet vakuuttaa tten ett Radio LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Par la prsente IgniteNet dclare que l'appareil Radio LAN device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Hiermit erklrt IgniteNet, dass sich dieser/diese/dieses Radio LAN device in bereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. (BMWi) Hiermit erklrt IgniteNet die bereinstimmung des Gertes Radio LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien) IgniteNet radio LAN device 1999/5/. Alulrott, IgniteNet nyilatkozom, hogy a Radio LAN device megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Con la presente IgniteNet dichiara che questo Radio LAN device conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. 5 Warnings and Cautionary Messages Quick Start Guide Warning: This product does not contain any serviceable user parts. Warning: Installation and removal of the unit must be carried out by qualified personnel only. Warning: When connecting this device to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards. Caution: Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment. Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards. Latvian Latviski Lithuanian Lietuvi Maltese Malti Polish Polski Portuguese Portugus Romanian Roman Slovak Slovensky Slovenian Slovensko Spanish Espaol Swedish Svenska Turkish Turk Ar o IgniteNet deklar, ka Radio LAN device atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. iuo IgniteNet deklaruoja, kad is Radio LAN device atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hawnhekk, IgniteNet, jiddikjara li dan Radio LAN device jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Niniejszym IgniteNet owiadcza, e Radio LAN device jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC. IgniteNet declara que este Radio LAN device est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE. IgniteNet declar c acest dispozitiv fr fir respect cerinele eseniale precum i alte dispoziii relevante ale Directivei 1999/5/EC. IgniteNet tmto vyhlasuje, e Radio LAN device spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES. IgniteNet izjavlja, da je ta radio LAN device v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES. Por medio de la presente IgniteNet declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE Hrmed intygar IgniteNet att denna Radio LAN device str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. IgniteNet bu kablosuz cihazn temel gereksinimleri ve 1999/
5/EC yonergesindeki ilgili koullar karladn beyan eder. NCC Statement (Taiwan) MPE 1mW/cm 58 cm TELEC Statement (Japan) 5.2/5.3GHzLAN All wireless LAN products in the 5.2/5.3GHz band cannot be used outdoors. Use the product only indoors. 6 Hardware Specifications Quick Start Guide Chassis Size (L x W x H:) Weight Temperature Humidity Network Interfaces Ports 60 GHz Radio 5 GHz Radio Radio Frequencies ML2.5-60-35:
350 x 350 x 200 mm (13.78 x 13.78 x 7.87 in.) ML2.5-60-19:
190 x 190 x 120 mm (7.48 x 7.48 x 4.72 in.) ML2.5-60-BF-18:
190 x 190 x 60 mm (7.48 x 7.48 x 2.36 in.) ML2.5-60-35: 3.5 kg (7.72 lb) ML2.5-60-19: 2 kg (4.41 lb) ML2.5-60-BF-18: 2 kg (4.41 lb) with mount Operating: -30 C to 55 C (-22 F to 131 F) / ML2.5-60-BF-18: -40 C to 70 C (-40 F to 158 F) Storage: -40 C to 70 C (-40 F to 158 F) Operating: 10% to 90% (non-condensing) ETH RJ-45 Port: 1000BASE-T, passive PoE SFP Port: 1000BASE-X IEEE 802.11ad IEEE 802.11ac 5150 ~ 5250 MHz (FCC) 5725 ~ 5850 MHz (FCC) 5745 ~ 5825 MHz (China) 5180 ~ 5320 MHz (ETSI) 5500 ~ 5700 MHz (ETSI) 58.32 ~ 64.80 GHz 48 VDC, maximum 0.5 A Power Supply Passive PoE Power Consumption 24 W maximum Regulatory Compliances Radio EN 300 328 V1.8.1:2012 EN 301 893 V1.7.1:2012 EN 301 489-1 V1.9.2 (2011-09) EN 301 489-17 V2.2.1:2012 FCC Part 15C 15.247/15.207 (2.4-2.4835GHz) FCC Part 15E 15.407 (5.150GHz-5.250GHz, 5.725-5.850GHz) EN 55022 2010+AC:2011 EN 61000-3-2 2006+A1:2009+A2:2009 FCC Class B Part 15 EN 55024 : 2010 EN 61000-4-2 : 2009 Emissions Immunity 7 IgniteNet Inc. 20 Mason, Irvine, CA, 92618 USA This antenna is normally mounted on a mast and is vertically polarized. Warning:
Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. The maximum e.i.r.p. at any elevation angle above 30 degrees as measured from the horizon must not exceed 125 mW (21 dBm). The antenna must be installed completely perpendicular to the horizon.
This product uses the FCC Data API but is not endorsed or certified by the FCC