FCC ID: CFS8DL-GRIPAIO7 7 inch All-In-One Wireless Control Panel

ADT7AIO/ADT5AIO Series Installation and Setup Guide STEP 1 - Installing the Rechargeable Backup Battery and STEP 2 - Setting up the Communication Links Power Connector The control is designed to be placed on a desk/table top with the stand attached or mounted to a wall using the back plate/cover. 1. Remove the Controls Case Back. 2. Install the ADTZWM (Wi-Fi and Z-Wave) and/or ADTLTE Communications modules (if used). Insert the Battery Pack into the case. 2. Connect the battery connector to the receptacle on the PC board. 3. 4. Secure the Battery Pack with the Battery Retainer using the Retaining Screw. 5a. Connect the power cable to the GND and +9V terminals on the AIO and to the +

and terminals on the Power Supply. Refer to Table 1 for wire gauge and length. Do not apply power at this time. OR 5b Connect the power supply connector to the receptacle on the AIO. Do not apply power at this time. NOTE: If using the optional wall mount configuration, skip to the wall mounting procedure. If not, complete step 7. 6. Install the Case Back onto the contorl and secure with the screw. Optional ADTZWM and ADTLTE Communications Module Note: Refer to the Specific Module Installation section in the online Installation & Reference Guide for instructions on mounting this module. SCREW Note: Do not connect to a receptacle controlled by a switch. 1. Plug the power supply into a 24-hour, 110VAC unswitched outlet. Upon power-

up, the Please Standby! will be displayed on the home screen. 2. Connect the Control to the local router. STEP 3 - Registration Programming and Testing On a laptop, PC or Smart Device, go to: https://alarmadmin.alarm.com. IMPORTANT: Once the programming procedure has started and the unit is powered up, do not remove power or disconnect the battery, nor open the case. Disconnecting power or activating the tamper switch can cause unpredictable programming results. Radio Activation Refer to the https://alarmadmin.alarm.com for radio activation. Testing the System The following test modes are available:

Walk Test Communication Diagnostics Enter Test mode (Walk Test) 1. After entering Installer Tools Menu Mode, select the Test button. 2. Select Walk Test. The system enters Walk Test Mode and Walk Test-Home To BATTERY Quit is displayed SCREW SCREW COVER ADTZWM MODULE EXT INT MACHINE SCREW ADTLTE MODULE POWER SUPPLY RECEPTACLE TERMINAL BLOCK V 9 D N G BATTERY CONNECTOR DETAIL A 0 V

-

9 0 0

-

p i r g Table 1 Wiring Guide Maximum distance between power supply and control Wire Gauge

(AWG) Note: Use UL-listed limited energy cable Up to 25 feet (7.62m) Up to 45 feet (13.72m) Up to 70 feet (21.34m) Up to 110 feet (33.53m)

# 22

# 20

# 18

# 16 Mounting the Base to a Wall (Optional) For wall mounting, perform to the following:

1. Secure the Mounting Plate to the wall with 4 screws. 2. Install the Tamper Screw as shown. 3. Secure the Control to the Mounting Plate by aligning the slots on the Base and sliding the unit down until locked in position. 4. Secure the Control with the screw. 3. Open each protected door and listen for three beeps from the keypad, followed by the zones Voice Descriptor. Identification of each faulted protection point should appear on the display, and clear when the door is closed. 4. Walk in front of the motion sensor and listen for three beeps and the zones voice descriptor. 5. When testing is complete, select the Home button and enter the Installer Code. 6. Press each key on the wireless key to confirm it performs its assigned function. Specifications Dimensions:

Voltage Input:

7.875 W x 5.75 H x 1.0 D P/N 300-10260: White 9VDC, 2.5A P/N 300-10260-BK (Black) 9VDC, 2.5A P/N 300-10260-CAN (Canada) 9VDC, 2.5A 24-Hour Backup Battery:

P/N 300-10186: Rechargeable Backup Battery:

Lithium-ion battery pack rated at 3.6/4.2V, 7500 mAH Communication Formats:

4-Digit Contact ID Home Health Care Applications IMPORTANT: In Home Health Care applications [UL1637] you must use pendant model SiXMEDICAL. The maximum range is 50 ft. Contacting Technical Support PLEASE, before you call Technical Support, be sure you:

READ THE INSTRUCTIONS!

Determine that the power supply and/or backup battery are supplying proper voltages. Verify your programming information where applicable. Note the proper model number of this product, and the version level (if known) along with any documentation that came with the product. Note your ADT customer number and/or company name. Having this information handy will make it easier for us to serve you quickly and effectively. For Documentation and Online Support See Installation and Setup Guide P/N 800-24121 or higher, which can be ordered by contacting Customer Service at 1-800-238-2727 (1-800-ADT-

ASAP). For technical support please call the ADT Product Support Group at 1-877-748-7628, option 3. This system must be checked by a qualified technician at least once every three (3) years 800----24121^

800 24121^

24121^

800800 24121^

800-24121 5/18 Rev. A Part 1 (BETA) The Limitations of this Alarm System While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:

Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second-floor detector, for example, may not sense a first-floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90 to 105F, the detection performance can decrease. Alarm warning devices such as sirens, bells, or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-

impaired people or waken deep sleepers. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners, and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments. RF Exposure Warning The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product procedures. Mise en Garde Exposition aux Frequences Radio: La/les antenne(s) utilise(s) pour cet metteur doit/doivent tre installe(s) une distance de sparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas tre situe(s) ni fonctionner paralllement tout autre transmetteur ou antenne, except en conformit avec les procdures de produit multi transmetteur FCC et ISEDs. This equipment should be installed in accordance with Chapter 2 of the National Fire Alarm Code, ANSI/NFPA 72, (National Fire Protection Association, Batterymarch Park, Quincy, MA 02269). Printed information describing proper installation, operation, testing, maintenance, evacuation planning, and repair service is to be provided with this equipment. Warning: Owners instruction notice: Not to be removed by anyone except occupant WARRANTY INFORMATION For the latest warranty information, please go to:

www.honeywell.com/security/hsc/resources/wa. For patent information, see www.honeywell.com/patents Warranty Patents Recommendations for Proper Protection The Following Recommendations for the Location of Fire and Burglary Detection Devices Help Provide Proper Coverage for the Protected Premises. Recommendations for Smoke and Heat Detectors With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #72 noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: For minimum protection a smoke detector should be installed outside of each separate sleeping area, and on each additional floor of a multi-floor family living unit, including basements. The installation of smoke detectors in kitchens, attics (finished or unfinished), or in garages is not normally recommended. For additional protection the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages. In addition, we recommend the following:

Install a smoke detector inside every bedroom where a smoker sleeps. Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the sleeper if the door is closed. Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air conditioners or humidifiers) are used. Install smoke detectors at both ends if the hallway is more than 40 feet (12 meters) long. Install smoke detectors in any room where an alarm control is located, or in any room where alarm control connections to an AC source or phone lines are made. If detectors are not so located, a fire within the room could prevent the control from reporting a fire or an intrusion. This Control Complies with NFPA Requirements for Temporal Pulse Sounding of Fire Notification Appliances Recommendations for Proper Intrusion Protection For proper intrusion coverage, sensors should be located at every possible point of entry to a home or premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system. This will ensure that alarm signals can be sent to the alarm monitoring station in the event that the communications are out of order (if connected to an alarm monitoring station). KITCHEN DINING BEDROOM BEDROOM TV ROOM KITCHEN DINING BDRM LIVING ROOM BDRM LIVING ROOM BEDROOM BEDROOM Smoke Detectors for Minimum Protection Smoke Detectors for Additional Protection BEDROOM Heat-Activated Detectors BEDROOM TO BR BEDROOM KTCHN

. CLOSED DOOR GARAGE LVNG RM BASEMENT floor_plan-001-V1 Federal Communications Commission & ISED Statements The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

If using an indoor antenna, have a quality outdoor antenna installed. Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. ISED CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC / ISED STATEMENT This device complies with Part 15 of the FCC Rules, and ISEDs license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS ISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. ADT Security Services, Inc. 1501 Yamato Road Boca Raton, FL 33431 Copyright 2018 ADT Security Services

ADT7AIO/ADT5AIO Series Security Systems Systmes de scurit Quick User Guide Guide d'utilisation rapide Guide d'utilisation rapide Guide d'utilisation rapide Guide d'utilisation rapide Ready To Arm Ready To Arm System Automation Arm Away Arm Stay Arm Custom Zones Scenes 9:11 AM Jauary 20, 2018 800-24123 5/18 Rev A Part 1 (BETA) Ref: ADT7AIO/ADT5AIO SYSTEM COMPATIBILITY NOTICE Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for use with your security system. Your Honeywell security system is not designed for use with any device that may be attached to your security system's keypad or other communicating bus if Honeywell has not approved such device for use with your security system. Use of any such unauthorized device may cause damage or compromise the performance of your security system and affect the validity of your Honeywell limited warranty. When you purchase devices that have been manufactured or approved by Honeywell, you acquire the assurance that these devices have been thoroughly tested to ensure optimum performance when used with your Honeywell security system. AVIS DE COMPATIBILIT DU SYSTME Votre systme de scurit Honeywell a t conu pour tre utilis avec des dispositifs fabriqus par Honeywell ou dont lusage avec votre systme de scurit a t approuv par Honeywell. Votre systme de scurit Honeywell nest pas conu pour tre utilis avec n'importe quel dispositif pouvant tre reli au clavier ou autre bus de communication de votre systme de scurit si Honeywell na pas approuv ledit dispositif pour utilisation avec votre systme de scurit. Lutilisation de dispositifs non autoriss peut entraner des dommages ou compromettre le fonctionnement de votre systme de scurit et invalider la garantie limite offerte par Honeywell. Lorsque vous achetez des dispositifs qui ont t fabriqus ou approuvs par Honeywell, vous avez la certitude que ces dispositifs ont t rigoureusement tests afin den optimiser le rendement lorsquils sont utiliss avec votre systme de scurit Honeywell. IMPORTANT!

If the panel is beeping rapidly when you enter the premises, an alarm has occurred during your absence and an intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location. IMPORTANT!

Si lors de votre entre sur les lieux le panneau met une tonalit rapide, cela indique quune alarme a t dclenche durant votre absence et quun intrus peut encore tre sur place. QUITTEZ IMMDIATEMENT et APPELEZ LA POLICE dun endroit sr proximit. FOR MORE DETAILED INFORMATION These instructions provide a brief overview of common system functions. For full details of all user functions, please see the systems User Guide located online at:

https://www.adt.com/help/faq/system-user-guides

(see ADT7AIO Security System User Guide P/N 800-24122 or higher) POUR DE L'INFORMATION PLUS DTAILL Ces instructions donnent un bref aperu des fonctions les plus courantes du systme. Pour de l'information plus dtaille, veuillez vous reporter au Guide de l'utilisateur complet qui se trouve en ligne au:

https://www.adt.com/help/faq/system-user-guides

(Consultez le guide de l'utilisateur pour systme de scurit ADT7AIO, n de pice 800-24122 ou guide ultrieur.)

- 2 -

IMPORTANT SECURITY NOTICE Your wireless key (key fob) is similar to your keys or access card. If lost or stolen, another person can compromise your security system. Immediately notify your Dealer/Installer of a lost or stolen key fob. The Dealer/Installer will then remove the wireless key programming from the security system. AVIS DE SCURIT IMPORTANT Votre tlcommande a la mme valeur que vos cls ou votre carte daccs. Si vous la perdez ou si elle est vole, une autre personne peut neutraliser le fonctionnement de votre systme de scurit. Si votre tlcommande est perdue ou vole, avertissez Le dtaillant/linstallateur pourra ensuite rendre inoprante la tlcommande dans votre systme de scurit. immdiatement installateur. dtaillant votre votre ou NOTES ON FIRE AND CO DETECTION Your fire alarm system (if installed) is on 24 hours a day, for continuous detection. In the event of an emergency, the smoke and heat detectors sound their alarms, triggering a loud, interrupted pulsed sound from the control and any external sounder(s) (if installed.) Carbon monoxide (CO) detectors, if installed, provide continuous detection. If a high level of carbon monoxide is detected, an interrupted pulsed alarm sound occurs at the control and the detector(s). Immediately move to a spot where fresh air is available, preferably outdoors. From a safe area, call your security service provider for further instructions. To silence the control sounding, enter 4 digit User Code followed the Off key. To silence the detector, see its instructions. REMARQUES RELATIVES LA DTECTION DINCENDIE ET DE MONOXYDE DE CARBONE Votre systme d'alarme incendie (si install) est actif 24 heures par jour afin doffrir une dtection continue. En cas d'urgence, les dtecteurs de fume et de chaleur font rsonner leurs alarmes, ce qui produit un son pulsations puissant et ininterrompu, mis depuis les contrles et tout avertisseur externe (si install). Les dtecteurs de monoxyde de carbone (CO), sils sont installs, offrent une dtection continue. Si un niveau lev de monoxyde de carbone est dtect, une alarme pulsation ininterrompue est mise par les contrles et le(s) dtecteur(s). Dplacez-vous immdiatement vers un endroit o de l'air frais est disponible, idalement l'extrieur. Une fois en lieu sr, contactez votre prestataire de services de scurit pour obtenir des directives additionnelles. Pour mettre le son des contrles en sourdine, saisissez le code utilisateur 4 chiffres, suivi de la touche Off (teindre). Consultez les instructions du dtecteur pour le mettre en sourdine.

- 3 -

Lyric Lock Your system supports advanced features designed to keep it functioning optimally. These capabilities include: the ability to interact with Honeywell and your dealers network for the setup and programming of its features, support for remote software updates and the ability (when enabled by your monitoring dealer) to enhance your security by preventing an unauthorized takeover of the system by another monitoring company. In the event that your dealer has enabled the feature to prevent an unauthorized takeover and you wish to authorize a new company to take over your system, you may request that Honeywell remotely disable this feature. Honeywell will require documentation that you have attempted to contact your existing security dealer and that they have failed to respond, or failed to agree to your request. Lyric Lock (Verrou Lyric) Votre systme supporte des fonctions de pointe conues pour le garder en fonction de manire optimale. Ces capacits comprennent : la capacit d'interagir avec le rseau de Honeywell et de votre dtaillant pour rgler et programmer ces fonctions, supporter les mises jour logicielles distance et la capacit (lorsque cela est activ par votre centre de tlsurveillance) de rehausser votre scurit en prvenant qu'une personne non autorise prenne en charge votre systme pour le transfrer un autre centre de tlsurveillance. Dans le cas o votre dtaillant aurait activ la fonction pour prvenir une prise en charge non autoris et que vous dsirez autoriser une autre entreprise prendre votre systme en charge, vous devez faire une demande afin que Honeywell dsactive cette fonction distance. Honeywell vous demandera de prouver que vous avez essay de communiquer avec votre dtaillant en scurit actuel et que vous n'avez pas reu de rponse ou que votre requte a t ignore.

- 4 -

Contents General Information ..................................................................................... 7 Information gnrale .................................................................................... 7 System Status LED Functions .................................................................. 7 Fonctions des DEL de l'tat du systme ........................................... 7 Navigating Menus ..................................................................................... 8 Navigation travers les menus ................................................................ 8 Function Icons .......................................................................................... 9 Icnes dfonction.................................................................................... 9 Panic Icons ............................................................................................. 10 Icnes durgence ................................................................................. 10 Master User Tools Icons ......................................................................... 11 Icnes doutils de lutilisateur matre...................................................... 11 Arm the System ......................................................................................... 13 Armement du systme ............................................................................... 13 Disarm the System ..................................................................................... 14 Dsarmement du systme ......................................................................... 14 Bypass Zones ............................................................................................ 15 Contournement de zones ........................................................................... 15 Panic Alarms .............................................................................................. 16 Alarmes de pnico ..................................................................................... 16 Assign User Codes .................................................................................... 17 Assignation de codes dutilisateur .............................................................. 17 Voice Command ........................................................................................ 18 Commande vocale ..................................................................................... 18 Settings ...................................................................................................... 19 Ajustes ....................................................................................................... 19 Advanced Features .................................................................................... 20 Fonctions avances ................................................................................... 20 Bluetooth Feature ...................................................................................... 21 Fonctions Bluetooth ................................................................................... 21 Voice Command ........................................................................................ 22 Commande vocale ..................................................................................... 22 Events Feature ........................................................................................... 23 Fonctions Activits ..................................................................................... 23 Configure Wi-Fi ........................................................................................ 24 Configuration Wi-Fi .................................................................................. 24 Help Videos ................................................................................................ 26

- 5 -

Contents Help Videos ................................................................................................ 26 Vidos d'aide ............................................................................................. 26 Amazon Alexa ............................................................................................ 27 Amazon Alexa ............................................................................................ 27 Test the System ......................................................................................... 28 Tester le systme ....................................................................................... 28 Wireless Keys (Key Fobs) .......................................................................... 29 Fonction de la tlcommande .................................................................... 29

- 6 -

General Information / Information gnrale The ADT7AIO/ADT5AIO are wireless Control Units that allow you to perform system arming and disarming functions, as well as to monitor the status of your security system. Les ADT7AIO/ADT5AIO sont des units de commande sans fil qui vous permettent d'armer et de dsarmer un systme, ainsi que de surveiller l'tat de votre systme de scurit. Wi-Fi STATUS /

TAT DU Wi-Fi BUILT-IN CAMERA /

CAMRA INTGRE STATUS LEDs (2) /

DEL D'TAT (2) SYSTEM STATUS /

TAT DU SYSTME Ready To Arm Ready To Arm System Automation Arm Away Arm Stay Arm Custom Zones Scenes 9:11 AM Jauary 20, 2018

(ADT7AIO Shown/ADT7AIO prsent) PANIC /

PANIQUE TOUCH SCREEN /

CRAN TACTILE HOME /

ACCUEIL grip-043FC-V0 System Status LED Functions/Fonctions des DEL de l'tat du systme LED/DEL Meaning/Signification Status/Statut Power

(Left) Alimentation

(gauche) Status

(Right) Statut

(Droite) Green Steady Vert Continueous Red Blinking Rouge Clignote Off teint Green Steady Vert Continueous Red Steady Rouge Continueous Red Flashing Rouge Clignotant Off teint Amber Steady Amber Continueous Green Flashing Vert Clignotant Amber Flashing Ambre Clignotant AC Connected/Battery Charged CA branch/batterie charge Low Battery Batterie faible No AC Power Pas dalimentation CA System Ready to Arm Systme prt larmement System Armed Systme arm Alarm or Alarm Memory or in Programming mode Alarme ou Mmoire dalarme ou Mode programmation Not ready to arm Pas prt tre arm System trouble Dfectuosit du systme Device trouble System can be armed Anomalie de priphrique le systme peut tre arm Device trouble System cannot be armed Anomalie de priphrique le systme ne peut pas tre arm

- 7 -

General Information / Information gnrale

(Continued) Navigating Menus / Navigation travers les menus System Status is displayed at the top of each screen and the time and date are displayed at the bottom. The Security Screen displays the system status and selection icons. The displayed pages and options may vary slightly depending upon the devices and services that are installed in or connected to the system. Ltat du systme saffiche en haut de lcran, et lheure et la date saffichent en bas. Lcran de scurit affiche ltat du systme et les icnes de slection. Les options qui saffichent peuvent lgrement varier selon les dispositifs et services qui sont installs dans le systme ou connects ce dernier. Ready To Arm Ready To Arm System Automation Arm Away Arm Stay Arm Custom Zones Scenes 9:11 AM Jauary 20, 2018 Home Screen/cran daccueil

(ADT7AIO Shown/ADT7AIO prsent) grip-001-V0

- 8 -

General Information / Information gnrale

(Continued) Function Icons / Icnes dfonction Selection Arm Away

(Arm Total) Arm Stay

(Arm. Partiel) Arm Custom

(ArmerPerso) System

(Systme) Automation

(Automati) Zones Scenes Tools

(Outils) Function Used to Arm the system in Away mode. Utilise pour armer le systme en mode Total. Used to Arm the system in Stay mode. Utilise pour armer le systme en mode Partiel. Used to Arm the system in Custom mode. Utilis pour armer le systme en mode Custom (Personnalis) afin dactiver les zones slectionnes. Provides information about system status. Fournit linformation propos de ltat du systme. Provides access to Home Automation options (Master User Code required for access). Permet daccder aux options de domotique (le code matre est requis pour laccs). Provides access to Zone information and options. Fournit laccs linformation et aux options des zones. Provides access to Home automation features. Permet daccder aux fonctions de domotique. Provides access to Installer and User Programming options

(Master User Code required for access). Fournit laccs aux menus de programmation de linstallateur et de lutilisateur (le code matre est requis pour laccs).

- 9 -

General Information / Information gnrale

(Continued) Function Icons / Icnes dfonction (Continued) Selection

. Function Provides access to Wi-Fi information. Permet d'accder aux renseignements sur le Wi-Fi Enables or disables voice operation mode. Active ou dsactive les commandes vocales. View messages from ADT. Affichage des messages ADT. Provides access to Panic icons. Donne accs aux icnes de panique. Provides access to Keypad. Donne accs au clavier. Panic Icons / Icnes durgence Selection Function Alerts the monitoring company that a fire condition exists.

(Displays zone 995) Lorsque active, avertit le centre de tlsurveillance quune condition de feu existe. (Affiche zone 995) Alerts the monitoring company that a police emergency exists.

(Displays zone 999, default is silent) Lorsque active, avertit le centre de tlsurveillance quune urgence ncessitant l'intervention de la police existe. (Affiche zone 999 et par dfaut aucune tonalit n'est mise) If programmed, alerts the monitoring company to other types of emergency.

(Displays zone 996) Si cette option est programme, une alerte est transmise au centre de tlsurveillance ou d'autres types d'intervenants.

(Affiche zone 996)

- 10 -

Fire

(Feu) Police

(Police) Personal

(Personnel) General Information / Information gnrale

(Continued) Master User Tools Icons / Icnes doutils de lutilisateur matre Selection Function Provides Master User access to manage (add/remove) Users. Refer to the Assign User Codes section. Offre un accs dutilisateur matre pour grer

(ajouter/supprimer) des utilisateurs. Consultez la section Assigner des codes utilisateur. Provides Master User access to Settings features. Refer to the Settings section. Offre un accs dutilisateur matre aux paramtres. Consultez la section Rglages. Provides Master User access to Advanced features. Refer to the Advanced Features section. Offre un accs dutilisateur matre aux fonctions avances. Consultez la section Fonctions volu. Provides Master User access to Bluetooth feature. Refer to the Bluetooth section. Offre un accs dutilisateur matre la fonction Bluetooth. Consultez la section Bluetooth. Provides Master User access to Voice Command feature. Refer to the Voice Command section. Offre un accs dutilisateur matre aux commandes vocales. Consultez la section Commandes vocales. Provides Master User access to Events feature. Refer to the Events section. Offre un accs dutilisateur matre la fonction Activits. Consultez la section Activits. Provides access to Wi-Fi Configuration feature. Refer to the Configure WiFi section. Permet d'accder la configuration du Wi-Fi. Consultez la section Configuration du Wi-Fi.

- 11 -

Users

(Utilsateurs) Settings

(Rglages) Advanced

(volu) Bluetooth Voice Command

(Command Vocale) Events

(Activits) WiFi Config

(Config WiFi) General Information / Information gnrale

(Continued) Master User Tools Icons / Icnes doutils de lutilisateur matre Provides access to Alexa feature. Refer to the Alexa section Permet d'accder la fonction Alexa. Consultez la section Alexa. Provides access to Help Videos feature. Refer to the Help Videos section. Permet daccder la fonction Vidos d'aide. Consultez la section Vidos d'aide. Alexa Help Videos

(Vidos d'aide)

- 12 -

Arm the System / Armement du systme 1 Select arming mode. Arm Away (when youre out) OR Arm Stay (when youll be home) OR Arm INSTANT entry delay on/off Arm Custom (bypass selected zones) Slectionnez le mode d'armement. Arm. Total (lorsque vous tes absent) OU Arm. Partiel (lorsque vous demeurez sur les lieux) OU Armement INSTANT de dlai dentre activ/dsactiv ArmerPerso (Armement Personnalis) (les zones slectionnes sont contournes) Enter user code. Entrez un code dutilisateur. System arms in selected mode Exit Delay countdown begins Keypad beeps begin, if enabled

(Silent Exit mutes countdown beeps) Le systme s'arme dans le mode slectionn Le compte rebours du dlai de sortie commence Le clavier commence mettre des bips, si cette option est active

(L'option SORTIE SILEN. [Sortie silencieuse] met en sourdine le compte rebours)

- 13 -

2 1 4 7 Clear 2 5 8 0 3 6 9 3 What Happens Ce qui se produit Disarm the System / Dsarmement du systme 1 Select Disarm icon. Slectionnez sur l'icne Dsarmer. Enter user code. Entrez un code dutilisateur. Disarm

(Desarmer) 2 1 4 7 Clear 2 5 8 0 3 6 9 3 What Happens System disarms Entry Delay beeps stop (if beeps enabled) Ce qui se produit Memory of Alarm Mmoire dalarmes Le systme se dsarme Les bips du dlai d'entre s'arrtent (si les bips sont activs) If an alarm has occurred, zones with alarms remain displayed. Repeat Disarm sequence to clear display. Si une alarme s'est produite, les zones qui ont dclench l'alarme demeurent affiches. Rptez la squence de dsarmement pour effacer l'afficheur.

- 14 -

4 Bypass Zones / Contournement de zones NOTE: Bypassed zones are unprotected. NOTE : Les zones contournes ne sont pas protges. Zones BYPASS 1 4 7 Clear 2 5 8 0 3 6 9

-

1 2 3 4 5 6 Select Zones icon. Slectionnez sur l'icne Zones. Select zones to bypass from list. Slectionner parmi la liste les zones contourner. Select BYPASS. Appuyez sur BYPASS (Contourner). Enter user code. Entrez un code dutilisateur. icon. Bypassed zones appear in list with Les zones contournes apparaissent dans la liste avec l'icne Arm the system as usual. Armez le systme comme d'habitude.

- 15 -

Panic Alarms / Alarmes de pnico See your installer for types of Panic alarms programmed for your system. Consulte seu instalador sobre os tipos de alarme de pnico programados em seu sistema. 1 2 Select the Panic Icon. Slectionnez sur l'icne Urgence Select the desired panic icon. Alarm message is sent to ADT. Appuyez sur l'icne d'urgence applicable. Un message dalarme est transmis au ADT. Fire

(Feu) Police Personal

- 16 -

Assign User Codes / Assignation de codes dutilisateur 1 Select the Tools Icon. Slectionnez sur l'icne Tools (Outils). Enter Master User code. Entrez un code dutilisateur. Select Users icon. Slectionnez sur l'icne Users (Utilsateurs). Tools

(Outils) 3 6 9 1 4 7 Clear 2 5 8 0 Users

(Utilsateurs) 1. Master 2. New - Standard User 3. New - Standard User Name

*

User Code

****

1 4 7 Clear 2 5 8 0 3 6 9 Partitions 1 2 3 To assign a Master, or New User code, select the desired option then select Edit or Add new Pour assigner un code matre, un code d'invit ou de contrainte, slectionnez sur l'option dsire et ensuite sur Edit (Modifier) ou Add new (Ajouter). Select Name and assign a personal name to this user. Select Save.

* The default User description is displayed. Slectionnez Name (Nom) et assignez un nom personnel cet utilisateur. Slectionnez Save (Garder).

* La description par dfaut de lutilisateur s'affiche. Select User Code to assign a 4-digit code to this user. Slectionnez User Code (Code utilisateur) pour assigner un code 4 chiffres cet utilisateur. Assign 4-digit code to this User and select Save. Assignez un code 4 chiffres et appuyez sur Save

(Garder). Select the applicable Partitions for this User (if applicable). Slectionnez les partitions applicables pour cet utilisateur (sil y a lieu).

- 17 -

2 3 4 5 6 7 8 Assign User Codes / Assignation de codes dutilisateur 9 Authority Level Select Authority Level (if applicable). Slectionnez le niveau d'autorit (sil y a lieu). Select Authority Level for this User (if applicable). Select Save. Slectionnez le niveau d'autorit pour cet utilisateur (sil y a lieu). Slectionnez Save (Enregistrer). Standard User 10 Standard User Arm Only Guest Duress Partition Master

- 18 -

Settings / Ajustes 1 Tools

(Outils) 3 6 9 1 4 7 Clear 2 5 8 0 Settings

(Reglages) Brightness Brightness Volume Brightness /

Volume

(Brillance /

Volume) Brightness Volume VOICE CHIMES Clean Voice / Chime

(Voix / Carillon) Clean

(Nettoyer) Select the Tools Icon. Slectionnez sur l'icne Tools (Outils). Enter Master User code. Entrez un code dutilisateur. Select the Settings icon. Slectionnez sur l'icne Settings (Rglages).

+

+

+

+

Adjust screen brightness and Voice/Chime volume. Rgler la brillance de l'cran et le volume vocal/du carillon. Select Voice or Chime to mute voice announcements and/or chime sounds if desired (highlighted [blue] button indicates mutedactive). Slectionnez sur Voice (Voix) ou Chime (Carillon) pour mettre en sourdine les annonces vocales et/ou les sons de carillon (un bouton surlign en [bleu] indique une fonction mise en sourdine). Select Clean icon before cleaning the screen; use a damp, soft cloth while screen is disabled for 15 seconds. Slectionnez sur l'icne Clean (Nettoyer) avant d'effacer l'cran; utilisez uniquement un linge doux et humide alors que l'cran est dsactiv pour 15 secondes.

- 19 -

2 3 4 5 6 Advanced Features / Fonctions avances Several advanced User features are available. Refer to the full User Guide for additional information regarding these features. Plusieurs fonctions Utilisateur avances sont disponibles. Consultez le guide de l'utilisateur complet pour obtenir des informations supplmentaires au sujet de cette fonction. 1 Select the Tools Icon. Slectionnez sur l'icne Tools (Outils). Enter Master User code. Entrez un code dutilisateur. Select Advanced icon. Slectionnez sur l'icne Advanced (volu). Select the desired feature. Slectionnez la fonction voulue. 2 3 4 Tools

(Outils) 3 6 9 1 4 7 Clear 2 5 8 0 Advanced

(volu) System Reboot System Halt Connect Home Walk Test Comm. Test Takeover 5800 Module

- 20 -

Bluetooth Feature / Fonctions Bluetooth 1 2a 2b Bluetooth ADD NEW EDIT DELETE Select the Bluetooth Icon. Slectionnez sur l'icne Bluetooth. Select ADD NEW. Follow the prompts to connect a Bluetooth device. Slectionnez ADD NEW (Ajouter nouveau). Suivez les directives pour connecter un appareil Bluetooth. Select EDIT or DELETE. Follow the prompts. Slectionnez EDIT (Modifier) ou DELETE

(Supprimer). Suivez les directives.

- 21 -

Voice Command / Commande vocale Voice Command offers control of Security Functions, Z-Wave devices and Video functions by speaking in plain language. User-selected trigger phrases spoken near the Controller alert the system to listen for further instructions. Refer to the full User Guide for additional information regarding this feature. 1 Tools

(Outils) 3 6 9 1 4 7 Clear 2 5 8 0 Select the Tools Icon. Slectionnez sur l'icne Tools (Outils). Enter Master User code. Entrez un code dutilisateur. Select Voice Command icon. Voice Command Slectionnez sur l'icne Voice Command (Commande vocale). Select Voice Training and follow the directions displayed on the touchscreen. Voice Training Slectionnez Voice Training (Formation Vocales) et suivez les directives affiches sur l'cran tactile. Command Sensitivity Trigger Sensitivity

-

- Volume

-

+

+

+

ENABLE TRIGGER FEEDBACK Adjust Voice functions using the sliding bars as applicable. Rglez les fonctions vocales laide des barres de dfilement, sil y a lieu. Enable/Disable Trigger Feedback by toggling the Enable Trigger Feedback selection. Activer/dsactiver la rtroaction par dclencheur en slectionnant Enable Trigger Feeback selection

(Activer la rtroaction par dclencheur).

- 22 -

2 3 4 5 6 Events Feature / Fonctions Activits Select the Events Icon. 1 Slectionnez sur l'icne Activits. Events

(Activits) ALL Select ALL to scroll through the viewable Event options (All, Trouble, Bypass, Open, Close or Non-

Security). The system displays the selected Events. Slectionnez ALL (Tous) pour faire dfiler les options dactivits que vous pouvez visionner (Tous, Anomalie, Contourner, Fermer ou Non scuris). Le systme affiche les activits slectionnes.

- 23 -

2 Configure Wi-Fi / Configuration Wi-Fi Connect the control to the your local network router. Branchez le contrleur votre routeur de rseau local. 1 2 3 4 Tools

(Outils) 3 6 9 1 4 7 Clear 2 5 8 0 WiFi Config

(Config WiFi) 5a Scan for Network Select the Tools Icon. Slectionnez sur l'icne Tools (Outils). Enter Master User code. Entrez un code dutilisateur. Select the WiFi Config Icon. Slectionnez sur l'icne WiFi Config (Config WiFi). Select from the following options:

Scan for Network (to automatically display aviailable networks) Manually Connect to the Network (Manually connect to a WiFi network) WPS (connect to a network via Wi-Fi Protected Setup) Note :This option requires a WPS capable router. Slectionnez parmi les options suivantes :

Scan for Network (pour afficher automatiquement les rseaux disponibles) Manually Connect to the Network (connexion manuelle un rseau Wi-Fi) WPS (connexion un rseau par protocole Wi-Fi Protected Setup) Note : cette option ncessite un routeur capacit WPS. a. Select the desired network. b. Enter the required information. c. Select OK. a. Slectionnez le rseau auquel vous voulez vous connecter. b. Saisissez les renseignements requis. c. Slectionnez OK.

- 24 -

Configure Wi-Fi / Configuration Wi-Fi 5b Manually Connect to the Network a. Enter the required information. b. Select OK. a. Saisissez les renseignements requis. b. Slectionnez OK. Follow the prompts. Suivez les messages-guides. WPS 5c

- 25 -

Help Videos / Vidos d'aide 1 Help Videos

(Vidos d'aide) 2 Select the Help Videos Icon. Slectionnez sur l'icne Vidos d'aide. Select from the displyaed options to play Help Videos associated with the Security System. Parmi les options affiches, faites une slection pour lancer des vidos d'aide associes au systme de scurit.

- 26 -

Amazon Alexa / Amazon Alexa 1 Select the Tools Icon. Slectionnez sur l'icne Tools (Outils). Tools

(Outils) 3 6 9 1 4 7 Clear 2 5 8 0 Alexa 2 3 Enter Master User code. Entrez un code dutilisateur. Select the Alexa Icon. Refer to the full User Guide for additional information about this feature. Slectionnez sur l'icne Alexa (Alexa). Consultez le guide de l'utilisateur complet pour obtenir des informations supplmentaires au sujet de cette fonction.

- 27 -

Test the System (to be conducted weekly) Tester le systme ( effectuer chaque semaine) Disarm the system and close all protected windows and doors. The status LED should be lit Green. NOTE: Alarm messages are NOT sent to your alarm monitoring company during these tests. Dsarmez le systme et fermez toutes les fentres et portes protges. La DEL d'tat devrait s'allumer en vert. NOTE: Durant ces tests, les messages dalarme ne sont PAS achemins vers lentreprise de surveillance. 1 2 3 Tools

(Outils) 1 4 7 Clear 2 5 8 0 3 6 9 Advanced

(volu) Trigger Zones Dclenchement de zones 4 5 Exit Test mode Quitter le Mode de test Select the Tools Icon. Slectionnez sur l'icne Tools (Outils). Enter Master User code. Entrez un code dutilisateur. Select Advanced icon, then select Walk Test Slectionnez sur l'icne Advanced (volu), puis slectionnez Walk Test (Test par dplacement. Trigger (open and close) all zones. Listen for three beeps from the controller when each zone is triggered. Dclenchez toutes les zones (ouvertes et fermes). Soyez attentif et attendez d'entendre 3 bips provenant du panneau de commande chaque fois qu'une zone est dclenche. When testing is completed, press the Home button on the controller and enter the Master User Code if prompted. Une fois le test complt, appuyez sur le bouton Accueil sur le panneau de commande et entrez le code d'utilisateur matre si cela vous est demand.

- 28 -

Wireless Key (Key Fob) Functions Each wireless key button has a preprogrammed function. Ask your installer to identify the functions assigned for each button. NOTES:

One or more buttons may have been programmed as a panic function. To activate a button function, press and hold the button for 1-2 seconds. Une fonction a t programme l'usine pour chaque bouton de la tlcommande. Demandez votre installateur de vous indiquer quelles sont les fonctions qui ont t assignes chaque bouton. NOTES:

Un ou plusieurs boutons peuvent avoir t programms pour des fonctions d'urgence. Pour activer la fonction d'un bouton, maintenez enfonc le bouton durant une deux secondes. 1: ____________________________ 2: _____________________________ 3: _____________________________ 4: _____________________________ 8*: ____________________________

(*press and hold BOTH buttons to activate)

(*maintenez les deux boutons enfoncs pour activer la fonction) 1 KEY 3 KEY LEDs 2 KEY 4 KEY lyric-058-V0 8*

- 29 -

- 30 -

- 31 -

ADT Security Services 1501 Y amato Road Boca Raton, FL 33431 2018 ADT Security Serv ices 800-24123p 800-24123 5/18 Rev A Part 1

CFS8DL-GRIPAIO7 / 573F-GRIPAIO7 EXHIBIT 8 Label Information LABEL INFORMATION EXACT LOCATION OF THE LABEL:

Label is located on the rear of the wall-mounting plate in the location shown:

FCC/IC IDs Location Honeywell Internal Page 1 of 2 EXHIBIT 8 Label Information LABEL CFS8DL-GRIPAIO7 / 573F-GRIPAIO7 Honeywell Internal Page 2 of 2

2 Corporate Center Drive Melville, NY 11747 516-577-2000 CFS8DL-GRIPAIO7 FCC COVER LETTER Date: 06/18/2018 To Whom It May Concern:

This letter is to inform you of our request for a new certification for our transceiver known as CFS8DL-GRIPAIO7. The transceiver will operate under Part 15.247. Regards, X Michael Antola Honeywell Internal

2 Corporate Center Drive Melville, NY 11747 516-577-2000 Request for Confidentiality Date: 06/18/18 Subject: Confidentiality Request for: CFS8DL-GRIPAIO7 Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 9.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent*1 Permanent Permanent Permanent Permanent Permanent Permanent*3 Exhibit Functional Description External Photos Internal Photos Circuit Description & Block Diagram Message Timing & Duty Cycle Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual Honeywell has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify UL Verification Services in the event information regarding the product or the product is made available to the public. UL Verification Services will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By:

(Signature/Title2) _/ Hardware Engineer__ __Michael Antola___________

(Print name) 1 - The asterisked items (*) require further information to be provided to UL Verification Services before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.