FCC ID: CFS8DL6C2W Convert to Wireless Module

SiXC2W Convert to Wireless / Convert to Wireless Quick Installation Guide The Honeywell SiXC2W is an eight zone hardwire to wireless converter used with controllers that support Honeywells SiX series devices. It is useful in retrofit 12-

volt security system applications where existing contact wiring was used. It uses those existing wired contacts and converts them to wireless. FEATURES Provides 12-volts for devices such as motion detectors, glass breaks, etc. NOTE: Only two devices may be powered using the auxiliary output on the SiXC2W. Provides 24-hour battery backup (4-hour if external devices are connected). NOTE: It immediately sends a power loss signal to the controller in the event the power is lost. When no battery is connected, low battery message will send to control panel. When battery is connected, and if battery voltage drops below 3.6VDC, a low battery message sends to the control panel. When only the battery is connected, and if the battery voltage 3.4 V, system will shut down. Support one button calibration Automatic zone configuration Easy setup in three steps Cover tamper protection IMPORTANT!

Not to be used for fire, heat, or carbon monoxide detectors. CALIBRATING The calibration process enables the SiXC2W to learn what zones are to be active and what value EOL resistors are used. IMPORTANT!

Unused zones that are open ARE NOT recognized and reported. 1. Ensure all zones are connected and not faulted. 2. On the SiXC2W, press and release the top middle 3. button. Indicator LED #2 will flash Red for 1/2 second; then LED #3 turns steady Green. 4. Calibration is in process 5. DONE. The SiXC2W is calibrated and ready to enroll in the control panel. NOTES:

If the SiXC2W loses both AC and battery backup power, the zone calibration data is retained. If there is an existing resistor, it MUST have a value between 1K and 10K.The unit comes with eight (8) 2.2K resistors for zones that dont have one. IMPORTANT!

Once the SiXC2W is calibrate, any change in the zone resistance the module must be re-calibrated. Guide d'installation rapide The Honeywell SiXC2W is an eight zone hardwire to wireless converter used with controllers that support Honeywells SiX series devices. It is useful in retrofit 12-volt security system applications where existing contact wiring was used. It uses those existing wired contacts and converts them to wireless CARACTRISTIQUES Provides 12-volts for devices such as motion detectors, glass breaks, etc. NOTE: Only two devices may be powered using the auxiliary output on the SiXC2W. Provides 24-hour battery backup. (4-hour if external devices are connected). NOTE:

It immediately sends a power loss signal to the controller in the event the power is lost. When no battery is connected, low battery message will send to control panel. When battery is connected, and if battery voltage drops below 3.6VDC, a low battery message sends to the control panel. When only the battery is connected, and if the battery voltage 3.4 V, system will shut down. Support one button calibration Automatic zone configuration Easy setup in three steps Cover tamper protection IMPORTANT!

Not to be used for fire, heat, or carbon monoxide detectors. CALIBRATING The calibration process enables the SiXC2W to learn what zones are to be active and what value EOL resistors are used. IMPORTANT!

Unused zones that are open ARE NOT recognized and reported 1. Ensure all zones are connected and not faulted. 2. On the SiXC2W, press and release the top middle 3. button. Indicator LED #2 will flash Red for 1/2 second;

then LED #3 turns steady Green. 4. Calibration is in process 5. DONE. The SiXC2W is calibrated and ready to enroll in the control panel. NOTES:

If the SiXC2W loses both AC and battery backup power, the zone calibration data is retained. If there is an existing resistor, it MUST have a value between 1K and 10K.The unit comes with eight (8) 2.2K resistors for zones that dont have one. IMPORTANT!

Once the SiXC2W is calibrate, any change in the zone resistance the module must be re-calibrated. ENROLLING / ENROLLING Lyric Control Lyric Controller Enrollment Process, See Controllers installation instructions for its proper programming process. For Lyric Gateway Use AlarmNet 360 to enroll and program this sensor. Lyric Control Lyric Controller Enrollment Process, See Controllers installation instructions for its proper programming process. For Lyric Gateway Use AlarmNet 360 to enroll and program this sensor. For Other Controls For other controls that support SiX series devices, see the controllers installation app for details NOTE: Once enrolled in a system, the SiXC2W cannot be used with another controller until it is removed from the current controller. See the Controllers instructions for details. For Other Controls For other controls that support SiX series devices, see the controllers installation app for details NOTE: Once enrolled in a system, the SiXC2W cannot be used with another controller until it is removed from the current controller. See the Controllers instructions for details. MOUNTING / MONTAGE Signal strength:

Rang of 1-4 bars (green), should be a minimum 1 green bar for the zone being programmed. Four Red Bards indicate poor signal strength; the device should be relocated. See the controllers instruction for bar indication signal strength values. Icon Description 4 Green Bars Signal Strength 3 Green Bars 2 Green Bars 1 Green Bar Good 4 Red Bars Relocate TAMPER/LOW BATTERY REPORTING The SiXC2W reports this condition to the control. If a low battery or tamper condition exists all zones used on the module shows a trouble on the control. TAMPER/LOW BATTERY REPORTING The SiXC2W reports this condition to the control. If a low battery or tamper condition exists all zones used on the module shows a trouble on the control. IMPORTANT:

The first battery test occurs 1 hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within 1 minute. IMPORTANT:

The first battery test occurs 1 hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within 1 minute. LED INDICATIONS LED # / LED #

1 (Green / Green) 2 (Red / Red) 3 (Green / Green) 4 (Green and Red /

Green and Red) Functions / Functions Blinks once upon RF signal transmission (HW zone trigger/tamper and/or a fault message), slow blink for a cover tamper, quick blinks for enrollment or deletion / Blinks once upon RF signal transmission (HW zone trigger/tamper and/or a fault message), slow blink for a cover tamper, quick blinks for enrollment or deletion Blinks 1s / 1s off when module needs calibrating / Blinks 1s /

1s off when module needs calibrating Steady on when the module has been calibrated. / Steady on when the module has been calibrated. Green: 5VDC Power from the plug-in transformer is present Red (blinking 1sec on / 1 sec off): Running on battery, DC power not present. / Green: 5VDC Power from the plug-in transformer is present Red (blinking 1sec on / 1 sec off):

Running on battery, DC power not present. Approval Listings / Approbations Homologations:

FCC / IC - ETL Listed to UL268 & 521 cETL Listed to ULC S530 & S531 Other Standards / Autres normes: RoHS FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS dIndustrie Canada. Son fonctionnement est soumis aux conditions suivantes:

(1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. SPECIFICATIONS / SPCIFICATIONS:

Voltage Transformer Part # ................................... 300-10259 Input Voltage ............................................... 100 ~ 240VAC, 50 ~60 Hz Operating Voltage ..................................... 5VDC Maximum Transformer Distance ...... 9.8ft. (3m) Voltage Output ........................................... 12VDC @ 100mA (Up to three sets of 2024 Battery/ Pile ................................................. P/N 300-10342 Environmental Operating Temp ......................................... 14 F (-10C) to 140F (60C) Relative Humidity ...................................... 95%, Non-condensing / 95% max. sans NOTE: Charging the lithium battery stops when temperature is below 32F

(0C) gauge wiring) condensation Physical Dimensions .................................................. Length 7.0 in (178 mm) x Mounting Hardware ................................. Double stick tape and screws Zone Resistance ......................................... 1K to 10K Ohm EOL Resistors Zone Wiring .................................................. 1,000ft (Each Zone) Width 4.5 in (114 mm) x Depth 1.5 in (38mm) Radio Frequency Transmission Range ................................ 300ft (91.5m) BATTERY REMOVAL AND INSTALLATION Caution: The batteries used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 212F

(100C) or dispose of in fire. Use Panasonic CR123A or DURACELL DL123, DL 123A Lithium batteries. Use of other batteries may present a risk of fire or explosion. Keep used batteries away from children. Dispose of used batteries properly. Remove old batteries. Wait 10 seconds and then replace with four new batteries. To avoid a low battery indication when installing new batteries, both batteries must be installed within 15 seconds of installing the first one. Any low battery condition that may have occurred should clear when the back plate is installed. Mise en garde : Les piles utilises dans ce dispositif peuvent prsenter des risques d'incendie ou de brlure chimique si elles sont mal traites. Ne rechargez pas, ne dsassemblez pas, ne faites pas chauffer et ne jetez pas au feu les piles plus de 100 C (212 F). Utilisez des piles au lithium Panasonic CR123A ou DURACELL DL123, DL 123A. L'utilisation d'autres types de piles peut prsenter des risques de feu ou d'explosion. Gardez les vieilles piles hors de la porte des enfants. Dbarrassez-vous des batteries utilises de faon approprie. Retirez les vieilles piles. Attendez 10 secondes et remplacer-les par quatre nouvelles piles. Pour viter une indication de piles faibles lorsque vous installez de nouvelles piles, les dos (2) piles doivent tre installes en de de 15 secondes aprs l'installation de la premire. Toute condition de pilles faibles qui aurait pu se produire devrait tre rtablie une fois la plaque arrire installe. REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. POUR LES LIMITES DU SYSTME DALARME AU COMPLET, REPORTEZ-

VOUS AU GUIDE DINSTALLATION DU PANNEAU DE COMMANDE Voir les instructions d'installation compltes 800-24139-

https://mywebtech.honeywell.com/. See Honeywell Installation Guide P/N 800-24139 https://mywebtech.honeywell.com/. Support / Pour de lassistance en ligne, visitez :

https://mywebtech.honeywell.com/

U.S. warranty / U.S. garantie: www.honeywell.com/security/hsc/resources/wa For patent info, see: / Pour des informations sur les brevets, voir :

www.honeywell.com/patents MyWebTech Warranty / Garantie Patents / brevets 2018 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved.

SiXC2W Convert to Wireless Module INSTALLATION INSTRUCTIONS The Honeywell SiXC2W is an eight zone hardwire to wireless converter used with controllers that support Honeywells SiX series devices. It is useful in retrofit 12-volt security system applications where existing contact wiring was used. It uses those existing wired contacts and converts them to wireless. FEATURES Provides 12-volts for devices such as motion detectors, glass breaks, etc. NOTE: Only two devices may be powered using the auxiliary output on the SiXC2W. Provides 24-hour battery backup if there are no external devices (100mA), other wise 12-hours if there are two devices attached. NOTES:

- It immediately sends a power loss signal to the controller in the event the power is lost.

- When no battery is connected, low battery message will send to control panel. GENERAL GUIDELINES The SiXC2W module uses a 5VDC power supply to charge the battery (Max wire length is 9.8 ft. (3m)). If the voltage drops to 9.5VDC a low battery will occur. NOTE: Anything lower than 4.5VDC, the SiXC2W is incapable of charging the battery; it must be replaced

- When battery is connected, and if battery voltage drops below 3.6VDC, a low battery message will send to control panel.

- When only the battery is connected, and if the battery voltage 3.4 V, system will shut down. Support one button calibration Automatic zone configuration Easy setup in three steps Cover tamper protection IMPORTANT!

Not to be used for fire, heat, or carbon monoxide detectors. Up to eight [8] hardwired zones can be handled by each SiXC2W module. Before mounting permanently, conduct the Go/No Go test (see controls instructions) to verify adequate signal strength, relocate if necessary. CALIBRATING The calibration process enables the SiXC2W to learn what zones are to be active and what value EOL resistors are used. NOTE: Unused zones that are open ARE NOT recognized and reported 1. Ensure all zones are connected and not faulted. 2. On the SiXC2W, click the top middle button. 3. Indicator LED #2 will flash Red for 1/2 second; then LED #3 turns steady Green. 4. Calibration is in process 5. DONE. The SiXC2W is calibrated and ready to enroll in the control panel. NOTES:

If the SiXC2W loses both AC and battery backup power, the zone calibration data is retained. If a resistor does exist, it MUST have a value between 1K and 10K.The unit comes with eight (8) 2.2K resistors for zones with no resistors. 1 IMPORTANT!

ONCE THE SIXC2W IS CALIBRATED, ANY CHANGE IN THE ZONE RESISTANCE THE MODULE MUST BE RE-CALIBRATED. ENROLLING For Lyric Controller 1. Set the Controller in Programming Mode and select Zone Programming. For Lyric: Program > Zones > Add New > Series Number 2. On the SiXC2W, power up:

LED #1 flashes for approximately 20 seconds LED #1 turns on LED #1 turns on for 3-seconds SiXC2W sends the information to the control and the serial number displays for loop 1 3. Edit the zone and response types for the zone and press Save. 4. To enroll additional zones, activate each loop (one per zone) when prompted for the serial number. Zone MAC #

Loop #

Zone 1 00D02D123456 Zone 2 00D02D123456 Zone 3 00D02D123456 Zone 4 00D02D123456 1 2 3 4 Example:

Zones 1-8 can be used for other SiX series devices. However, zones on the SiXC2W must align with the assigned loops on the control. 5. The controller registers the device and displays the sensor data on screen. NOTES:

Each SiXC2W has a unique mac number which enables the control panel to recognize and differentiate each zone. Further, since the SiXC2W has eight zones each zone is automatically assigned the next sequential mac number; all zones are assigned loop 1-8 respectively. FOR LYRIC GATEWAY Use AlarmNet 360 to enroll and program this sensor. FOR OTHER CONTROLS For other controls that support SiX series devices, see the controllers installation app for details NOTE: Once enrolled in a system, the SiXC2W cannot be used with another controller until it is removed from the current controller. See the Controllers instructions for details. Zone Zone 5 Zone 6 Zone 7 MAC #

Loop #

00D02D123456 00D02D123456 00D02D123456 5 6 7 8 00D02D123456 Zone 8 NOTE: Enrollment time varies depending on the signal strength between the device and the controller. When done, LED #1 is ON for 3 seconds and the control beeps to confirm enrollment. 2 TAMPER/LOW BATTERY REPORTING The SiXC2W reports this condition to the control. If a low battery or tamper condition exists all zones used on the module shows a trouble on the control. MOUNTING NOTE: This product must be installed in accordance with ANSI/NFPA 70, National Electrical Code. 1. At the existing control panel, label and remove the zone wires to be transferred to the SiXC2W. 2. Select a mounting position for the module. In most installations, the best mounting location is close to the existing control panel. remotely by extending the existing zone wires. NOTE: If needed, the SiXC2W can be located If needed, you may cut and splice (observing good workmanship) the battery wires and extend their length up to 3 ft. (0.9 meters) using 22 AWG wire, minimum. NOTE: DO NOT mount inside the control panel 3. Install the center screw to secure the back tamper to or other metal enclosure. the wall. 4. Attach using the supplied screws. 5. Ensure the wiring is complete. Use cable ties as necessary to secure wiring. Plug the power transformer into an un-switched outlet and secure with screw. Then attach the backup battery wires. IMPORTANT:

The first battery test occurs 1 hour after power up. To quickly verify a good backup battery, unplug and then plug back in the power supply; the system will perform a battery test within 1 minute. NOTES:

All zones used MUST have an EOL resistor. EOL resistor values must be from 1k to 10k ohms.

(Eight 2.2k ohm resistors are included for those panels not using any resistors.) If the existing installation zones have EOL resistors

(from 1k to 10k ohms) they may remain. When the end of line resistor value is disabled, the SIXC2W will not look for any end of line resistor value, however if there are still end of line resistors in place (up to 10K ohms) they will not need to be removed unless the installer decides to do so. For a NC loop without an EOL resistor, you must add one in series with the loop. Preferably it should be located at the end of the loop furthest away from the control panel for proper supervision. For a NO loop without an EOL resistor, you must add one in parallel (across) the loop. Preferably at the end of the line (EOL) for proper supervision. Signal strength: Rang of 1-4 bars (green), should be a minimum 1 green bar for the zone being programmed. Four Red Bards indicate poor signal strength; the device should be relocated. See the controllers instruction for bar indication signal strength values. Icon Description 4 Green Bars 3 Green Bars 2 Green Bars 1 Green Bar 4 Red Bars Signal Strength Good Relocate SENSOR LOCATION FEATURE To verify the location of each SiX device in an installation, enter programming mode and select a SiX device zone. The device LED (located on the back) lights (can take up to 30 seconds). Select it again to turn the LED off or select the next device to locate. 3 SUMMARY OF CONNECTIONS LED STATUS TABLE LED #

1 (Green) 2 (Red ) 3 (Green) 4 (Green and Red) Functions Blinks once upon RF signal transmission (HW zone trigger/tamper and/or a fault message) and a slow blink for a cover tamper Quickly blinks during the enrollment/deletion process Blinks 1s / 1s off when module needs calibrating Steady on when the module has been calibrated. Green: 5VDC Power from the plug-in transformer is present Red (blinking 1sec on / 1 sec off @ 1hz each): Running on battery, DC power not present. 4 REPLACING THE BATTERY SPECIFICATIONS Voltage Transformer Part Number ............................................................................ 300-10259 Input Voltage ....................................................................................................... 100 ~ 240VAC, 50 ~60 Hz Operating Voltage............................................................................................. 5VDC Maximum Transformer Distance .............................................................. 9.8ft. (3m) Voltage Output ................................................................................................... 12VDC @ 100mA (Up to three sets of 2024 gauge wiring) Battery/ Pile ......................................................................................................... P/N 300-10342 Environmental Operating Temp ................................................................................................. 14 F (-10C) to 140F (60C) Relative Humidity .............................................................................................. 95%, Non-condensing / 95% max. sans condensation Physical Dimensions .......................................................................................................... Length 7.0 in (178 mm) x Width 4.5 in (114 mm) x Mounting Hardware ........................................................................................ Double stick tape and screws Zone Resistance ................................................................................................ 1K to 10K Ohm EOL Resistors Zone Wiring .......................................................................................................... 1,000ft (Each Zone) NOTE: Charging the lithium battery stops when temperature is Depth 1.5 in (38mm) below 32F (0C) Radio Frequency Transmission Range ........................................................................................ 300ft (91.5m) 5 REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. POUR LES LIMITES DU SYSTME DALARME AU COMPLET, REPORTEZ-VOUS AU GUIDE DINSTALLATION DU PANNEAU DE COMMANDE. RF EXPOSURE Warning The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-

located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product procedures. Approval Listings / Approbations homologations FCC / IC - ETL Listed to UL268 & 521 cETL Listed to ULC S530 & S531 RF EXPOSURE Mise en Garde Exposition aux Frquences Radio: La/les antenne(s) utilise(s) pour cet metteur doit/doivent tre installe(s) une distance de sparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas tre situe(s) ni fonctionner paralllement tout autre transmetteur ou antenne, except en conformit avec les procdures de produit multi transmetteur FCC et ISED. Other Standards RoHS FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS dIndustrie Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles.

(2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. SUPPORT, WARRANTY, & PATENT INFORMATION For online support information, please go to Pour de lassistance en ligne, visitez : https://mywebtech.honeywell.com/

For the latest warranty information, go to / Pour les dernires informations de garantie, s'il vous plat aller : www.honeywell.com/security/hsc/resources/wa For patent information, see / Pour des informations sur les brevets, voir www.honeywell.com/patents MyWebTech Warranty Patents 800-23795w 800-23795 2/18 Rev A 2017 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved. Honeywell est une marque dpose de Honeywell International Inc. Toutes les autres marques de commerce appartiennent leurs propritaires respectifs. Tous droits rservs.