Model WTS700 / Modle WTS700 Wireless Touchscreen / cran tactile sans fil Installation and Setup Guide / Guide dinstallation et de configuration GENERAL INFORMATION The WTS700 is a wireless touchscreen that is used in conjunction with the ADTHYBWL and ADT7AIO Control Panel. Up to a total of eight (8) Touchscreens can be used on the system. The touchscreen must be enrolled in the Controller before it can be used. It communicates with the control via Wi-Fi. OPERATING THE TOUCHSCREEN For operating instructions, see the User Guide for the control panel used with this Touchscreen. RENSEIGNEMENTS GNRAUX Le WTS700 est un cran tactile sans fil qui est utilis en conjonction avec le panneau de contrle ADTHYBWL et ADT7AIO. Le systme peut prendre en charge jusqu huit (8) crans tactiles. Avant toute utilisation, l'cran tactile doit tre enregistr dans le contrleur. Il communique avec le contrleur par Wi-FiMD. UTILISATION DE L'CRAN TACTILE Pour les directives dutilisation, consultez le guide de l'utilisateur du panneau de commande utilis avec cet cran tactile. POWER BUTTON/
BOUTON DALIMENTATION SYSTEM STATUS LED/
DEL D'TAT DU SYSTME BATTERY CHARGER RECEPTACLE/
PRISE DU CHARGEUR DE LA BATTERIE Ready To Arm Ready To Arm System Tools Arm Away Arm Stay Arm Custom Zones Scenes 9:11 AM Jauary 20, 2018 DESK STAND/
SUPPORT DE TABLE PLUG-IN BATTERY CHARGER/
CHARGEUR ENFICHABLE DE LA BATTERIE POWER BUTTON/
BOUTON DALIMENTATION WTS700-003-V0 COVER PLATE OPEN INSERT BATTERY
(cover not shown for clarity)
(LINE UP WITH PINS) BATTERY
(INSERT) COVER PLATE grip-046-V0 FACE DOWN 0 V
-
2 0 0
-
0 0 7 S T W INSTALL BATTERY Place the touchpad face down and pull open the desk stand. Remove the battery cover plate. Align the contacts on the battery pack over the pins on the touchpad and press down to secure. Align the tabs on the battery cover plate and snap into place. Connect the power charger to the Touchscreen as shown and plug into a non-switchable 110VAC, 60Hz outlet for 24hrs to fully charge battery. Press and hold the Power button to turn on. ENROLLING THE TOUCHSCREEN 1. Use the Controller installer programming app and go to the Touchscreen section, then click ADD. The screen displays, Starting Up, Please Standby and then enters Pairing Mode. Press Pair and the Touchscreen automatically attempts to pair with the Controller. If enrollment is not successful, press any of the keys on the Touchscreen to restart the pairing process or disconnect and reconnect power. INSTALLER LA BATTERIE Placez le pav tactile vers le bas et ouvrez le support de bureau. Retirez le couvercle de la batterie. Alignez les contacts de la batterie sur les broches du pav tactile et appuyez dessus pour les scuriser. Alignez les languettes sur le couvercle du compartiment de la pile et enclenchez-le. Branchez le chargeur lcran tactile comme illustr, puis branchez-le dans une brise sans interrupteur de 110 VCA, 60 Hz, durant 24 heures pour obtenir une charge complte de la batterie. Appuyez et maintenez enfonc le bouton d'alimentation pour activer. ENREGISTRER L'CRAN TACTILE 1. Utilisez lapplication de programmation du contrleur et allez la section cran tactile , puis cliquez sur ADD (Ajouter). Lcran affiche Starting Up, Please Standby (Dmarrage, veuillez patienter), puis entre en mode jumelage. Appuyez sur Pair (Jumeler) et l'cran tactile tentera de sapparier automatiquement au contrleur. Si lenregistrement choue, appuyez sur nimporte quelle touche de lcran tactile pour relancer le processus dappariement ou dbranchez puis rebranchez le bloc dalimentation. 2. After successful pairing, Touchscreen displays, Programming Mode Please Standby, until exit of program mode. System then displays Ready to Arm. When enrolled, the Touchscreens ID number appears on the Controllers screen. 3. After enrollment, program and save the Touchscreens zone options (zone descriptor, etc.) at the Controller. NOTE: Make sure to assign a descriptor to the Touchscreen for easy identification when Touchscreen events occur. IMPORTANT: Once enrolled, the Touchscreen cannot be used with another control panel until it is un-enrolled (deleted) from the current controller. See the Smart Controllers Programming Guide for details on removing devices. SPECIFICATIONS:
Physical: 7.68 W x 4.76 H x 0.708 D
(195mm x 121mm x 18mm) Frequency of Operation: Wi-Fi Battery (included): 3.8V, 2000mAh, Limited charge voltage: 4.35 Replacement P/N 300-06868 Battery Charger (included): 5V 1A, Micro USB RF EXPOSURE Warning The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter. 2. Une fois lappariement russi, l'cran tactile affiche Programming Mode Please Standby (Mode programmation, veuillez patienter) jusqu ce que lappareil quitte le mode de programmation. Ensuite, le systme affiche Ready to Arm (Prt armer). Une fois l'cran tactile enregistr, son numro didentification saffiche sur lcran du contrleur. 3. Aprs lenregistrement, programmez et enregistrez les options de zone de lcran tactile (descripteur de zone, etc.) sur le contrleur. REMARQUE : assurez-vous dattribuer un descripteur lcran tactile pour faciliter lidentification lorsque des vnements lis lcran tactile se produisent. IMPORTANT : une fois enregistr, lcran tactile ne peut pas tre utilis avec un autre panneau de commande tant quil nest pas dsinscrit
(supprim) du contrleur actuel. Consultez le guide de programmation du contrleur intelligent pour en savoir plus sur la suppression des priphriques. SPCIFICATIONS :
Caractristiques physiques: 195 mm l x 121 mm H x 18 mm P
(7,68 po x 4,76 po x 0,708 po) Frquence de fonctionnement: Wi-FiMD Batterie (fournie): 3,8 V, 2 000 mAh, tension de chargement limite : 4,35. Chargeur de batterie (fourni): 5 V 1 A, Micro USB No de pice de rechange 300-06868 Mise en Garde Exposition aux Frquences Radio : La/les antenne(s) utilise(s) pour cet metteur doit/doivent tre installe(s) une distance de sparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas tre situe(s) ni fonctionner paralllement tout autre transmetteur ou antenne, except en conformit avec les procdures de produit multi transmetteur FCC et ISED. FEDERAL COMMUNICATIONS COMMISSION & ISED STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information. This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
If using an indoor antenna, have a quality outdoor antenna installed. Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control panel. Move the antenna leads away from any wire runs to the receiver/control panel. Plug the receiver/control panel into a different outlet so that it and the radio or television receiver are on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. ISED CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC / ISED STATEMENT This device complies with Part 15 of the FCC Rules, and ISEDs license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS dISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS ON LIMITATIONS OF THE ENTIRE ALARM SYSTEM. For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa/
For patent information, see www.honeywell.com/patents SUPPORT: For technical support, call 1-877-748-7628, option 3. For documentation, call Customer Service at:
1-800-238-2727 (1-800-ADT-ASAP). Pour les Limites du systme d'alarme en entier, consultez le guide dinstallation du panneau de commande avec lequel ce dispositif est utilis. Pour voir les toutes dernires informations relatives la garantie, veuillez consulter: www.honeywell.com/security/hsc/resources/wa/
Pour consulter les informations relatives aux brevets, rendez-vous sur www.honeywell.com/patents SUPPORT: For technical support, call 1-877-748-7628, option 3. For documentation, call Customer Service at: 1-800-238-2727 (1-
800-ADT-ASAP). ADT Security Services 1501 Yamato Rd Boca Raton, FL 33431 Copyright 2018 800-24298u 800-24298 4/18 Rev A