all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 3 |
|
Installation Manual | Users Manual | 2.41 MiB | ||||
1 2 3 |
|
Quick User Guide | Users Manual | 2.62 MiB | ||||
1 2 3 | Test Report | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | External Photos | |||||||
1 2 3 | Internal Photos | |||||||
1 2 3 | ID Label/Location Info | |||||||
1 2 3 | Test Setup Photos | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | RF Exposure Info | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Setup Photos | |||||||
1 2 3 | Test Setup Photos | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Report |
1 2 3 | Installation Manual | Users Manual | 2.41 MiB |
Lyric TM Gateway Ref: LCP300-L/LCP300-LC 800-21666 10/16 Rev. A Installation and Reference Guide Lyric Gateway Installation and Reference Guide RECOMMENDATIONS FOR PROPER PROTECTION The Following Recommendations for the location of fire and burglary detection devices help provide proper coverage for the protected premises. Recommendations for Smoke and Heat Detectors With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #72 noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: For minimum protection a smoke detector should be installed outside of each separate sleeping area, and on each additional floor of a multi-floor family living unit, including basements. The installation of smoke detectors in kitchens, attics (finished or unfinished), or in garages is not normally recommended. For additional protection the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages. In addition, we recommend the following:
Install a smoke detector inside every bedroom where a smoker sleeps. Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the sleeper if the door is closed. Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air conditioners or humidifiers) are used. Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long. Install smoke detectors in any room where an alarm control is located, or in any room where alarm control connections to an AC source or phone lines are made. If detectors are not so located, a fire within the room could prevent the control from reporting a fire or an intrusion. THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE SOUNDING OF FIRE NOTIFICATION APPLIANCES. Recommendations for Proper Intrusion Protection For proper intrusion coverage, sensors should be located at every possible point of entry to a home or premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system. This will ensure that alarm signals can be sent to the alarm monitoring station in the event that the communications are out of order (if connected to an alarm monitoring station). This Honeywell security system is designed for use with devices manufactured or approved by Honeywell for use with the system. The security system is not designed for use with any device that may be attached to the system's control or other communicating bus if Honeywell has not approved such device for use with the system. Use of any such unauthorized device may cause damage or compromise the performance of the security system and affect the validity of the end users Honeywell limited warranty. When you install devices that have been manufactured or approved by Honeywell, you give the end user the assurance that these devices have been thoroughly tested to ensure optimum performance when used with this Honeywell security system.
- 2 -
Lyric Gateway Installation and Reference Guide Table of Contents System Features ............................................................................................................................................................................................ 5 Installing the Control .................................................................................................................................................................................... 7 Battery Installation .......................................................................................................................................................................................... 7 Battery Selection ..................................................................................................................................................................................... 7 Installing the Rechargeable Backup Battery ................................................................................................................................. 7 Replacing the Rechargeable Backup Battery ............................................................................................................................... 7 Wall Mounting .................................................................................................................................................................................................. 8 Desktop Mounting .......................................................................................................................................................................................... 9 Replace the Back Plate ......................................................................................................................................................................... 9 Install the Desk Stand ........................................................................................................................................................................... 9 AC Power .......................................................................................................................................................................................................... 10 Wiring Overview ............................................................................................................................................................................................ 10 Make Electrical Connections ............................................................................................................................................................. 10 Communications Modules ........................................................................................................................................................................... 11 Communications Module 24-Hour Standby power ................................................................................................................... 11 Install and Configure Communications Module .................................................................................................................................. 11 Installing the Cellular Module ............................................................................................................................................................. 11 Checking Signal Strength ................................................................................................................................................................... 12 Wireless Zones .............................................................................................................................................................................................. 13 General Information ...................................................................................................................................................................................... 13 Zones .......................................................................................................................................................................................................... 13 Range ......................................................................................................................................................................................................... 13 Transmitters ............................................................................................................................................................................................. 13 House Identification .............................................................................................................................................................................. 13 Transmitter Supervision ...................................................................................................................................................................... 13 Transmitter Input Types ...................................................................................................................................................................... 13 Transmitter Battery Life ...................................................................................................................................................................... 13 RF Transmitter Loop Numbers ......................................................................................................................................................... 14 Mechanics of Programming .................................................................................................................................................................... 15 Navigating Menus .......................................................................................................................................................................................... 15 Touch-screen Display........................................................................................................................................................................... 15 Navigation Keys ..................................................................................................................................................................................... 16 Home Screen ........................................................................................................................................................................................... 16 Security Screen ...................................................................................................................................................................................... 17 Master User Tools Screen ................................................................................................................................................................... 17 Programming .................................................................................................................................................................................................. 18 Enter Installer Programming Mode ................................................................................................................................................. 18 Loading Factory Defaults ........................................................................................................................................................................... 19 Select a Default Configuration ......................................................................................................................................................... 19 Exit Programming Mode ............................................................................................................................................................................. 19 Zone Response Type Definitions ......................................................................................................................................................... 20 General Information ..................................................................................................................................................................................... 20 System Operation ....................................................................................................................................................................................... 22 Key/Touchscreen Operation .................................................................................................................................................................... 22 Panic Key/Icons ............................................................................................................................................................................................. 22 Security Codes ............................................................................................................................................................................................... 22 Installer Code ......................................................................................................................................................................................... 22 Master Code ........................................................................................................................................................................................... 22 Enter/Change the Master Code by Installer ............................................................................................................................... 22 Secondary User Codes ....................................................................................................................................................................... 22 Reset Master Code ............................................................................................................................................................................... 23 Security Code Notes ........................................................................................................................................................................... 23 System Displays ............................................................................................................................................................................................ 24 Zone Status Displays ................................................................................................................................................................................... 24 Audio Alarm Verification (Two-Way Voice Feature) ..................................................................................................................... 25 Activation ................................................................................................................................................................................................ 25 Operator Commands .......................................................................................................................................................................... 25 Event Log ........................................................................................................................................................................................................ 26 Contact ID Event Log Codes ............................................................................................................................................................ 26 Central Station Messages .......................................................................................................................................................................... 27 Testing the System .................................................................................................................................................................................... 28
- 3 -
Lyric Gateway Installation and Reference Guide Table of Contents (Continued) Test Modes ...................................................................................................................................................................................................... 28 Testing the System....................................................................................................................................................................................... 28 Armed System Test ..................................................................................................................................................................................... 28 Zone Discovery Mode ................................................................................................................................................................................. 29 Rebooting the System ................................................................................................................................................................................ 29 Programming Default Values ............................................................................................................................................................... 30 Zone Assignment/Alarm Response Type for Configuration 1 ..................................................................................................... 32 Zone Assignment/Alarm Response Type for Configuration 2 .................................................................................................... 33 Zone Assignment/Alarm Response Type for Configuration 3 and 4 ....................................................................................... 34 Zone Response Type Matrix .................................................................................................................................................................. 35 Regulatory Agency Statements ........................................................................................................................................................... 36 Limitations of this System Statement ............................................................................................................................................... 37 Agency Notices ............................................................................................................................................................................................ 38 SIA Quick Reference Guide .................................................................................................................................................................... 39 Specifications ................................................................................................................................................................................................ 39 Glossary .......................................................................................................................................................................................................... 40 Contacting Technical Support ............................................................................................................................................................... 41 Index .................................................................................................................................................................................................................. 42 Summary of Connections Diagram ..................................................................................................................................................... 43 Warranty Information ............................................................................................................................................................ Rear Cover Lyric Lock This system supports Lyric Lock, an advanced feature designed to keep it functioning optimally. Lyric Lock capabilities include: the ability to interact with Honeywell and your companys network for the setup and programming of system features, support for remote software updates and the ability (when enabled) to enhance the end users security by preventing unauthorized takeover of the system by another monitoring company. In the event that the end user wishes to authorize another company to take over the system, the end user may request that Honeywell remotely disable Lyric Lock. Honeywell will require documentation that the end user has attempted to contact your company three times and that your company has failed to respond, or failed to agree to the end users request.
- 4 -
Lyric Gateway Installation and Reference Guide System Features The Lyric Gateway is a self-contained, rechargeable wireless control/communicator that features easy installation and usage. A built-in speaker provides voice annunciation of system status along with voice descriptors of each zone. An internal module allows the controller to communicate with the Central Station via the Internet or (if installed) Cellular Wireless. ETL Lyric Gateway is not intended for UL985 Household Fire applications unless a 24-hour backup battery (p/n 300-03866-AIO) is installed. System Features Message Center (for user recorded messages) Voice Announcement of System and Zone Status Ten User-selectable Chime Sounds Automatic Stay Arming Night Stay Arming 49 User Codes (Installer, Master, Guest, Duress) Panic Functions (Police, Fire, Medical) Programmable Reminders Video Camera Control (requires WiFi connection) Supports Mobile Devices (Tablet, iPAD, etc.) that duplicate functions of the Lyric Gateway (i.e.; Security, Web Content Home Automation and Video Control) Home Automation Integrated Z-Wave Support Control up to 72 Z-Wave Home Automation Devices including:
- Thermostats (up to 8)
- Door Locks (up to 6)
- Devices (outlets, switches, lamps/appliances) (up to 60)
- Garage Doors (up to 4)
- Water Valves (up to 4) Supports Z-Wave Network Wide Inclusion (NWI) Mode 100 programmable Smart Actions Up to 150 scheduled events Zones and Devices 4 Panel Panic Zones 64 Wireless Zones (5800 and SiX Series transmitters) Four Garage Door Zones 32 Wireless Buttons (Wireless Key) Zones (5800 and SiX Series transmitters) Eight (SiX Series) Wireless Keypad Zones Resident Monitor Zone Types Built-in Case Tamper 12 Temperature Zones Communication ADEMCO Contact ID Integrated WiFi Support Cellular (GSM or CDMA) Central Station communication WiFi Central Station communication Ethernet Central Station communication Two-way Voice Communication Supports AlarmNet 360 Remote Services TM
- 5 -
Lyric Gateway Installation and Reference Guide System Features (Continued) System Power Primary Power: Plug-in Power Supply, 110VAC to 9VDC, 2.5A output p/n 300-04705V1 (300-4063V1 in Canada) Backup Battery: Rechargeable Nickel-metal Hydride Battery Pack rated at 7.2Vdc. (p/n 300-03864-AIO or 300-03866-AIO Alarm Output Built-in Sounder Steady Output for burglary/panic Temporal (3) Pulse Output for fire alarms Temporal (4) Pulse Output for carbon monoxide alarms Audio Alarm Verification (AAV) Programming Options stored in EEROM Can be uploaded, downloaded or controlled via AlarmNet 360TM using capable Cellular or WiFi Communications Module Flash Downloading Other Features Exit Error feature (detects difference between an actual alarm and exit alarm caused by leaving a door open after the exit delay expires) Event Log Storage (total 6,000 events) RF Jam Detection Advanced Protection Logic (APL) (Minimizes the likelihood of the system being disabled before notification can be sent to the Central Station indicating that the premises have been compromised.) Lyric Lock (Customer Retention Logic) Dealer selectable Lockout (anti-takeover) feature Dealer/Central Station Messages (requires Total Connect Service)
- 6 -
Lyric Controller Installation and Reference Guide Installing the Gateway Battery Installation The Lyric Gateway is equipped with an integral, replaceable, rechargeable battery pack rated at 7.2Vdc. In the event of an AC power loss, the system is supported by the long life backup battery that is supervised for connection and for low voltage conditions. If the battery is missing, or a low battery condition is detected, a low battery message is displayed on the smart device and Alert will flash red on the Gateway. In addition, a System Low Battery report is sent to the Central Station. In addition, the system will beep once every 45 seconds to audibly indicate a low battery condition (press any key to stop the beeping). Select the appropriate battery pack, based on the installations requirement, and install the battery pack. Follow the steps and refer to the figure below to install and connect the battery. Battery Selection Select the appropriate battery pack, based on the installations requirement, and install the battery pack. Battery Part Number 300-03864-AIO 300-03866-AIO Battery StandbyTime Low Battery Notification 4-hours (minimum) 24-hours (minimum) Approximately 1-hour before battery depletion At least 1-hour before battery depletion Insert the battery pack into gateway. Replacing the Rechargeable Backup Battery 1. 2. Close the hinged battery retainer. 3. Connect the battery pack connector to the receptacle on the gateway. 4. Align the slots on the back of the controller with the hooks on the rear cover/wall mount as shown below. 5. Once attached, insert the screw to secure the rear cover/wall mount. 6. Plug the power supply into a 24-hour, 110VAC unswitched outlet. Upon power-up, the LEDs will flash alternately. 7. When the power-up sequence is complete, the green Disarmed LED and the green shield will be lit. Rechargeable batteries may take up to 48-hours to fully charge. The Low Battery message should clear within four hours or by entering Test Mode. Replacing the Rechargeable Backup Battery 1. When battery replacement is required, at the Master User Tools Menu screen select the Advanced icon. 2. Select Install Backup Battery and follow the displayed steps to replace the battery or follow the steps below. Remove the battery 1. Remove the screw securing the gateway to the rear cover/wall mount (if used). 2. Remove the back case or remove the gateway from the rear cover/wall mount.
- 7 -
Lyric Gateway Installation and Reference Guide Installing the Gateway (Continued) 3. Disconnect the battery pack connector from the receptacle on the back of the gateway. 4. Open the hinged battery retainer. 5. Remove the battery pack from the Gateway. Install the replacement battery 1. Install a replacement battery pack (LCP500-4B [p/n 300-03864-AIO] OR LCP500-24B [p/n 300-03866-
AIO]) into the gateway. 2. Close the hinged battery retainer. 3. Connect the battery pack connector to the receptacle on the gateway. 4. Align the slots on the back of the controller with the hooks on the rear cover/wall mount as shown below. 5. Once attached, insert the screw to secure the rear cover/wall mount. 6. Plug the power supply into a 24-hour, 110VAC unswitched outlet. Upon power-up, the LEDs will flash alternately. 7. When the power-up sequence is complete, the green Disarmed LED and the green shield will be lit. NOTE: If a Cellular Communication Module is being installed, verify the modules signal strength before selecting a final mounting location. Refer to Checking the Signal Strength in the Communications Module section. Wall Mounting NOTE: When selecting a location for the Lyric Controller, be sure to provide a separation of at least 10 feet between 2.4GHz devices such as Wi-Fi Routers/Access Points. For wall mounting follow the steps and refer to the figure below. 1. Feed the field wiring through the appropriate openings in the wall mount. 2. Attach the wall mount to a sturdy wall using the four provided screws. 3. 4. Align the slots on the back of the controller with the hooks on the wall mount as shown below. 5. Once attached, insert the screw to secure the Lyric to the wall mount. If required, install an additional mounting screw in the case tamper.
- 8 -
Lyric Gateway Installation and Reference Guide Installing the Gateway (Continued) Desktop Mounting NOTE: When selecting a location for the Lyric Gateway, be sure to provide a separation of at least 10 feet between 2.4GHz devices such as Wi-Fi Routers/Access Points. The desk Stand can be installed in two positions that provide a viewing angle of 30 degrees or 60 degrees. Follow the steps and refer to the figures below. Install Desk Stand 1. Align the slots on the back of the gateway with the hooks on the desk stand as shown below. 2. Insert the stand into the slots on the rear case to provide the desired viewing angle and slide up to lock in place.
- 9 -
Lyric Gateway Installation and Reference Guide Installing the Control (Continued) AC Power The Lyric Gateway is powered by a 110VAC, 60 Hz/9 Volt DC, 2.5 Amp Plug-in Power Supply, 300-04705V1
(300-04063V1 in Canada). Refer to the wiring table below for wire gauge and length. Use only the 300-04705V1 (300-04063V1 Canada) Power Supply. Do not plug the power supply into the AC outlet until after all wiring connections have been made. Wiring Overview The following summarizes the electrical connections associated with the Lyric Gateway. Follow the steps and refer to the figure below when making connections. Refer to the Summary of Connections diagram for additional information. Make Electrical Connections 1. Temporarily hang the controller from the hook on the wall mount. 2. Connect the male end of the receptacle on the Gateway. 3. Align the slots on the back of the Gateway with the hooks on the rear cover/mounting bracket. 4. Once attached, insert the screw to secure the Gateway to the rear cover/mounting bracket . 5. Connect the flying leads of the provided power supply cable to the + and terminals on the power supply
(p/n 300-04705V1 or 300-04063V1). 6. Plug the power supply into a 24-hour, 110VAC unswitched outlet. Upon power-up, the System Standby!
screen will be displayed. WIRING TABLE Maximum Distance Between Power Supply and Controller Wire Gauge Up to 8 feet (2.44 m) Up to 13 feet (3.96 m) Up to 20 feet (6.1 m)
# 22
# 20
# 18
- 10 -
Lyric Gateway Installation and Reference Guide Installing the Gateway (Continued) The LYRIC-CDMA Communications Module is only available in the continental United States, Alaska and Hawaii. Communication Modules The Lyric Gateway supports Central Station reporting using wireless/cellular and WiFi communications devices. They also support upload/download programming capability via the Internet. This allows site maintenance independent of Central Station monitoring, and modification to sites globally via the Internet. Refer to the Quick Installation Guide (p/n 800-21668) for information regarding programming and registration. Additionally, an internal Z-Wave module allows the Lyric Gateway to support Home Automation functions. (refer to the Gateway Guide (p/n 800-16078 for additional information.) The controllers are compatible with the following AlarmNet Communication Modules:
Model LYRIC-3G LYRIC-CDMA Communications Module 24-Hour Standby Power If 24-hour standby is required, the Super High Capacity battery (p/n 300-03866-AIO) must be installed. Description GSM Cellular Communications Module CDMA Cellular Communications Module WARNING: The Lyric Gateway must be installed to provide a separation distance of at least 7.8 in (20 cm) from all persons and not co-located or operated in conjunction with any other transmitter except in accordance with FCC multi-transmitter product procedures. RF Exposure Install and Configure Communication Module Follow the steps and refer to the figure below to install the Communications Module. Installing the Cellular Communications Module 1. At the the Master User Tools Menu Programming screen select Advanced. 2. Select Install Cellular Module and follow the prompts displayed on the smart device or follow the steps below. 3. Remove Gateway upper cover (bezel). 4. Remove the screw securing the module to the Gateway (if installed). 5. Remove the existing Cellular Communications Module (if installed). 6. 7. Ensure that the Communications Module is properly seated into the Gateway and secure the module with Install the Cellular Communications Module into the Gateway. the provided screw (if required). Insert the cover (bezel) into the Gateway 8. 9. Slide the side cover (bezel) down to lock it in place and secure the Communications Module. 10. Select OK to complete the installation. NOTE: The Communication Path will be dynamically adjusted when a Cellular Communication Module is installed or removed. 11. Enable the Communications Module, configure alarm reporting and module supervision and register the device. Refer to the Program Communicator and Communications Diagnostics sections in the Programming Guide (p/n 800-18077). OR Log on to the AlarmNet 360TM website (http://alarmnet360.com). The Communications Module must be registered with AlarmNet 360TM before downloading or alarm reporting can take place.
- 11 -
Lyric Gateway Installation and Reference Guide Installing the Gateway (Continued) Communication Modules Checking Signal Strength When choosing a suitable mounting location, check the communications modules signal strength to ensure proper operation. For most installations, using the modules internal antenna, mounting the Lyric Gateway as high as practical, and avoiding large metal components provides adequate signal strength for proper operation. To check signal strength, perform the following test. Check Signal Strength Lyric -3G Signal Strength RSCP (3G) Good .......................................... -20 to -90 dBm OK ................................................ -91 to -100 dBm Marginal ................................... -101 to -106 dBm Bad ........................................... -107 to -120 dBm RSSI (2G) Good ........................................... -20 to -89 dBm OK ................................................ -90 to -98 dBm Marginal .................................. -99 to -104 dBm Bad .......................................... -105 to -120 dBm Lyric -CDMA Signal Strength RSSI Good ........................................... -20 to -90 dBm OK ................................................ -91 to -100 dBm Marginal ................................... -101 to -106 dBm Bad .......................................... -107 to -120 dBm 1. With the System in the Installer Programming mode, select the Comm. Diagnostics button and then select the Cellular Information button. The Cellular Information will be displayed. The signal strength is displayed (in dBm) as RSCP if the Lyric-3G module is operating on the 3G Network or RSSI if the module Lyric-3G module is operating on the 2G Network and for the Lyric-CDMA module. 2. Compare the displayed RSCP or RSSI number to the correct Signal Strength Guide at right to ensure adequate signal strength. If necessary, relocate the Controller to obtain better signal strength (select Cellular Information again to refresh the reading). 3. If adequate signal strength cannot be achieved, External Antenna Kit model Cell-ANTST should be used.
- 12 -
Lyric Controller Installation and Reference Guide Wireless Zones General Information Zones The Lyric Gateway supports up to 64 total wireless zones using 5800 and SiX Series transmitters, and wireless keys. Range The built-in RF receiver can detect signals from wireless transmitters within a nominal range of 200 feet. Transmitters 5800 and SiX Series transmitters have built-in serial numbers that must be entered into the system via AlarmNet 360TM. Each transmitter's zone number is also programmed into the system in the Zones programming section. Some transmitters, such as the 5816 can support more than one "zone" (referred to as loops or inputs). On the 5816, for example, the wire connection terminal block is loop 1; the reed contact is loop 2. Each loop must be assigned a different zone number. For 5800 Series wireless keys such as the 5804E, 5834-4 and 5878, you must assign a unique zone number to each individual button used on the transmitter. Each button on the transmitter also has a pre-designated loop or input number, which is automatically displayed. ETL The 5816 Transmitters do not have EOL supervision of their loop wiring, which must not exceed 3 feet. The 5800PIR-OD, 5800SS1, 5804E, 5814, 5821, 5877 and 5878 wireless transmitters have not been evaluated by ETL. House Identification If a RF House ID (RF House Code) is required to establish proper communication, the same two-digit code (01 31) must be programmed in the Lyric, and the device. Refer to the System Type programming section in the Lyric Gateway Programming Guide (p/n 800-18077). An RF House ID is not necessary for 5800 Series transmitters and the entry should be left at 0 (default) in those cases. Transmitter Supervision With the exception of some transmitters/keypads that may be carried off-premises (5804E, 5834-4 and SiXFOB), each transmitter is supervised by a check-in signal that is sent to the receiver at 7090 minute intervals. If at least one check-in is not received from each supervised transmitter within a 12-hour period, the
"missing" transmitter zone number(s) and "Supervision" will be displayed. The supervision for a particular transmitter in the system that may also be carried off the premises may be turned off by entering it as an Unsupervised type. For additional information, refer to the Zones programming section in the Lyric Gateway Quick Installation Guide (p/n 800-21668). 5800 and SiX Series transmitters have built-in tamper protection and will annunciate as a fault condition if covers are removed. In Canada the RF supervision period is 3-hours for Fire zones and 12 hours for all other zone types. Transmitter Input Types Each transmitter has one or more unique factory-assigned input (loop/5800 Series or service/SiX Series) ID codes. Each of the inputs requires a programming zone (e.g., a 5804E's four inputs require four button zones). Transmitters can be entered as one of the following types (see transmitters instructions for appropriate Supervision type):
Type Supervised Unsupervised Button Description Sends periodic check-in signals, as well as fault, restore, and low battery signals. The transmitter must remain within the receiver's range. Sends all the signals that the Supervised type does, but the controller does not supervise the check-in signals. The transmitter may therefore be carried off-premises. Sends only fault signals. Do not send low battery signals until being activated. The transmitter is unsupervised and may be carried off-premises. Transmitter Battery Life Batteries in the wireless transmitters may last from 47 years, depending on the environment, usage, and the specific wireless device being used. Factors such as humidity, high or low temperatures, as well as large swings in temperature may all reduce the actual battery life in a given installation. The wireless system can identify a true low battery situation, thus allowing the dealer or user of the system time to arrange a change of battery and maintain protection for that point within the system. Button-type transmitters should be periodically tested for battery life. The 5804E, 5834-4, 5878 and SiXFOB button transmitters have replaceable batteries.
- 13 -
Lyric Gateway Installation and Reference Guide Wireless Zones (Continued) RF Transmitter Loop Numbers
(Refer to this information when programming 5800 Series transmitters) The following illustration shows the compatible transmitters, their associated input types and loop designations. Notes: (1) The 5806W3 smoke detector must be used in SIA applications.
(2) Button type devices send only fault and low battery signals; no restore or check-in signals.
(3) The 5804E and 5834-4 encrypted (High-Security) devices must be activated while the system is in Supervised RF devices send periodic check-in signals, faults, restore and low battery signals. Go/No-Go Test Mode. Refer to the transmitters Installation Instructions for complete details. The system will confirm the enrollment of the encrypted device by beeping two times.
(4) The 5800PIR-OD, 5800SS1, 5804E, 5814, 5821, 5877, and 5878 wireless transmitters have not been evaluated by ETL.
- 14 -
Lyric Controller Installation and Reference Guide Mechanics of Programming Navigating Gateway Keypad Gateways keypad can be used for Basic Security Functions. The keypad provides a number of functions and indicators. The System Status Shield is lit Green when the system is ready or flashes Red when it is not. When the system is armed the System Status Shield is lit Red. Refer to the table below for additional indications and functions. Additional functions are available via the My Home or Total Connect App or the associated websites. Key Description System Status Shield System status is displayed when the shield is lit as follows:
Green (steady) Ready to Arm Red (steady) System is Armed Red (slow flash) Entry/Exit delay countdown Red (rapid flash) System is in Alarm White (steady) Waiting for User Code entry Arm gateway in Away mode (LED steady red when selected) Arm gateway in Home mode (LED steady red when selected) ARMED Away ARMED Home Disarmed Disarm Gateway (LED flashes green until code Alert Cancel is entered, then turns steady green) Flashes red when an alert condition exists. Select to hear condition Cancel User Code entry or Emergency
(Flashes white during an emergency) Emergency Activates Emergency keys Fire key - Initiates panic fire alarm within 5 seconds of activation. Police key - Initiates panic police alarm within 5 seconds of activation Medical key - Initiates panic medical alarm within 5 seconds of activation LYRICTM Gateway Gateway Menu Mode Entering the Master User Code or Installer Code on the Gateway keypad will provide access to Menu Mode. Enter Menu Mode: Enter Master User or Installer Code + 1 1. The system will announce the menu options based on the code that was entered. Code Entered Menu Option (System Annoucement) Press 20 to delete all enrolled MyHome apps Press 21 to enter MyMome app Enroll Mode Press 31 to enter Access Aoint mode Press 31 to enter Access Point mode Press 51 to enter Go/No-Go Test mode Master User (1234) Installer (4112)
- 15 -
Lyric Gateway Installation and Reference Guide Mechanics of Programming (Continued) Touch-screen Display The MyHome Gateway App is used to display screens on the smart device touch-screen. Variable icons and text are displayed on screens. The screen displays status icons and associated text, the current time and date, system status information and menu choices. The Menu area includes a list of commands, or choices that apply to the current selection. The status area provides information about various system events and colored text also provides an indication of system status. A Home Screen is displayed whenever the App is opened. Navigation Keys Navigating through the screens is accomplished by lightly touching the icons or menu items on the smart device touch-screen. Once activated, the Gateway advances to the next screen. Selecting the key or the Home
(cancel) key will return you to the previous screen or the home screen (as applicable) at any time. By touching
(selecting) an icon or key the system, depending on the function, advances to another screen, toggles between options or scrolls through multiple options that can be selected. The system provides a prompt when a specific input is required. Note: You may find it convenient to adjust the volume setting before entering the Program Mode. This will allow you to clearly hear the feedback announcements or system beeps from the systems built-in speaker. To adjust the volume, select Settings icon on the Home screen. Adjust the volume using the slide displayed on the Settings screen and then select Save to accept. Home Screen System Status is displayed at the top of screen. In addition to the system status, the Home Screen displays the current date and time and Security, Automation, TC Video, Smart Scenes and Settings icons. When Total Connect Services are connected and web content is enabled the current weather forecast and a 5-Day Forecast button. Gateway Home Screen with Total Connect Services Icon Function Provides access to Security Screen Provides access to Automation Screen Provides access to Video Screen Provides access to Smart Scenes Programming Screen Provides access to System Settings Screen Security Automation TC Video Smart Scenes Settings 5-Day Forecast Provides access to local 5-Day Weather Forecast Screen Weather Provides local forecast and severe weather alerts
- 16 -
Lyric Controller Installation and Reference Guide Mechanics of Programming (Continued) Navigating Menus Security Screen System Status is displayed at the top of each screen and the time and date are displayed at the top left side of the Security Screen. The Security Screen displays the system status and selection icons. The displayed pages and options may vary slightly depending upon the devices and services that are installed in or connected to the system. Security Screen Function Selection Arm Away Arm Home Arm Custom System Tools Used to Arm the system in Away mode. Used to Arm the system in Home mode. Used to Arm the system in Custom mode. Provides information about system status. Provides access to Installer and User Programming Menus (Master User Code required for access). Provides access to Message Center. Provides access to Zone information and options. Message Zones Master User Menu Screen The Master User Menu screen provides access to the User configurable features. Entering the Master User Code is required to access the User Tools Menu. Master User Menu Screen
- 17 -
Lyric Gateway Installation and Reference Guide Mechanics of Programming (Continued) Programming If the system is Armed or in Alarm, the Tools icon will not be functional. The system must first be disarmed. Master User Features SCREEN ACTION 1. Select the Security icon. 2. Select Tools icon. 3. Enter the Master User Code 1234 on the displayed keypad. 4. Select one of the following options:
System Information Install Cellular Module Install Backup Battery Walk Test Comm. Test Reboot Update Sensor Firmware Update Keypad Firmware 5. The system advances to the screen for the selected option. Master User Menu Screen Exit Programming Mode 1. Select the key to exit the current screen OR select the Home key to return to the Home Screen.
- 18 -
Zone Response Type Definitions General Information During programming, you must assign a zone type to each zone, which defines the way in which the system responds to faults in that zone. Zone types are defined below. Lyric Controller Installation and Reference Guide Type Not Used Entry/Exit 1
(Burglary) Entry/Exit 2
(Burglary) Perimeter
(Burglary) Interior, Follower Trouble by Day/
Alarm by Night 24-hour Silent Alarm Function Used to program a zone that is not used. Usually assigned to sensors or contacts on primary entry and exit doors. Usually assigned to sensors or contacts on secondary entry and exit doors that might be further from the keypad (typically used for a garage, loading dock, or basement door). Usually assigned to all sensors or contacts on exterior doors and windows Usually assigned to a zone covering an area
(i.e.: foyer, lobby, or hallway) that must be passed upon entry (after faulting the entry/exit zone) to reach the keypad. Provides an instant alarm if the entry/exit zone is not violated first, and protects an area in the event an intruder has hidden on the premises before the system is armed, or gains access through an unprotected area. Usually assigned to a zone that covers a sensitive area (i.e.: stock room, drug supply room, etc.) It can also be used on a sensor or contact in an area where immediate notification of an entry is desired. Usually assigned to a zone containing an Emergency button (silent emergency). 24-hour Audible Alarm Usually assigned to a zone containing an Emergency button (audible emergency). 24-hour Auxiliary Alarm Silent Burglary Local Alarm Usually assigned to a zone containing a button for use in personal emergencies or to a zone containing monitoring devices
(i.e.: water or temperature sensors, etc.). Usually assigned to sensors or contacts on exterior doors and windows where sirens are NOT desired. Usually assigned to a zone containing an Emergency button (audible emergency). Interior with Delay Provides entry delay (using the programmed entry time), if tripped when the controller is armed in the Away mode. Bypassed when the controller is armed in the Stay or Stay Instant mode. 24-hour Carbon Monoxide Monitor Trouble Fire No Verification Can be assigned to any wireless zone with a carbon monoxide detector. This zone type is always active and cannot be bypassed. Used with Other response type. Can be assigned to any wireless zone used as a fire zone. This zone type is always active and cannot be bypassed. Characteristics None Entry delay #1 is programmable. Exit delay is independently programmable. Exit and entry delays when armed in Away, Stay or Night Stay mode. Entry delay #2 is programmable. No entry delay when armed in Stay or Away Instant modes. Exit delay regardless of the arming mode selected. Exit delay is independently programmable. Secondary entry delay, if armed in the Away or Stay mode. No entry delay when armed in the Stay Instant or Away Instant mode. Exit delay begins regardless of the arming mode selected. Instant alarm, when armed in Away, Stay, Stay No Delay, Night Stay or Away Instant mode. Delayed alarm (using the programmed entry/exit time) if entry/exit or interior-with-delay zone is faulted first. Instant alarm in all other situations. Active when armed in Away or Away Instant mode. Bypassed automatically when armed in Stay, Night Stay or Stay Instant mode. Instant alarm, when armed in Away, Stay, Night Stay , Stay Instant, or Away Instant (night) mode. Provides a latched trouble sounding from the keypad and, if desired, a Central Station report when disarmed (day). Sends a report to the Central Station but provides no keypad display or sounding. In disarmed state sends a report to the Central Station displays "Not Ready to Arm" on the keypad and Away, Stay and Tools buttons are disabled. Follows sounder timeout Sends a report to the Central Station, and provides alarm sounds at the keypad. Sends a report to the Central Station and provides an alarm sound at the keypad. (There is no keypad timeout.) Instant alarm, with No audible indication when armed in the Away, Stay, Stay No Delay, Night Stay, or Away Instant mode. Follows sounder timeout. Report sent to the Central Station. Provides alarm sounds at the keypad. No reports to the Central Station. Entry delay #1 (with programmed entry time) when armed in the Away mode. Entry delay begins whenever sensors in this zone are violated, regardless of whether an entry/exit delay zone was tripped first. No entry delay when armed in the Away Instant mode. Exit delay regardless of the arming mode selected. Local keypad and detector will sound when this zone type is alarmed. (Pulse Temporal 4). The system will provide a trouble sounding from the keypad
(and a Central Station report, if desired). Alarm sound will pulse (Temporal Fire) when this zone type is alarmed.
- 19 -
Lyric Gateway Installation and Reference Guide Zone Response Type Definitions (Continued) Type Fire with Verification Function Can be assigned to any wireless zone used as a fire zone. Fire with verification is available with smoke detector device type. It cannot be used with heat detectors, combination heat/smoke detectors or fire pull stations. This zone type is always active and cannot be bypassed. Special-purpose zone type used with 5800 and SiX Series wireless keys. Special-purpose zone type used with 5800 and SiX Series wireless keys. Special-purpose zone type used with 5800 and SiX Series wireless keys. Assigned when no-alarm response is required. No reports to the Central Station. activated. Disarms the system when the zone is activated. ArmStay ArmAway Disarm No Alarm Response Monitor Characteristics Alarm sound will pulse (Temporal Fire) when this zone type is alarmed and the alarm has been verified. System verifies alarm by delaying reporting and alarm sounding for 30 seconds after alarm is detected. If the zone remains faulted after 30 seconds a fire alarm is provided. If any other fire zone is faulted during the 30 second delay window a fire alarm is immediately provided for that zone. An alarm for original fire zone will also be provided, if that zone is still faulted. If there are no fire alarms after the 30 second delay expires, the system will open a 60 second window. If any fire zone is faulted during that window a fire alarm will immediately be provided for that zone. Exit delay regardless of the arming mode selected. System is armed in the Stay mode when the zone is activated. System is armed in the Away mode when the zone is No keypad sounding or chime and no display on screen. System can still be armed. Reports to the Central Station, if enabled. Fault/restore events are logged by the system. Activity Zone No. and Zone Descriptor displayed on LCD. Restore will be stored in event log. No keypad sounding or chime. System can still be armed. No reports to the Central Station. Fault/restore events are logged by the system. Monitors entry into a monitored area. Activates a one-time announcement when faulted. Activity Zone No. and Zone Descriptor displayed on LCD. No reports to the Central Station. Fault/restore events are logged by the system. Monitors entry into a monitored area. Activates a zone announcement when faulted. Activity Zone No. and Zone Descriptor displayed on LCD. System re-triggers audible sounding every ten seconds until acknowledged. No reports to the Central Station. Monitors entry into a monitored area. Activates a zone announcement when faulted. Activity Zone No. and Zone Descriptor displayed on LCD. Fault/Restore events are not logged by the system. No reports to the Central Station. Monitors entry into a monitored area. Activates a zone announcement when faulted. Activity Zone No. and Zone Descriptor displayed on LCD. System re-triggers audible sounding every ten seconds until acknowledged (Off sequence or wireless key). Fault/Restore events are not logged by the system. Associated With Entry Delay #2 Programmed Time. Exit delays when armed in Away, Stay or Night Stay mode. No Entry Delay when armed in Away or Stay Instant modes. System can be armed with zone in the faulted state. When the zone is closed it will automatically be inclusive within protection points. If the point is subsequently violated, it will initiate an alarm. Can be assigned to any wireless zone used for automatic Garage Door Open/Close status. Will not initiate an alarm condition on the controller. When zone is in the open state will display FAULT. Does not report alarms to Central Station. Zone will chime if enabled. System can be armed if this zone type is in fault. Can be assigned to any wireless zone used for asset protection. Works as a dynamic monitor of a zone fault/trouble (not alarm). General Monitor General Response Assigned sensors or contacts on doors and windows or asset protection within the premises. Used to track activity of the occupant and alert occupant of the activity of others. Assigned sensors or contacts on doors and windows or asset protection within the premises. Used to track activity of the occupant and alert occupant of the activity of others. Resident Monitor Used to monitor a resident in an area deemed to be dangerous by a caregiver. Resident Response Used to monitor a resident in an area deemed to be dangerous by a caregiver. Requires acknowledgement by caregiver. Garage
(Burglary) Assigned to Automatic Garage Door applications. Provides a status of the garage door close/open real time state. Garage Monitor Assigned to Automatic Garage Door applications. Provides a status of the garage door close/open real time state.
- 20 -
Lyric Controller Installation and Reference Guide System Operation Key/Touchscreen Operation Touchscreen icons displayed on the Smart Device allow the user to arm and disarm the system, and perform other system functions, such as bypassing zones. Zone and system conditions (alarm, trouble, bypass) are displayed on the LCD. When an alarm occurs, the Gateway and Smart Device (if installed) will sound, and the zone(s) in alarm will be displayed. Pressing any key will silence the keypad sounder for 10 seconds (only once). Disarming the system will silence both console and external sounders. When the system is disarmed, any zones that were in an alarm condition during the armed period will be displayed (memory of alarm). To clear this display, simply repeat the disarm sequence by selecting Disarmed and entering the Security Code. The console also features chime annunciation, and three panic key icons for silent, audible, Fire or Medical emergency alarms. These keys can notify the Central Station of an alarm condition, if that service is connected. Panic Key/Icons There are three panic keys that are active (if programmed) when the Emergency or any of the keys is selected for approximately five seconds. The panic key screen will timeout if a selection is not made within ten seconds. The keys can be used to manually initiate alarms and send a report to the Central Station. Each can be individually programmed for 24-hour silent, audible, personal or fire emergency responses. The panic function is activated when the respective keys is pressed. The panic functions are identified by the system as follows:
Zone 995 996 998 999 Function Fire Emergency Medical Emergency Local Alarm Police Emergency Important: For the silent panic functions to be of practical value, the system must be connected to a Central Station. Security Codes Installer Code The installer programs the 4-digit Installer Code initially as part of the programming procedure. The factory default Installer Code is 4-1-1-2, but may be changed in the Installer Code programming field. The Installer Code is the only code that allows entry into Installer Programming mode. Master Code In normal operation mode, the Master (Security) Code is used to enter the 4-digit User Security Codes and enter the Master User Tools Menu mode. Enter/Change the Master Code by Installer. The factory default Master Code for the Lyric Gateway is set to 1-2-3-4. The Master Code is used to enter the 4-
digit User Security Codes. SCREEN ACTION 1. After entering the Master User Menu screen, select the Users icon. The system displays the User Code Programming screen. 2. Select Master, then select Edit. 3. Enter a new 4-digit Master (Security) Code on the displayed keypad. The system displays the new code on the left side of the screen. 4. Select Done when you are finished. 5. The system returns to the Master Code Programming screen. Secondary User Codes In normal operation mode, the Master (Security) Code can be used to assign up to 46 secondary 4-digit security codes, including a Guest Code and a Duress Code. The Master Code can also be used to individually remove secondary codes from the system. Refer to the Lyric Gateway User Manual for additional information.
- 21 -
Lyric Gateway Installation and Reference Guide Reset Master Code 1. After Entering the Programming Mode, select Users from the Master User screen menu. 2. Select Master followed by Edits to reset the Master User Code. 3. Select User Code. 4. Enter a new Master Code on the displayed keypad, then select Done. The system returns to the previous screen. System Operation 5. Select Save 6. If confirmed, the Master Code will be reset back to 1-2-3-4. This will be logged in the System Event Log as User: 1 Reset Master Code, E655. The system returns to the second page of the Installer Programming Tools menu. OR If the reset failed, the system will display: Command Failed. Unable to Reset Master Code. This will only occur if the code 1-2-3-4 has been assigned to another User in the panel. Security Code Notes The Master and Secondary security codes permit access to the system for arming, disarming, etc. The Installer Code can disarm the system only if it was used to arm it. In addition, the Installer Code cannot disarm the system if it was armed by pressing and holding a Quick-Arm button. The Guest Code can disarm the system only if it was used to arm it. In addition, the Guest Code cannot disarm the system if it was armed by pressing and holding a Quick-Arm button. Duress code sends a special code to the Central Station when used to perform any system operation. Instruct users to be careful not to use this code for normal usage. Opening/closing reports are sent for the Installer Code, with the appropriate subscriber number. Master Code and secondary user codes are sent as User No. 2 and 3-48 respectively, in Contact ID format (with the appropriate user number). Important Security Notice Please inform the User about the security importance of their wireless key (key fob), and what to do if it is lost. Explain that the wireless key is similar to their keys or access card. If lost or stolen, another person can compromise their security system. They should immediately notify the Dealer/Installer of a lost or stolen wireless key. The Dealer/Installer will then remove the wireless key programming from the security system.
- 22 -
System Operation System Displays The following icons will be displayed on the Home screen along with specific zone status information (if applicable) to indicate system status. Lyric Controller Installation and Reference Guide DISPLAY DEFINITION Temperature Other Automation Icon
(Z-Wave Node Failure OR Z-
Wave Controller Not Ready) Garage Door Open WiFi source present and signal strength No WiFi source DISPLAY DEFINITION AC Loss Alarm
(Intrusion) Ready To Arm Armed Away Armed Stay Armed Night Stay Armed Custom Restart Timer Battery Low Bypassed Zones CO Alarm Reporter Failure Low Batt 850 Keypad 900 Cover Tamper DISPLAY DEFINITION 901 Expansion Module Tamper 950 Comm. Trouble 988 RF Jam
(5800 Series Wireless Device) 990 RF Jam
(SiX Series Wireless Device) 998 Local Alarm Door Open Window Open Fire OR Heat Sensor Environmental Flood Glass Break Medical Alarm Keypad Motion Zone Status Displays The icons associated with the programmed zones are displayed on the Zones screen. The icons color indicates the zone status (i.e.; yellow icon indicates the zone is faulted and a red icon indicate the zone is in alarm). In addition a bypass icon is displayed alongside the icon for a bypassed zone.
- 23 -
Lyric Gateway Installation and Reference Guide System Operation (Continued) ETL Audio alarm verification has not been evaluated by ETL. Audio Alarm Verification (Two-Way Voice Feature) This feature allows the Central Station operator to listen, talk to or conduct a two-way conversation with an individual(s) at the premises. It also assists the operator in gathering information about the nature and location of the alarm that may be helpful in responding to police and fire departments. All Lyric Controllers are capable of supporting the Two-Way Voice feature. The Lyric Gateway does not make system announcements when the Two-Way Voice feature is active. If a WiFi connection is being used for Two-Way Voice (AAV), sufficient bandwidth must be available. AAV requires a continuous WiFi upload/download bandwidth of 90kbps for proper operation. WiFi bandwidth less than 90kbps may result in degraded performance. Activation Fire and CO alarms will prevent the Lyric Gateway from starting an AAV session. A new Fire or CO alarm will end an AAV session that is in progress. The controller sends the alarm message followed by a Listen-in-to-Follow message (Contact ID code 606) to the Central Station. The Listen-in-to-Follow message causes the Central Stations digital receiver to temporarily hold the phone line for approximately 1 minute. When the controller receives the kissoff from the Central Station, indicating that the alarm message has been received, the Two-Way Voice (AAV) feature is activated in the (default) Listen Mode and sirens and keypad sounds are discontinued. The controller transmits a beep acknowledgment to the Central Station, once per second. The beep alternates between two tones and indicates that the controller is waiting for a session command from the Central Station operator. Once a command is issued the beep acknowledgement is discontinued, however, if a command is not issued within two minutes the system will time out and the call will be terminated. Operator Commands The Central Station operator begins the session, which last 5 minutes, by entering one of the valid AAV commands shown in the table below. The session may be extended 5 minutes, without changing the operating mode, by pressing the [7] key on the touch-tone phone. Selecting another operating mode also resets the session an additional 5 minutes. During the last minute of the 5 minute, session, the controller generates two beeps every 30 seconds to alert the Central Station operator that the session is about to time out. The Central Station operator may then extend the session by pressing the [7] key on the touch-tone phone. If the session is not extended, the phone line is disconnected and the session is ended. Sessions may be ended at any time by pressing the [9] key on the touch-tone phone. The AAV modes are described as follows:
Note: When entering AAV commands make sure the Central Station receiver has been disconnected from the phone line, otherwise AAV commands may not go through. Key 1 2 3 7 9 Function Talk Mode: Pressing the [1] key on the touch tone phone, enables one-way voice communication from the Central Sation to the violated premises, and allows the operator to communicate through the controllers built-in speaker. In this mode the controllers Panic and Home buttons blink alternately. VOX (Voice) Mode: Pressing the [2] key on the touch-tone phone, enables two-way voice communications between the Central Station and the violated premises via the controllers built-in speaker and microphone. In this mode the controllers Panic button is lit Red and the Home button is alternately lit Red and Green. Listen Mode: Pressing the [3] key on the touch-tone phone, Enables one-way audio from the violated premises to the Central Station. The Listen Mode is the start up default mode of the voice feature and allows the operator to listen through the controller microphone. This mode does not affect the existing LED pattern. Extends the session 5 minutes without changing its operating mode. Ends the session and disconnects the phone line.
- 24 -
Lyric Controller Installation and Reference Guide System Operation Event Log The Lyric Gateway Series event log is capable of recording and displaying up to 6,000 system events. These events are stored locally in the Gateway, in chronological order, and transmitted to the Central Station. When the maximum number of events is reached in the Event Log, the system will overwrite the oldest event first. The type of events that can be recorded is selectable and is programmed in the System Type programming field. The event log can be reviewed by entering the Installer Programming or Master User Programming mode and selecting Events. Refer to the Lyric Gateway User Manual for additional information. The Events and CID Codes displayed vary according to the options that are programmed. The tables below provide definitions of the events/codes that may be transmitted to the Central Station and/or displayed by the controller. Note: In the unlikely condition that the backup battery becomes fully discharged when AC power is lost, any system activity performed after the low battery notification will not be saved in the event log. Additionally, the controller will revert to the status condition as before the low battery notification. Contact ID Event Log Codes CID Code 110 121 122 123 131 132 134 135 137 145 146 150 162 301 302 305 308 316 341 344 350 353 354 373 374 380 381 383 384 401 403 406 407 408 441 455 459 461 570 601 602 606 607 623 627 628 654 655 Definition Alarm, Fire Alarm, Duress Alarm, Silent Alarm, Audible Alarm, Perimeter Alarm, Interior Alarm, Entry/Exit Alarm, Day/Night Alarm, Tamper Expansion Module Tamper Silent Burglary 24-Hour Non-Burglary Carbon Monoxide Detected Trouble, AC Loss Trouble, Low System Battery Trouble, System Reset System shutdown System Tamper*
Trouble, Case Tamper Trouble, RF Receiver Jam Detect Long Range Radio Reset Trouble, Long Range Radio Transmitter Fault Failure to Communicate Event Trouble, Fire Trouble Trouble, Exit Error Alarm Trouble, Sensor Trouble, Loss of Supervision RF Trouble, Sensor Tamper RF Low Battery Open/Close by User Open/Close Automatic Cancel Remote Arm/Disarm Quick Arm Armed Stay Auto-Arm Failed Recent Close Wrong Code Entry Zone/Sensor Bypass Manual Trigger Test Report Periodic Test Report Listen-in to follow Walk Test Event 90% Full Program Mode Entry Program Mode Exit System Inactivity Reset Master Code Event Log Display Fire Duress Silent Audible Perimeter Interior Entry/Exit Day Night Tamper Expansion Module Tamper Silent Burglary 24 Hour Non-Burglary Carbon Monoxide Detected AC Loss Low system battery System Reset System shutdown System Tamper Cover Tamper RF Jam Detect Long Range Radio Reset Comm. Trouble Failure to Communicate Event Fire trouble Exit error alarm Sensor trouble Superv Loss-RF Sensor Tamper RF Low Battery Arm Away/Disarmed Automatic O/C (or Scheduled Arming) Cancel Remote Arm/Disarm Quick arm Arm Stay/Disarmed Auto-arm Failed Recent Closing Wrong Code Entry Zone Bypass Manual Trigger Test Report Periodic test report Listen-in to follow Walk Test Mode Event Log 90% Full Program mode entry Program mode exit System Inactivity User Code
*If APL is enabled, AlarmNet 360TM will generate a special comm. fail message (E316) if it does not hear from a unit within 15 minutes after a delayed alarm is delivered. This message is meant to alert the Central Station that the system has been tampered with and may have been compromised.
- 25 -
Lyric Gateway Installation and Reference Guide Contact ID Event Log Codes System Operation CID Code 759 760 761 762 1401 3000 3001 3100 3101 3200 3201 3300 3301 3302 3400 3401 3402 3403 3404 3405 3406 3407 3408 3409 3410 3411 3412 3500 3501 4000 4001 4002 4003 5000 Definition Resident Monitor Zone Response Resident Response Zone Response General Monitor Zone Response General Response Zone Response Local Alarm Binary Switch Off Binary Switch On Multi Level Switch Change Level (Off) Multi Level Switch Change Level (On) Garage Door Close Garage Door Open Door Lock Unlocked Door Lock Locked Door Lock Jammed Thermostat Mode Off Thermostat Mode Heat Thermostat Mode Cool Thermostat Mode Auto Thermostat Mode Aux /Em Heat Thermostat Fan Mode Auto Thermostat Fan Mode Manual On Thermostat Fan Mode Circulate Thermostat Set Heat Point Thermostat Set Cool Point Thermostat Hold Thermostat No Scheduling Thermostat Normal Mode Low Battery Low Battery Restore Voice Command Success Voice Command Failed Voice Trigger Success Voice Trigger Fail Critical Panel Firmware Update Downloaded Event Log Display Resident Monitor Zone Response Resident Response Zone Response General Monitor Zone Response General Response Zone Response Local Alarm Switch Off (Z-Wave Device) Switch On (Z-Wave Device) Multilevel Switch Off (Z-Wave Device) Multilevel Switch On (Z-Wave Device) Garage Door Close Garage Door Open Door Unlocked (Z-Wave Device) Door Locked (Z-Wave Device) Door Lock Jammed (Z-Wave Device) Thermostat Mode Off Thermostat Mode Heat Thermostat Mode Cool Thermostat Mode Auto Thermostat Mode Aux /Em Heat Thermostat Fan Mode Auto Thermostat Fan Mode Manual On Thermostat Fan Mode Circulate Thermostat Set Heat Point (and temperature) Thermostat Set Cool Point (and temperature) Thermostat Hold Thermostat No Scheduling Thermostat Normal Mode Low Battery (Z-Wave Device) Low Battery Restore (Z-Wave Device) Displays Variable Voice Command Text Displays Variable Voice Command Text Displays Variable Voice Trigger Text Displays Variable Voice Trigger Text Critical Panel Update Downloaded Central Station Messages The following messages are sent by the controller internal cellular or WiFi devices for the conditions listed below. Restore Code R350C0951 R350C0952 Alarm Condition Power On / Reset Primary Communication Path Supervision Secondary Communication Path Supervision Test Alarm Code E33900950 E350C0951 E350C0952 555555559
- 26 -
Lyric Controller Installation and Reference Guide Testing the System TO THE INSTALLER Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system. The installer should assume the responsibility of developing and offering a regular maintenance program to the user as well as acquainting the user with the proper operation and limitations of the alarm system and its component parts. Recommendations must be included for a specific program of frequent testing (at least weekly) to ensure the systems proper operation at all times. Test Modes The following tests are available to the Installer or User via the Advanced programming option:
Option System Information Walk Test Comm. Test System Information is displayed. Select OK to return to the previous screen. Function The Walk Test mode allows each protection point to be checked for proper operation. Refer to the User Manual for additional information. The following tests are available to the Installer via the Gateway keypad. RF Sniffer Test Go-No-Go Test Diagnostics Used to verify the RF transmitters have been properly installed. Used to verify adequate RF signal strength from proposed transmitter locations. Provides access to the Reboot Feature. Refer to the paragraph in this section for additional information regarding this feature. Provides access to the Zone Discovery mode. Refer to the paragraph in this section for additional information regarding the Zone Discovery feature. Zone Discovery Testing the System After installation is completed, the security system should be carefully tested, as follows:
Step Action 1. With the system in the disarmed state, check that all zones are intact. If the Status Shield is not lit green, select the Security icon on the Smart Device followed by the Zones icon to display the faulted zone(s). If necessary, restore faulted zone(s) so that the Home button lights. Fault and restore every sensor individually to assure that it is being monitored by the system. Armed System Test (via AlarmNet 360) Alarm messages will be sent to the Central Station during the following steps 1 and 2. Notify the Central Station in advance that tests will be in progress. Step 1. 2. 3. 4. Action Arm the system and fault one or more zones. Silence alarm sounder(s) and disarm the system by selecting Disarmed and entering the Security Code. Check entry/exit delay zones. Check the keypad-initiated alarms that are in the system by selecting Emergency followed by applicable Panic keys. If the system has been programmed for audible emergency, the keypad will emit a steady alarm sound, and Alert will flash red. In addition, ALARM and zone number will be displayed on Smart Device. Silence the alarm by selecting Disarmed and entering the Security Code. If the system has been programmed for silent emergency, there will be no audible alarms or displays, but a report will be sent to the Central Station. Notify the Central Station when all tests are finished, and verify results with them. To test the wireless part of the system and the RF receiver, perform the RF Sniffer Mode and Go-No-
Go Tests. NOTE: System Test mode and Go/No Go Test will be automatically terminated after 3-1/2 to 4 hours if the installer or user does not manually terminate it. This ensures that fire and panic zones will not remain disabled. However, Sniffer mode does not automatically expire. You must manually exit Sniffer mode by selecting the Home key and entering the Master Code, to return to normal operation. During the final 5 minutes the system will emit double beeps indicating that the end of Test mode is nearing.
- 27 -
Lyric Gateway Installation and Reference Guide Testing the System (Continued) RF Sniffer Test Mode This mode is used to verify that all transmitters have been properly programmed. Sniffer Mode does not automatically expire. You must manually exit Sniffer Mode to return to normal operation. Go-No-Go Test Mode Conducting this test with your hand wrapped around the transmitter will cause inaccurate results. If a button is pressed on a transmitter that has been programmed to set ARM AWAY, ARM STAY, or DISARM, the system will exit the Go/No Go Test mode and the programmed action will occur. The Go-No-Go tests is used to verify adequate RF signal strength from the proposed transmitter location, and allow you to reorient or relocate transmitters if necessary, before mounting the transmitters permanently. This mode is similar to the RF Sniffer Mode, except that the wireless receiver gain is reduced. This will enable you to make sure that the RF signal from each transmitter is received with sufficient signal amplitude when the system is in the normal operating mode. During Go/No-Go mode the system beeps every 30-40 seconds. Enter Go/No-Go Test mode 1. Enter Installer Code (4112) + 11 + 51 (on the Gateway keypad). Exit Go/No-Go Test mode 1. Select Disarmed+ Enter Installer Code (4112). Zone Discovery Mode Zone Discovery mode requires Installer supervision when in use. The system is not fully operational for fire or life safety while Zone Discovery Mode is active. Zone discovery mode can be used to remotely view all zones that have been programmed in the system for operation. The zones must have a response type programmed and in the case of RF zones, must also have a serial number programmed. All zones programmed (except for duress) will be displayed. Enter Zone Discovery 1. With the System in the Installer Programming mode, select the Test button and then select the Zone Discovery button. The Zone Discovery button will be highlighted indicating that the mode is active. Exit Zone Discovery 1. Select the Home key and enter the Master Code. If you do not exit Zone Discovery mode manually, the system will automatically exit zone discovery mode in approximately 1-4 minutes dependent upon the number of zones that are programmed. The system beeps once and returns to the home screen. Rebooting the System The Reboot function allows you to restart the system if required. To reboot the system perform the following:
Step 1. 2. 3. 4. Action Select the Security icon followed by the Tools icon. Enter the Master User code (1234) and select the Advanced icon. Select the Reboot button. A confirmation screen appears. Select Yes to reboot the Gateway. NOTE: After the reboot sequence is complete it is recommended that you perform a Walk Test to verify that all transmitters are operational in the system.
- 28 -
Lyric Controller Installation and Reference Guide Programming Default Values Programming Field Options System Alarm Report Delay Burglary Alarm Sound Daylight Savings Time Time Zone Offset Software Version Temperature Unit Installer Language Two-way Voice Local Programming Lockout Z-Wave Support Display alarm Cancel Lack of Usage Notify RF Jam Number of Reports (Swinger Shutdown) First Test Report Offset Report Frequency System Reporter Panel Sync Delay Time Z-Wave Door Lock Area Area Number Entry Delay 1 Entry Delay 2 Exit Delay Burglary Bell Timeout Fire Bell Timeout Quick Arm Quick Exit Restart Exit Time Chime Mode Force Bypass Exit Warning Display Exit Time Power-Up In Previous Auto Stay Arming Arm Confirm Communicator City ID CS ID Sub ID Supervision High Usage Plan Old Alarm Time IP Fault Time Communications Path (Inter. Dev.) No delay, 15 Seconds, 30 Seconds, 45 Seconds Yes, No Yes, No XX.XX.XXXXX.XXX Fahrenheit, Celsius English, Spanish, French, Portuguese Not programmable Yes, No Yes, No Yes, No Disabled, 1 Day, 7 Days, 27 Days, 90 Days, 180 Days, 365 Days Disabled, RF Jam Log, RF Jam Log and Report 1, 2, 3, 4, 5, 6 6 Hours, 12 Hours, 18 Hours, 24 Hours Never, Every Day, Every 7 Days, Every 30 Days Not programmable Not programmable 0 Minutes - 120 Minutes Disabled, Arm Stay, Arm Away, Arm Without Autostay 1 None, 15 Seconds, 30 Seconds, 45 Seconds, 60 Seconds, 90 Seconds, 2 Minutes, 3 Minutes, 4 Minutes None, 15 Seconds, 30 Seconds, 45 Seconds, 60 Seconds, 90 Seconds, 2 Minutes, 3 Minutes, 4 Minutes 45 Seconds,60 Seconds, 90 Seconds, 120 Seconds No, 4 Minutes, 8 Minutes,12 12 Minutes, 16 Minutes, No, 4 Minutes, 8 Minutes,12 12 Minutes, 16 Minutes, Yes, No Yes, No Yes, No Yes, No Yes, No Not programmable Yes, No Not programmable Yes, No All RF, None, RF Keyfob, RF Keypad 01-99 01-FE 0001-9999 None, 24 Hours, 30 Days Yes, No 10 Minutes, 15 Minutes, 30 Minutes, 1 Hour, 2 Hours, 4 Hours, 8, Hours, 12 Hours, 24 Hours 1 99 Minutes Cellular, WiFi - IP
- 29 -
Programmed Default 30 Seconds Yes Yes
(UTC-5:00 Eastern Time (US & Canada) XX.XX.XXXXX.XXX Fahrenheit English No No Yes Yes Disabled RF Jam Log 2 6 Hours Never Yes Yes 3 Minutes Disabled 1 30 Seconds 30 Seconds 60 Seconds 4 Minutes 4 Minutes Yes Yes Yes Yes No Yes Yes Yes Yes None Blank Blank Blank 30 days No 10 Minutes 60 Minutes WiFi - IP Lyric Gateway Installation and Reference Guide Programming Default Values Programming Field Options Programmed Default 255.255.255.255 255.255.255.255 255.255.255.255 255.255.255.255 60 Minutes Yes No Yes Yes, No Up to 12 digits Up to 12 digits Up to 12 digits Up to 12 digits 1 99 Minutes Use DHCP NIC IP Address Subnet Mask Gateway IP Address DNS Server IP Address Cellular Fault Time Cellular 24 Hr Test/UL864 Comm. Fire Yes, No Cellular Rollover Yes, No Reporter Arm Away Arm Stay Disarm Exit Error Alarm Restore Alarm Cancel Test Test Restore Low Battery Low Battery Restore RF Low Battery RF Low Battery Restore Recent Closing Event Log Full Trouble Trouble Restore Bypass Bypass Restore AC Loss AC Loss Restore Log All Events Log Alarm Events Log Open/Close Events Log Trouble Events Log Non Security Events Log Bypass Events Zone Programming The defaults are shown. Refer to the Programming Field Explanations for additional information. Zones 1-64 are RF Zones, RF Zones 65-69 are Garage Door Zones. (Refer to SENSORS in AlarmNet 360) Zones 131-162 are Keyfob Zones (Refer to KEYFOBS in AlarmNet 360) Zones 280-291 are Temperature Zones (Refer to SENSORS in AlarmNet 360) Zones 850-857 are Keypad Zones (Refer to KEYPADS in AlarmNet 360) Zones 995, 996, 998 and 999 are Panic Zones (Refer to SENSORS in AlarmNet 360) Yes, No Yes, No Yes, No Not programmable Yes, No Yes, No Not programmable Not programmable Yes, No Yes, No Yes, No Yes, No Not programmable Yes, No Yes, No Yes, No Yes, No Yes, No Yes, No Yes, No Yes, No Yes, No Yes, No Yes, No Yes, No Yes, No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
- 30 -
Programming Default Values (Continued) Lyric Controller Installation and Reference Guide For Zone Programming Options refer to Explanation of Zone Assignment Table Headings Chime Supervision Response Type Entry Exit 1 Entry Exit 1 Perimeter Perimeter Perimeter Perimeter Standard Standard Standard Standard Standard Standard Disabled Disabled See Programming Field Explanations Interior with Delay Fire No Verification Alarm Report Yes Yes Yes Yes Yes Yes Yes Yes Zone No. 1 2 3 4 5 6 7 8 9-64 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 163 280 281 282 283 284 285 286 287 288 289 290 291 850 851 852 853 854 855 856 857 995 996 998 999 Loop No. 2 2 2 2 2 2 1 8 Device Type Door Door Window Window Window Window Motion Sensor Smoke Detector 3 2 4 1 3 2 4 1 3 2 4 1 3 2 4 1 3 2 4 1 3 2 4 1 3 2 4 1 3 2 4 1 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Key Fob Temperature Temperature Temperature Temperature Temperature Temperature Temperature Temperature Temperature Temperature Temperature Temperature SiX Keypad SiX Keypad SiX Keypad SiX Keypad SiX Keypad SiX Keypad SiX Keypad SiX Keypad Fire Medical Local Alarm Police Supervised Supervised Supervised Supervised Supervised Supervised Supervised Supervised Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button Button High Temp Low Temp High Temp Low Temp High Temp Low Temp High Temp Low Temp High Temp Low Temp High Temp Low Temp 60Min 60Min 60Min 60Min 60Min 60Min 60Min 60Min Arm Night N/A N/A N/A N/A N/A N/A No N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Zone Descriptor Front Back Arm Away Disarm No Response No Response Arm Away Disarm No Response No Response Arm Away Disarm No Response No Response Arm Away Disarm No Response No Response Arm Away Disarm No Response No Response Arm Away Disarm No Response No Response Arm Away Disarm No Response No Response Arm Away Disarm No Response No Response Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor N/A N/A N/A N/A N/A N/A N/A N/A Fire No Verification 24 Hour Auxiliary Local Alarm 24 Hour Silent Yes Yes No No Yes Yes No No Yes Yes No No Yes Yes No No Yes Yes No No Yes Yes No No Yes Yes No No Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes N/A N/A N/A N/A N/A N/A N/A N/A Yes Yes Yes Yes Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled N/A N/A N/A N/A N/A N/A N/A N/A
- 31 -
Disabled Disabled Disabled Disabled Panic Trigger Panic Trigger Panic Trigger Panic Trigger Lyric Gateway Installation and Reference Guide Programming Default Values (Continued) Explanation of Zone Assignment Table Headings Loop Number - Used with 5800 Devices. Entries are 1-4, depending on device being used. Refer to the transmitters instructions or the figure provided for appropriate loop numbers. Device Type- Dependent upon the Zone Number being programmed. Response Type - Dependent upon the Device Type that has been selected. Alarm Report Activate/Deactivate reporting option for the device. Options: Yes, No Chime Enable/Disable chime sounding for the device (applies to Entry/Exit, Perimeter and Interior Response Types only). Disabled Standard Melody Melody Long Ascend Ascend Long Doorbell 2 Evolve Alert 1 Alert 2 Doorbell 1 Supervision - Dependent upon the Zone Number being programmed. Wireless Zone
(Zone 1-69) Supervised Unsupervised Temperature Zone
(Zone 280-291) High Temp Low Temp Key Zone
(Zone 131-162) Button Arm Night Activate/Deactivate specific Motion Sensors at (applies to Motion Sensor Response Type only). Options: Yes, No Zone Description1/2 Enter Zone Descriptors on displayed keypad. System Announces pre-programmed voice descriptors. Device/Response Type Matrix e p y T e s n o p s e R 1 t i x E y r t n E 2 t i x E y r t n E r e t e m i r e P e s n o p s e R t n e d i s e R r o t i n o M t n e d i s e R e s n o p s e R l a r e n e G r o t i n o M l a r e n e G r e w o l l o F r o i r e t n I i t h g N
/
y a D l y a e D h t i W r o i r e t n I n o i t a c i f i r e V h t i W e r i F n o i t a c i f i r e V o N e r i F y r a i l i x u A r u o H 4 2 l i e b d u A r u o H 4 2 t n e l i S r u o H 4 2 d e s U t o N y a t S m r A r o t i n o M y a w A m r A m r a s i D l y r a g r u B t n e l i S e s n o p s e R o N i e d x o n o M n o b r a C x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x m r a A l l a c o L e g a r a G r o t i n o M e g a r a G x x l e b u o r T Device Type Carbon Monoxide Detector Door Environmental Fire Flood Garage Door Glass Break Heat Sensor Medical Motion Sensor Other Police Smoke Detector Temperature Window
- 32 -
Lyric Controller Installation and Reference Guide Zone Response Type Matrix SiX Series Device Signal Strength Signal strength for the enrolled SiX Series Devices is displayed on the Zone Programming Screen for the individual Zone that is programmed. Signal strength information is provided below. Icon Description Four Green Bars Three Green Bars Two Green Bars One Green Bar Four Red Bars Signal Strength Suprieure -27 dBm Suprieure -45 dBm Suprieure -63 dBm Suprieure -81 dBm Infrieure -81 dBm (en dessous du seuil)
- 33 -
Lyric Gateway Installation and Reference Guide Regulatory Agency Statements Federal Communications Commission (FCC) Part 15 The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC IC Statement This device complies with Part 15 of FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reue y compris les interferences causant une reception indsirable. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 in (20 cm) from all persons and must not be co-located or operated in conjunction with any other transmitter except in accordance with FCC multi-transmitter product procedures. RF Exposure Warning Exposition aux Frequences Radio: L'antenne (s) utilise pour cet metteur doit tre installe une distance de sparation d'au moins 7,8 pouces (20 cm) de toutes les personnes. Mise en Garde IMPORTANT NOTES ABOUT EXTERNAL ANTENNAS If an external cellular radio antenna is used, the antenna may be installed or replaced ONLY by a professional installer. TO THE INSTALLER For the Lyric-3G, the external antenna must not exceed a maximum directional gain (including cable loss) of 3.2 dBi at 850 MHz and 2.3 dBi at 1900 MHz. For the Lyric-CDMA, the external antenna must not exceed a maximum directional gain (including cable loss) of 8.5 dBi at 850 MHz and 4.1 dBi at 1900 MHz.
- 34 -
Lyric Controller Installation and Reference Guide THE LIMITATIONS OF THIS ALARM SYSTEM WARNING While this System is an advanced design security system, it does not offer guaranteed protection against burglary, fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:
Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Finally, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending on the nature of the fire and/or location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death. Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of the protected area approaches the temperature range of 90 to 105F (32 to 40C), the detection performance can decrease. Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices are located on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-
impaired people. Communication paths needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Communication paths are also subject to compromise by sophisticated intruders. Even if the system responds to the emergency as intended, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. The security keypad (and remote keypad) should be tested as well. Wireless transmitters are designed to provide long battery life under normal operating conditions. Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce the actual battery life in a given installation. This wireless system, however, can identify a true low battery situation, thus allowing time to arrange a change of battery to maintain protection for that given point within the system. Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.
- 35 -
Lyric Gateway Installation and Reference Guide Agency Notices 1. For Residential Burglar Alarm installations with line security, total exit delay time must not exceed 60 seconds. For Burglar Alarm installations without line security, total exit delay time must not exceed 120 seconds. 2. Periodic testing must be at least every 24 hours. 3. Remote downloading without an alarm company technician on-site (unattended downloading) is not permissible for ETL installations. 4. As SIA limits for delay of alarm reporting and sounding can exceed UL Standard limits for commercial and residential applications, the following requirements per UL681 are provided:
The maximum time that a control unit shall be programmed to delay the transmission of a signal to a remote monitoring location, or to delay the energizing of a local alarm sounding device to permit the alarm system user to enter and disarm the system, or to arm the system and exit shall not exceed:
a) 60 seconds for a system with standard line security or encrypted line security, b) 120 seconds for a system without standard line security or encrypted line security, or c) 120 seconds for a system that does not transmit an alarm signal to a remote monitoring location. SIA Quick Reference Guide Range Shipping Default SIA Requirement Feature Programming Section Installation and Setup Guide or Programming Guide Reporter/
Report Selection Reporter/Options Not selectable Not selectable Enabled or Disabled 1 to 6 Reports Enabled Enabled Enabled 2 Reports Enabled Enabled Enabled 2 Reports Exit Error Recent Closing Alarm Cancel Number of Reports Alarm Report Delay (Abort Window) Entry Delay # 1 Entry Delay # 2 Exit Delay Restart Exit Time Enabled or Disabled Exit Warning Auto Stay Arming Cross Zone Delay 30 seconds and 2 Not selectable Enabled or Disabled 15, 30 and 45 seconds 30 seconds 30 seconds*
None, 15, 30, 45, 60 and 90 seconds and 2, 3 or None, 15, 30, 45, 60 and 90 seconds and 2, 3 or 45, 60, 90 seconds and 2 minutes minutes (in 30 second increments), 3 minutes Zone Type Fire with Verification must be selected for Fire Zone Duress Code is Programmed by Master User as User 48 System tests provided as a User Function 30 seconds 30 seconds 60 Seconds Yes (Enabled) Yes (Enabled) Yes (Enabled) None (Disabled) 30 seconds minimum 30 seconds minimum 45 seconds minimum Enabled Enabled Enabled Enabled and two zones programmed Disabled Disabled Disabled n/a Disabled Disabled n/a Disabled Zones Fire Alarms User Guide User Functions/
User Access Duress System Functions/
Testing the System**
System Test System Settings Communications While the system is in Test mode, no alarm reports are sent to the Central Station
* Combined Entry Delay and Alarm Report Delay (Abort Window) should not exceed 1 minute.
** Refer to the User Guide for procedures on Testing the System.
- 36 -
Lyric Controller Installation and Reference Guide Specifications Lyric Gateway Residential Burglar and Fire Alarm Control Panel Physical:
8.75 (222mm) W x 7 (178mm) H x 1.5 (38mm) D 110VAC, 60 Hz/9 Vdc from plug-in 2.5A power supply Dimensions:
Electrical:
Voltage Input:
Rechargeable Backup Battery: Nickel-metal hydride battery pack rated at 7.2 Vdc Communication:
Formats Supported:
For patent information, see www.honeywell.com/patents ADEMCO Contact ID Reporting, 10 characters/sec SIA/DCS Format, 2225Hz Handshake, Data Tones, 2025/2235Hz, baud
- 37 -
Lyric Gateway Installation and Reference Guide Glossary AES Advanced Encryption Standard APL Advanced Protection Logic dBM decibels milliwatt (power ratio) CDMA - Code Division Multiple Access is a channel access method used by various radio communication technologies that allows many users to occupy the same time and frequency allocations in a given band/space. DHCP Dynamic Host Configuration Protocol, which provides a mechanism for allocating IP addresses dynamically so that addresses can be reused when hosts no longer need them. DNS Domain Name System, which is a distributed hierarchical naming system used to resolve domain names
(e.g., www.yahoo.com) into numerical IP addresses (e.g., 204.17.25.1). Ec/Io Signal to noise ratio of the current channel for CDMA (Measured in dB). Eb/No Signal to noise ratio of the current channel for UTMS (3G) (Measured in dB). ESN Electronic Serial Number (32 bit number that identifies a CDMA device) Gateway IP Address A gateway (sometimes called a router) is a computer and/or software used to connect two or more networks (including incompatible networks) and translates information from one network to the other. The Gateway IP address is the IP address for the gateway. GPRS General Packet Radio Service GSM Global System for Mobile communications, which is an international standard for digital mobile phone systems used for cellular communication. HSDPA High-Speed Downlink Packet Access HSPA High-Speed Packet Access ICCID Integrated Circuit Card Identifier (SIM Card serial number) IMEI International Mobile Equipment Identity number IP Internet Protocol IP Address A unique number consisting of four parts separated by periods, sometimes called a "dotted quad.,"
for example: 204.17.29.11, assigned to every computer/workstation connected to the Internet. IP numbers can be "static" (assigned and unchanging) or "dynamic," assigned via DHCP at each and every startup. ISP Internet Service Provider KBPS Kilobits per second MAC ID Media Access Code; located on the module label. MEID Mobile Equipment Identifier (56 bit number that identifies a CDMA device) NIC Network Interface Card RSCP Received Signal Code Power (Ratio of RSSI and Ec/No) RSSI Received Signal Strength Indication SCID SIM Card ID Subnet Mask A Subnet is a portion of a network that shares a network address with other portions of the network, and is distinguished by a subnet number. The Subnet Mask is a 32-bit address mask used in IP to indicate the bits of an IP address that are being used for the subnet address. UMTS Universal Mobile Telecommunications Service WEP Wired Equivalent Privacy WPA WiFi Protected Access WPS WiFi Protected Setup
- 38 -
Lyric Controller Installation and Reference Guide Contacting Technical Support PLEASE, before you call Technical Support, be sure you:
READ THE INSTRUCTIONS!
Check all wiring connections. Determine that the power supply and/or backup battery are supplying proper voltages. Verify your programming information where applicable. Note the proper model number of this product, and the version level (if known) along with any documentation that came with the product. Note your Honeywell customer number and/or company name. Having this information handy will make it easier for us to serve you quickly and effectively. Technical Support: ...................................................................................................... 1-800-645-7492 (8 a.m.-10 p.m. E.S.T.) MyWebTech: ................................................................................................................... https://www.mywebtech/honeywell.com
- 39 -
Index Lyric Gateway Installation and Reference Guide 24-Hour Silent ............................................................ 22 300-03864-AIO ........................................................... 7 300-03866-AIO ........................................................... 7 300-04063V1 .............................................................. 10 300-04705V1 .............................................................. 10 5800 Series Transmitter Loop Numbers .......... 14 5800 Series Transmitters ....................................... 13 5802MN ......................................................................... 13 5804E ............................................................................ 13 5816 ................................................................................. 13 5834-4 ........................................................................... 13 5878 ................................................................................ 13 AC Power ...................................................................... 10 AC Power Loss ............................................................. 7 ADEMCO Contact ID ............................................... 39 Armed System Test ................................................. 28 Audio Alarm Verification (Two-Way Voice Feature) ................................................................... 25 Babysitter Code ........................................................ 22 Backup Battery .................................................. 10, 39 Button Transmitters ................................................. 13 CDMA Cellular Communications Module .......... 11 Communication Modules ......................................... 11 Contact ID Event Log Codes ........................ 26, 27 Contact ID Reporting .............................................. 39 Contacting Technical Support ............................. 41 Devices ............................................................................ 2 Duress Code ............................................................... 22 Enter Installer Programming Mode .................... 18 Enter/Change The Master Code ......................... 22 Entry Delay ................................................................. 20 Entry/Exit Burglary .................................................. 20 Exit Delay ..................................................... 20, 28, 38 Exit Programming Mode ......................................... 19 GSM Cellular Communications Module .............. 11 Home Screen ............................................................... 16 House ID Code ............................................................ 13 House Identification ................................................. 13 Installer Code ............................................................. 22 Installer Tools Menu Screen ................................... 18 Installing Wireless Zones ........................................ 14 Key/Touchscreen Operation ................................ 22 Liquid Crystal Display (LCD) Touch-Screen ... 15 Loading Factory Defaults ....................................... 19 LYRIC-3G ....................................................................... 11 LYRIC-CDMA ................................................................ 11 Master Code ............................................................... 22 Master Security Code.............................................. 22 User Security Code .................................................. 22 Master User Tools Screen ....................................... 17 Memory of Alarm ...................................................... 22 Navigating Menus ................................................ 15, 17 Navigation Keys ......................................................... 16 News ............................................................................... 16 Operator Commands............................................... 25 Panic Key/Icons ........................................................ 22 Plug-In Power Supply ............................................. 10 Range ............................................................................. 13 Reboot .......................................................................... 29 Rebooting the System ............................................ 29 Regulatory Agency Statements .......................... 36 Reset Master User Code ......................................... 23 RF House Code ........................................................... 13 Secondary User Codes ........................................... 22 Security Codes ........................................................... 22 Security Screen .......................................................... 17 Programming Default Tables ................. 30, 31, 32 Sixfob ............................................................................. 13 Six Series Transmitters ......................................... 13 Sniffer Mode ............................................................... 28 Specifications ............................................................. 39 Super High Capacity Battery ................................. 11 Supervised RF ............................................................. 13 System Features .................................................... 5, 6 System Operation ..................................................... 22 System Standby Screen .......................................... 18 Technical Support ..................................................... 41 Test Modes .................................................................. 28 Testing the System ........................................... 28, 29 Touch-Screen Display .............................................. 15 Traffic ............................................................................. 16 Transmitter Battery Life .......................................... 13 Transmitter Input Type ............................................ 13 Transmitter Loop Numbers ................................... 14 Transmitter Supervision .......................................... 13 Unsupervised Button ................................................ 13 Unsupervised RF ........................................................ 13 Wall Mounting ........................................................ 8, 10 Wireless Keys .............................................................. 13 Wireless Zones ........................................................... 13 World Wide Web Address ..................................... 41 Zone Discovery.......................................................... 29 Zone Programming Default Values ................... 34 Zone Response Type Definitions ....................... 20 Zone Response Type Matrix ................................. 35
- 40 -
Lyric Controller Installation and Reference Guide LYRIC GATEWAY RESIDENTIAL BURGLAR AND FIRE ALARM CONTROL PANEL SUMMARY OF CONNECTIONS Notes: Connection of the fire alarm signal to a fire alarm headquarters or a Central Station shall be permitted with the approval of the local authority having jurisdiction. The burglar alarm signal shall not be connected to a police emergency number. The System must be checked by a qualified technician once every three years
- 41 -
SUPPORT, WARRANTY, & PATENT INFORMATION For the latest documentation and online support information, please go to:
https://mywebtech.honeywell.com/
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa. For patent information, see www.honeywell.com/patents MyWebTech Warranty Patents 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Copyright 2016 Honeywell International Inc. www.honeywell.com/security 800-21666U 800-21666 10/16 Rev. A
1 2 3 | Quick User Guide | Users Manual | 2.62 MiB |
User Reference Guide Ref: LCP300-L/LCP300-LC 800-21670 10/16 Rev A Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for use with your security system. Your Honeywell security system is not designed for use with any device that may be attached to your security system's control or other communicating bus if Honeywell has not approved such device for use with your security system. Use of any such unauthorized device may cause damage or compromise the performance of your security system and affect the validity of your Honeywell limited warranty. When you purchase devices that have been manufactured or approved by Honeywell, you acquire the assurance that these devices have been thoroughly tested to ensure optimum performance when used with your Honeywell security system. Lyric Lock Your system supports advanced features designed to keep it functioning optimally. These capabilities include: the ability to interact with Honeywell and your dealers network for the setup and programming of its features, support for remote software updates and the ability (when enabled by your monitoring dealer) to enhance your security by preventing an unauthorized takeover of the system by another monitoring company. In the event that your dealer has enabled the feature to prevent an unauthorized takeover and you wish to authorize a new company to take over your system, you may request that Honeywell remotely disable this feature. Honeywell will require documentation that you have attempted to contact your existing security dealer and that they have failed to respond, or failed to agree to your request. TABLE OF CONTENTS OVERVIEW ..............................................................................................................ERROR! BOOKMARK NOT DEFINED. About This Guide ...................................................................................................................................... Error! Bookmark not defined. Basic Functions ..................................................................................................................................................................................................... 5 About the Control Panel ................................................................................................................................................................................. 10 Home Button Status Indications .................................................................................................................................................................. 10 The Tools Menu .................................................................................................................................................................................................. 12 SECURITY ........................................................................................................................................................................................ 14 Security Features ............................................................................................................................................................................................... 14 False Alarm Prevention .......................................................................................................................... Error! Bookmark not defined. Arming the System .................................................................................................................................. Error! Bookmark not defined. Disarming the System ...................................................................................................................................................................................... 17 Bypassing Protection Zones .......................................................................................................................................................................... 17 Entry and Exit Delays ....................................................................................................................................................................................... 18 Emergency Alarms ............................................................................................................................................................................................ 19 Chimes/Voice Annunciations ....................................................................................................................................................................... 20 Audio Alarm Verification (Two-Way Voice) ............................................................................................................................................ 21 Built-In Camera ................................................................................................................................................................................................... 21 AUTOMATION: Z-WAVE AND OTHER DEVICES ............................................................................................................. 23 Working with Z-Wave Devices .................................................................................................................................................................... 23 Garage Doors ..................................................................................................................................................................................................... 30 AUTOMATION: SMART SCENES.............................................................................................................................................. 31 Smart Scenes and User Access .................................................................................................................................................................... 31 Creating a Smart Scene .................................................................................................................................................................................. 32 Hold ........................................................................................................................................................................................................................ 35 Run ......................................................................................................................................................................................................................... 35 Show (Review) ................................................................................................................................................................................................... 35 AUTOMATION: VOICE COMMAND ................................................................ERROR! BOOKMARK NOT DEFINED. Setup ............................................................................................................................................................. Error! Bookmark not defined. Voice Command Assignment ............................................................................................................... Error! Bookmark not defined. Using Voice Command ........................................................................................................................... Error! Bookmark not defined. Counter (Sensitivity Settings) .............................................................................................................. Error! Bookmark not defined. VIDEO ................................................................................................................................................................................................ 37 Viewing and Naming Cameras ..................................................................................................................................................................... 37 Adding a Camera .............................................................................................................................................................................................. 37 Video Recovery ................................................................................................................................................................................................. 38 USERS AND SECURITY CODES .............................................................................................................................................. 39 User Codes .......................................................................................................................................................................................................... 39 Duress Code ........................................................................................................................................................................................................ 39 Adding Users and Assigning Codes........................................................................................................................................................... 40 Changing Security Codes or the Duress Code ...................................................................................................................................... 40 Deleting a User .................................................................................................................................................................................................. 40 User Settings ....................................................................................................................................................................................................... 41 SYSTEM SETTINGS ..................................................................................................................................................................... 43 Brightness/Volume/Cleaning ....................................................................................................................................................................... 43 Wi-Fi Configuration ......................................................................................................................................................................................... 43 Software Updates ............................................................................................................................................................................................. 44 Slide Show ................................................................................................................................................... Error! Bookmark not defined. Date / Time ......................................................................................................................................................................................................... 45 Events .................................................................................................................................................................................................................... 45 Keypad .................................................................................................................................................................................................................. 45 TESTING YOUR SYSTEM .......................................................................................................................................................... 46 Testing Sensors (Walk Test) ......................................................................................................................................................................... 46 Testing Communications ............................................................................................................................................................................... 47 Reboot .................................................................................................................................................................................................................. 47 MAINTENANCE ............................................................................................................................................................................ 48 Care and Cleaning ............................................................................................................................................................................................ 48 Battery Replacement ....................................................................................................................................................................................... 48 Communication Module Replacement ...................................................................................................................................................... 50 3 SYSTEM DISPLAY AND BUTTONS ......................................................................................................................................... 51 WIRELESS KEYS ........................................................................................................................................................................... 53 Key Assignments .............................................................................................................................................................................................. 53 SiXFOB Wireless Key Status Indications ................................................................................................................................................. 53 EVENT LOG CODES ................................................................................................................................................................... 54 GLOSSARY ...................................................................................................................................................................................... 56 FIRE/CO ALARM SYSTEM ........................................................................................................................................................ 57 In Case of Fire .................................................................................................................................................................................................... 57 In Case of Carbon Monoxide Alarm ........................................................................................................................................................... 57 Silencing a Fire/Carbon Monoxide Alarm ................................................................................................................................................ 57 NATIONAL FIRE PROTECTION ASSOCIATION SMOKE DETECTOR RECOMMENDATIONS ........................ 58 Emergency Evacuation ................................................................................................................................................................................... 59 REGULATORY AGENCY STATEMENTS .............................................................................................................................. 60 OWNER'S INSURANCE PREMIUM CREDIT REQUEST .................................................................................................... 61 LIMITATIONS OF THIS ALARM SYSTEM ............................................................................................................................. 63 YOUR SYSTEM INFORMATION .............................................................................................................................................. 64 TWO YEAR LIMITED WARRANTY ......................................................................................................................................... 67 4 Overview The Lyric Gateway combines a security system and home automation with flexibility to operate your system locally using Wi-Fi connection or remotely over the internet using smart devices and easy to use Apps. Your system can include wireless sensors to provide burglary protection and smoke and combustion detectors to provide early fire and carbon monoxide (CO) warnings (if installed). Your Gateway system monitors sensors and system status to initiate alarms and generate alerts. The system can also send alarm and status messages to a central monitoring station via the cellular phone network or the Internet, if programmed to do so. Convenient methods of operating the Gateway include the following:
The Gateways touchpad Your Total Connect Remote Services account (for local and remote access) The MyHome Gateway App (for local access) Optional wireless keys (key fobs), Lyric keypads and smart devices. Download and install the MyHome Gateway App and the Total Connect App from your smart devices App Store. NOTE: The MyHome Gateway App requires connection to the Gateway via the premises Wi-Fi router (Ethernet cable or Wi-Fi). The Total Connect App requires internet or cellular connection for remote access to the Gateway. About This Guide Throughout the User Guide, icons help you easily identify which control options are available for different system features:
This icon Means, you can operate the feature from the Gateway touchpad. locally from your smart device using the MyHome Gateway App. locally or remotely from your computer, or smart device using your Total Connect Remote Services account. For smart devices, download the Total Connect App. or or Optional wireless keys (key fobs), Lyric keypads or smart devices In the Navigating with the MyHome Gateway App section, various menu commands are also listed for operating various options. For example, if you see:
Home > Security > Tools > Users This means: From the MyHome Gateway App Home screen, select Security. From the Security menu, select Tools. From the Tools menu, select Users. Note that the illustrations in this document may differ slightly from your system. 5 Basic System Functions Security Arm in Home mode Arm in Away mode Press and enter your user code and enter your user code Disarm system & silence alarms and enter your user code. Repeat to silence alarms/alerts Emergency Then press:
or notifies the monitoring company of the emergency type (if programmed to do so) Press Access Security features Arm in Away mode Arm in Home mode on the Home screen and enter your user code and enter your user code Disarm system & silence alarms Emergency (Panic) Video and enter your user code. Repeat to silence alarms/alerts Use the Gateway Touchpad Emergency options or, if programmed to do so, use your wireless key (key fob) to signal an emergency. Press on the Home screen to view and configure Wi-Fi cameras Control Panel Settings Press
(Settings) on the Home screen Gateway key brightness Gateway volume Voice announcements volume Chime volume (count-down beeps, other sounds) Automation Features Select Brightness and use the slider Select Volume and use the slider Select or deselect VOICE Select or deselect CHIME Press Operate & manage Z-Wave devices Create & manage Smart Scenes on the Home screen on the Home screen 6 Common Master User Functions Add, delete or modify user codes View a list of System Events System tests Set Date and Time View a list of smart devices paired to your Gateway Network Config Press
(Security) then code.
, (Tools) and enter your Master User
(Users)
(Events)
(Advanced) and select Walk Test or Comm. Test
(Date Time)
(Keypad)
(WiFi Config) 7 Security Features NOTES: For the Lyric Gateway to report alarms over the internet, your Wi-Fi network MUST have power at all times. You must arm your security system in order for it to sound alarms. Sensors and Zones Fire Protection Carbon Monoxide Burglary Protection Security
(User) Codes User Code Error
(Keypad Lockout) Alarms Your systems sensors are assigned to numbered zones that correspond to areas of your home. For example, the sensor on an entry/exit door might be assigned to Zone 03, a device in a bedroom to Zone 06, and so on. When alarms or trouble conditions occur, you can find information about the zone number and a description of the sensor involved using the MyHome Gateway App.
[Home > Security > Tools . Master User Code > Events]
Fire protection is always active when the system is operating normally. An alarm sounds if a fire condition is detected. See Fire/CO Alarm System for important information about fire protection, smoke detectors and planning emergency exit routes. Carbon monoxide (CO) detectors, if installed, are always active and sound an alarm if a carbon monoxide condition is detected. See Fire/CO Alarm System for more information. Gateway provides HOME and AWAY burglary protection. HOME mode protects windows and exterior doors, allowing you to move around inside your home without setting off an alarm. (This mode may be referred to As STAY mode in Total Connect.) AWAY mode protects the entire premises, including interior motion detectors, if present. Both modes offer an entry delay period that allows you to reenter the home without setting off an alarm. For long periods such as vacations, the entry delay can be turned off while arming the system. Gateway also allows you to Bypass selected sensors before arming the system. The system also features Chime mode, which can alert you to the opening of protected doors and windows while the system is disarmed. At the time of installation, the installer asks the homeowner to choose a personal 4-digit security code, known as the Master User code. Other users can be added, typically with less control over the system than the Master User. See Users and Security Codes. A user code is required when arming or disarming and for some other functions. If X invalid user codes are entered, the system locks out additional code entry attempts for a period of time. Additional user code entry attempts will not be accepted until the lock out period ends. NOTE: The system can be Quick Armed while in Lockout mode, but cannot be disarmed. Alarms are signaled by the internal sounders on the Gateway Touchpad and on the smart devices running MyHome Gateway App. (Alarms will also sound on external sirens if used). The Gateway Touchpads status shield and Alert blink red; the MyHome Gateway App screen indicates Alarm and shows the zone(s) where the alarm has occurred. After 15 seconds, the sounder stops temporarily and the system begins voice announcements of relevant zone information. After the zones are announced, the panels sounder resumes sounding. Alarm sounds and voice announcements alternate until the system is disarmed or until alarm bell timeout occurs. If the system is connected to central monitoring, an alarm message is sent. To silence the sounder, disarm the system. The zone(s) causing the alarm remain displayed on the MyHome Gateway App screen, indicating Memory Of Alarm an Alarm is held in memory. See Clearing an Emergency Alarm for more about clearing memory of alarm. Audio Alarm Verification Allows your central monitoring station to listen to or talk with individual(s) on the premises (if programmed to do so). 8 False Alarm Prevention Many false alarms are caused by minor problems, such as a door or window left open when exiting the home. Gateway includes several features to help prevent false alarms. Note that some are optional or must be programmed by the installer. Disabling these features may increase security, but may also increase the chance of false alarms. Your installer can help you decide how to use and customize these features. A brief explanation of false alarm prevention features follows, along with advice on what to do if false alarms occur. Entry Delay Exit Delay When the system is armed, Entry Delay is the time period allowed to disarm the system with a user code after an entry door is opened. Failure to disarm the system during the Entry Delay causes an alarm. The delay period is set by your installer. When arming the system, the Exit Delay period begins, allowing household members to exit through entry/exit doors without triggering an alarm. Entry/exit doors must be closed before the exit delay ends. The delay period is set by your installer. After a false alarm, disarm the system and contact your monitoring company. They will verify your security code or password, preventing unnecessary calls for emergency response. Exit Time Restart If you leave the premises and enter again before the exit delay has expired, the exit delay restarts, giving you more time to leave without causing an alarm. With 10 seconds left to exit, the Gateway begins beeping quickly, indicating that an alarm will occur if you dont exit or disarm the system immediately. If this occurs, disarm the system and arm it again when you are ready to leave. You can restart the Exit Delay by pressing Restart Timer on the MyHome Gateway App screen. Gateway is programmed to wait for a brief period between sounding a burglary alarm on the premises and sending an alarm message to your monitoring company. This delay allows you to disarm the system before an alarm message is sent in error. False alarms can be caused by leaving the house and forgetting to close the door. If this happens, Gateway sounds an alarm and displays an Exit Error. The alarm reporting delay gives you time to disarm the system before an alarm message is sent. Press Silent Exit on the MyHome Gateway App screen to mute the beeping sound for exit countdowns in most situations. Voice confirmation of arming status is not muted. Silent Exit doubles the Exit Delay time. Press Quick Exit on the MyHome Gateway App screen when the system has been armed and someone needs to leave the premises. This restarts the exit delay, allowing you to exit the premises without having to disarm and re-arm the system. Exit Delay Restart/Reset Alarm Reporting Delay Exit Alarms Silent Exit Quick Exit 9 About the Gateway Touchpad The Lyric Gateway Touchpad is designed to operate your basic security features. Also, you can quickly see your system status by which items on the Touchpad are lit. The System Status Shield and arming options are always lit to show system status at a glance. Emergency is also always lit, so it is easy to find, when needed. The other options on the touchpad light only when needed. NOTE:
If the Gateway loses AC power, Alert begins to blink slowly after 15 minutes on battery backup and all other lights on the Gateway are off. In this situation, although the Emergency light is off, Emergency functions remain available. System Status Shield Indications The System Status Shield indicates system status with these behaviors:
System is ready to be armed System is not ready to be armed. System is armed Green, steady Green, blinking slowly Red, steady Red, blinking slowly Red, blinking rapidly Entry delay countdown started; enter your user code to disarm the system System is in Alarm If programmed to do so, two-way Voice Communication may be active when the system is in Alarm. [See your installer to program this feature.]
System is in user code entry mode White, steady See the Emergency section for information on silent alarms. 10 System Sounds Function Beeping Volume Alarms Description accompanies entry/exit countdowns, pressed buttons and other functions*
adjustable for voice announcements, chimes and most sounds (adjusted through the MyHome Gateway App) signaled by the Gateways built-in sounder and external sirens/speakers (if installed). Alarm volume is not adjustable. System Arming Options and LEDs When any of the arming options is pressed, the numbers light. Use the Gateway for basic security functions:
Press and enter The system enter your user code Arms in Away mode for 3 seconds
---
Quick Arms in Away mode enter your user code Arms in Home (Stay) mode for 3 seconds
---
Quick Arms in Home (Stay) mode enter your user code Is Disarmed System Emergency Options Depending on your system set up, when an Emergency Type option is pressed, emergency messages can be sent to your monitoring company (if programmed to do so). Refer to the Emergency Alarms section of the Navigating with the MyHome Gateway App for additional details. Press Then The system Emergency Type options appear. or The system sends an emergency message to the monitoring company, if programmed up to do so. Cancel must be pressed while blinking to cancel the Emergency before it is sent. To Cancel and Clear an Emergency Alarm that has been triggered The Alarm will silence and the system will announce the status. Check for alarm details on MyHome Gateway App or Total Connect Remote Services. Enter a User Code again to clear alarms. User Code System Alert If the system experiences a condition, such as AC power loss, connectivity or a communication problem, the Alert blinks. Press Then The Gateway announces the system Alert condition and suggested actions. 11 Software Update Notifications Software updates for the Gateway are published periodically. Certain critical updates are installed automatically. After updates of this type, information about the update are found by using the Messages option on the MyHome Gateway App Home screen ???. Navigating with the MyHome Gateway App Use the MyHome Gateway App to manage your System Security, Automation, Smart Scenes, Video and Settings:
The Home Menu Function Press Security Automation Video Smart Scenes Settings Then Select from the options on the next screen. Allows you to... Operate and manage the security features and access other features of your Gateway system.
---
Manually operate your Z-Wave devices and
---
Master User Code
---
Add or delete Z-Wave Devices View and configure system cameras;
manage video recovery functions View and run automation scenes to operate your system for convenience, comfort, energy savings and security*
Adjust the Gateway touchpad and LED brightness and the announcements and chime volume
* Smart Scenes are created and deleted using Total Connect Remote Services. NOTE: Pressing Home from any screen returns you to this Home screen. 12 The Tools Menu Home > Security > Tools NOTE: The Master User code is required to access Tools. This menu offers access to most of Gateways important settings and maintenance functions.:
The Master User can add/remove other users and control users access to features. See Users and Security Codes. View and export (?) system event logs. See Events. Access to software upgrades, tests and user maintenance functions. Includes features found in Maintenance and System Settings. Manage smart devices paired to your Gateway. See Keypad. Set the systems calendar and clock. See Date and Time. Configure Wi-Fi connection to the Gateway. See Network Configuration. Return to the Security menu. Users Events Advanced Keypad Date/Time Network Config
(Back Arrow) 13 Security Home > Security IMPORTANT If the Gateway is beeping rapidly when you enter the premises, an alarm has occurred and an intruder may still be nearby. LEAVE IMMEDIATELY and CONTACT THE POLICE from a safe location. Security Features NOTES: For the Lyric Gateway to report alarms over the internet, your Wi-Fi network MUST have power at all times. You must arm your security system in order for it to sound alarms. Arming the System The MyHome Gateway App displays the system arming status, top and center of the screen:
Ready to Arm = the system is ready to be armed. Not Ready To Arm-Fault = one or more zones are faulted. The system cannot be armed until all zone faults are fixed or bypassed. Armed [Home, Away, Custom, etc.] = the system is armed, and arming mode description. Before arming your system, all protected doors, windows, and other protection zones should be closed or bypassed (see Bypassing Protection Zones). To change the volume of countdown sounds and security status voice announcements, see System Settings. 14 Arming states include Arm Away Arm Home Arm Custom Bypass Arm Night Instant Quick Arm For times when no one is home; protects all perimeter and interior zones. For times when the house is occupied; protects only perimeter zones. Arms the system with pre-selected zones bypassed. This feature allows you to arm the system while intentionally leaving selected zones unprotected. For times when the house is occupied; protects perimeter zones and selected interior motion sensors if used. Other interior zones are unprotected. Enabled by your installer and only used with interior motion sensors. For times when Entry/Exit doors are not expected to open at all. Entry Delay is eliminated. When the system is armed, an alarm occurs immediately if an exterior door is opened. Used to arm the system in any mode without entering a user code, if programmed NOTE: A user code is always needed to disarm the system. Auto Home If you arm the system in the Away mode but no one exits, the alarm system automatically changes to the Home mode. This helps to prevent unwanted alarms when someone remains on the premises. Disarm the system and Arm Away again when you are ready to leave. This option is enabled by your installer. Arm Away Security > Arm Away By default, this modes exit delay countdown is accompanied by a beeping sound. For a silent exit, press Silent Exit first. The system beeps twice and announces Armed Away; exit now. The exit delay countdown begins. Press Restart Timer if you need more time to leave. Leave the premises and close the door before the countdown ends. The system arms in Away mode. (Door and window sensors and interior motion sensors are active.) 15 Arm Home Security > Arm Home By default, this modes exit delay countdown is silent. The system beeps three times and announces Armed Home; exit now. The exit delay countdown begins. Press Restart Timer if you need more time to leave. The system arms in Home mode. Door and window sensors are active, but interior motion sensors are not active. Arm Custom Security > Arm Custom Use this option to pre-set zones for bypass when arming the system. You can also enable or disable the entry delay. 1. Select Arm Custom to display a list of zones. 2. Select the zones you wish to bypass when arming the system. 3. Select Arm Custom on the zone list screen. 4. A numerical keypad appears. Select Entry Delay if desired. (See Instant Mode for more about disabling Entry Delay.) 5. Arm the system by entering a user code. 6. The exit delay countdown begins. 7. If leaving, leave the premises and close the door. Bypassed zones are left unprotected. NOTE: The next time Arm Custom is used, the same zones that were previously selected are highlighted on the zone list screen. If desired, select different zones for custom arming. Instant Mode Security > Arm Custom In Instant mode, an alarm occurs immediately when a protected Entry/Exit is opened. There is no delay during which a code can be entered to disarm the system. If any zones have been previously set for bypass, deselect them. 1. Select Arm Custom to display the zone list screen. 2. 3. Press Arm Custom. 4. When the keypad appears, de-select Entry Delay. 5. Enter a user code to arm the system and leave the premises during exit delay. Arm Night Security > Arm Home Arm Night must be enabled by your security professional. 1. Select Arm Home to display the keypad. 2. Select Arm Night and then enter a user code. 3. The system beeps and announces Armed Night Home mode. Exit delay begins. Press Restart Timer if you need more time to leave. 4. The system arms in Arm Night mode. Doors and windows and pre-selected interior zones are active. 16 Disarming the System Security > Disarm NOTE: Disarming the system also silences audible alarms and trouble alerts. IMPORTANT SECURITY NOTICE Your wireless key (key fob) is similar to your keys or access card. If lost or stolen, another person can compromise your security system. Immediately notify your Dealer/Installer of a lost or stolen wireless key. The Dealer/Installer will then remove the wireless key programming from the security system. To disarm your security system:
The system beeps and announces Disarmed, followed by alerts about system readiness, if any. The announcement Check system indicates a faulted sensor or problems in the Gateway itself. In most situations, if a valid user code is not entered within 30 seconds of pressing Disarm, the Home screen reappears, and the system remains armed. NOTES: If a valid code is not entered by the time the entry delay ends, an alarm occurs. The Guest code and the Installer code can only disarm the system if that code was used to arm the system. If the Quick Arm option has been used, neither the Guest Code nor Installer Code can disarm the system. User Code Error: When the screen displays User Code Error, it means too many invalid user codes have been entered. The system will not accept additional user code entries for 15 minutes (lockout period). Bypassing Protection Zones Bypass allows arming the system while intentionally leaving selected zones unprotected. Bypassed zones will not trigger an alarm. NOTES: Fire and Carbon Monoxide (CO) and Emergency zones cannot be bypassed. Bypassed zones are automatically un-bypassed when the system is disarmed. To Bypass zones:
1. Before arming the system, press Zones on the Security menu. A list of your systems zones appears. Faulted (open) zones are shown in red or orange. Use the up and down arrows to scroll through the list of zones. 2. Select the zone(s) to be bypassed. 3. Press Bypass at the bottom of the screen. A keypad appears. At the bottom of the screen, you can Bypass All Faulted, which selects all zones with faults or other issues. Press Select All to toggle through options for selecting zones. 4. Enter a user code. The zone list reappears with the Bypass icon shown for the affected zones. 5. Arm the system as usual. Press Clear Bypass to un-bypass any previously bypassed zones. Any zones with faults must be addressed before arming the system. 17 Entry and Exit Delays NOTE: Entry and exit delay times are programmed by your installer. There is room to jot them down in Your System Information, near the end of this guide. Entry Delay Entry delay allows time to disarm the system when entering the premises. If the system is not disarmed before the entry delay period ends, an alarm occurs. If programmed, the Gateway beeps during the entry delay period as a reminder to disarm the system. Two different entry delay periods can be programmed. The first is for the primary entrance, typically, the front door. The second can be used for a secondary entrance, where more time might be needed to walk to the Gateway to disarm the system. Exit Delay Exit delay begins immediately after the system is armed, providing time to leave through the designated exit door without causing an alarm. In most situations, the MyHome Gateway App screen displays a countdown of the remaining time. The exit door must be closed before the end of the exit delay. Typically, the system beeps slowly when counting down to Arm Away and the beeping speeds up during the last 10 seconds of the delay period. The exit beeps cannot be silenced unless Silent Exit is selected. Restart Exit Delay The Restart Timer option appears only if the option has been programmed by the installer. Exit delay can be restarted once. Exit Alarm This option helps minimize false alarms sent to the monitoring company. Exit Alarm must be enabled by your installer. Exit delay begins whenever the system is armed. If an exterior door or protected interior zone is faulted during the exit delay (and remains faulted when the exit delay ends), an exit alarm occurs and an entry delay countdown begins. If the system is disarmed before the entry delay ends, the alarm sound stops and the message Alarm Cancelled and any faulted zones appear. No message is sent to the monitoring company. Any open zones must be secured before the exit alarm condition can be cleared. To clear the display, press Disarm and enter a security code. If the system is not disarmed before the entry delay ends, and an entry/exit door or interior zone is still open, the alarm sound continues and an Exit Alarm message is sent to the alarm monitoring company, along with a Recent Close message (if the Recent Close option is enabled). The message Alarm Exit Error appears. Faulted zones are also displayed. The alarm will continue to sound until the system is disarmed or timeout occurs. To stop the alarm, disarm the system. The message Alarm Cancelled will be displayed. Alarm and faulted zones continue to be displayed. To clear the display, press Disarm and re-enter the security code. An exit alarm (Alarm Entry Exit) also occurs if an entry/exit door or interior zone is faulted within two minutes after the end of the exit delay. 18 Emergency Alarms Available Emergency modes may vary, depending on the options programmed by your installer. Use the Gateway Touchpad to trigger an Emergency. An Emergency can be canceled or cleared from the Gateway Touchpad, the MyHome Gateway App or Total Connect. IMPORTANT Activating an Emergency Alarm 1. Press 2. Press the appropriate Emergency type option on the Touchpad. on the Gateway. Depending on the Emergency mode selected, an alarm tone sounds and the appropriate alarm icon appears on the MyHome Gateway screen. Pressing Police can send a silent message to your monitoring company if programmed to do so. Verify this setting with your installer. Common Emergency Icons Fire Police Medical Local Alerts the monitoring company that a fire condition exists. (Displays Fire Alarm 995 Main Fire) Alerts the monitoring company that a police emergency exists.
(Displays Alarm 999 Police, default is silent) If programmed, alerts the monitoring company to other types of emergency.
(Displays Alarm 996 Main Medical) Activates sirens and sounders on premises without alerting the monitoring company.
(Displays zone 998) Types of Emergency Alarms Silent emergency
(silent alarm) Sends an alarm signal to the monitoring company, but triggers no audible alarms or display (on either the Gateway Touchpad or MyHome Gateway screen.) Requires connection to a monitoring company. Audible emergency
(audible alarm) Sends an emergency message to the monitoring company, if connected. A loud, steady tone sounds at the Gateway and external sounders if connected, and an alarm appears on the MyHome Gateway App screen. Personal emergency or Aux alarm Sends an emergency message to the monitoring company if connected and sounds at the Gateway and MyHome Gateway App, but not at external sounders. An alarm icon appears on MyHome Gateway. Fire alarm Sends a fire alarm message to the monitoring company if connected. A unique tone sounds at the Gateway and MyHomeGateway and external sounders are activated if connected. A Fire alarm icon appears on MyHome Gateway. Local alarm If programmed, activates the sirens and sounders on the premises without sending a message to the monitoring company. Cancelling an Emergency Alarm from MyHome Gateway Depending on the type of Emergency alarm in effect, a keypad may appear immediately after the alarm is initiated. 1. Enter a user code to cancel the alarm. 2. The audible alarms stop and Alarm Cancel appears. If a silent alarm has been activated and the Home screen is displayed:
1. Select Security on the Home screen. Typically, a Disarm icon appears; a Security status message such as Alarm may be displayed. 2. Press Disarm and enter a user code. 3. The screen changes to the normal Security menu. 19 Clearing an Emergency Alarm After a Emergency alarm is cancelled, the Gateway continues to display zone information associated with the alarm (this feature is known as Memory of Alarm). To cancel and silence the alarm, enter a user code. To clear memory of alarm on the screen, enter the user code again. Memory of alarm can also be dismissed with these steps:
1. Cancel and silence the alarm with a user code as above. 2. Select Zones on the Security menu. The zone number associated with the type of alarm appears. 3. Press Clear Alarms at the bottom of the screen. 4. Enter a user code. The Zones screen displays No items to display!
5. Press to return to the Security menu or press the Home button. Chimes/Voice Annunciations The Chime feature is intended for convenience and is not intended for life safety purposes or pool alarm and does not meet the requirements of UL 2017. IMPORTANT Volume/Mute Home > Settings NOTES: Chime and voice volume/muting can only be changed when the system is disarmed. Voice annunciations are controlled by enabling or disabling Chimes. Voice annunciations should not be confused with Gateways Error! Reference source not found. or Two-Way Voice (Audio Alarm Verification) features. Gateway can give audible notifications when a protected zone opens while the system is disarmed. With Chimes enabled three beeps (or a selectable tone) sound at the Gateway when a protected zone is opened. If programmed, a voice announcement also sounds. 1. On the Home screen, select Settings. 2. Select Chime to enable chime sounds and voice annunciations. To mute all, de-select. For chime sounds only, de-select Voice. 3. Adjust volume with the slider. 4. Press Save. Setting Chime Sounds Home > Security > Zones NOTES: Chime sounds can only be changed when the system is disarmed. Sounds can be changed only for door, window and motion sensors. Sounds associated with smoke and CO detectors cannot be changed. Different sounds can be assigned to the sensors in your system. 1. On the Zones menu, press Select All repeatedly to choose Select Chime. A list of sensors appears. 2. Select a sensor. The Gateway displays available sounds. 3. Press repeatedly to choose a sound. (Options include Disabled.) 4. Press to save your selection and return to the Security menu. 20 Audio Alarm Verification (Two-Way Voice) This feature allows your central monitoring station to listen to or talk with individual(s) on the premises when an alarm has occurred (if programmed). NOTES: System announcements are disabled when this feature is active. Fire and CO alarms will prevent Audio Alarm Verification from operating. New Fire or CO alarms will terminate Audio Alarm Verification operation. Burglar alarms occurring during Audio Alarm Verification operation do not interrupt operation and are reported immediately after operation concludes. Audio Alarm Verification modes are controlled by the central station. 21 22 Automation: Z-Wave and Other Devices Home > Automation IMPORTANT evaluated by compliance agency. Automation can ONLY be used for lifestyle enhancement. It must not be used for personal safety or property protection. Working with Z-Wave Devices NOTE Z-Wave automation functionality is supplementary only and has not been Z-Wave technology is designed to automate devices in a home control network. The Lyric Gateway is a security enabled Z-Wave device that supports Z-Wave Network Wide Inclusion
(NWI) Mode. The Gateway and Z-Wave devices added to your system are linked together in a wireless network. Each device in the network is assigned a unique address and cannot be activated by a neighbor's Z-Wave controller. The Z-Wave network supports multiple controllers, allowing Z-
Wave remote controls to be used throughout the home. NOTE:
In some cases, a Z-Wave device might not report its status to the Lyric Gateway when an action is initiated at the device itself. This varies with the manufacturer. Press Automation on the Home screen. The Automation Management screen appears, initially displaying categories of Z-Wave devices. (Your MyHome Gateway Apps display may differ from these illustrations.) This screen may also display Press to see Failed Devices. See Failed Devices (Failed Nodes) for more information. Press the Down arrow for more options:
Consult your installer about the options available in your system. 23 Selecting a device category opens a list of devices in that category. An example of the Switch category is pictured. For most devices, status is indicated by the color of the icon. The Refresh button updates device status indications on the display. Operating Z-Wave Devices Manually 1. On the Automation Management screen, select one of the device categories. 2. Select the device you wish to operate. Controls appear. 3. Lighting controls might offer an On/Off button or a slide control for dimmers. 4. Thermostats may display temperature set points and energy-saving features. The options shown will vary with your device. 5. Operate the device as desired. 6. Press to return to the previous screen. Adding Z-Wave Devices (Include) NOTE:
When adding a device, it may be necessary to perform the Exclude procedure before the device can be Included successfully. 1. On the Automation Management screen, press the Down arrow. 2. Press Tools. 3. On-screen options appear, including Include Devices, Exclude Devices and Advanced Tools. (View Failed Devices may also appear.) 4. Select Include Devices. The panel enters Inclusion mode. Next, the panel displays Ready to Include device. Press the function button on device. 5. Press the devices Function button within 60 seconds. (Note that the location of the Function button varies with the device you are adding. See the devices instructions.) The panel displays Device Found. Please Wait. 6. To include additional devices, repeat step 5. OR Press Abort to complete the Inclusion process. 7. Press to return to the previous screen. Including Light Switches or Outlet Modules Install the receptacle, wall switch or lamp/appliance module before Including it in your system. Refer to the devices instructions for more information about installation. Z-Wave switches and outlet modules may vary. Refer to the devices instructions to ensure that it is Included properly in your system. 24 Including Door Locks IMPORTANT For security, Z-Wave door locks are encrypted, and enroll at low power transmission range (approximately 6 feet). This requires Including the lock before its installation in a door. Assemble the lock, connect necessary cables and install batteries according to the devices instructions. Be sure the door locks orientation/handedness is correct. Z-Wave door locks vary. Refer to the devices instructions to ensure that it is Included properly and to program a user code. After Inclusion, install the lock within recommended Z-Wave range (see Wireless Range for more information). NOTES: Program the 4-digit user code into the Gateway. When programming user codes into the Gateway, determine if the user will have access to the Z-Wave lock. If so, the user code will be transferred to the lock. If using a lock with Smart Scenes, automatic locking/re-locking features should be disabled. Due to Low Power Inclusion Mode of secure devices, Include the Z-Wave Lock first, if not using an Inclusion Tool/Remote Control. The lock should be installed before including other devices. During operation, the system will display JAMMED and will revert to Unlocked status if a jammed lock is detected. When performing a command directly from a thermostat or water shutoff valve, a change of status message may not appear at the Controller. Including Thermostats Install and test the thermostat before Including it in your system. Refer to the devices instructions for more information about installation. Honeywell is not responsible for property damages due to improper setting of thermostat modes. IMPORTANT NOTES: Some thermostats do not update temperature status automatically. When using Z-Wave thermostat control on the Gateway, the thermostats scheduling feature should not be used. When the HOLD button on the Gateways thermostat control screen is highlighted, Z-Wave scenes driven by Smart Scenes will not affect thermostat operation. Additionally, if your system is connected to remote services, the remote 7-day schedules will also not affect thermostat operation. For threshold monitoring to be configurable on the remote services and Z-Wave thermostat screens, the respective zones will first need to be assigned with a response type in zone programming. Threshold monitoring is not available on all thermostats. Both Zones for each respective thermostat must be programmed (for example, Zone 180 & 181 for thermostat #1, Zone 182 & 183 for thermostat #2 and Zone 184 &
185 for thermostat #3). When temperature is represented in Celsius, Gateway matches the temperature increment of the particular thermostat for Heat, Emergency Heat and Cool set points. Increments can be one degree or half degree, depending on the thermostat. If Celsius scale is used in the thermostat, the Gateway must also be set to Celsius scale. If the Energy Saving mode is set, the Gateway displays Energy Saving Heat/Cooling Setpoint Temperatures that are programmed at the thermostat. An additional Energy Saving function in the thermostat is used to set/unset the Energy Saving mode. 25 Lyric Gateway Z-Wave Thermostat Functions Button Mode Fan HOLD NORMAL NO SCHED Function Select between HEAT, COOL and OFF. Select between ON, CIRCULATE and AUTO. Allows temporary override of programmed Smart Scenes that may operate the thermostat. Allows selected thermostat to run programmed Smart Scenes. Prevents Smart Scenes from operating the selected thermostat Threshold Monitoring Enable/Disable Threshold Monitoring Feature (if available) Saving Off-
thermostats Energy Saving Saving On EDIT BACK Enables/disables Schedule Function. Used to edit Thermostat name. Used to return to Thermostats screen. the Thermostat Energy Saving Mode 1. On the Automation Management screen, select Thermostats. 2. Select the desired thermostat from the displayed list. 3. On the thermostat control screen, press the Saving Off button OR Saving On to activate or deactivate the thermostats Energy Saving Schedule Function when a heating or cooling operation is selected. Deleting Z-Wave Devices (Exclude) To delete (Exclude) a Z-Wave device:
1. On the Automation Management screen, press the 2. Press Tools. 3. Select Exclude Devices. 4. The panel enters Exclusion mode. Next, the panel displays Ready to Exclude device. arrow. Press the function button on device. 5. Press the devices Function button. 6. The device is excluded from the system and its information is displayed. 7. To delete another device, press Exclude on the right side of the screen. 8. Press to return to the previous screen(s). Editing Z-Wave Device Names OR 1. On the Automation Management screen, select the category that includes the device you want to rename. 2. Select the device in the displayed list. 3. The devices controls appear, showing the devices default name. 4. Press Edit on the right side of the screen. 5. A keyboard appears on the touchscreen. 6. Press Clear to delete the default name. 7. Enter a custom name, using as many as 14 characters. 8. Save the devices new name. 9. When you are finished editing, press to return to the previous screen(s). 26 Advanced Tools 1. From the Automation Management screen, open Tools. 2. Select Advanced Tools. 3. Enter the Master User code. The Advanced Tools screen appears:
View Enrolled Devices Press to display Z-Wave device information: System Index/name, Secured or Non-Secured, device type, device ID, manufacturer, node number. View Enrolled Controllers Press to display controller information: Primary or Secondary, Z-Wave Library Rev., Home ID, device type, device ID, node number, manufacturer, Secured or Non-Secured. Reset Controller Press to delete all Z-Wave nodes in the Gateway, and reset the Gateways Home ID. When prompted, press Yes to confirm. Note that resetting the Gateway does not delete/Exclude individual Z-Wave devices. Therefore, each device must be Excluded before being added/Included in the Gateway again. Pri. Controller Shift to Secondary Press to designate another controller (such as a Z-Wave remote control) as the Primary Controller. When the panel displays Shifting, start the Learn function on the secondary controller. Refer to the secondary controllers instructions for more information. NOTE: Both controllers can operate the systems Z-Wave devices, but only the Primary can Include/Exclude devices. Locking Door Press to have your system arm automatically when a Z-Wave door lock is locked. Press repeatedly to select Away mode, Home mode, Arm without Auto-Home mode or to Disable this option. Learn This function is usually performed on a control panel or Z-Wave remote control being added to the system as a secondary controller OR on a secondary controller being designated as Primary. Press after starting the Include or Shift Control function on the primary controller. All Devices Off Press to manually turn off all Z-Wave devices. Note that some thermostats will enter Setback mode. All Devices On Press to manually turn on all Z-Wave devices. NOTE: Some thermostats will exit Setback mode. 27 Failed Devices (Failed Nodes) When the system tries to operate a Z-Wave device that has no AC power or other problems, it is identified as a Failed Device. The system may take up to a minute after the operation to detect the failure. To view Failed Devices:
1. On the Automation Management screen, select View Failed Devices. The panel displays Failed Nodes Found!
2. Press OK. 3. The devices information is displayed. If multiple devices are listed, use the up and down arrows at right to view the entire list. NOTE: When troubleshooting, first make sure that power has been restored. If a device is defective or otherwise unavailable, use the Fix All option. 1. Select Fix All on the right side of the screen. The system displays This will delete all failed nodes. 2. Press Yes to confirm. Devices deleted with Fix All must be added to the system again. See Adding Z-Wave Devices (Include). Failed Z-Wave devices are also indicated by a screen or the Important Notes About Z-Wave Devices symbol appearing in gray on the Home screen. symbol on the Automation Management WARNING: NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT!
Z-Wave enabled devices should never be used to supply power to, or control the On/Off status of medical and/or life support equipment. Wireless Range This device complies with the Z-Wave standard of open-air, line of sight transmission distances of 100 feet. Actual performance in a home depends on the number of walls between the controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in the control network. Note that Z-Wave home control networks are designed to work properly alongside wireless security sensors, Wi-Fi, Bluetooth and other wireless devices. Some 900MHz wireless devices such as baby cams, wireless video devices and older cordless phones may cause interference and limit Z-Wave functionality. Things to consider regarding RF range:
Each wall or obstacle (refrigerators, large TVs, etc.) between the remote and the destination device can reduce the maximum range of 100 feet by approximately 25-30%. Brick, tile or concrete walls block more of the RF signal than walls made of wooden studs and drywall. Wall mounted Z-Wave devices installed in metal junction boxes will suffer a significant loss of range (approximately 20%) since the metal box blocks a large part of the RF signal. Additional Z-Wave Information Gateway can control up to 72 Z-Wave devices. The system supports a maximum of 232 nodes (?). Note that a node is created every time a device is Included, even if the device is being re-added to the system after being Excluded. This can cause the number of nodes in the system to exceed the number of actual devices. If the limit of 232 nodes is met and you need to add or re-Include more Z-Wave devices, use the Reset Gateway function. Be aware that resetting the controller deletes all of the systems nodes, requiring all devices to be Included again. Node numbers can be viewed by selecting Automation > Tools > Advanced Tools > View Enrolled Devices. Remember that the system may require the Master User code for access to Advanced Tools. 28 The system is not aware of door locks being enabled with any temporary user shutdown feature such as Vacation Mode. The system will continue to unlock a door if programmed to do so via Smart Scenes. Z-Wave door locks with thumbturns: Certain models allow a brief period in which the thumbturn can be operated manually before the device locks automatically. Locks of this type are not recommended for use with Smart Scenes. Z-Wave Compatibility Z-Wave devices vary; follow the instructions provided with the specific device when including and excluding devices into your Z-Wave network. NOTE: Not all Z-Wave devices have been tested. Some functions may produce unpredictable results. Door Locks Appliance Yale Real Living Push-Button Lever Lock HomeManageables Appliance Module Yale Real Living Touchscreen Lever Lock Wayne Dalton Small Appliance Module Yale Real Living Push-Button Deadbolt Lock Yale Real Living Touchscreen Deadbolt Lock GE Wireless Lighting Control Plug-In Appliance Module Cooper In-Wall Duplex Receptacle Module
(Model RF9505-TDS) Schlage Link Deadbolt Lock Schlage Link Lever Lock Kwikset Smartcode Lever lock Lights Leviton/ViziaRF+ Switches Leviton/ViziaRF+ Dimmers Kwikset Smartcode Deadbolt Lock Leviton/ViziaRF+ Plug-In Appliance Modules Thermostats GE Wireless Lighting Control Dimmers Honeywell Z-Wave Thermostat (ZWSTAT) GE Wireless Lighting Control Switches Wayne Dalton Z-Wave Thermostat GE Wireless Lighting Control Plug-In Appliance Modules Trane Z-Wave Thermostat Intermatic In-Wall Receptacle (Model HA01) Residential Control Systems Thermostat
(Model TZ45) Cooper Plug-in Lighting Switch Module (Model RFAPM) Intermatic InTouch Thermostat (Model CA8900) AEON Labs Lamp/Dimmer Module (Model DSC06106-ZWUS) Radio Thermostat Company of America
(Model CT30, CT32, CT100, CT101 and CT110) Remotec Lamp Dimmer Module (Model ZDS-
100US) Siren Window Shades FortrezZ SSA1/SSA2 Wireless Siren & Strobe Alarm Somfy ILT Series Water Valve FortrezZ WV-01 Wireless Z-Wave Water Valve EXISTING NETWORK NOTE: Z-Wave products from other manufacturers can be included (added) into the Gateway network. Z-Wave devices that are always powered can serve as repeaters regardless of manufacturer. USE OF THESE PRODUCTS IN COMBINATION WITH NON-HONEYWELL PRODUCTS IN A WIRELESS MESH NETWORK, OR TO ACCESS, MONITOR OR CONTROL DEVICES IN A WIRELESS MESH NETWORK VIA THE INTERNET OR ANOTHER EXTERNAL WIDE AREA NETWORK, MAY REQUIRE A SEPARATE LICENSE FROM SIPCO, LLC. FOR MORE INFORMATION, CONTACT SIPCO, LLC OR IPCO, LLC AT 8215 ROSWELL RD., BUILDING 900, SUITE 950, ATLANTA, GA 303350, OR AT WWW.SIPCOLLC.COM OR WWW.INTUSIQ.COM 29 Garage Doors Home > Automation > Garages Garage door operation from the Gateway requires installation of a garage door control kit. Consult your security professional for more information. The Lyric Gateway can remotely operate and monitor as many as four garage doors. The system can be armed when the garage door is opened. After it is closed, the zone will be monitored without providing burglary protection. The Gateway can automatically close garage doors if left open for more than a given time period
(Close in) or at a specified time (Close at). Garage doors can also be programmed for monitoring only. IMPORTANT Do not use Gateways garage door automation with any garage door opener that lacks the safety features required by U.S. federal safety standards (this includes any garage door opener model manufactured before January 1, 1993). A garage door opener that cannot detect an object and stop and reverse the door does not meet current U.S. federal safety standards. Your garage door opener also must signal before unattended door operation. For more information please consult your garage door opener manual. NOTE:
Press Switches on the Automation Management menu to configure new Z-Wave binary garage door openers. Ask your security professional for more information. Garage Door Operation from the Lyric Gateway 1. On the Home screen, select Automation. 2. On the Automation Management menu, press Garages. The Controller /MyHome Gateway App screen displays the Open/Closed status of your connected garage doors. 3. Select the garage door you wish to operate. 4. Press the button in the middle of the screen to open or close the garage door. Close in Close at Edit NOTE:
Use the keypad to set a specific time to wait before an open garage door closes automatically (maximum 12 hours and 59 minutes). Use leading zeroes when entering a number of hours less than 10 (09:15 or 00:45). Press Done to save. Use the keypad to set a specific time of day that an open garage door closes automatically. Remember to specify AM or PM. Press Done to save. Press to rename the selected garage door. Use the on-screen keypad and press Save. The Lyric Gateway does not support the status LED on the garage kits relay module (Honeywell 5877). 30 Automation: Smart Scenes Home > Smart Scenes Smart Scenes are used to automate Gateway functions for comfort, energy savings and security. Multiple settings can be put into effect with a single command. For example, selected lights can respond to a door opening or movement in the middle of the night. Climate settings can be controlled by your schedule and the security system can disarm automatically for expected visitors or babysitters. Selected functions can be restricted to the homeowner, and limited access given to children or guests. IMPORTANT When the Gateway is connected to a remote services account (e.g. Honeywell Total Connect), Smart Scenes can be created and modified ONLY via remote services. Smart Scenes can be created, deleted or edited at the Gateway ONLY by the Master User. See Smart Scenes and User Access for more about types of users and their access to different functions. Three types of Smart Scene can automate combinations of security and lifestyle settings:
Anytime: Initiated by users. Triggered: Initiated by the system in response to user-defined conditions. Scheduled: Initiated by the systems calendar and clock. Smart Scenes are frequently used in pairs. For example, a Smart Scene might be set to operate multiple devices, turning on lights and opening blinds or shades. A second Smart Scene could be used to return these devices to their Off or closed states. NOTES: As many as 100 Smart Scenes can be created at the Lyric Gateway or via Total Connect remote services and the MyHome Gateway App. You can modify (Edit), manually start (Run) and review (Show) Smart Scenes prior to operation. Scheduled and Triggered Smart Scenes can be paused with the Hold function. Setup details vary with each type of Smart Scene. Many buttons in Smart Scenes toggle through different options when pressed repeatedly. The system treats security actions such as Arm Away, Arm Home or Disarm separately from changes to lifestyle devices such as lights, locks and thermostats. Options that offer operations with both will display them in separate categories called Security and Devices. Smart Scenes and User Access NOTES: The Master User designates which types of user have access to each Smart Scene. See Users and Security Codes for more information on different types of users. Smart Scenes can be created, deleted or edited ONLY by the Master User. The Add New button is available only to the Master User. Regular users can Run and Show Smart Scenes created for Regular Users and Guests as well as those designated All Users. Guests can Run and Show Smart Scenes created for Guests as well as those designated All Users. To work with Smart Scenes:
1. Select Smart Scenes on the Home screen. A keypad appears. 2. Enter a user code to display the Smart Scenes menu. From here, Smart Scenes can be created or viewed by type. 31 Creating a Smart Scene Creating any Smart Scene involves these settings:
Name The type of trigger that initiates the Smart Scene The type of user who can manually run the Smart Scene The resulting action(s) that take place when the triggering events or conditions occur NOTE: Creating a Smart Scene should begin with giving it a Name. 1. Select Add New. (The default name that appears may differ from the illustration.) 2. Press Name. 3. Use the onscreen keyboard to enter a name and Save it. 4. Select the type of user who can run the Smart Scene. Choices include:
Master Regular Users Guest 5. Press Action Type to toggle through the types of Smart Scene. a. Anytime: Go to Step #6. b. Scheduled: Go to Step #7. c. Triggered: Go to Step #8. 6. Select Anytime. These options appear:
Name Action Type Who can run this Smart Scene? (User type) New Action a. Press New Action to define the systems response when the Smart Scene is triggered. b. When settings are complete, press until the Smart Scene appears with its name displayed. c. Press Save. Press to return to the main Smart Scenes menu. 32 7. Select Scheduled. a. Select the type of user who can run the Smart Scene. b. Select Scheduled to display clock and calendar settings. c. Set a time when the Smart Scene will start. Be sure to specify AM or PM. You can select Sunrise or Sunset instead of setting a time on the clock. Selecting Sunrise or Sunset overrides the clock controls. NOTE that updated Sunrise and Sunset times may depend on the systems connection to the internet or cellular phone network. Ask your installer for more information. d. Set the days of the week for the Smart Scene to take place. e. Press Save. The schedule settings are displayed. f. Press New Action to define the response when the scheduled time occurs (see Step #8). g. Press to return to the Smart Scenes menu. 8. Select Triggered Action. These options appear:
Smart Scenes can be started by one or a combination of the following options:
Event Zone Type Restore Zone Type Trigger System Operation NOTE: Event Zone Type, Restore Zone Type and Trigger can be different kinds of conditions. For example, a given Smart Scene can be triggered by a Fire alarm OR by an Entry/Exit event. Smart Scenes can also be triggered by Trouble conditions
(Trouble as the Trigger in one of the systems zones). Device-related events (such as Light On, Light Off, Door Locked, Door Unlocked) set the button at right to Device. Choices depend on the devices installed in your system. a. Event Zone Type starts the Smart Scene in response to any event (Fault, Trouble or Alarm) in any protected Zone of a specific zone type. Select the desired option. Typical zone types include:
Entry/Exit (front and back doors) Perimeter (typically window sensors) Interior Follower (typically motion sensors) Day/Night (Usually assigned to sensitive areas where immediate notification of an entry is always wanted.) 24 Hour Silent (Emergency button) 24 Hour Audible (Emergency button) Silent Burglary (typically a sensor) Fire No Verification (smoke detector) Fire With Verification (smoke detector) Carbon Monoxide (CO detector) 33 NOTE: Your system may include Zones that do not offer every Zone Type response. b. Restore Zone Type starts the Smart Scene when any zone with the selected Zone Type returns to its normal state (such as a door closing). The options are the same as Event Zone Type options. NOTE: Event Zone Type and Restore Zone Type are separate settings. For example, a given Smart Scene can be triggered by a Fire Alarm (Fire No Verification as the Event Zone Type) OR by an open door closing (Entry/Exit as the Restore Zone Type). c. Trigger starts the Smart Scene in response to a Fault, Trouble or Alarm in a Any change in the state of a sensor triggers the Scene. particular zone or changes to connected devices. A note about triggering events:
Any change in the state of a security system zone is known as a Fault. Faults can include Trouble and Alarm conditions. Trouble can include low battery or loss of communication with the device. Alarm conditions include zone faults while the system is armed and fire/CO sensors. Fault, Trouble and Alarm conditions can be used to trigger a Smart Scene. Fault:
Trouble: Only Trouble conditions trigger the Scene Alarm:
Choosing one of these events sets the button at right to display Zone options. Smart Scenes can also be triggered by changes in connected devices such as lights and locks. These events include:
Light On Light Off Door Locked Door Unlocked Choosing one of these events sets the button at right to display Device options. d. Choose Zone or Device, depending on your selection of a Trigger above. Security Only Alarm conditions trigger the Scene. zone sensors or devices such as lights and locks are listed. e. Select the zone or device and Save. f. System Operation starts Smart Scenes in response to security-related events. Options include:
Arm Away Arm Home Disarm Any Burglary Alarm Bell Timeout (end of the programmed time for which an alarm sounds) Start of Entry Delay End of Exit Delay Any Fire Alarm g. Select New Action to define the response when the triggering event occurs. NOTE: The 24 Hour Silent Alarm or 24 Hour Auxiliary Alarm Zone types will not trigger the selected Smart Scene if the Any Burglary Alarm option is programmed. 9. New Action defines the response when the triggering event occurs. This includes users manually running Anytime Smart Scenes, the time of Scheduled Smart Scenes and the conditions for Triggered Smart Scenes. You can choose both Security and automation device responses. The Security choices are:
Arm the system in Away mode. Arm the system in Home mode. Disarm the system. a. After choosing a Security setting, press and then Save. b. If you choose to work with Devices, a list of the systems automation devices appears. 34 c. Select one or more devices and set the devices desired operation. (For example, set switches to on or off, or locks to locked or unlocked.) d. After adding a device and its desired operation to the Smart Scene, press Save. Other available devices are displayed again so that they can be added to the Smart Scene. NOTE: In most situations, specific Security and Device information is displayed by pressing the Down arrow. 10. Press Save. 11. Press to return to the Smart Scenes menu. Hold Hold allows Scheduled and Triggered Smart Scenes to be temporarily suspended. A Scheduled Smart Scene can be put on Hold before programmed operations take place. 1. Select a Scheduled or Triggered Smart Scene. 2. Press Hold. The button is highlighted, and programmed operation will not take place. To remove a Hold:
1. On the Smart Scenes menu, enter a user code with access to the desired Smart Scene. 2. Select the Smart Scene and un-highlight Hold. Programmed operation will resume. Run Smart Scenes can be manually started with the Run button. The Smart Scenes results are displayed when the programmed operations have been performed. NOTE:
The Run option can be used to check the outcomes of Scheduled Smart Scenes and Triggered Smart Scenes, regardless of programmed triggers. 1. Select the Smart Scene. 2. Press Run. The system performs the programmed operations and the results are displayed. Successful operations are displayed with device information and a check mark. Failed operations are displayed with an empty circle. Show (Review) Use the Show button to see the programmed details of a Smart Scene without running it. 1. Select the Smart Scene. 2. Press Show. The scenes category, authorized users and included devices are displayed. 35 36 Video Home > Video The Gateway can display live video from as many as eight Wi-Fi-connected cameras. NOTE: Gateway and its cameras must be on the same Wi-Fi network. IMPORTANT If the Gateway loses AC power, the Video function is disabled to minimize drain on the backup battery. If power is lost while you are watching Wi-Fi cameras on the Gateway, video display may continue briefly before being suspended. When power is restored, the Gateway looks for available cameras. See Video Recovery. Remember that interruption of AC power to your Wi-Fi cameras and your router can also affect the Video function, even if the Gateway has AC power. Viewing and Naming Cameras 1. Press Video on the Home screen. Video appears in windows or the cameras appear in a list. OR The system may scan for cameras; when the scan is complete, the camera list appears. From these screens, you can:
Press to return to the Home screen. View live video. Name cameras. Add cameras to the system. 2. Select one or more cameras (as many as four) in the list. When multiple cameras are available, you may select as many as four. Selected cameras are highlighted and the Display option appears. You can also press Scan to search for other available cameras. Press a cameras name again to de-select it. 3. Select Display to see video from the selected camera(s). Select Camera List to return to the list view. With multiple cameras displayed, you can select one to work with by tapping its video window. 4. Viewing a single camera displays its details, which vary with the camera selected. For all compatible cameras, you can:
Name the camera. Select Name above the video display or Edit at right. Press Save on the on-screen keyboard. Press Press to show the camera full-screen. to return to the detail view. Some cameras offer additional options such as pan/tilt and built-in lighting. Adding a Camera Make sure that the camera is on the same Wi-Fi network as the Gateway system. Install the camera according to its instructions. With the camera installed:
1. View or list cameras as above. 2. Press Scan. The system looks for available cameras. 3. When the new camera is found, you can name it as described above. 37 Video Recovery Home > Security > Tools > Wi-Fi Config If video from remote cameras is lost or becomes distorted, the system can attempt to reset video streaming. By default, Gateway automatically begins to recover video about 60 seconds after Wi-Fi communication has been restored. The default setting is automatic video recovery. You may set recovery to begin only by user intervention (Manual Video Recovery). 1. Press Security on the Home screen. 2. Select Tools. Enter the Master Users security code. 3. Press WiFi Config. 4. Press Automatic Video Recovery repeatedly to choose between automatic and manual operation. 5. Press to return to the Tools menu. 38 Users and Security Codes Home > Security > Tools > Users Gateway uses 4-digit codes to restrict certain functions to selected users. A special 4-digit code can be set to trigger the systems Duress function. User codes can be used interchangeably when performing system functions (a system armed with one user's code can be disarmed by another user's code), with the exception of the Guest Code described below. All users are automatically assigned a user number, which cannot be changed. Do not confuse these user numbers with user codes. User Codes Master User This code is usually set when the system is installed, and can be User Guest changed later. Typically, the Master User is a household member who can perform all system functions. Only the Master User can add and remove users or modify their settings. Settings include assigning security codes and user names. Only the Master User can create Smart Scenes. Access to Smart Scenes for other users is controlled by the Master User. Typical users are household members and other authorized persons who can arm and disarm the security system, with controlled access to other system features. Visitors and others who are authorized to arm/disarm the system only at certain times or on a temporary basis. The Guests user code can be used to arm the system, but cannot disarm it unless the system was armed using the Guest code. The Guests user number is 47. Duress Code The Duress function requires connection to an alarm monitoring service. IMPORTANT Household members and authorized visitors can enter this code if forced to disarm or arm the system under threat. When the Duress code is entered, the Lyric Gateway and keypads appear to behave normally, but the system silently notifies your alarm monitoring service. The Duress Codes user number is 48. NOTES: A security code cannot be assigned more than once. If an existing code is entered, the system displays the warning User code not accepted! If this occurs, press OK to return to user settings and assign a different code. The system should be disarmed before you work with user codes. Limited-access users such as guests and cleaning staff should not be instructed on system functions other than those they will be using. The number of user codes supported by a Z-Wave door lock can vary between manufacturers. To ensure compatibility with Gateway, set the length of the Master User code on the door lock to be greater than four digits (?). 39 Adding Users and Assigning Codes 1. On the Home screen, press Security. 2. Press Tools, and enter the Master User code. 3. Select Users. Existing Users are displayed, along with the Guest and Duress code listings. Four asterisks appear on each listing that has a security code already established. See User Settings for full details. 4. Create and change settings in the menu shown here (the details may vary):
a. Create User: Press Add New and a new user screen like the one pictured above appears. Set the details as desired. b. Define/Change Guest Settings: Press Guest and then Edit. c. Set/Change Duress Code: Press Duress and then Edit. Enter a 4-digit code. 5. Save after making settings. The list of user codes reappears. 6. Press to return to the Tools menu. Changing Security Codes or the Duress Code The Master User can change other users names and security codes as well as delete users from the system. 1. Access the Users screen as shown above. 2. Select one of the listed users. 3. At the bottom of the screen, press Edit. User details appear. Note that a users number in the system, seen at upper right in the user details, cannot be changed. Deleting a User The Master user can delete secondary users from the system. 1. Select one of the listed users. 2. At the bottom of the screen, press Delete. Gateway requests confirmation. 3. Press Yes. 40 User Settings User Name Newly-created users are given a default name. To customize a users name:
1. Press Name at upper left on the display. A keyboard appears. 2. Press Clear to delete the default name. 3. Enter the desired name, using as many as 10 characters. 4. Save. User details appear. 5. Press Save again. The list of users appears, displaying your changes. User Code Newly-created users have no security code. To assign a code:
1. Press User Code. A keypad appears. 2. Press Clear if you are changing an existing code. 3. Enter a four-digit code. 4. Press Done. User details appear. 5. Save. The list of users appears. Users and Z-Wave Lock Control NOTE:
Each user can be given the ability to disarm the system by entering their code to open a Z-
Wave lock. When creating or editing a User:
1. Set Z-Wave Lock Control to Yes. Z-Wave Unlocking Door appears. 2. Select Disarm. 3. Press Save. With this setting, entering a user code at any Z-Wave door lock in the system unlocks the door and disarms the security system. This option appears only if Z-Wave devices are connected. 41 42 System Settings Brightness/Volume Home > Settings Adjust voice and system sounds with the Volume slider. System sounds include zone alert chimes and countdown beeps. Adjust touchscreen brightness with the Brightness slider. NOTES: As the sliders move, the Controller previews changing volume and brightness levels. Voice annunciations are controlled by enabling or disabling Chimes. Wi-Fi Configuration Home > Security > Tools > Wi-Fi Config Manage your systems router here. Remember that the Gateway and all Wi-Fi cameras must be on the same network. To View or Join Available Wi-Fi Networks 1. On the Tools menu, press the Wi-Fi Config button. A list of Wi-Fi options appears. 2. Press Scan Access Points. A list of available networks is displayed. Use the up and down arrows to scroll through the list. Press to return to the previous screen. 3. Select the desired network and press Edit. The network information is displayed. If a password is required, press Key and enter the password. 4. Press Save. 5. Press JOIN. 6. Press to return to the previous screen. Manually Configure Access Point IMPORTANT The Security setting below must match the security protocol used by your network router. 1. On the list of Wi-Fi options, press Manual Config AP. The Wi-Fi enrollment menu appears. (Fields include Network Type, which cannot be changed.) 2. Press SSID Name. 3. Enter the networks name. 4. Press Save. 5. Press Security. 6. Choose the same security protocol as your router. Options include Open, wpa/wpa2 and WPA2. (WEP is not supported.) If a password is required, press Key, and enter the password. 7. 8. Press Join. A confirmation screen appears. 43 9. Press OK and Save. 10. Press to return to the previous screen. Join a WPS Network 1. On the Gateway, have the list of Wi-Fi options ready. Dont press any buttons yet. 2. Press the WPS button on the access point device or router. 3. On the list of Wi-Fi options, press WPS. The Controller / MyHome Gateway or TC 4. displays Please Stand by for WPS Operation. If the operation is successful, the Controller / MyHome Gateway or TC displays Device has been successfully added to the network. 5. Press OK. If the operation is not successful, the Controller / MyHome Gateway or TC displays Failed Operation. Device not added to the network. Press OK. Automatic/Manual Video Recovery If video from remote cameras is lost or becomes distorted, the system can attempt to reset video streaming. By default, Gateway automatically begins to recover video about 60 seconds after Wi-Fi communication has been restored. The default setting is automatic video recovery. You may set recovery to begin only by user intervention. On the list of Wi-Fi options, toggle between Automatic Video Recovery and Manual Video Recovery. Press to return to the Tools menu. Software Updates Home > Security > Tools > Advanced Lyric Gateway Software updates for the Gateway are published periodically. Some updates request user permission in an on-screen window. Press Accept, Yes or OK to install the update. Certain critical updates are installed automatically. After updates of this type, information about the update is displayed on-screen. You can see the current version of the Gateways software at Security > Tools > Advanced >
System Information. IMPORTANT After a new SiX series sensor or key fob is enrolled in your system, the new devices software should be updated. This ensures that you are using the most up-to-date version of the software. Sensor Firmware Normally, SiX Series sensors in your system are updated when the Gateways software is updated. To initiate sensor firmware update manually:
1. On the Advanced menu, press Update Sensor Firmware. 2. Press Start and follow the instructions on the screen. 3. Press Stop when the update is complete. 4. Press to return to the Advanced menu. Key Fob Firmware (Wireless Keys) 44 SiX Series wireless keys:
We recommend that you have the key fob handy so you can work with it as instructed during this procedure. 1. On the Advanced menu, press Update Keyfob Firmware. 2. Press Start and follow the instructions on the screen. 3. Press Stop when the update is complete. 4. Press to return to the Advanced menu. Other types of wireless key:
Ask your installer about updating your systems other wireless keys. Date / Time Home > Security > Tools > Date Time Gateways clock and calendar are normally updated via the Gateways network connections. Use these controls to set date and time manually. Dont forget to specify your time zone and Daylight Savings Time if necessary. Be sure to Save your changes. If Gateway is reconnected to the cellular phone network or the Internet, the clock and calendar are updated automatically. Events Home > Security > Tools > Events The Gateway keeps a log of system events such as:
Arm/Disarm Alarm, Trouble and Fault Changes in status of Z-Wave devices The system can save up to 6000 events. When the log is full, the oldest 2000 entries are deleted to make room for logging new events. Logs can be viewed at the MyHome Gateway App or TC or exported in a variety of file formats. See Event Log Codes for a list of logged events and how they are displayed. Viewing Events 1. On the Tools menu, press Events. The MyHome Gateway App Events screen lists all events, sorted chronologically. 2. Press All to select different sorting options (Alarm, Trouble, Bypass, Open or Close or Non-Security). 3. Select All on the list to return to the view of all events. Exporting Events 1. Display events as above and press Export Logs. 2. When prompted, connect a USB storage device. 3. Select a file format. A progress display appears. When export is complete, the previous screen appears. 4. Remove the USB storage device. Keypad Home > Security > Tools > Keypad This menu displays the MAC ID of mobile devices connected to Gateway via the Honeywell MyHome Gateway app. The MAC ID is listed here when the app is first configured for use with Gateway. To disconnect a device, touch its listing on the screen and press Delete. The Gateway MyHome Gateway App requests confirmation; press Yes to proceed. 45 Testing Your System NOTE: TESTING SHOULD BE PERFORMED WEEKLY. Before testing, the system should be disarmed and all protected doors and windows closed. The Home button should show green. No alarm messages are sent to your alarm monitoring company during these tests. Press Tools and enter the 4-digit Master User code. Press Advanced. Testing Sensors (Walk Test) Home > Security > Tools > Advanced > Walk Test Start by pressing Walk Test. The Gateways internal sounder loudly sounds and Walk Test Home to Quit appears. The Gateway then beeps every 30 seconds as a reminder that the system is in Test mode. Note that Walk Test mode automatically quits after 4 hours. Doors and Windows Open each protected door and window in turn and listen for three beeps from the Gateway. If programmed to do so, each zones voice descriptor is heard. Identification of protection points with problems should appear on the display MyHome Gateway App screen. Notifications of problem zones clear when the door or window is closed. Motion Sensors Walk in front of each sensor and listen for three beeps and/or voice descriptors. The devices identification should appear on the display when it is activated. The display clears when no motion is detected. NOTE: If wireless motion detectors are in use, there is a 3-minute delay between activations, which helps preserve battery life. Fire/Carbon Monoxide sensors Follow the manufacturers instructions to test these devices. When a device is activated, its identification should appear on the touch MyHome Gateway App screen. When testing smoke detectors, keep the Lyric Gateway in test mode for at least one minute (60 seconds) after testing the detector to avoid sending unwanted alarm messages to your central station monitoring company. IMPORTANT If there is a problem with any sensor (no confirming sounds, no display), notify your service company. When all sensors have been checked (and doors and windows closed), no zone identification numbers should be displayed. Finish by pressing Home and entering the Master User code. 46 Testing Communications Home > Security > Tools > Advanced > Comm. Test These tests check the systems cellular network and internet (Wi-Fi/Ethernet) connections. On the Advanced menu, press Comm. Test. The options may vary with the devices installed in your system. Select the desired option to test connectivity and/or send test messages to the Central Station. If the test is successful, the MyHome Gateway App screen displays Service OK or ACK Received. Details of the test may be shown. Test Ethernet Checks internet connectivity without sending test messages. Send Any Send Cellular Message Send Ethernet Message Sends test messages via all available connections. Sends test messages via cellular network. Sends test messages via internet. Finish by pressing to run a different test or by pressing Home. Enter the Master User code if prompted. Reboot Home > Security > Tools > Advanced > Reboot Press Reboot to restart the Gateway if required. The system requests confirmation (Are You Sure?). Press Yes to proceed. 47 Maintenance The Lyric Gateway is designed to require little maintenance. However, testing your system is strongly recommended, and regular cleaning is suggested. Test the system weekly. Test your system after any alarm occurs. Care and Cleaning See Testing Your System for more information. Do not slam sensor-protected doors or windows. Keep dust from accumulating on the Gateway and sensors, particularly motion sensors and smoke or carbon monoxide detectors. The Gateway and sensors should be cleaned carefully with a soft, dry cloth. Do not clean the components with water or any other liquids. Select Settings Press Clean. During the 15 second countdown, a soft, damp cloth can be used on the screen without affecting the controls. on the MyHome Gateway App screen. NOTE: When the security system is armed, system event notifications will cancel the cleaning mode and return the system to normal operation. When the system is disarmed, only certain notifications will cancel cleaning mode. Battery Replacement Home > Security > Tools > Advanced > Install Backup Battery IMPORTANT Replace the battery pack when the Security menu displays Low Battery with no zone number specified. Use only batteries recommended by the installer or the manufacturer. Disarm the system before changing the Controllers battery pack. Remember that you must enter the Master User code for access to the Tools menu. Gateway Controller 1. Select Advanced on the Tools menu. 2. Select Install Backup Battery. Gateway requests confirmation that you want to proceed. 3. Press Yes and leave the battery installation procedure screen open. 4. ***Need new Procedure *** Open the Controllers case. If wall mounted, hang it from the self-contained hook as shown below. Need New Graphics Remove the body of the Controller from its wall mount or remove the desk mount from the back of the Controller. 48 5. Unplug the battery and remove it as seen below. 6. Install the replacement battery; remember to replace the connector inside the battery compartment. 7. Depending on your choice of a standard- or high-capacity replacement battery, position the battery retainer clip as seen below. 8. Close the case and replace the screw shown in Step 4. 9. Return the Controller to its mounting location. 10. Press OK on the battery installation procedure screen. 11. The system confirms Battery successfully installed". 12. Press OK. The system returns to the Advanced menu. 13. Press to return to the previous screen(s). Need New Graphics Sensors Clear sensor low-battery warnings by entering a user code on the Controller. Follow the sensors battery replacement instructions. NOTES: For SiX series smoke sensors, remove the battery and wait for 2 minutes before installing the replacement battery. (?) For other SiX series sensors and wireless keys, remove the battery and wait about 10 seconds before installing the replacement battery. 49 Communication Module Replacement Home > Security > Tools > Advanced > Install Cellular Module Refer to the illustrations below and follow these steps to replace a communication module:
THEN Removing the Bezel Need New Graphics Installing the Communication Module 1. With the system not armed, select Tools on the Security menu. 2. Enter the 4-digit Master User code. 3. Select Advanced. 4. Select Install Cellular Module. Follow the on-screen instructions for changing the module. 5. Press OK on the screen in step 4. The system confirms installation. 6. Press OK. The system returns to the Advanced menu. 7. Reboot the Controller (see Reboot for details). 50 SYSTEM DISPLAY and Buttons Zone numbers, location and other information may be displayed with status indications. Failure and Trouble indications and panel Emergency buttons appear in red. Home Screen Security Smart Scenes Automation Notices Video Settings Control Panel Buttons Below Touchscreen Emergency Home Press and hold for on-screen options Press to return from other screens Police Fire On-screen Emergency Buttons Medical Local Alarm System Status and Security Alarm Fire Alarm CO Alarm Arm Away Arm Home Arm Custom Arm Night Home Disarm Bypassed Zone Restart Timer
(more Exit time) Trouble/Alert Details on Security menu Wi-Fi
(signal strength) Wi-Fi Loss AC Power Loss Low Battery No Battery 51 Automation Failure
(Z-Wave problem) Door Open Window Open Glass Break Fire or Heat Sensor Flood Sensor Features/Various Icons may appear in red or orange to indicate device status. Problems involving Z-Wave devices are indicated by the Automation icon appearing in gray on the Home screen. Clean Control Panel Tools Users Events Advanced Keypad Date/Time Reminders Voice Command Wi-Fi Config Slide Show Notices Message Automation Switches Thermostats Locks Garages Water Valves 52 WIRELESS KEYS Key Assignments Your wireless keys (key fobs) are set up by your installer. You might wish to write down each buttons preprogrammed function in the space below. NOTES: One or more buttons may have been programmed for Emergency function. To activate a button function, press and hold the button for 1-2 seconds. 5800 Series wireless key Button A: ___________________ Button B: ___________________ Button C: ___________________ Button D: ___________________ Button 1: ___________________ Button 2: ___________________ Button 3: ___________________ Button 4: ___________________ Button 8*: ___________________
(press and hold BOTH buttons to activate) SiX Series wireless key SiXFOB Wireless Key Status Indications Press and release any key for system status. Status is indicated by the LEDs at the top of the key fob. Green LEDs Red LEDs Sounder System Status Rapid Flash Alternating about 8-20 seconds, then ON for 3 seconds Off Chirp for confirmation Device Enrollment ON 2-3 seconds 2 Beeps System Armed (any mode) Off Off Slow Flash for 2-3 seconds 4 Beeps ON 2-3 seconds Slow Flash for 2-3 seconds Flash once (both LEDs) Off Rapid Flash for 2 seconds Off Off Off Off Off 1 Beep Silent Silent 1 Second beep Silent 53 Alarm in progress or system in Audible Panic Mode Disarmed, Ready to Arm Disarmed, Not Ready to Arm RF Transmission Not Hearing from Controller Deleting wireless key from system Event Log Codes The Gateways Event Log can record and display as many as 6000 system events. Events are stored locally in the Gateway, in chronological order and sent to your monitoring company as needed. When the maximum number of stored events is reached, the oldest 2000 entries are deleted to make room for logging new events. The type of events that can be recorded is selectable; refer to the Gateway Installation and Reference Guides Programming section. The Events and CID Codes displayed vary with your systems options. The tables below provide definitions of the events/codes that may be transmitted to the Central Station and/or displayed by the MyHome Gateway App. Note: If the Gateways backup battery is exhausted after AC power is lost, any system activity occurring after Low Battery notification is not saved. Additionally, the Gateway will revert to the status condition as before the low battery notification. CID Code Definition Event Log Display Contact ID Event Log Codes 110 121 122 123 131 132 134 135 137 145 146 150 162 301 302 305 308 316 341 344 350 353 354 373 374 380 381 383 Alarm, Fire Alarm, Duress Alarm, Silent Alarm, Audible Alarm, Perimeter Alarm, Interior Alarm, Entry/Exit Alarm, Day/Night Alarm, Tamper Expansion Module Tamper Silent Burglary 24-Hour Non-Burglary Carbon Monoxide Detected Trouble, AC Loss Trouble, Low System Battery Trouble, System Reset System shutdown System Tamper*
Trouble, Case Tamper Trouble, RF Receiver Jam Detect Long Range Radio Reset Fire Duress Silent Audible Perimeter Interior Entry/Exit Day Night Tamper Expansion Module Tamper Silent Burglary 24 Hour Non-Burglary Carbon Monoxide Detected AC Loss Low system battery System Reset System shutdown System Tamper Cover Tamper RF Jam Detect Long Range Radio Reset Trouble, Long Range Radio Transmitter Fault Comm. Trouble Failure to Communicate Event Failure to Communicate Event Trouble, Fire Trouble Trouble, Exit Error Alarm Trouble, Sensor Trouble, Loss of Supervision RF Trouble, Sensor Tamper Fire trouble Exit error alarm Sensor trouble Superv Loss-RF Sensor Tamper Continued next page 54 384 401 403 406 407 408 441 455 459 461 570 601 602 606 607 623 627 628 654 655 RF Low Battery Open/Close by User Open/Close Automatic Cancel Remote Arm/Disarm Quick Arm Armed Home Auto-Arm Failed Recent Close Wrong Code Entry Zone/Sensor Bypass Manual Trigger Test Report Periodic Test Report Listen-in to follow Walk Test Event 90% Full Program Mode Entry Program Mode Exit System Inactivity Reset Master Code Contact ID Event Log Codes RF Low Battery Arm Away/Disarmed Automatic O/C (or Scheduled Arming) Cancel Remote Arm/Disarm Quick arm Arm Home/Disarmed Auto-arm Failed Recent Closing Wrong Code Entry Zone Bypass Manual Trigger Test Report Periodic test report Listen-in to follow Walk Test Mode Event Log 90% Full Program mode entry Program mode exit System Inactivity User Code
*If APL is enabled, AlarmNet 360TM will generate a special comm. fail message (E316) if it does not hear from a unit within 15 minutes after a delayed alarm is delivered. This message is meant to alert the Central Station that the system has been tampered with and may have been compromised. Central Station Messages The following messages are sent by the controller internal cellular or WiFi devices for the conditions listed below. Alarm Condition Power On / Reset Primary Communication Path Supervision Secondary Communication Path Supervision Test Alarm Code E33900950 E350C0951 E350C0952 555555559 Restore Code R350C0951 R350C0952 55 Glossary Zone Disarm Arm Away Arm Home Arm Custom Quick Arm Quick Exit Bypass Specific areas of protection in your home. Sensing devices are assigned to these numbered Zones, with designations such as front door, kitchen window, etc. Zone numbers appear on the display when an alarm or fault occurs. Turns off the security portion of the system. Silences alarms and trouble indicators. Enables all exterior and interior security protection provided by door and window sensors and motion detectors. Enables exterior protection; sounds an alarm if protected doors or windows are disturbed. Allows bypassing of selected zones, permitting movement within the home without unwanted alarms. Allows authorized users to arm the system with selected zones bypassed or with entry delays disabled. Allows household members to arm the system without entering a user code. This feature can only be enabled by an authorized user. Allows an outside door to be opened for a set time period. This feature is used for checking the mailbox, retrieving the newspaper, etc. Allows authorized users to exclude selected protection zones when arming the system. Emergency Special keys on the controller activate sounders on the premises and optionally send alert messages in various types of emergency. Connection to a central monitoring service is required for outside emergency calls. Special code that can be entered into the system instead of a normal user code. Sends a silent call for assistance while the Gateway appears to behave normally. Requires connection to a central monitoring service. The primary controller is the main device used to set up and control the Z-Wave network. There can only be one primary controller and it must be used to add/Include or delete/Exclude devices. A primary controller can be a portable device such as a hand-held remote, a permanently mounted control panel, a Z-
Wave enabled PC or a Z-Wave enabled Ethernet router/bridge. A secondary controller cannot be used to add or delete devices. If the secondary controller is the same model as the primary, it will have all of the primarys capabilities, but cannot be used to add or delete devices. Including a device pairs it with the Gateway so the two can communicate. In this document, the term Include is used interchangeably with Add. When a device is Excluded, it is removed from the system. Excluding the device also removes the network pairing from the devices memory. In this document, the term Exclude is used interchangeably with Delete. Important Note: A device must be Excluded before it can be moved to another network or re-
Included after a Gateway reset. 56 Duress Z-Wave Gateway Include Exclude Fire/CO Alarm System Your fire alarm system (if installed) is active 24 hours a day, providing continuous protection. In the event of an emergency, the installed smoke, heat and/or carbon monoxide detectors will automatically activate your security system, triggering a loud, intermittent tone from the touchscreen. The sound alternates with the voice announcement, sounding every 15 seconds. A FIRE or CO message will appear at your touchscreen and remain on until you silence and clear the alarm display. In Case of Fire 1. Should you become aware of a fire emergency before your detectors sense the problem, go to the Gateway and press the Emergency button and then select the Fire icon. The alarm will sound and an alarm will be transmitted to the central station (if programmed to do so). 2. Evacuate all occupants from the premises. 3. If flames and/or smoke are present, leave the premises and notify your local Fire Department immediately. If no flames or smoke are apparent, investigate the cause of the alarm. The zone number of the zone(s) in an alarm condition will appear on the touchscreen. 4. In Case of Carbon Monoxide Alarm 1. If a high level of carbon monoxide is detected you should evacuate all occupants from the premises and immediately move to a location where fresh air is available, preferably outdoors. 2. From a safe area, contact your central monitoring company for further instructions. Silencing a Fire/Carbon Monoxide Alarm 1. Silence the alarm by entering the Master User code. 2. To clear the alarm, enter the Master User code again. 3. If the touchscreen indicates a trouble condition after entering the Master User code a second time, check that smoke detectors are not responding to smoke- or heat-producing objects in their vicinity. Should this be the case, eliminate the source of heat or smoke. If this does not remedy the problem, there may still be smoke in the detector. Clear it by fanning the detector for about 30 seconds. 4. 5. When the problem has been corrected, clear the display by entering Master User code again. 57 National Fire Protection Association Smoke Detector Recommendations With regard to the number and placement of smoke and heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #72 noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household. The equipment should be installed as follows: A smoke detector installed outside of each separate sleeping area, in the immediate vicinity of the bedrooms and on each additional story of the family living unit, including basements and excluding crawl spaces and unfinished attics. In addition, the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages. 58 Emergency Evacuation Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protection Association:
1. Position your detector or your interior and/or exterior sounders so that they can be heard by all occupants. 2. Determine two means of escape from each room. One path of escape should lead to the door that permits normal exit from the building. The other should be an alternative escape, such as a window, should your path to that door be unpassable. Station an escape ladder at such windows if there is a long drop to the ground. 3. Sketch a floor plan of the building. Show windows, doors, stairs and rooftops that can be used to escape. Indicate escape routes for each room. Keep these routes free from obstruction and post copies of the escape routes in every room. 4. Assure that all bedroom doors are shut while you are asleep. This will prevent deadly smoke from entering while you escape. 5. Try the door. If the door is hot, check your alternate escape route. If the door is cool, open it cautiously. Be prepared to slam the door if smoke or heat rushes in. 6. When smoke is present, crawl on the ground. Do not walk upright, since smoke rises and may overcome you. Clearer air is near the floor. 7. Escape quickly; don't panic. 8. Establish a place outdoors, away from your house, where everyone can meet and then take steps to contact the authorities and account for those missing. Choose someone to assure that nobody returns to the house many die going back. 59 Regulatory Agency Statements FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
If using an indoor antenna, have a quality outdoor antenna installed. Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. RF EXPOSURE WARNING The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 in (20 cm) from all persons and must not be co-located or operated in conjunction with any other transmitter except in accordance with FCC multi-transmitter product procedures. Exposition aux Frequences Radio: L'antenne (s) utilise pour cet metteur doit tre installe une distance de sparation d'au moins 7,8 pouces (20 cm) de toutes les personnes. MISE EN GARDE IMPORTANT NOTE ABOUT EXTERNAL ANTENNAS If an external cellular radio antenna is used, the antenna may be installed or replaced ONLY by a professional installer. The external antenna must not exceed a maximum directional gain (including cable loss) of 3.2 dBi at 850 MHz and 2.3 dBi at 1900 MHz. TO THE INSTALLER 60 OWNER'S INSURANCE PREMIUM CREDIT REQUEST This form should be completed and forwarded to your homeowner's insurance carrier for possible premium credit. A. GENERAL INFORMATION:
Insured's Name and Address:
Insurance Company:
Lyric Gateway Policy No.:
Other ____________ Type of Alarm: Burglary Fire Both Installed by:
B. NOTIFIES (Insert B = Burglary, F = Fire) Local Sounding Device Name Name Serviced by:
Address Address Police Dept. Fire Dept. Central Station Name:
Address:
C. POWERED BY: A.C. with Rechargeable Power Supply Phone:
D. TESTING: Quarterly Monthly Weekly Other E. SMOKE DETECTOR LOCATIONS Furnace Room Kitchen Bedrooms Attic Basement Living Room Dining Room Hall F. BURGLARY DETECTING DEVICE LOCATIONS:
Front Door Basement Door Rear Door All Exterior Doors 1st Floor Windows All Windows Interior Locations All Accessible Openings, Including Skylights, Air Conditioners and Vents G. ADDITIONAL PERTINENT INFORMATION:
Signature:
Date:
61 62 Limitations of This Alarm System WARNING!
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:
Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death. Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90 to 105F, the detection performance can decrease. Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. Communication paths needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Communication paths are also subject to compromise by sophisticated intruders. Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments. 63 Your System Information Your local Honeywell dealer is the person best qualified to service your alarm system. Arranging a program of regular service is advisable. Security Company/Installer:
Name:
Address:
Phone:
DELAY DURATIONS AND ARMING OPTIONS Exit Delay time Entry Delay time 1 Entry Delay time 2 NIGHT HOME enabled zones QUICK ARM enabled?
Yes SYSTEM USERS No Keep track of authorized system users in the chart below. This record should be kept secure by the Master User. User #
Comment/Description User Code 02
(preset) Master User 47
(preset) Guest 48
(preset) Duress 03 04 05 06 07 08 09 10 11 12 13 14 Can add and modify Users. Can add, modify, edit and run all Smart Scenes. The Guest user code can be used to arm the system, but cannot disarm it unless the system was armed using the Guest code. Enter this code if forced to disarm/arm the system under threat. System appears to behave normally, but silently notifies alarm monitoring service. 64 Name SMART SCENES Voice Command assigned?
Description 65 Type Name Location Z-Wave Devices 66 TWO YEAR LIMITED WARRANTY Honeywell International Inc., acting through its Security & Communications business (Seller), 2 Corporate Center Drive, Melville, New York 11747 warrants its products to be free from defects in materials and workmanship under normal use and service, normal wear and tear excepted, for 24 months from the manufacture date code; provided, however, that in the event the Buyer presents a proper invoice relating to the purchased product and such invoice bears a date later than the manufacture date, then Seller may at its discretion, reflect the warranty period as commencing at invoice date. Except as required by law, this Limited Warranty is only made to Buyer and may not be transferred to any third party. During the applicable warranty period, Seller will repair or replace, at its sole option and as the exclusive remedy hereunder, free of charge, any defective products. Seller shall have no obligation under this Limited Warranty or otherwise if the product:
(i) is improperly installed, applied or maintained;
(ii) installed outside of stated operating parameters, altered or improperly serviced or repaired by anyone other than the Seller/Sellers Authorized Service/Repair Center;
(iii) damage is caused by outside natural occurrences, such as lightning, power surges, fire, floods, acts of nature, or the like; or
(iv) defects result from unauthorized modification, misuse, vandalism, alterations of serial numbers, other causes unrelated to defective materials or workmanship, or failures related to batteries of any type used in connection with the products sold hereunder. Exceptions to Warranty With Respect to Honeywell Products listed below:
Hardwire Contacts and PIRs Seller warrants parts for hardwire contacts and PIRs in accordance with the terms of the above limited warranty for a period of five (5) years from the manufacture date code. EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. TO THE FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY (i) CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES ARISING OUT OF OR RELATING IN ANY WAY TO THE PRODUCT AND/OR FOR BREACH OF THIS OR ANY OTHER WARRANTY OR CONDITION, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY SELLERS OWN NEGLIGENCE OR FAULT AND EVEN IF SELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES OR DAMAGES. Any product description (whether in writing or made orally by Seller or Sellers agents), specifications, samples, models, bulletin, drawings, diagrams, engineering sheets or similar materials used in connection with the Buyers order are for the sole purpose of identifying the Sellers products and shall not be construed as an express warranty or condition. Any suggestions by Seller or Sellers agents regarding use, applications, or suitability of the products shall not be construed as an express warranty or condition unless confirmed to be such in writing by Seller. Seller does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise, or that the products will in all cases provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery or fire without warning, but it is not insurance or a guarantee that such will not occur or will not cause or lead to personal injury or property loss. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM THE PRODUCT FAILED TO GIVE WARNING. However, if Seller is held liable whether directly or indirectly for any loss or damage with respect to the products it sells, regardless of cause or origin, its maximum liability shall not in any case exceed the purchase price of the product, which shall be fixed as liquidated damages and not as a penalty, and shall be the complete and exclusive remedy against the Seller. Should your product become defective during the warranty, please contact your installer to facilitate repair or replacement with Seller pursuant to the terms hereof. Seller reserves the right to replace any defective product under warranty with new, refurbished, or remanufactured product. For patent information, see www.honeywell.com/patents 67 Ref: LCP300-L/LCP300-LC 800-21670 800-21670 10/16 Rev A 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Copyright 2016 Honeywell International Inc. www.honeywell.com/security
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2016-09-29 | 908.42 ~ 908.42 | DXT - Part 15 Low Power Transceiver, Rx Verified | Original Equipment |
2 | 2412 ~ 2462 | DTS - Digital Transmission System | ||
3 | 344.94 ~ 344.94 | DSC - Part 15 Security/Remote Control Transmitter |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 3 | Effective |
2016-09-29
|
||||
1 2 3 | Applicant's complete, legal business name |
Ademco Inc.
|
||||
1 2 3 | FCC Registration Number (FRN) |
0004071130
|
||||
1 2 3 | Physical Address |
2 Corporate Center Drive
|
||||
1 2 3 |
9040
|
|||||
1 2 3 |
Melville, New York 11747
|
|||||
1 2 3 |
United States
|
|||||
app s | TCB Information | |||||
1 2 3 | TCB Application Email Address |
h******@acbcert.com
|
||||
1 2 3 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
1 2 3 |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
|||||
app s | FCC ID | |||||
1 2 3 | Grantee Code |
CFS
|
||||
1 2 3 | Equipment Product Code |
8DLGW
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 3 | Name |
M**** A******
|
||||
1 2 3 | Title |
RF Compliance Engineer
|
||||
1 2 3 | Telephone Number |
516-5********
|
||||
1 2 3 | Fax Number |
516-5********
|
||||
1 2 3 |
m******@honeywell.com
|
|||||
app s | Technical Contact | |||||
1 2 3 | Firm Name |
Honeywell International Inc.
|
||||
1 2 3 |
Honeywell International Inc
|
|||||
1 2 3 | Name |
E****** O******
|
||||
1 2 3 | Physical Address |
2 Corporate Center Drive
|
||||
1 2 3 |
Melville, 11747
|
|||||
1 2 3 |
United States
|
|||||
1 2 3 | Telephone Number |
516.5********
|
||||
1 2 3 | Fax Number |
516.5********
|
||||
1 2 3 |
E******@Honeywell.com
|
|||||
app s | Non Technical Contact | |||||
1 2 3 | Firm Name |
Honeywell International Inc.
|
||||
1 2 3 |
Honeywell International Inc
|
|||||
1 2 3 | Name |
A**** R********
|
||||
1 2 3 | Physical Address |
2 Corporate Center Drive
|
||||
1 2 3 |
Melville, 11747
|
|||||
1 2 3 |
United States
|
|||||
1 2 3 | Telephone Number |
516.5********
|
||||
1 2 3 |
316.5********
|
|||||
1 2 3 | Fax Number |
516.5********
|
||||
1 2 3 |
A******@Honeywell.com
|
|||||
app s | Confidentiality (long or short term) | |||||
1 2 3 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 3 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 3 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 03/28/2017 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 3 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 3 | Equipment Class | DXT - Part 15 Low Power Transceiver, Rx Verified | ||||
1 2 3 | DTS - Digital Transmission System | |||||
1 2 3 | DSC - Part 15 Security/Remote Control Transmitter | |||||
1 2 3 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Harmony Gateway | ||||
1 2 3 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 3 | Modular Equipment Type | Does not apply | ||||
1 2 3 | Purpose / Application is for | Original Equipment | ||||
1 2 3 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 3 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 3 | Grant Comments | Power Output is Conducted. This filing meets KDB 447498 as a mobile device. Grantee must provide installation and operating instructions for complying with FCC multitransmitter product procedures. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. | ||||
1 2 3 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 3 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 3 | Firm Name |
Honeywell International Inc.
|
||||
1 2 3 |
Rhein Tech Laboratories, Inc.
|
|||||
1 2 3 | Name |
M**** S****
|
||||
1 2 3 |
R******** M******
|
|||||
1 2 3 | Telephone Number |
516-5********
|
||||
1 2 3 |
703-6********
|
|||||
1 2 3 | Fax Number |
516-5********
|
||||
1 2 3 |
703-6********
|
|||||
1 2 3 |
m******@honeywell.com
|
|||||
1 2 3 |
r******@rheintech.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CC | 908.42000000 | 908.42000000 | ||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15C | CC | 2405 | 2475 | 0.077 | |||||||||||||||||||||||||||||||||||
2 | 2 | 15C | CC | 2412 | 2462 | 0.012 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
3 | 1 | 15.231 | CC | 344.94000000 | 344.94000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC