all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
Quick Install Guide | Users Manual | 611.96 KiB | / October 10 2014 | |||
1 2 |
|
Users Manual Rev B | Users Manual | 807.70 KiB | / October 10 2014 | |||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | External Photos | / October 10 2014 | ||||||
1 2 | Internal Photos | / October 10 2014 | ||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Test Setup Photos | / October 10 2014 | ||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | November 04 2014 | ||||||
1 2 | Test Report | November 04 2014 | ||||||
1 2 | Test Report | November 04 2014 | ||||||
1 2 | Test Report | November 04 2014 |
1 2 | Quick Install Guide | Users Manual | 611.96 KiB | / October 10 2014 |
EXHIBIT 7B CFS8DLTSSCBASE / 573F-TSSCBASE TSSC Installation and Setup Guide STEP 1 - Installing the Base (TSSBU111011U) Rechargeable Backup Battery and Power Connector 1. Remove the Base Case Back. 2. Connect the battery connector to the receptacle on the PC board. 3. Insert the Battery Pack into the case. 4. Secure the Battery Pack with the Battery Retainer using the Retaining Screw. 5. Connect the power pack into the power receptacle, looping the power cord as shown in Detail A. NOTE: If using the optional wall mount configuration, skip to the Base wall mounting procedure. If not, complete step 6. 6. Secure the Case Back onto the Base. NOTE: Do not apply power at this time. ENGAGE HOOKS AND SLIDE DOWN
(4) WALL MOUNTING PLATE BATTERY PACK WALL SURFACE CASE BACK DETAIL A REAR OF BASE UNIT SECURE CASE BACK USING MOUNTING SCREWS (TYP - 4 PLACES) TAMPER SCREW tssc-015-V0 STEP 2 - Setting up the Communication Links Prior to power up of the Base (when directed in the TSSC Installer App), the Ethernet communications link must be connected to the residences router. The connection is from an Ethernet port on the router to the ETH0 port on the Base. IMPORTANT! Under no circumstances should the ETH1 port ever be connected to the residences router. ETH1 ETH0 TO POWER RECEPTACLE FOR INSTALLER USE ONLY TO/FROM RESIDENCE ROUTER ETHERNET PORT BASE UNIT RETAINING SCREW BATTERY RETAINER BATTERY PACK BASE UNIT STEP 3 - Keypad (TSSKP112011U) Mounting The keypad is designed to be placed on a desk/table top with the stand attached. An optional mounting plate can be used to mount the keypad to the wall. tssc-021-V0 tssc-016-V0 Mounting the Base to a Wall (Optional) To mount the Base to a wall, perform to the following:
IMPORTANT: Record the ACTIVATION KEY number, MAC Address, CRC number and WPA2 number located on case back prior to wall mounting. 1. Complete steps 1 through 5 of the Installing the Base Rechargeable Backup Battery and Power Connector paragraph 2. Secure the Mounting Plate to the wall and secure with 4 screws. 3. Install the Tamper Screw as shown. 4. Secure the Base to the Mounting Plate by aligning the slots on the Base and sliding the unit down until locked in position. 800-13956V1o 800-13956V1 11/13 Rev. A Power Connections Connect the Power Supply Cable into its connector as shown below and route it from the bottom of the keypad. IMPORTANT: Do not apply power to the keypad at this time. Installing Keypad To Desk-Top Stand 1. Place the Keypad face down on a level surface. 2. Connect the battery connector to the receptacle on the PC board. 3. Insert the Battery Pack into the case. 4. Secure the Battery Pack with the Battery Retainer using the Retaining Screw. 5. Install tabs on Desk Stand into appropriate slots as shown and secure with two screws 6. Plug in the power pack to the receptacle. 1 SLOT
(TYP) KEYPAD DESK STAND SLIDE TABS UP INTO SLOTS BATTERY PACK POWER SUPPLY CABLE SECURE WITH SCREWS (2)
(TYP) tssc-011-V1 STEP 4 - Base Registration and Accessing The Installer App Run TSSC Installer App:
Go to https://portal-test.adtpulse.com/activation and follow the prompts. Powering the Base When directed in the TSSC Installer App, plug the power pack into the wall receptacle to power the Base. During the first 45 seconds of power initialization, TSSC lights up the CELLULAR, NETWORK and STATUS LEDs one by one slowly in sequence. After the first 45 seconds, the LEDs chase in a rapid sequence for approximately 30 more seconds. The POWER LED is always ON while initialization is being executed. When the LEDs stop chasing and the POWER LED is lit green, the Base is powered up and ready for the registration process to begin. NOTE: The BATTERY LED will blink until the battery is fully charged. NOTE: The NETWORK LED will remain amber until activated. Radio Activation Go to https://portal-test.adtpulse.com/activation and follow the prompts. Contacting Technical Support PLEASE, before you call Technical Support, be sure you:
READ THE INSTRUCTIONS!
Determine that the power supply and/or backup battery are supplying proper voltages. Verify your programming information where applicable. Note the proper model number of this product, and the version level (if known) along with any documentation that came with the product. Note your ADT customer number and/or company name. Having this information handy will make it easier for us to serve you quickly and effectively. Technical Support: Contact your ADT Customer Care Representative. THE LIMITATIONS OF THIS ALARM SYSTEM While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:
Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second-floor detector, for example, may not sense a first-floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90 to 105F, the detection performance can decrease. Alarm warning devices such as sirens, bells, or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. Recommendations For Proper Protection The Following Recommendations for the Location of Fire and Burglary Detection Devices Help Provide Proper Coverage for the Protected Premises. Recommendations for Smoke and Heat Detectors With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #72 noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: For minimum protection a smoke detector should be installed outside of each separate sleeping area, and on each additional floor of a multi-floor family living unit, including basements. The installation of smoke detectors in kitchens, attics (finished or unfinished), or in garages is not normally recommended. For additional protection the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages. In addition, we recommend the following:
Install a smoke detector inside every bedroom where a smoker sleeps. Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the sleeper if the door is closed. Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air conditioners or humidifiers) are used. Install smoke detectors at both ends if the hallway is more than 40 feet (12 meters) long. Install smoke detectors in any room where an alarm control is located, or in any room where alarm control connections to an AC source or phone lines are made. If detectors are not so located, a fire within the room could prevent the control from reporting a fire or an intrusion. FEDERAL COMMUNICATIONS COMMISSION STATEMENTS Regulatory Agency Statements The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different If using an indoor antenna, have a quality outdoor antenna installed. branch circuits. Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. FCC / IC STATEMENT This Control Complies With NFPA Requirements For Temporal Pulse Sounding Of Fire Notification Appliances Recommendations for Proper Intrusion Protection For proper intrusion coverage, sensors should be located at every possible point of entry to a home or premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system. This will ensure that alarm signals can be sent to the alarm monitoring station in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines, if connected to an alarm monitoring station). Specifications Base Unit:
Physical:
Dimensions:
Electrical:
Voltage Input:
24-Hour Backup Battery:
8.5 W x 6 H x 1.875 D P/N 300-05763V1: 110 VAC input/9 VDC output 2.5A, 2-prong P/N TSSBU111061U: Rechargeable Backup Battery: Nickel-metal hydride battery pack rated at 7.2 Vdc, 3700mA Communication:
Formats Supported:
4-Digit Contact ID Keypad:
Physical:
Dimensions:
Electrical:
Voltage Input:
6.69 W x 5.36 H x 0.875 D P/N 300-05763V1: 110 VAC input/9 VDC output 2.5A, 2-prong 24-Hour Backup Battery:
P/N TSSKP112061U: Rechargeable Backup Battery: 7.2V, 6xAAA, 6x600mAH, NiMH WARRANTY INFORMATION For the latest warranty information, please visit:
www.honeywell.com/security/hsc/resources/wa Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners, and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments. This device complies with Part 15 of the FCC Rules, and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles.
(2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. ADT Security Services, Inc. 1501 Yamato Road Boca Raton, FL 33431 Copyright 2013 ADT Security Services 2
1 2 | Users Manual Rev B | Users Manual | 807.70 KiB | / October 10 2014 |
EXHIBIT 7A B CFS8DLTSSCBASE / 573F-TSSCBASE TSSBU111011U Base Control Unit and TSSKP112011U Wireless Bidirectional Alpha Keypad User Guide BASE FEATURES Display The TSSBU111011U (Base) is a wireless Control Unit that allows you to perform system arming and disarming functions, as well as to monitor the status of your security system. TSSBU111011U w/Protective Door Removed LEDs LED Off Red Amber Green Flashing Green Flashing Amber Flashing Red Alternating Flashing No AC POWER BATTERY
(see note 1) STATUS Not Ready Low Battery/
Missing Battery Armed NETWORK
(see note 2) Not Configured No Ethernet Link CELLULAR Not Configured No Connection or Bad Signal Charging AC Battery -
Normal System Trouble Ready Link but Not Connected to Alarm Receiver Ethernet Link Good Signal Device Trouble Can Arm Device Trouble Cannot Arm Alarm/Alarm Memory Cell but No Data SIM Error In Programming
- Red In Programming
- Off In Programming
- Green In Programming
- Off NOTE 1: During Sleep Mode only the BATTERY LED is active. NOTE 2: This LED may remain in the Amber state for up to 24 Hours until a report is sent and acknowledged by the central station. KEYPAD FEATURES Display The TSSKP112011U (Keypad) is a wireless Keypad that allows you to perform your security system functions, as well as to display the status of your security system. LEDs LED POWER TSSKP112011U w/ Protective Door Removed Off Red Amber Green Charging AC Low Battery 5%/Missing Battery
(when no AC)
(Keypad's battery) Flashing Amber Flashing Green On Battery Normal
(no AC) Alternating Flashing In Programming
- Red Flashing Red Low Battery 20% (no AC)
(Keypad's battery) TROUBLE STATUS In Programming, No Trouble Not Ready Armed System Trouble Ready to Arm Device Trouble NOTE: During Battery Mode only the POWER LED is active. Alarm/Alarm Memory In Programming
- Green 2 KEYS Access the Base control keys by lifting up the door. The Keypad keys are continuously backlit for ease of use. Access the Keypad keys by opening the swing-down door. The Keypad keys are continuously backlit for ease of use. KEY OFF AWAY STAY M AX TEST BYPASS I NSTANT CODE CH I M E READY
[#]
Numeric keys 0-9 Special function keys DESCRIPTION Disarms the burglary portion of the system, silences alarms and audible trouble indicators, and clears visual alarm trouble after the problem has been corrected. Completely arms both perimeter and interior burglary protection by sensing an intruder's movements through protected interior areas as well as guarding protected doors, windows, etc. Late arrivals can enter through an entry delay zone (entrance door) without causing an alarm if the system is disarmed before the entry delay time expires. Arms the perimeter burglary protection, guarding protected doors, windows and other perimeter protection points, and sounds an alarm if one is opened. Also allows automatic bypassing of certain areas which permits movement within your house without causing an alarm. Late arrivals can enter through an entry delay zone (entrance door) without causing an alarm if the system is disarmed before the entry delay time expires. Arms in manner similar to AWAY mode, but eliminates the entry delay period, thus providing maximum protection. An alarm will occur immediately upon opening any protection point, including entry delay zones (entrance doors).
(Keypad only) - Tests the system and alarm sounder if disarmed.
(Keypad only) - Removes individual protection zones from being monitored by the system. Displays previously bypassed protection zones. Arms in manner similar to STAY mode, but turns off the entry delay period, offering greater security while inside and not expecting any late arrivals. An alarm will occur immediately upon opening any perimeter protection point, including entry delay zones.
(Keypad only) - Allows the entry of additional user codes that can be given to other users of the system.
(Keypad only) - Turns on and off the CHI ME mode. When on, any entry through a protected delay or perimeter zone while the system is disarmed will cause a tone to sound at the K eypad(s).
(Keypad only) - When depressed prior to arming the system, the Keypad will display all open protection zones within the Keypad's home partition. This key is also used to display all zone descriptors that have been programmed for your system, by holding the key down for at least 5 seconds.
(Keypad only) - Permits ARMING of the system without use of a security code ("Quick Arm", if programmed). Used to enter your individual security access code(s). Panic alarm activation (Keypad only). The panic alarms are activated by pressing a Special Function Key (see below). Panic key functionality and the type of panic alarms produced, is determined by the control panels capability and programming. (Check with your installer for the availability and assignment of these panic keys.) SPECIAL FUNCTION KEYS (KEYPAD ONLY) The A, B, and C keys located to the left of the numeric keys can be programmed as Panic Alarm Activation keys. (Check with your installer for the availability and assignment of these panic keys.) Key Function A B C 3 GENERAL OPERATION To make sure the latest system status is displayed, press the [*] key before and after entering each command. HOW TO GET SYSTEM STATUS The display continuously displays the present security system status. When there is a change in system status (such as going from an ARMED STAY to DISARMED), it may take up to 20 seconds for the display to automatically update the status to show the status change. However, you can press the [*] key to update the display immediately. ARMING THE SYSTEM To arm the system in the AWAY, STAY, INSTANT or MAX mode, enter your user code and press the numeric key above the selected mode. DISARMING THE SYSTEM To disarm the system enter your user code + OFF key [1]. BYPASSING ZONES To bypass an individual zone, enter your user code + BYPASS key [6] + faulted zone number of the zone to be bypassed. To bypass multiple zones, enter the command string (user code + BYPASS key [6]) then sequentially enter the 3-digit zone numbers of the zones to be bypassed, up to five zones in each command. Multiple Zone Bypass Example: user code + BYPASS [6] + 003 004 005 007 009. If you want to bypass all faulted zones (Forced Bypass), enter your user code + BYPASS key [6] + [#] + [0]. The Forced Bypass feature must be enabled by your installer: [ ] yes [ ] no USER CODES To Add a User I M PORTANT: Temporary users should not be shown how to use any system function they do not need to know (e.g. bypassing protection zones). Enter Master code + CODE key [8] + 2-two digit user no. + 4-digit new users code. User numbers 02 through 96 are available with various authority levels. Note that User no. 01 is used for the Master code AUTH ORI TY LEVEL:
Enter Master code + CODE key [8] + 2-digit user no. + [#] + [1] + single-digit authority level. For authority levels, see definitions below. Level N/A 0 Title Master Standard User 1 2 3 Arm Only Guest Duress Code Explanation Reserved for user 01; Can perform all system functions and assign codes. Can only perform security functions. Cannot perform system functions reserved for the master user. Can only arm the system. Cannot disarm or do other functions Can arm the system and bypass zones, but cannot disarm the system unless the system was armed with this code. This code is typically assigned to someone (e.g., babysitter or cleaner) who has a need to arm/disarm the system only at certain times. Intended for use when you are forced to disarm or arm the system under threat. When used, the system will act normally, but can silently notify the Central Monitoring Station of your situation, if that service has been provided. To Change a User's Code Changing the Master code Enter Current Master code + CODE key [8] + 01 + 4-digit new code + 4-digit new code again. Changing a User code Enter Master code + CODE key [8] + 2-two digit user no. + 4-digit new users code. To Delete a User Enter Master code + CODE key [8] + 2-digit user code to be deleted + # + 0. A single confirmation tone will be heard and the code is no longer functional. 4 CHIME MODE Your system can be set to alert you to the opening of a door or window while it is disarmed by using CHI ME mode. When activated, three tones sound at the Keypad whenever a protected perimeter door or window is opened, and the Not Ready message is displayed. Pressing the READY [*] key displays the open protection points. Note that Chime mode can be activated only when the system is disarmed. 1. To turn Chime M ode on, enter the security code and press the CH I M E key [9]. 2. To turn Chime M ode off, enter the security code and press the CH I M E key again. KEYPAD TONES When the Keypad is generating a periodic beep (once per minute), pressing the [*] key provides more information. When the system is armed and there is a trouble condition, the Keypad displays Device Trouble. Pressing the [*] key provides more information. QUICK EXIT To start Quick Exit when enabled. Stay Mode Enter User code + STAY key. Instant Mode Enter User code + INSTANT key Night-Stay Mode With the system armed in Night-Stay Mode and the exit delay expired, enter User code + STAY key + STAY key. HOST CHECK-IN If Host Check-In interval is set to 200 seconds, Download Com/Upload Completed message is displayed at the Keypad every 200 seconds. TEST MODE Use Test mode to check each protection point for proper operation. Testing should be conducted weekly to ensure proper operation. 1. Disarm the system and close all protected windows, doors, etc. 2. Enter the Master code + [5] (TEST), then press 1. 3. Listen. The external sounder should sound for about 1 second then turn off. 4. Fault all zones in turn and listen for three beeps from the keypad. ID of each faulted point should appear on the keypad display. The display clears when the zone is closed. Note that if wireless motion detectors are used, there is a 3-minute delay between activations. This conserves battery life. 5. Test all smoke and CO detectors following the manufacturer's instructions and check the display. 6. When all zones have been checked and are intact (closed), there should be no zone identification numbers displayed on the keypad. 7. Exit test mode: security code + [1] (OFF). NOTES:
The keypad sounds a single beep about every 60 seconds as a reminder that the system is in the Test mode. Alarm messages are not sent to your Central Station while Test mode is on. If a problem is experienced with any protection point (no confirming sounds, no display), call for service immediately. If the test mode is inadvertently left active, it automatically turns off after 30 minutes. During the final five minutes, the keypad will emit a double beep every 30 seconds. 5 REPLACING THE BATTERY IN A WALL MOUNTED KEYPAD 1. Remove the retaining screw at the bottom of the Keypad. 2. Press upward with your thumbs on the bottom edge of the Keypad housing and slide the Keypad up with respect to the wall mounting plate, removing the Keypad from the wall mounting plate. 3. Remove the power harness on the old battery pack that connects to the printed circuit board. 4. Lift the old battery pack from the Keypad and replace with the new battery pack. 5. Connect the power harness to the printed circuit board. 6. Replace the Keypad onto the wall mounting plate and secure with the retaining screw. NOTE: After replacing the battery and reattaching the Keypad to the mounting plate, enter the 4-digit security code + OFF sequence twice to clear any trouble condition. REPLACING THE BATTERY IN A DESK MOUNTED KEYPAD 1. Place the Keypad face down on a level surface. 2. Remove two screws and lift up Desk Stand up and away from the Keypad to expose the battery pack. 3. Remove the power harness on the old battery pack that connects to the printed circuit board. 4. Lift the old battery pack from the Keypad and replace with the new battery pack. 5. Connect the power harness to the printed circuit board. 6. Place the tabs on the Desk Stand into the appropriate slots and secure with two screws. NOTE: After replacing the battery and reattaching the Keypad to the mounting plate, enter the 4-digit security code + OFF sequence twice to clear any trouble condition. 6 THE LIMITATIONS OF THIS ALARM SYSTEM While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:
Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second-floor detector, for example, may not sense a first-floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90 to 105F, the detection performance can decrease. Alarm warning devices such as sirens, bells, or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners, and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments. FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS FOR TSSBU111011U FCC ID: CFS8DLTSSCBASE, IC: 573F-TSSCBASE, IC MODEL: TSSCBASE If using an indoor antenna, have a quality outdoor antenna installed. The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. Warning The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-
transmitter product procedures. Mise en Garde -- Exposition aux Frequences Radio: L'antenne (s) utilise pour cet metteur doit tre installe une distance de sparation d'au moins 7,8 pouces (20 cm) de toutes les personnes. RF Exposure 7 LIMITED WARRANTY Terms and Conditions Applying to Sale of Equipment Limited Warranty. 1. Any part of the system, including the wiring, installed under this Agreement which proves to be defective in material or workmanship within 90 days of the date of completion of installation will be repaired or replaced at ADT's option with a new functionally operative part. Labor and material required to repair or replace such defective components or to make mechanical adjustments to the system will be free of charge for a period of 90 days following the completion of the original installation. This warranty is extended only to the original consumer purchaser of the system and may be enforced only by such person. To obtain service under this warranty, call or write our local ADT Service Department at the telephone number or address found in your local yellow pages. Service pursuant to the warranty will be furnished only during ADT's normal working hours 8:00A.M. to 4:30P.M., Monday through Friday, except holidays. Services rendered outside the normal working hours of ADT are not within the scope of this warranty and any services requested to be performed at such times shall be charged for at ADT's then applicable rates for labor and material. This warranty does not apply to the conditions listed below, and in the event customer calls ADT for service under the warranty and upon inspection it is found that one of these conditions has led to the inoperability or apparent inoperability of the system, a charge will be made for the service call of the ADT representative, whether or not he actually works on the system. Should it actually be necessary to make repairs to the system due to one of the "conditions Not Covered By Warranty", a charge will be made for such work at ADT's then applicable rates for labor and material. Conditions Not Covered By Warranty. Damage from accidents, acts of God, alterations, misuse, tampering or abuse. B. Failure of the customer to properly close or secure a door, window, or other point protected by a burglar alarm device. C. Failure of customer to properly follow operating instructions provided by ADT at time of installation or at a later date. D. Trouble in leased telephone. E. Trouble due to interruption of commercial power. F. Battery replacements. This warranty is in lieu of all other express warranties. Any implied warranties of merchantability and fitness for a particular purpose are limited in duration to a period of 90 days from the date of completion of installation. The exclusive remedy of the customer hereunder shall be repair or replacement as stated above. Under no circumstances shall ADT be liable to the customer or any other person for incidental or consequential damages of any nature, including without limitation, damages for personal injury or damages to property, and, however occasioned, whether alleged as resulting from breach of warranty by ADT, the negligence of ADT, or otherwise, ADT's liability will in no event exceed the purchase price of the system. Some states may not allow limitations on how long an implied warranty lasts, or the exclusion or limitations of incidental or consequential damages, so the above limitations and exclusions may not apply to you, unless a longer period is required by applicable law. Any action against ADT in connection with a system must be commenced within one year after the cause of action has occurred. No agent, employee or representative of ADT or any other person is authorized to modify this warranty in any respect. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 2. ADT agrees to install the equipment in a workmanlike manner in accordance with the following conditions:
Customer will make premises available without interruption during ADT normal working hours 8:00A.M. to 4:30P.M., Monday through Friday, except Holidays. B. Customer understands that the installation will necessitate drilling into various parts of the premises: ADT intends, generally, to conceal wiring in the finished areas of the premises; however, there may be areas which, due to construction, decoration, or furnishing of the premises, ADT determines, in its sole discretion, that it would be impractical to conceal wiring and, in such cases, wiring will be exposed. C. Customer agrees to provide 110 VAC electrical outlets at designated locations for equipment requiring AC power. D. Customer to provide for lifting and replacing carpeting, if required, for installation of floor mats or wiring. Installation. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form, or by any means electronic, mechanical, photocopying, recording, or otherwise without the written permission of ADT Security Services. The material in this publication is for information purposes and subject to change without notice. ADT Security Services assumes no responsibility for any errors which may appear in this publication. ALL RIGHTS RESERVED ADT Security Services 1501 Yamato Rd Boca Raton, FL 33431 Copyright 2013 K0667D 800-13959 11/13 Rev. B
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2014-04-13 | 908.4 ~ 908.4 | DXT - Part 15 Low Power Transceiver, Rx Verified | Original Equipment |
2 | 344.94 ~ 344.94 | DSC - Part 15 Security/Remote Control Transmitter |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2014-04-13
|
||||
1 2 | Applicant's complete, legal business name |
Ademco Inc.
|
||||
1 2 | FCC Registration Number (FRN) |
0004071130
|
||||
1 2 | Physical Address |
2 Corporate Center Drive
|
||||
1 2 |
9040
|
|||||
1 2 |
Melville, New York 11747
|
|||||
1 2 |
United States
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
h******@acbcert.com
|
||||
1 2 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
CFS
|
||||
1 2 | Equipment Product Code |
8DLTSSCBASE
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
M**** A******
|
||||
1 2 | Title |
RF Compliance Engineer
|
||||
1 2 | Telephone Number |
516-5********
|
||||
1 2 | Fax Number |
516-5********
|
||||
1 2 |
m******@honeywell.com
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
Honeywell International Inc.
|
||||
1 2 | Name |
S****** A********
|
||||
1 2 | Physical Address |
2 Corporate Center Drive
|
||||
1 2 |
Melville, New York 11747
|
|||||
1 2 |
Melville, 11747
|
|||||
1 2 |
United States
|
|||||
1 2 | Telephone Number |
516 5********
|
||||
1 2 |
516 6********
|
|||||
1 2 | Fax Number |
516 5********
|
||||
1 2 |
516 6********
|
|||||
1 2 |
s******@honeywell.com
|
|||||
app s | Non Technical Contact | |||||
1 2 | Firm Name |
Honeywell International Inc.
|
||||
1 2 | Name |
M******** S******
|
||||
1 2 | Physical Address |
2 Corporate Center Drive
|
||||
1 2 |
Melville, New York 11747
|
|||||
1 2 |
Melville, 11747
|
|||||
1 2 |
United States
|
|||||
1 2 | Telephone Number |
516 5********
|
||||
1 2 | Fax Number |
516 5********
|
||||
1 2 |
m******@honeywell.com
|
|||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 10/10/2014 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DXT - Part 15 Low Power Transceiver, Rx Verified | ||||
1 2 | DSC - Part 15 Security/Remote Control Transmitter | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Security Base Control Unit | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | Yes | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Honeywell International Inc.
|
||||
1 2 | Name |
M**** S******
|
||||
1 2 | Telephone Number |
516-5********
|
||||
1 2 | Fax Number |
516-5********
|
||||
1 2 |
m******@honeywell.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CC | 908.40000000 | 908.40000000 | ||||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15.231 | CC | 344.94000000 | 344.94000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC