FCC ID: CFS8DL6SHKA Wireless Shock/Door/Window Sensor

SiXSHOCK Wireless Shock/Door/Window Sensor Installation Instructions The SiXSHOCK is a 3-zone wireless shock/door/window sensor is intended for use with Honeywell controls that support SiX series devices. It provides Reed switch/magnet zone External wired contact zone Built-in shock sensor zone Typical shock protection area:

10 - 12 sq. ft. / 5 - 6 foot radius (3.05m 3.66m /

1.52m 1.83m radius) The coverage area can vary depending on the mounting surface. Open the SiXSHOCK Firmly slide the top and bottom housings in opposite directions and pull them apart to open the device. Installation Options The SiXSHOCK can be mounted with several options:

Loop 1: Built-in shock sensor alarm status Loop 2: Normally closed, built in reed switch, used with the included magnet (1) Loop 3: Externally wired, closed-circuit contact loop connected to the Terminal Block NOTE:Wiring limit is 3ft. Gap specifications:

a. Make gap is at least 0.8" (1) b. Break gap is at least 0.95" (1)

(reduced about 30% for steel) Mounting TheSiXSHOCKsensor MUST be mounted as follows:

On swinging doors: mount on upper corner, opposite hinge is ideal On sliding windows and doors: on the frame

(on moving section when magnet is used) Double sided tape and screws provided for mounting. Signal Strength Guide Signal strength: Range of 1-4 bars (green); should be minimum 1 green bar for the Zone being programmed. Four red bars indicate poor signal strength; the device should be relocated. See the Controls instructions for bar indication signal strength values. Enroll and Set Up For the Lyric Controller NOTE: The SiXSHOCK can be enrolled and programmed before or after installation. 1. Set the Lyric Controller in Programming Mode:

Security > Tools > [installer code] > Program >

(scroll down) > SiX Programming. 2. Pull the battery tab to activate the SiXSHOCK. (Use the magnet if the battery tab is removed.) Signal Strength Good Description Four Green Bars Three Green Bars Two Green Bars One Green Bar Four Red Bars Relocate the device Icon 3. The LED flashes (up to about 20 seconds*) during enrollment. All services (Reed and Terminal Block) are enrolled in sequential (or next available) zone numbers. The device sends its unique MAC ID (Serial Number); the controller registers the device and displays the transmitter data on screen.

*NOTE: Enrollment time varies depending on the signal strength between the device and the controller. 4. When done, the LED is ON for 3 seconds and the control beeps to confirm enrollment. NOTE: If the device is not successfully enrolled during the enrollment period, the LED turns off and the device powers down. Activate a tamper, wired service (loop) or the reed switch to restart the enrollment process. 5. For each zone being used, press Edit to program it. Reed Switch Zone: press the Edit button to assign the Zone Descriptors and set the Device Types. Verify the Service and Response Types and set other options as desired. Press Save. Terminal Bock Zone: select to enable and press the Edit button to assign the Zone Descriptors and set the Device Types. Verify the Service and Response Types and set other options as desired. Press Save. NOTE: Once enrolled in a system, the SiXSHOCK cannot be used with another controller until it is removed from the current controller. See the Controllers instructions for details. Sensor Location Feature: To verify the location of each SiX device in an installation, enter programming mode and select a SiX device. The device LED lights. Select it again to turn the LED off or select the next device to locate. 2 For the Lyric Gateway Enroll and program using AlarmNet 360. Using AlarmNet 360 When AlarmNet 360 is ready to enroll, remove the sensor battery tab or use the magnet if the tab is removed. After the device is enrolled, the Green LED is on for 3 seconds. 6. Select SAVE again to complete enrollment. NOTE: If steps 5 and 6 are not completed, the device will automatically be deleted from the system when exiting Programming mode. After enrolling, verify adequate signal strength by conducting Go/No Go tests (see controllers instructions) with the device in its intended mounting location. Adjust the device location and orientation as necessary. 24-Hour Enrollment Deletion and Default If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended panel, reset the device to factory default setting:

1. Open the cover and remove the battery. 2. Hold down the tamper switch while reinserting the battery. 3. Reattach the cover. This procedure is available for 24 hours after enrollment with a panel and the device remains powered (battery installed). LED Indications LED Rapid Flashes for about 20 seconds, then ON for 3 seconds Status Power Up Enrollment Slow Flashes ON

(while in Programming Mode) Power Up Device enrolled; Wall or Cover Tamper activated. To stop flashes, clear the tamper condition by reconnecting to the mounting plate and reattaching the cover. It also times out after 10 minutes. Sensor LED toggles on and off when the sensor is selected. See Sensor Location Feature. (Not available with Lyric Gateway.) Battery Replacement Push the bottom latch of the mounting bracket back to disengage it. Then slide the back housing up and out to remove it from the mounting bracket. Slide the front and back housings in opposite directions and pull the housings apart. Remove the battery, wait 10 seconds, then insert a new battery. Recommended batteries:

Duracell DL123A Honeywell 466 Huiderui CR123A Panasonic CR123A Place the front and back housings together and slide them together. BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212F (100C) or incinerate. Dispose of used batteries properly. Keep away from children. NOTE: Constant exposure to high or low temperature or high humidity may reduce battery life. 3 Specifications:

Battery: 1 x 3V Lithium, Honeywell 466, Panasonic CR123A, Duracell DL123A or Huiderui CR123A Tamper: Cover and Wall RF Frequency: 2.4GHz Operating Temperature: 32 122 F / 0 50 C

(Agency Compliance 32 120 F / 0 49 C) Relative Humidity: 95% max. (Agency Compliance - 93% max.), non-condensing Dimensions: 1 H x 3.13 L x 1.61 W / 25.5 mm H x 79.5 mm L x 41 mm W Approval Listings:

FCC / IC cETLus Listed Conforms to UL 634 Certified to ULC/ORD-C634 Other Standards:

RoHS Product must be tested at least once each year FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

If using an indoor antenna, have a quality outdoor antenna installed. Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS dIndustrie Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. Warning The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-transmitter product procedures. RF EXPOSURE Exposition aux Frquences Radio : La/les antenne(s) utilise(s) pour cet metteur doit/doivent tre installe(s) une distance de sparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas tre situe(s) ni fonctionner paralllement tout autre transmetteur ou antenne, except en conformit avec les procdures de produit multi transmetteur FCC et ISED. Mise en Garde Support and Warranty REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. For the latest documentation and online support information, please go to:

https://mywebtech.honeywell.com/

For the latest warranty information, please go to:

www.honeywell.com/security/hsc/resources/wa. For patent information, see www.honeywell.com/patents MyWebTech Warranty 2017 Honeywell International Inc. Honeywell is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved. 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 www.honeywell.com/security Patents SiXSHOCK 800-23972 11/17 Rev A

The SiXSHOCK is a 3-zone wireless shock/door/window sensor intended for use with Honeywell controls that support SiX series devices. It provides a reed switch/magnet zone, external wired contact zone, and built-in shock sensor zone. Typical shock protection area:

10 - 12 sq. ft. / 5 - 6 foot radius (3.05m 3.66m / 1.52m 1.83m radius) The coverage area can vary depending on the mounting surface. Magnet Gap: Make gap is 0.8" (2.03cm); Break gap is 0.95" (2.4cm). A Terminal Block B Reed Switch C Shock Sensor D Tamper E LED F Magnet cart de l'aimant : cart l'tat ferm : 0,8 po

(2.03cm); cart l'tat ouvert : 0.95 po (2.4m). A Bornier B Contact lame C Shock Sensor D Antisabotage E DEL F Aimant NOTE: La longueur maximale du cblage est de 3 pi (91cm). NOTE: Wiring limit is 3ft. (91cm) The SiXSHOCK is a 3-zone wireless shock/door/window sensor intended for use with Honeywell controls that support SiX series devices. It provides a reed switch/magnet zone, external wired contact zone, and built-in shock sensor zone. Typical shock protection area:

10 - 12 sq. ft. / 5 - 6 foot radius (3.05m 3.66m / 1.52m 1.83m radius) The coverage area can vary depending on the mounting surface. SiXSHOCK Quick Installation Guide / Guide d'installation rapide Gua Rpida de Instalacin / Guia rpido de instalao The SiXSHOCK is a 3-zone wireless shock/door/window sensor intended for use with Honeywell controls that support SiX series devices. It provides a reed switch/magnet zone, external wired contact zone, and built-in shock sensor zone. Typical shock protection area:

10 - 12 sq. ft. / 5 - 6 foot radius (3.05m 3.66m /

1.52m 1.83m radius) The coverage area can vary depending on the mounting surface.. The SiXSHOCK is a 3-zone wireless shock/door/window sensor intended for use with Honeywell controls that support SiX series devices. It provides a reed switch/magnet zone, external wired contact zone, and built-in shock sensor zone. Typical shock protection area:

10 - 12 sq. ft. / 5 - 6 foot radius (3.05m 3.66m /

1.52m 1.83m radius) The coverage area can vary depending on the mounting surface. Interruptor de lengeta NOTA: El lmite de cableado es 91cm. Espacio del imn: El espacio de conexin es 2.03cm;

El espacio de desconexin es 2.4cm. A Bloque de terminales B C Shock Sensor D Manipulacin E LED Imn F Distncia do m: a distncia de contato 2.03cm; a distncia de perda de contato 2.4cm A Bloco terminal B C Shock Sensor D Tamper E LED m F NOTA: o limite de fiao de 0,9 metros. Interruptor de lminas After enrolling, verify adequate signal strength by conducting Go/No Go tests (see the controllers instructions) with the device in its intended mounting location. Adjust the device location and orientation as necessary. Signal Strength: Range of 1-4 bars (green); Should be minimum 1 green bar for the zone being programmed. Once enrolled, the device cannot be used with another system until it is removed from the current controller. See the controllers instructions. NOTE: After mounting you can use the Sensor Location feature to confirm device location. In programming mode, select a zone and the respective sensor LED lights. Aprs l'enrlement, vrifiez la puissance du signal adquate en effectuant des tests Go / No Go (voir les instructions du panneau de commande) avec le dispositif dans son emplacement de montage prvu. Au besoin, modifiez l'emplacement ou l'orientation du dispositif. Force du signal: devrait avoir au minimum 1 barre verte pour la zone programme. Une fois enrl, le dispositif ne peut pas tre utilis avec un autre systme avant d'avoir t supprim du panneau actuel. Reportez-vous aux instructions du panneau. NOTE : Aprs le montage, vous pouvez utiliser la fonction d'emplacement du dtecteur pour confirmer l'emplacement du dtecteur. En mode programmation, slectionnez une zone et le voyant du capteur respectif s'allume. For Lyric Controller / Pour le contrleur LyricMC /

Para el Controlador Lyric / Para o Controlador Lyric Enroll / Enrlement / Enrolar / Registrar Una vez registrado, verifique la intensidad de seal adecuada realizando pruebas Go / No Go (ver las instrucciones del controlador) con el dispositivo en la ubicacin deseada. Ajuste la ubicacin y orientacin del dispositivo segn sea necesario. Intensidad de la seal: Rango de 1-4 barras (verde); Debe ser mnimo 1 barra verde para la zona que se est programando. Una vez registrado, el dispositivo no se puede usar con otro sistema hasta que sea removido del controlador actual. Ver las instrucciones del controlador. NOTA : Despus de montar el sensor, puede utilizar la pantalla de localizacin de sensores para confirmar la ubicacin del dispositivo. En el modo de programacin, seleccione una zona y el respectivo LED de sensor se encender. Aps o registro, verifique a intensidade do sinal adequado ao realizar testes Go / No Go (consulte as instrues do controlador) com o dispositivo na localizao de montagem pretendida. Ajuste, se necessrio, o posicionamento e a orientao do dispositivo. Fora do Sinal: intervalo de 1-4 barras (verde); deve ter, no mnimo, uma barra verde para a zona em programao. Uma vez registrado, o dispositivo no pode ser usado com outro sistema at que seja removido do controlador atual. Consulte as instrues do controlador. NOTA: Aps a montagem, voc pode usar o recurso Sensor Location para confirmar a localizao do dispositivo. No modo de programao, selecione uma zona e a luz LED do respectivo sensor acender. For Lyric Gateway Enroll and program using AlarmNet 360. BATTERY CAUTION: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212F

(100C) or incinerate. Dispose of used batteries properly. Keep away from children. NOTE: Constant exposure to high or low temperature or high humidity may reduce battery life. Pour la Gateway Lyric MC Enrlez et programmez le systme au moyen dAlarmNet 360MC Attention de batterie: Risque d'incendie, d'explosion et de brlures. Ne rechargez pas, dmonter, chauffer au-dessus de 212F (100C), ou incinrer. Dbarrassez-vous des batteries utilises de faon approprie. Gardez partir des enfants. NOTE : Une exposition constante des tempratures leves ou basses ou un taux d'humidit leve peut rduire la dure de vie de la pile. Para Lyric Gateway Registro y programacin usando AlarmNet 360 Precauciones con respecto a las bateras: Riesgo de FUEGO, explosin y quemaduras. No recargar, desarmar, calentar por encima de 100C (212F), o incinerar. Descarte Apropiadamente las bateras usadas. Mantngalas fuera del alcance de los nios. NOTA: Exposicin constante a altas o bajas temperaturas o alta humedad puede reducir la vida til de la batera. Para o Gateway Lyric Faa o registro e programe usando o AlarmNet 360. Precaues com a bateria: Risco de incndio, exploso e queimaduras. No recarregar, no desmontar, no aquecer mais de 100C (212F) nem incinerar. Descarte as baterias usadas apropriadamente. Mantenha fora do alcance de crianas. NOTA: A exposio constante a temperatura alta ou baixa ou alta umidade podem reduzir a vida til da batera If using an indoor antenna, have a quality outdoor antenna installed. FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC et exempt de licence RSS dIndustrie Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. RF EXPOSURE Warning The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 in (20 cm) from all persons and must not be co-located or operated in conjunction with any other transmitter except in accordance with FCC and ISED multi-transmitter product procedures. Mise en Garde Exposition aux Frquences Radio: La/les antenne(s) utilise(s) pour cet metteur doit/doivent tre installe(s) une distance de sparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas tre situe(s) ni fonctionner paralllement tout autre transmetteur ou antenne, except en conformit avec les procdures de produit multi transmetteur FCC et ISED. DECLARACIN IFETEL La operacin de este equipo est sujeta a las siguientes dos condiciones 1. Es posible que este equipo o dispositivo no cause interferencia perjudicial y 2. Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. DECLARAO ANATEL Este equipamento no tem direito proteo contra interferncia prejudicial e no pode causar interferncia em sistemas devidamente autorizados. Para maiores informaes, consulte o site da ANATEL www.anatel.gov.br. Replace Battery / Remplacement des piles /

Cambiar batera / Substituir bateria U.S. warranty / U.S. garantie / U.S. garantie / U.S. garantia www.honeywell.com/security/hsc/resources/wa Patents / Brevets / Patentes / Patentes www.honeywell.com/patents Support / Soutien / Soporte / Suporte https://mywebtech.honeywell.com/

Specifications / Spcifications / Especificaciones / Especificaes:

Battery / Pile / Batera / Bateria: 1 x 3V, Lithium; Honeywell 466, Panasonic CR123A, Duracell DL123A, Tamper / Interrupteurs antisabotage / Manipulacin / Tamper: Cover and Wall / Couvercle et Mur /

Huiderui CR123A Tapa y Pared / Tampa e Parede RF Frequency / Frquence RF / Frecuencia de RF / Frequncia RF: 2.4GHz Operating Temperature / Temprature de fonctionnement / Temperatura de funcionamiento / Temperatura de operao: 32 122F / 0 50C (Agency Compliance 32 120F / 0 49C) Relative Humidity / Humidit relative / Humedad relativa / Umidade relativa: 95% max. (Agency Compliance -

93% max.), non-condensing / sans condensation / sin-condensacin / sem condensao Dimensions / Dimensions / Dimensiones / Dimenses: 1 H x 3.13 L x 1.61 W / 25.5 mm H x 79.5 mm L x 41 mm W REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM. Product must be tested at least once each year MyWebTech Warranty POUR LES LIMITES DU SYSTME DALARME AU COMPLET, REPORTEZ-VOUS AU GUIDE DINSTALLATION DU PANNEAU DE COMMANDE. Le fonctionnement du produit doit tre vrifi au moins une fois par anne 2017 Honeywell International Inc. Honeywell is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved www.honeywell.com/security 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 Approval Listings /

Approbations Homologations /

Listas de aprobaciones /

Listagens de aprovao:

FCC / IC ETL Listed to UL 634 cETL Listed to ULC/ORD-C634 Other Standards: RoHS Patents CONSULTE LAS INSTRUCCIONES DE INSTALACIN PARA EL CONTROLADOR CON EL CUAL SE UTILIZA ESTE DISPOSITIVO, PARA OBTENER DETALLES CON RESPECTO A LAS LIMITACIONES DE TODO EL SISTEMA DE ALARMA. El producto debe ser probado al menos una vez al ao PARA SABER MAIS SOBRE AS LIMITAES DE TODO O SISTEMA DE ALARME, CONSULTE AS INSTRUES DE INSTALAO DO CONTROLE COM O QUAL ESTE DISPOSITIVO USADO. O produto deve ser testado pelo menos uma vez por ano 800-15959) SiXSHOCK 800-23809 11/17 Rev A