all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
user manual | Users Manual | 5.51 MiB | April 01 2016 | |||
1 | Operational Description | April 01 2016 | ||||||
1 | Cover Letter(s) | April 01 2016 | ||||||
1 | External Photos | April 01 2016 | ||||||
1 | ID Label/Location Info | April 01 2016 | ||||||
1 | Internal Photos | April 01 2016 | ||||||
1 | RF Exposure Info | April 01 2016 | ||||||
1 | Cover Letter(s) | April 01 2016 | ||||||
1 | Test Report | April 01 2016 | ||||||
1 | Test Setup Photos | April 01 2016 |
1 | user manual | Users Manual | 5.51 MiB | April 01 2016 |
33-00135EFS_B.book Page 1 Wednesday, November 11, 2015 11:31 AM ERM5220R Equipment Remote Module WITH REDLINK WIRELESS TECHNOLOGY INSTALL GUIDE Table of Contents About the ERM5220R Installation Checklist Terminal Designations Installation Checkout Troubleshooting Specifications 5 Year Warranty 2 3 4 6 12 14 16 18 CAUTION Read these installation instructions completely and follow them carefully. Installation must be performed by a qualified service technician and must comply with local codes. Disconnect power to all relevant devices before installing or servicing the ERM. Failure to connect the device according to these instructions may result in damage to the device, the controls, and/or personal injury. 33-00135EFS-03 33-00135EFS_B.book Page 2 Wednesday, November 11, 2015 11:31 AM About the ERM5220R THERMOSTAT ERM BOILER ERM WIRE CONDENSING UNIT Fig. 1. MCR35654 Wireless RedLink communication between condensing unit/
compressor or boiler and thermostat. Eliminates the need to run additional wires to your equipment, for example, during a heat pump upgrade. Suitable for outdoor use. Temperature sensor terminals for outdoor temp sensors or indoor freeze protection. LEDs for easy installation checkout. May reduce damage to homes since wiring/drilling is eliminated. NOTE: The ERM5220R must be used with updated THX9421R5021, TH8321R1001 and/or EIM. Look for this image on these products. 33-00135EFS03 2 33-00135EFS_B.book Page 3 Wednesday, November 11, 2015 11:31 AM Installation Checklist MATERIALS SUPPLIED:
ERM5220R Equipment Remote Module WITH REDLINK WIRELESS TECHNOLOGY INSTALL GUIDE Table of Contents About the ERM5220R Installation Checklist Terminal Designations Installation Checkout Troubleshooting Specifications 5 Year Warranty 2 3 4 6 12 14 16 18 CAUTION Read these installation instructions completely and follow them carefully. Installation must be performed by a qualified service technician and must comply with local codes. Disconnect power to all relevant devices before installing or servicing the ERM. Failure to connect the device according to these instructions may result in damage to the device, the controls, and/or personal injury. 33-00135EFS-03 M35671 ERM5220R Wall Anchors (x2) and Mounting Screws (x2) Extra Cover Screw (optional) Installation Instructions TOOLS NEEDED (NOT SUPPLIED):
M35669 M35672 M35670 Drill Nut Driver Attachment for Drill Wire Stripper Small Flathead Screwdriver Phillips Screwdriver 120/240 V to 24 V Transformer (optional) 3 33-00135EFS03 33-00135EFS_B.book Page 4 Wednesday, November 11, 2015 11:31 AM Terminal Designations I I I D E Y A L P S D E B L L W H C H W S E R U T A R E P M E T R O O D T U O E S N E S O T D E S U E B N A C
. R O S N E S E R U T A R E P M E T M H O K 0 1 R O F S L A N M R E T I
. I T A T S O M R E H T K N L d e R E L B T A P M O C A N O I
. I I T A T S O M R E H T K N L d e R E L B T A P M O C O T D E T A C N U M M O C E B L L W E C N E R R U C C O T L U A F I I
. I L A N M R E T T L U A F E N L R O S S E R P M O C I 1
. I I T A T S O M R E H T K N L d e R E L B T A P M O C O T D E T A C N U M M O C E B L L W E C N E R R U C C O T S O R F E D I I
. I L A N M R E T T S O R F E D R O S S E R P M O C
. E S U R O S S E R P M O C R O F E C A L P N I E B D L U O H S R D N A J N E E W T E B R E P M U J
. R E P M U J R O F L A N M R E T I
. R E W O P C A V 4 2 R O F S L A N M R E T I
. R O S S E R P M O C E G A T S O W T F O E G A T S D N O C E S
. R O S S E R P M O C E G A T S O W T F O E G A T S T S R F I I P. M U P T A E H N O E V L A V G N S R E V E R R O F L A N M R E T B O
/
I 5 5 6 5 3 M T O N O D
, I D E R S E D T O N S I 1 X U A O T D F I
. I 1 X U A R E W O P L L W L A N M R E T D N O T U P N I I I E V T C A
. T S O R F E D R O F T U P N I N A S A S E T A R E P O L A N M R E T D E H T I I R O S S E R P M O C A H T W E S U R O F D E R U G F N O C S I I R 0 2 2 5 M R E E H T E H T N E H W E V T C A Y L N O S I I E R U T A E F S H T I
. R 0 2 2 5 M R E E H T O T L A N M R E T D T C E N N O C I R O S S E R P M O C R O F S N O T A N G S E D L A N M R E T I I I DLS1S1 T O/B T Y2 JRCY 1 Fig. 2. Terminal Designations for Compressor. 33-00135EFS03 4 33-00135EFS_B.book Page 5 Wednesday, November 11, 2015 11:31 AM T A T S O M R E H T E H T F O E S A C E H T N I I N O T C E T O R P E Z E E R F R O F D E S U E B N A C
. R O S N E S E R U T A R E P M E T M H O K 0 1 R O F S L A N M R E T I
. I N O T C E T O R P E Z E E R F R O F D E S U E B O T S R O O D N I I N A M E R T S U M R O S N E S
. M R E E H T O T L A N G S E H T G N S O L I I
. I E S U R E L O B R O F D E V O M E R E B D L U O H S R D N A J N E E W T E B R E P M U J
. R E P M U J R O F L A N M R E T I
. L L A C T A E H R O F L A N M R E T I
. L L A C T A E H R O F L A N M R E T I
. R E W O P C A V 4 2 R O F S L A N M R E T I TDLS1S1 O/B T Y2 JRCY I I R E L O B R O F S N O T A N G S E D L A N M R E T I I A 6 5 6 5 3 M
. I S E M T L L A T A F F O E B L L A H S Y A L E R Y E H T
, I R E L O B A S A D E R U G F N O C N E H W I
. I I N O T A R E P O 0 2 S E R E S T R O P P U S T O N L L W M R E I
:
E T O N Fig. 3. Terminal Designations for Boiler. 5 33-00135EFS03 33-00135EFS_B.book Page 6 Wednesday, November 11, 2015 11:31 AM INSTALLATION IMPORTANT The ERM is not compatible with RedLink Zone boards. To ensure that the ERM will receive a wireless signal at the desired installation location, follow steps 1 to 5 in the Wiring section. If your location has metal siding, the ERMs signal may be affected. If there is no communication or poor signal strength, consider a different location. A Prestige (with EIM) or VisionPRO (with or without EIM) will only allow one of the following configurations:
1) Enrolled with a single boiler configured ERM;
2) Enrolled with a single compressor configured ERM;
3) Enrolled with a single boiler configured ERM and enrolled with a single compressor configured ERM. Wiring 1. Make sure power to compressor/boiler is off. 2. Remove the front cover by loosening the cover screw and lifting up from the bottom of the ERM. 3. Remove 3 to 4 inches of the cables outer sheathing, then remove 3/8 to 1/2 inch of insulation from each wire. Fig. 4. Cable prepared for wiring. M35674 33-00135EFS03 6 33-00135EFS_B.book Page 7 Wednesday, November 11, 2015 11:31 AM 4. For compressor applications: Leave the jumper between termi-
nals J and R in place. For boiler applications: Remove the jumper between terminals J and R. FOR COMPRESSOR:
Jumper J and R FOR BOILER:
Remove Jumper J R C Y Y2 T O/B T D L S1 S1 Fig. 5. Terminal Designations showing the jumper between J and R terminals. MCR35657 5. For compressors and boilers: Connect a 24 VAC power source to the R and C terminals on the ERM. J R C Y Y2 T O/B T D L S1 S1 24 VAC V c.a. 24V CAN COME FROM AIR HANDLER
(COMPRESSOR APPLICATION) OR EXTERNAL TRANSFORMER M35658 Fig. 6. Once power is connected, the Compressor (or Boiler) LED should illuminate green. (Fig. 7) Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating OR Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating MCR35659 MCR35660 Fig. 7. 7 33-00135EFS03 33-00135EFS_B.book Page 8 Wednesday, November 11, 2015 11:31 AM 6. For compressors and boilers: Put the thermostat in pairing mode by selecting add a device from the installer menu. See thermostat manual for further details. Once the thermostat is in pairing mode, press and quickly release the Connect button on the ERM. When the ERM is connected to the system, the ERMs Con-
nected LED will be solid green and the thermostat will show ERM in its Wireless Manager. (Fig. 8) Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating OR Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating MCR35661 MCR35662 Fig. 8. 7. Connect terminals from the ERM to the appropriate terminals on the compressor/boiler control board. COMPRESSOR J R C Y Y2 T O/B T D L S1 S1 24 VAC V c.a. C Y R D L EQUIPMENT CONTROL BOARD Y2 O/B 10K OHM OUTDOOR TEMPERATURE SENSOR (OPTIONAL) M35668 Fig. 9. 33-00135EFS03 8 33-00135EFS_B.book Page 9 Wednesday, November 11, 2015 11:31 AM BOILER J R C Y Y2 T O/B T D L S1 S1 24 VAC V c.a. T T EQUIPMENT CONTROL BOARD 10K OHM INDOOR TEMPERATURE SENSOR
(RECOMMENDED) M35673 Fig. 10. IMPORTANT If the ERM was previously used with a compressor and will now be used with a boiler:
1) un-enroll the ERM at the thermostat;
2) remove the jumper on the ERM;
3) designate Radiant Heat for Heating System Type
(ISU 2000) in your thermostat. Mounting ERM 8. Use two screws and wall anchors to attach the ERM to the exterior wall near the compressor. The location should be at least 3 feet above ground and oriented with the two wire exits facing downward. See Figs. 11 and 12. 9 33-00135EFS03 33-00135EFS_B.book Page 10 Wednesday, November 11, 2015 11:31 AM 9. Attach cover and secure with bottom screw (Fig. 13). MOUNTING SCREWS Equipment Remote Module I ERM5000R Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating J R C Y1 Y2 T O/B T D L S1 S1 Compressor:
Jump J and R Boiler:
Remove Jumper R 0 0 0 5 M R E l I e u d o M e t o m e R t n e m p u q E i g n i t c e n n o C e c v e D i
:
i g n h s a F l S U T A T S D E L D E T C E N N O C d e t c e n n o C e c v e D i
:
n e e r G i g n i t a c n u m m o C t o N
:
d e R t c e n n o C r e l i o B d e t c e n n o C r o s s e r p m o C 1 S 1 S L D B
/
O T 2 Y T 1 Y C R J
:
r o s s e r p m o C R d n a J p m u J
:
r e l i o B r e p m u J e v o m e R TDLS1S1 O/B JRCY1Y2 T Remove Jumper Boiler:
Jump J and R Compressor:
Red: Not Communicating Green: Device Connected Flashing: Device Connecting CONNECTED LED STATUS Connect Connected Boiler Compressor Equipment Remote Module I ERM5000R CORRECT INCORRECT INCORRECT MCR35665 Fig. 11. Mounting orientation. MINIMUM 1/4 INCH GAP Fig. 12. If mounting on lap siding, allow space for the cover to be removed. M35666 33-00135EFS03 10 33-00135EFS_B.book Page 11 Wednesday, November 11, 2015 11:31 AM M35667 Fig. 13. 11 33-00135EFS03 33-00135EFS_B.book Page 12 Wednesday, November 11, 2015 11:31 AM Checkout Power the system on. Use the thermostat to start a cooling or heating cycle, testing the ERM. 1. Restore power to the compressor/boiler as well as your RedLink system. for heat/cooling. active. 2. Raise/lower the set point on the zone thermostat to initiate a call 3. Observe all control devices to ensure operation and heat/cooling is 4. Lower/raise the set point on the thermostat to suspend the call for heat/cooling. If outdoor temperature sensor is used, check thermostat to see the readings are active and accurate. 6. Be sure to set thermostat to the desired settings when checkout is 5. complete. 33-00135EFS03 12 33-00135EFS_B.book Page 13 Wednesday, November 11, 2015 11:31 AM M35680 Fig. 14. 13 33-00135EFS03 33-00135EFS_B.book Page 14 Wednesday, November 11, 2015 11:31 AM TROUBLESHOOTING NOTE: Disconnect RedLink when making changes to the device. RESET PROCEDURE:
Hold down the Connect button on the ERM for 10 seconds. The Connection LED should appear red for a few seconds and go out. This indicates the unit is reset. Symptom Possible Cause Relays dont switch as expected Incorrect jumper configuration Connected LED is red Loss of communication with system Connected LED is off Device is not enrolled No LEDs are on with system No power to device Action Check jumper configuration. If incorrect, unenroll from system, change jumper, then re-enroll with system. Verify thermostat and/
or Equipment Interface Module are powered and functioning correctly. Enroll with system. Verify 24 VAC at R/C terminals. 33-00135EFS03 14 33-00135EFS_B.book Page 15 Wednesday, November 11, 2015 11:31 AM Symptom Possible Cause Action No outdoor temperature shown on thermostat No wired outdoor temperature sensor connected to ERM, or device configured as boiler Thermostat shows for outdoor temperature Outdoor temperature reading at thermostat is too high Wired outdoor temperature sensor failed Sun load on sensor Compressor doesnt turn on, Y LED is blinking Emergency backup control doesnt function
(if configured as boiler) 5-minute compressor lockout after power cycle No valid indoor temperature sensor Connect outdoor temperature sensor to S1/S1 terminals. Device only reports outdoor temperature temperature when configured as compressor. Check sensor for short circuit or open circuit. Verify outdoor temperature sensor is not in direct sunlight. May need to use longer wire to mount in ideal location. Wait 5 minutes, compressor will turn on after safety timeout. Check sensor for short circuit or open circuit, or install indoor temperature sensor on S1/S1 terminals. 15 33-00135EFS03 33-00135EFS_B.book Page 16 Wednesday, November 11, 2015 11:31 AM SPECIFICATIONS Operating Ambient Temperature Range:
Compressor: -40 to +155 F (-40 to +68 C) Boiler: 30 to +130 F (-1 to +54 C) Operating Relative Humidity Range: 0 - 99 %
Electrical:
24 VAC, 50/60 Hz. Dimensions:
175 mm x 168 mm x 38 mm Wireless capability via RedLink technology. 6-39/64
(168) 6-7/8 (175) Fig. 15. Dimensions. 1-31/64
(38) M35664 33-00135EFS03 16 33-00135EFS_B.book Page 17 Wednesday, November 11, 2015 11:31 AM SEPARABLE PARTS ERM with TH8321R1001/U: YERM5220R8321 ERM with TH8321R1001/U and THM5421R1021: YERM5220RVPEIM FCC REGULATIONS 15.19 (a)(3) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. IC REGULATIONS RSS-GEN This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
1. This device may not cause interference; and 2. This device must accept any interference, including interference that may cause undesired operation of the device. FCC Warning (Part 15.21) (USA only) Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 17 33-00135EFS03 33-00135EFS_B.book Page 18 Wednesday, November 11, 2015 11:31 AM 5 YEAR WARRANTY Honeywell warrants this product to be free from defects in the workmanship or materials, under normal use and service, for a period of five (5) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell's option). If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or
(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will make the determination whether the product should be returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1985 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you. This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect was caused by damage which occurred while the product was in the possession of a consumer. Honeywells sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE FIVE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you have any questions concerning this warranty, please write Honeywell Customer Care, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-
1502. 33-00135EFS03 18 33-00135EFS_B.book Page 19 Wednesday, November 11, 2015 11:31 AM 19 33-00135EFS03 33-00135EFS_B.book Page 20 Wednesday, November 11, 2015 11:31 AM Automation and Control Solutions Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 yourhome.honeywell.com U.S. Registered Trademark 2015 Honeywell International Inc. 33-00135EFS03 M.S. 11-15 Printed in United States 33-00135EFS_B.book Page 1 Wednesday, November 11, 2015 11:31 AM ERM5220R Module d'quipement distance (ERM) AVEC TECHNOLOGIE SANS FIL REDLINK GUIDE DINSTALLATION Table des matires propos du module ERM5220R 2 Liste de vrification pour linstallation 3 4 Dsignations des bornes Installation 6 12 Vrification 14 Dpannage 16 Caractristiques Garantie de 5 ans 18 MISE EN GARDE Lire cette notice d'installation dans son intgralit et bien respecter les instructions. Linstallation doit tre effectue par un technicien dentretien qualifi et conformment aux codes locaux en vigueur. Couper lalimentation vers lappareil avant dinstaller ou de rparer ce module ERM. Un raccordement de cet appareil non conforme ces instructions peut endommager lappareil ou les rgulateurs et causer des blessures. 33-00135EFS-03 33-00135EFS_B.book Page 2 Wednesday, November 11, 2015 11:31 AM propos du module ERM5220R THERMOSTAT MODULE ERM CHAUDIRE Fig. 1. MODULE ERM FIL UNIT DE CONDENSATION MFCR35654 Communication sans fil RedLink entre le unit de condensation/compresseur ou la chaudire et le thermostat. limine la ncessit d'acheminer des fils supplmentaires vers l'quipement, pour la mise niveau d'une thermopompe par exemple. Compatible avec une utilisation l'extrieur. Bornes de capteur de temprature pour capteurs de temprature extrieure ou protection antigel intrieure. Tmoins DEL pour une vrification aise de l'installation. L'absence de cblage et de perage peut minimiser les dommages de l'habitation. REMARQUE : Le module ERM5220R doit tre utilis avec les dispositifs THX9421R5021, TH8321R1001 ou un module d'interface d'quipement (EIM) mis jour. Rechercher cette image sur ces produits. 33-00135EFS03 2 33-00135EFS_B.book Page 3 Wednesday, November 11, 2015 11:31 AM Liste de vrification pour linstallation MATRIEL FOURNI :
ERM5220R Equipment Remote Module WITH REDLINK WIRELESS TECHNOLOGY INSTALL GUIDE Table of Contents About the ERM5220R Installation Checklist Terminal Designations Installation Checkout Troubleshooting Specifications 5 Year Warranty 2 3 4 6 12 14 16 18 CAUTION Read these installation instructions completely and follow them carefully. Installation must be performed by a qualified service technician and must comply with local codes. Disconnect power to all relevant devices before installing or servicing the ERM. Failure to connect the device according to these instructions may result in damage to the device, the controls, and/or personal injury. 33-00135EFS-03 M35671 ERM5220R Ancres murales (2) et vis de montage (2) Vis de couvercle supplmentaire (en option) Notice d'installation OUTILS REQUIS (NON FOURNIS) :
M35669 M35672 M35670 Perceuse Douille tourne-crou pour la perceuse Dnudeur de fils Petit tournevis plat Tournevis cruciforme Transformateur 120/240 V 24 V (en option) 3 33-00135EFS03 33-00135EFS_B.book Page 4 Wednesday, November 11, 2015 11:31 AM Dsignations des bornes
. I I I E L B T A P M O C K N L d e R T A T S O M R E H T U A E U Q N U M M O C A R E S E C N A L L A F D A L E D E C N E R R U C C O L
'
I
. I R U E S S E R P M O C U D E N G L E D E C N A L L A F D E D E N R O B I I S E R U E R T X E S E R U T A R P M E T S E L R E T C E T D R U O P S E S L T U E R T T N E V U E P I I
. S M H O K 0 1 E R U T A R P M E T E D R U E T P A C R U O P S E N R O B
. I I E L B T A P M O C K N L d e R T A T S O M R E H T N U R U S S E H C F F A T N O R E S I I U Q 1
. I I I E L B T A P M O C K N L d e R T A T S O M R E H T U A E U Q N U M M O C A R E S E G A R V G D U D E C N E R R U C C O L
'
I
. R U E S S E R P M O C U D E G A R V G D E D E N R O B I
. E P M O P O M R E H T A L E D N O S R E V N I I
'
D E N N A V A L R U O P B O E N R O B
/
. S E G A T X U E D R U E S S E R P M O C U D E G A T E M X U E D I
. S E G A T X U E D R U E S S E R P M O C U D E G A T R E M E R P I
. I
. A C V 4 2 N O T A T N E M L A R U O P S E N R O B I
. I I
'
R U E S S E R P M O C C E V A N O T A C L P P A L R U O P E C A L P N E E R T T O D R T E J E R T N E R E L A V A C E L I I
. I R E L A V A C R U O P E N R O B S A P E N
, I T A H U O S S A P T S E N A L E C
'
I S
. I 1 X U A E T N E M L A D E N R O B A L R U S E V T C A E R T N E L
'
I
. I E G A R V G D E L R U O P E R T N E D T R E S D E N R O B A L
'
5 5 6 5 3 F M I R U G F N O C T S E R 0 2 2 5 M R E E L U D O M E L E U Q S R O L E U Q E V T C A T S E N N O T C N O F E T T E C
'
I I
. R 0 2 2 5 M R E E L U D O M U A D E N R O B A L R E H C N A R B
. R U E S S E R P M O C N U C E V A N O T A S L T U E N U R U O P I I I DLS1S1 T O/B T Y2 JRCY 1 Fig. 2. Dsignations des bornes pour le compresseur. R U E S S E R P M O C E L R U O P S E N R O B S E D S N O T A N G S D I I 33-00135EFS03 4 33-00135EFS_B.book Page 5 Wednesday, November 11, 2015 11:31 AM I S A C N E L E G E L E R T N O C N O T C E T O R P A L R U O P S L T U E R T T U E P I I
. S M H O K 0 1 E R U T A R P M E T E D R U E T P A C R U O P S E N R O B E R T R U O P R U E R T N I I
'
I L R E T S E R T O D R U E T P A C E L
. M R E E L U D O M E L T E T A T S O M R E H T E L E R T N E L A N G S E D E T R E P E D I
. I L E G E L E R T N O C N O T C E T O R P E M M O C S L T U I I
. E G A F F U A H C E D L E P P A R U O P E N R O B
. E G A F F U A H C E D L E P P A R U O P E N R O B
. I
. A C V 4 2 N O T A T N E M L A R U O P S E N R O B I
. I I I
'
E R D U A H C C E V A N O T A C L P P A L R U O P R T E R E R T T O D R T E J E R T N E R E L A V A C E L I I I
. I R E L A V A C R U O P E N R O B TDLS1S1 O/B T Y2 JRCY I E R D U A H C A L R U O P S E N R O B S E D S N O T A N G S D I I A 6 5 6 5 3 F M
. E C N E N A M R E P N E V T C A S D I I T S E Y S A L E R E L
, I E R D U A H C C E V A S N O T A C L P P A S E L R U O P I I
. I I 0 2 E R S A L C E V A E L B T A P M O C S A P T S E N M R E L
'
'
:
E U Q R A M E R Fig. 3. Dsignations des bornes pour la chaudire. 5 33-00135EFS03 33-00135EFS_B.book Page 6 Wednesday, November 11, 2015 11:31 AM INSTALLATION IMPORTANT RedLink. Le module ERM n'est pas compatible avec les tableaux de zone Pour s'assurer que le module ERM recevra un signal sans fil l'emplacement souhait pour l'installation, suivre les tapes 1 5 de la section Cblage. Si l'emplacement comporte un bardage mtallique, le signal de l'ERM peut en tre affect. En cas d'absence de communication ou d'intensit insuffisante du signal, considrer un autre emplacement. Les thermostats Prestige (avec EIM) ou VisionPRO (avec ou sans EIM) ne permettront que l'une des configurations suivantes :
1) Enregistrement avec un ERM configur pour une seule chaudire;
2) Enregistrement avec un ERM configur pour un seul compresseur;
3) Enregistrement avec un ERM configur pour une seule chaudire et enregistrement avec un ERM configur pour un seul compresseur. Cblage 1. S'assurer que l'alimentation vers le compresseur/la chaudire est coupe. 2. Retirer le couvercle avant en desserrant la vis du couvercle et en le relevant du bas de l'ERM. 3. Retirer 3 4 pouces de la gaine extrieure du cble, puis retirer 3/8 1/2 pouce d'isolation de chaque fil. Fig. 4. Cble prpar pour le raccordement. M35674 33-00135EFS03 6 33-00135EFS_B.book Page 7 Wednesday, November 11, 2015 11:31 AM 4. Pour les applications avec compresseur : Laisser le cavalier en place entre les bornes J et R. Pour les applications avec chaudire : Retirer le cavalier entre les bornes J et R. FOR COMPRESSOR:
Jumper J and R FOR BOILER:
Remove Jumper J R C Y Y2 T O/B T D L S1 S1 Fig. 5. Dsignations des bornes montrant le cavalier entre les bornes J et R. MCR35657 5. Pour les compresseurs et les chaudires : Brancher une source d'alimentation de 24 V c.a. sur les bornes R et C du module ERM. J R C Y Y2 T O/B T D L S1 S1 24 V c.a. 24 V PROVENANT DU SYSTME DE TRAITEMENT DE L'AIR (APPLICATION AVEC COMPRESSEUR) OU D'UN TRANSFORMATEUR EXTERNE MF35658 Fig. 6. Une fois l'alimentation connecte, le tmoin DEL Compressor
(Compresseur) ou Boiler (Chaudire) devrait s'allumer en vert. (Fig. 7) Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating OU Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating MCR35659 MCR35660 Fig. 7. 7 33-00135EFS03 33-00135EFS_B.book Page 8 Wednesday, November 11, 2015 11:31 AM 6. Pour les compresseurs et les chaudires : Mettre le thermostat en mode d'appairage en slectionnant Add a device (Ajouter un appareil) dans le menu de l'installateur. Consulter le manuel du thermostat pour plus de dtails. Une fois le thermostat en mode d'appairage, appuyer rapidement sur le bouton Connect
(Connexion) sur le module ERM. Une fois le module ERM connect au systme, son tmoin DEL de connexion s'allume en vert en continu et le thermostat indique ERM dans le gestionnaire des dispositifs sans fil. (Fig. 8) Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating OU Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating MCR35661 MCR35662 Fig. 8. 7. Connecter les bornes du module ERM aux bornes appropries du tableau de contrle du compresseur/de la chaudire. COMPRESSEUR J R C Y Y2 T O/B T D L S1 S1 24 V c.a. CAPTEUR DE TEMPRATURE EXTRIEURE 10 K OHMS
(EN OPTION) R C Y Y2 O/B D L TABLEAU DE CONTRLE DE L'QUIPEMENT MF35668 Fig. 9. 33-00135EFS03 8 33-00135EFS_B.book Page 9 Wednesday, November 11, 2015 11:31 AM CHAUDIRE J R C Y Y2 T O/B T D L S1 S1 24 V c.a. T T TABLEAU DE CONTRLE DE L'QUIPEMENT CAPTEUR DE TEMPRATURE INTRIEURE 10 K OHMS
(RECOMMAND) MF35673 Fig. 10. IMPORTANT Si le module ERM a prcdemment t utilis avec un compresseur et est maintenant destin tre utilis avec une chaudire :
1) annuler l'enregistrement du module ERM sur le thermostat;
2) retirer le cavalier du module ERM;
3) indiquer Radiant Heat for Heating System Type (ISU 2000)
(Chauffage rayonnant pour type de systme de chauffage) sur le thermostat. Montage du module ERM 8. Utiliser deux vis et deux ancres murales pour fixer le module ERM sur le mur extrieur prs du compresseur. L'emplacement doit tre situ au moins 3 pieds au-dessus du sol et orient avec les deux sorties de fil face vers le bas. Voir les Figs. 11 et 12. 9 33-00135EFS03 33-00135EFS_B.book Page 10 Wednesday, November 11, 2015 11:31 AM 9. Attacher le couvercle et le fixer avec la vis infrieure (Fig. 13). VIS DE MONTAGE Equipment Remote Module I ERM5000R Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating J R C Y1 Y2 T O/B T D L S1 S1 Compressor:
Jump J and R Boiler:
Remove Jumper R 0 0 0 5 M R E l I e u d o M e t o m e R t n e m p u q E i g n i t c e n n o C e c v e D i
:
d e t c e n n o C e c v e D i i g n h s a F l
:
n e e r G S U T A T S D E L D E T C E N N O C i g n i t a c n u m m o C t o N
:
d e R t c e n n o C r e l i o B d e t c e n n o C r o s s e r p m o C 1 S 1 S L D B
/
O T 2 Y T 1 Y C R J
:
r o s s e r p m o C R d n a J p m u J
:
r e l i o B r e p m u J e v o m e R TDLS1S1 O/B JRCY1Y2 T Remove Jumper Boiler:
Jump J and R Compressor:
Red: Not Communicating Green: Device Connected Flashing: Device Connecting CONNECTED LED STATUS Connect Connected Boiler Compressor Equipment Remote Module I ERM5000R CORRECTE INCORRECTE INCORRECTE MFCR35665 Fig. 11. Orientation de montage. ESPACEMENT MINIMUM 1/4 PO Fig. 12. Si le montage a lieu sur un bardage clin, laisser suffisamment d'espace pour permettre le retrait du couvercle. 33-00135EFS03 10 33-00135EFS_B.book Page 11 Wednesday, November 11, 2015 11:31 AM M35667 Fig. 13. 11 33-00135EFS03 33-00135EFS_B.book Page 12 Wednesday, November 11, 2015 11:31 AM Vrification Mettre le systme sous tension. Utiliser le thermostat pour lancer un cycle de chauffage ou de refroidissement pour tester le module ERM. 1. Restaurer l'alimentation vers le compresseur/la chaudire ainsi que vers le systme RedLink. 2. Hausser/rduire le point de consigne sur le thermostat de zone pour lancer un appel de chauffage/refroidissement. 3. Observer tous les dispositifs de rgulation pour vrifier qu'ils fonctionnent bien et que le chauffage/refroidissement est actif. 4. Rduire/hausser le point de consigne sur le thermostat pour lancer un appel de chauffage/refroidissement. 5. Si le capteur de temprature extrieure est utilis, vrifier que les valeurs indiques sur le thermostat sont actives et prcises. 6. Veiller rgler le thermostat aux rglages dsirs une fois la vrification termine. 33-00135EFS03 12 33-00135EFS_B.book Page 13 Wednesday, November 11, 2015 11:31 AM M35680 Fig. 14. 13 33-00135EFS03 33-00135EFS_B.book Page 14 Wednesday, November 11, 2015 11:31 AM DPANNAGE REMARQUE : Dbrancher le systme RedLink avant de procder des modifications sur le dispositif. PROCDURE DE RINTIALISATION :
Appuyer pendant 10 secondes sur le bouton Connect (Connexion) du module ERM. Le tmoin DEL de connexion doit s'allumer en rouge pendant quelques secondes, puis s'teindre. Ceci indique que l'unit a t rinitialise. Symptme Cause possible Action Les relais ne s'enclenchent pas comme prvu Configuration incorrecte du cavalier Le tmoin DEL de connexion est rouge Perte de communication avec le systme Le tmoin DEL de connexion est teint Aucun tmoin DEL n'est allum L'appareil n'est pas enregistr dans le systme L'appareil n'est pas aliment 33-00135EFS03 14 Contrler la configuration du cavalier. Si elle est incorrecte, annuler l'enregistrement, modifier le cavalier, puis enregistrer de nouveau l'appareil. Vrifier que le thermostat et/ou le module d'interface d'quipement sont aliments et fonctionnent correctement. Enregistrer l'appareil dans le systme. Vrifier que 24 V c.a. sont prsents aux bornes R/C. 33-00135EFS_B.book Page 15 Wednesday, November 11, 2015 11:31 AM Symptme Cause possible Action Le thermostat n'affiche pas la temprature extrieure Aucun capteur de temprature extrieure n'est connect au module ERM, ou l'appareil est configur sur chaudire Le thermostat indique pour la temprature extrieure La temprature extrieure indique sur le thermostat est trop leve Dfaillance du capteur de temprature extrieure avec fil Charge solaire sur le capteur Verrouillage du compresseur de 5 minutes aprs le cycle de mise sous tension Pas de capteur de temprature intrieure valide Le compresseur ne se met pas en marche, le tmoin DEL Y clignote La rgulation de secours en cas d'urgence ne fonctionne pas (si configure comme chaudire) Brancher le capteur de temprature extrieur aux bornes S1/S1. L'appareil n'indique que la temprature extrieure lorsqu'il est configur sur compresseur. Contrler le capteur pour s'assurer qu'il n'y a ni court-circuit ni circuit ouvert. Vrifier que le capteur de temprature extrieure n'est pas directement expos la lumire solaire. Un fil plus long peut tre requis pour assurer une installation adquate. Attendre 5 minutes. Le compresseur se met en marche aprs le dlai de scurit. Contrler le capteur pour vrifier qu'il n'y a pas de court-circuit ni de circuit ouvert, ou installer le capteur de temprature intrieure sur les bornes S1/S1. 15 33-00135EFS03 33-00135EFS_B.book Page 16 Wednesday, November 11, 2015 11:31 AM CARACTRISTIQUES Gamme de temprature ambiante de service :
Compresseur : -40 +68 C (-40 +155 F) Chaudire : -1 +54 C (30 +130 F) Plage d'humidit relative de service : 0 - 99 %
Spcifications lectriques :
24 V c.a., 50/60 Hz. Dimensions :
175 mm x 168 mm x 38 mm Capacit sans fil via technologie RedLink. 6-39/64
(168) 6-7/8 (175) Fig. 15. Dimensions. 1-31/64
(38) M35664 33-00135EFS03 16 33-00135EFS_B.book Page 17 Wednesday, November 11, 2015 11:31 AM PICES SPARABLES ERM avec TH8321R1001/U : YERM5220R8321 ERM avec TH8321R1001/U et THM5421R1021 : YERM5220RVPEIM RGLEMENTS DE LA FCC 15.19 (a)(3) Ce dispositif est conforme la Partie 15 du rglement de la FCC. Le fonctionnement est soumis aux deux conditions suivantes :
1. Ce dispositif ne doit pas causer dinterfrences nuisibles, et 2. Ce dispositif doit accepter toutes les interfrences reues, y compris celles pouvant causer un fonctionnement non souhait. RGLEMENTATION IC RSS-GEN Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. 2. lappareil ne doit pas produire de brouillage;
lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Avertissement de la FCC (Partie 15.21)
(tats-Unis uniqument):
Toute modification qui n'est pas autorise expressment par la partie responsable de la conformite de l'appareil peut rendre l'utilisateur inapte a faire fonctionner l'quipment 17 33-00135EFS03 33-00135EFS_B.book Page 18 Wednesday, November 11, 2015 11:31 AM GARANTIE DE 5 ANS Honeywell garantit ce produit contre tout vice de fabrication ou de matriau dans la mesure o il en est fait une utilisation et un entretien convenables, et ce, pour cinq (5) ans partir de la date dachat par le consommateur. En cas de dfaillance ou de mauvais fonctionnement pendant la priode de garantie, Honeywell remplacera ou rparera le produit ( sa discrtion). Si le produit est dfectueux,
(i) le renvoyer avec la facture ou une autre preuve dachat date au lieu dachat; ou
(ii) appeler le service la clientle de Honeywell en composant le 1-800-468-1502. Le service la clientle dterminera si le produit doit tre retourn ladresse suivante :
Honeywell Return Goods, Dock 4MN10-3860, 1985 Douglas Dr. N., Golden Valley, MN 55422, ou si un produit de remplacement peut tre expdi. La prsente garantie ne couvre pas les frais de retrait ou de rinstallation. La prsente garantie ne sappliquera pas sil est dmontr par Honeywell que la dfaillance est due un endommagement du produit qui s'est produit lorsque le consommateur lavait en sa possession. La responsabilit exclusive de Honeywell se limite rparer ou remplacer le produit conformment aux modalits susmentionnes. HONEYWELL NEST EN AUCUN CAS RESPONSABLE DES PERTES OU DOMMAGES, Y COMPRIS LES DOMMAGES INDIRECTS OU ACCESSOIRES DCOULANT DIRECTEMENT OU INDIRECTEMENT DUNE VIOLATION QUELCONQUE DUNE GARANTIE, EXPRESSE OU TACITE, APPLICABLE AU PRSENT PRODUIT, OU TOUTE AUTRE DFAILLANCE DU PRSENT PRODUIT. Certains tats ou provinces ne permettent pas de limiter la dure des garanties tacites et, par consquent, la prsente limitation peut ne pas sappliquer. CETTE GARANTIE EST LA SEULE GARANTIE EXPRESSE FAITE PAR HONEYWELL POUR CE PRODUIT. LA DURE DE TOUTE GARANTIE IMPLICITE, INCLUANT LES GARANTIES DE QUALIT MARCHANDE OU DADAPTATION UNE UTILISATION PARTICULIRE, EST LIMITE PAR LES PRSENTES LA PRIODE DE CINQ ANS DE LA PRSENTE GARANTIE. Certaines provinces ne permettent pas de limiter la dure des garanties tacites et, par consquent, la prsente limitation peut ne pas sappliquer. La prsente garantie donne au consommateur des droits spcifiques et certains autres droits qui peuvent varier dune province lautre. Pour toute question concernant la prsente garantie, prire dcrire aux Services la clientle de Honeywell ladresse suivante : Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422, ou composer le 1-800-468-1502. 33-00135EFS03 18 33-00135EFS_B.book Page 19 Wednesday, November 11, 2015 11:31 AM 19 33-00135EFS03 33-00135EFS_B.book Page 20 Wednesday, November 11, 2015 11:31 AM Solutions de rgulation et d'automatisation Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 yourhome.honeywell.com Marque de commerce dpose aux tats-Unis 2015 Honeywell International Inc. 33-00135EFS03 M.S. 11-15 Imprim aux tats-Unis 33-00135EFS_B.book Page 1 Wednesday, November 11, 2015 11:31 AM Mdulo de acceso remoto al equipo ERM5220R CON TECNOLOGA INALMBRICA REDLINK GUA DE INSTALACIN ndice 2 Sobre el ERM5220R Lista de verificacin para la instalacin 3 4 Designacin de los terminales:
6 Instalacin Verificacin 12 Localizacin y solucin de problemas 14 Especificaciones 16 Garanta de 5 Aos 19 PRECAUCIN Lea todas las instrucciones de instalacin y cumpla con estas atentamente. La instalacin la debe realizar un tcnico de servicio calificado y debe cumplir con los cdigos locales. Desconecte el suministro de energa elctrica hacia todos los dispositivos relevantes antes de instalar o prestar servicio al ERM. No conectar el dispositivo segn estas instrucciones, puede ocasionar daos al dispositivo, los controles y/o lesiones personales. 33-00135EFS-03 33-00135EFS_B.book Page 2 Wednesday, November 11, 2015 11:31 AM Sobre el ERM5220R TERMOSTATO ERM CALDERA ERM CABLE UNIDAD DE CONDENSACIN MSCR35654 Fig. 1. Comunicacin inalmbrica RedLink entre el unidad de condensacin/compresor o la caldera y el termostato. Elimina la necesidad de pasar cables adicionales a su equipo, por ejemplo, durante una actualizacin de la bomba de calor. Apto para uso exterior. Terminales de sensor de temperatura para proteccin de los sensores de temperatura exteriores o de congelamiento en interiores. Los LED para revisin fcil de la instalacin. Puede disminuir el dao a los hogares debido a que se elimina el cableado/las perforaciones. NOTA: El ERM5220R se deber utilizar con los THX-
9421R5021, TH8321R1001 actualizados y/o con el mdulo de interfaz del equipo (EIM). Busque esta imagen en estos productos. 33-00135EFS03 2 33-00135EFS_B.book Page 3 Wednesday, November 11, 2015 11:31 AM Lista de verificacin para la instalacin MATERIALES PROPORCIONADOS:
ERM5220R Equipment Remote Module WITH REDLINK WIRELESS TECHNOLOGY INSTALL GUIDE Table of Contents About the ERM5220R Installation Checklist Terminal Designations Installation Checkout Troubleshooting Specifications 5 Year Warranty 2 3 4 6 12 14 16 18 CAUTION Read these installation instructions completely and follow them carefully. Installation must be performed by a qualified service technician and must comply with local codes. Disconnect power to all relevant devices before installing or servicing the ERM. Failure to connect the device according to these instructions may result in damage to the device, the controls, and/or personal injury. 33-00135EFS-03 M35671 ERM5220R Tarugos de pared (2) y tornillos de montaje (2) Tornillo para cubierta adicional (opcional) Instrucciones de instalacin HERRAMIENTAS NECESARIAS (NO SE SUMINISTRAN):
M35669 M35672 M35670 Taladro Accesorio de insercin de tuercas para uso con el taladro Pelacables Destornillador pequeo de hoja plana Destornillador de estrella Transformador de 120/240 V a 24 V (opcional) 3 33-00135EFS03 33-00135EFS_B.book Page 4 Wednesday, November 11, 2015 11:31 AM Designacin de los terminales:
1
. I I E L B T A P M O C K N L d e R O T A T S O M R E T L A A D A C N U M O C R E S N C A L E G N O C S E D A L
. I I I R O S E R P M O C L E D N C A L E G N O C S E D E D L A N M R E T I
. R O S E R P M O C L E D O S U L E A R A P R A G U L U S N E R A T S E E B E D R Y J E R T N E E T N E U P L E
. E T N E U P L E D L A N M R E T I
. S A P A T E S O D E D R O S E R P M O C L E D A P A T E A D N U G E S
. S A P A T E S O D E D R O S E R P M O C L E D A P A T E A R E M R P I
. I A C V 4 2 E D N C A T N E M L A A R A P S E L A N M R E T I I
. R O L A C E D A B M O B A L N E A L U V L V A L R T R E V N I I
/
A R A P B O L A N M R E T I
. I I 1 X U A L E R A T N E M L A
"
D
"
L A N M R E T L E N E A D A R T N E A L R A V T C A I
. I N C A L E G N O C S E D A R A P A D A R T N E A N U O M O C A N O C N U F
"
D
"
I I L A N M R E T L E R 0 2 2 5 M R E L E O D N A U C E T N E M A C N A V T C A T S E N C N U F A T S E I I I
. I R 0 2 2 5 M R E L A
"
D
"
L A N M R E T L E E T C E N O C O N
, 1 X U A A
"
D
"
A E S E D E S O N I S 5 5 6 5 3 S M
. R O S E R P M O C N U N O C O S U A R A P O D A R U G F N O C T S E I
. I I E L B T A P M O C K N L d e R O T A T S O M R E T L A A D A C N U M O C R E S A L L A F A L
. I R O S E R P M O C L E D A R E B U T E D A L L A F E D L A N M R E T I S A R U T A R E P M E T S A L R A T C E T E D A R A P R A Z L T U E D E U P E S I I
. I S O M H O K 0 1 E D A R U T A R E P M E T E D R O S N E S L E A R A P S E L A N M R E T I
. I I E L B T A P M O C K N L d e R O T A T S O M R E T N U N E N R A R T S O M E S E U Q S E R O R E T X E I DLS1S1 T O/B T Y2 JRCY 1 Fig. 2. Designacin de los terminales para el compresor. R O S E R P M O C L E A R A P S E L A N M R E T S O L E D N C A N G S E D I I I 33-00135EFS03 4 33-00135EFS_B.book Page 5 Wednesday, November 11, 2015 11:31 AM I I N C A L E G N O C A R T N O C N C C E T O R P A R A P R A Z L T U E D E U P E S I I
. I S O M H O K 0 1 E D A R U T A R E P M E T E D R O S N E S L E A R A P S E L A N M R E T I I I O D A Z L T U R E S A R A P S E R O R E T N I I N E R E C E N A M R E P E B E D R O S N E S L E
. I M R E L A L A E S A L A D R E P O T A T S O M R E T L E E U Q E D O S A C N E
. I N C A L E G N O C A R T N O C N C C E T O R P O M O C I
. I N C C A F E L A C E D A D N A M E D A R A P L A N M R E T I
. I N C C A F E L A C E D A D N A M E D A R A P L A N M R E T I A 6 5 6 5 3 S M
"
Y
"
L E R L E
, A R E D L A C A N U O M O C A R U G F N O C E S O D N A U C I
. I I 0 2 E R E S A L N O C O T N E M A N O C N U F L E E T M D A O N M R E L E I I
. O T N E M O M O D O T N E O D A G A P A R A T S E E B E D
. A R E D L A C A L E D O S U L E A R A P R A G U L U S N E R A T S E E B E D R Y J E R T N E E T N E U P L E
. E T N E U P L E A R A P L A N M R E T I
. I A C V 4 2 E D N C A T N E M L A A R A P S E L A N M R E T I I TDLS1S1 O/B T Y2 JRCY
:
A T O N I A R E D L A C A L A R A P S E L A N M R E T S O L E D N C A N G S E D I I Fig. 3. Designacin de los terminales para la caldera. 5 33-00135EFS03 33-00135EFS_B.book Page 6 Wednesday, November 11, 2015 11:31 AM INSTALACIN IMPORTANTE El mdulo de acceso remoto al equipo (ERM) no es compatible con los tableros de zona RedLink. Para garantizar que el ERM reciba una seal inalmbrica en el lugar de instalacin deseado, siga los pasos 1 al 5 en la seccin de Cableado. Si el lugar tiene paneles de revestimiento de metal, la seal del ERM puede verse afectada. Si no hay comunicacin o la seal tiene poca potencia, considere una ubicacin diferente. Un Prestige (con EIM) o VisionPRO (con o sin EIM) solo permitir una de las siguientes configuraciones:
1) Incorporado con un ERM configurado a una sola caldera;
2) Incorporado con un ERM configurado a un solo compresor;
3) Incorporado con un ERM configurado a una sola caldera e incorporado con un ERM configurado a un solo compresor. Cableado 1. Compruebe que el suministro de energa elctrica hacia el compresor/
caldera est desconectado. 2. Retire la cubierta frontal aflojando el tornillo de la cubierta y extrayndola de la parte inferior del ERM. 3. Retire 3 o 4 pulgadas (7.6 cm o 10.2 cm) del revestimiento del cable, seguidamente retire de 3/8 a 1/2 pulgada del aislante de cada cable. Fig. 4. Cable preparado para el cableado. M35674 33-00135EFS03 6 33-00135EFS_B.book Page 7 Wednesday, November 11, 2015 11:31 AM 4. Para aplicaciones en el compresor: Deje el puente entre los terminales J y R en su lugar. Para aplicaciones en la caldera: Retire el puente entre los terminales J y R. FOR COMPRESSOR:
Jumper J and R FOR BOILER:
Remove Jumper J R C Y Y2 T O/B T D L S1 S1 Fig. 5. Designaciones de terminales mostrando el puente entre los terminales J y R. MCR35657 5. Para compresores y calderas: Conecte a una toma de energa de 24 V CA a los terminales R y C en el ERM. J R C Y Y2 T O/B T D L S1 S1 24 VAC V c.a. LOS 24 V PUEDEN PROCEDER DE UN CONTROLADOR DE AIRE (APLICACIN DEL COMPRESOR) O DE UN TRANSFORMADOR EXTERNO MS35658 Fig. 6. Una vez que se ha conectado el suministro de energa elctrica, el LED del Compresor (o de la Caldera) debe ponerse en verde. (Fig. 7) Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating O Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating MCR35659 MCR35660 Fig. 7. 7 33-00135EFS03 33-00135EFS_B.book Page 8 Wednesday, November 11, 2015 11:31 AM 6. Para compresores y calderas: Coloque el termostato en el modo de conexin seleccionando "aada un dispositivo" del men del instalador. Para obtener informacin ms detallada, consulte el manual del termostato. Una vez que el termostato est en el modo de conexin, presione y suelte rpidamente el botn "Conectar" en el ERM. Cuando el ERM est conectado al sistema, el LED "conectado"
del ERM estar verde fijo y el termostato mostrar "ERM" en su Administrador inalmbrico. (Fig. 8) Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating O Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating MCR35661 MCR35662 Fig. 8. 7. Conecte los terminales del ERM a los terminales adecuados del tablero de control del compresor/caldera. COMPRESOR J R C Y Y2 T O/B T D L S1 S1 24 VAC V c.a. R C Y PANEL DE CONTROL Y2 O/B D L SENSOR DE 10K OHM DE TEMPERATURA EXTERIOR
(OPCIONAL) DEL EQUIPO MS35668 Fig. 9. 33-00135EFS03 8 33-00135EFS_B.book Page 9 Wednesday, November 11, 2015 11:31 AM CALDERA J R C Y Y2 T O/B T D L S1 S1 24 VAC V c.a. T T PANEL DE CONTROL DEL EQUIPO SENSOR DE 10K OHM DE TEMPERATURA INTERIOR
(RECOMENDADO) MS35673 Fig. 10. IMPORTANTE Si el ERM se utiliz previamente con un compresor y ahora se utilizar con una caldera:
1) Desincorpore el ERM en el termostato;
2) Retire el puente en el ERM;
3) Designe calefaccin radiante para el tipo de sistema de calefaccin (ISU 2000) en su termostato Monte el ERM 8. Utilice dos tornillos y tarugos de pared para fijar el ERM a la pared exterior cerca del compresor. La ubicacin debe estar por lo menos a 3 pies (91 cm) por encima del suelo y orientada con las dos salidas de cable hacia abajo. Vea las Figs. 11 y 12. 9 33-00135EFS03 33-00135EFS_B.book Page 10 Wednesday, November 11, 2015 11:31 AM 9. Fije la cubierta y asegrela con el tornillo inferior (Fig. 13). TORNILLOS DE MONTAJE Equipment Remote Module I ERM5000R Compressor Boiler Connected Connect CONNECTED LED STATUS Flashing: Device Connecting Green: Device Connected Red: Not Communicating J R C Y1 Y2 T O/B T D L S1 S1 Compressor:
Jump J and R Boiler:
Remove Jumper R 0 0 0 5 M R E l I e u d o M e t o m e R t n e m p u q E i g n i t c e n n o C e c v e D i
:
d e t c e n n o C e c v e D i i g n h s a F l
:
n e e r G S U T A T S D E L D E T C E N N O C i g n i t a c n u m m o C t o N
:
d e R t c e n n o C r e l i o B d e t c e n n o C r o s s e r p m o C 1 S 1 S L D B
/
O T 2 Y T 1 Y C R J
:
r o s s e r p m o C R d n a J p m u J
:
r e l i o B r e p m u J e v o m e R TDLS1S1 O/B JRCY1Y2 T Remove Jumper Boiler:
Jump J and R Compressor:
Red: Not Communicating Green: Device Connected Flashing: Device Connecting CONNECTED LED STATUS Connect Connected Boiler Compressor Equipment Remote Module I ERM5000R CORRECTA INCORRECTA INCORRECTA MSCR35665 Fig. 11. Orientacin de montaje. MNIMO 1/4 DE PULGADA
(6.3 mm) DE SEPARACIN Fig. 12. Si est montado sobre paneles de revestimiento, deje espacio para que se pueda retirar la cubierta. MS35666 33-00135EFS03 10 33-00135EFS_B.book Page 11 Wednesday, November 11, 2015 11:31 AM M35667 Fig. 13. 11 33-00135EFS03 33-00135EFS_B.book Page 12 Wednesday, November 11, 2015 11:31 AM Verificacin Active el suministro de energa elctrica hacia el sistema. Utilice el termostato para comenzar el ciclo de refrigeracin o calefaccin, probando el ERM. 1. Restituya el suministro de energa elctrica al compresor/caldera as como al sistema RedLink. 2. Eleve/baje el punto de referencia del termostato de zona para iniciar una demanda de calefaccin/refrigeracin. 3. Observe todos los dispositivos de control para garantizar que el funcionamiento y la calefaccin/refrigeracin estn activas. 4. Baje/eleve el punto de referencia del termostato de zona para suspender la demanda de calefaccin/refrigeracin. 5. Si se utiliza el sensor de temperatura exterior, revise el termostato para ver si las lecturas estn activas y son precisas. 6. Verifique que el termostato est en las configuraciones deseadas cuando finalice la revisin. 33-00135EFS03 12 33-00135EFS_B.book Page 13 Wednesday, November 11, 2015 11:31 AM M35680 Fig. 14. 13 33-00135EFS03 33-00135EFS_B.book Page 14 Wednesday, November 11, 2015 11:31 AM LOCALIZACIN Y SOLUCIN DE PROBLEMAS NOTA: Desconecte RedLink cuando haga cambios al dispositivo. PROCEDIMIENTO PARA REINICIAR:
Presione el botn "Connect" (conectar) en el ERM durante 10 segundos. El LED de la "conexin" debe aparecer en rojo durante unos segundos y despus se apaga. Esto indica que la unidad est reiniciada. Sntoma Causa posible Accin Los rels no cambian como se espera Configuracin incorrecta del puente. El LED conectado est rojo Prdida de comunicacin con el sistema El LED conectado est apagado Ninguno de los LED est encendido El dispositivo no est incorporado al sistema No llega electricidad al dispositivo Revise la configuracin del puente. Si est incorrecta, desincorpore a nivel del sistema, cambie el puente y vuelva a incorporar al sistema. Verifique que el termostato y/o el mdulo de acceso remoto estn alimentados y funcionando correctamente. Incorprelo al sistema. Verifique que haya 24 V CA en los terminales R/C 33-00135EFS03 14 33-00135EFS_B.book Page 15 Wednesday, November 11, 2015 11:31 AM Sntoma No se muestra la temperatura exterior en el termostato Causa posible No hay sensor de temperatura de exterior cableado conectado al ERM, ni dispositivo configurado como caldera El termostato muestra para la temperatura exterior La lectura de temperatura exterior del termostato es demasiado alta Falla en el sensor de temperatura cableado exterior Carga de sol en el sensor Bloqueo del compresor durante 5 minutos despus del ciclo de encendido No hay sensor de temperatura vlido en interiores El compresor no se activa, el LED "Y"
est parpadeando El control de respaldo de emergencia no funciona (si se configura como caldera) Accin Conecte el sensor de temperatura exterior a los terminales S1/S1. El dispositivo solo reporta la temperatura exterior cuando est configurado como compresor. Revise el sensor en busca de cortocircuito o circuito abierto. Verifique que el sensor de temperatura exterior no est bajo la luz solar directa. Puede necesitar utilizar un cable ms largo para montarlo en un lugar ideal. Espere 5 minutos, el compresor se activar despus del apagado por seguridad. Revise el sensor en busca de cortocircuito o circuito abierto o instale el sensor de temperatura en interiores en los terminales S1/S1. 15 33-00135EFS03 33-00135EFS_B.book Page 16 Wednesday, November 11, 2015 11:31 AM ESPECIFICACIONES Rango de temperatura ambiente de funcionamiento:
Compresor: De -40 a +155 F (-40 a +68 C) Caldera: De 30 a +130 F (-1 a +54 C) Rango de humedad relativa de funcionamiento: 0 - 99 %
Caractersticas elctricas:
24 V CA, 50/60 Hz. Dimensiones:
175 mm x 168 mm x 38 mm Habilitacin inalmbrica mediante la tecnologa RedLink. 6-39/64
(168) 6-7/8 (175) 1-31/64
(38) M35664 Fig. 15. Dimensiones. 33-00135EFS03 16 33-00135EFS_B.book Page 17 Wednesday, November 11, 2015 11:31 AM PARTES SEPARABLES ERM con TH8321R1001/U: YERM5220R8321 ERM con TH8321R1001/U y THM5421R1021: YERM5220RVPEIM 17 33-00135EFS03 33-00135EFS_B.book Page 18 Wednesday, November 11, 2015 11:31 AM REGULACIONES DE LA FCC 15.19 (a)(3) Este dispositivo cumple con la Seccin 15 de las regulaciones la FCC. El funcionamiento est sujeto a las dos condiciones siguientes:
1. Este dispositivo no debe causar interferencia perjudicial y 2. este dispositivo deber aceptar cualquier interferencia que se reciba, incluyendo la interferencia que pudiese causar el funcionamiento no deseado. REGULACIONES IC RSS-GEN Este dispositivo cumple con la(s) norma(s) RSS exentas de licencia de la industria de Canad. El funcionamiento est sujeto a las dos condiciones siguientes:
1. Este dispositivo no debe causar interferencia, y 2. Este dispositivo deber aceptar cualquier interferencia, incluso la interferencia que pudiese causar el funcionamiento no deseado del dispositivo. Advertencia de la FCC (Seccin15.21)
(solo en los EE.UU.) Los cambios o las modificaciones que no hayan sido expresamente aprobados por la parte responsable del cumplimiento de las regulaciones podran anular la autoridad del usuario para hacer funcionar el equipo. 33-00135EFS03 18 33-00135EFS_B.book Page 19 Wednesday, November 11, 2015 11:31 AM GARANTA DE 5 AOS Honeywell garantiza que este producto no tiene defectos en la mano de obra ni en los materiales en condiciones de uso y servicio normales durante un perodo de cinco (5) aos desde la fecha de compra por parte del consumidor. Si en cualquier momento, durante el perodo de vigencia de la garanta, se determina que el producto est defectuoso o no funciona adecuadamente, Honeywell lo reparar o lo reemplazar (a eleccin de Honeywell). Si el producto est defectuoso,
(i) llvelo al lugar donde lo compr, junto con la factura de compra u otra prueba de compra que incluya la fecha en la que compr el producto; o
(ii) comunquese con el Servicio de atencin al cliente de Honeywell, llamando al 1-
800-468-1502. En el Servicio de atencin al cliente determinarn si el producto debe ser devuelto a la siguiente direccin: Honeywell Return Goods, Dock 4 MN10-3860, 1985 Douglas Dr. N., Golden Valley, MN 55422, o si se le puede enviar un producto de reemplazo. Esta garanta no cubre los gastos de remocin ni de reinstalacin. Esta garanta no se aplicar si Honeywell demuestra que el defecto fue causado por daos que se produjeron mientras el producto estuvo en posesin de un consumidor. La nica responsabilidad de Honeywell ser la de reparar o reemplazar el producto dentro de los trminos mencionados anteriormente. HONEYWELL NO SER RESPONSABLE POR LA PRDIDA NI EL DAO DE NINGN TIPO, QUE INCLUYE CUALQUIER DAO INCIDENTAL O CONSECUENTE QUE RESULTE, DIRECTA O INDIRECTAMENTE, DE CUALQUIER INCUMPLIMIENTO DE CUALQUIER GARANTA, EXPRESA O IMPLCITA, O DE CUALQUIER OTRA FALLA DE ESTE PRODUCTO. Algunos estados no permiten la exclusin o limitacin de los daos incidentales o consecuentes, por lo que esta limitacin podra no aplicarse en su caso. ESTA GARANTA ES LA NICA GARANTA EXPRESA QUE HONEYWELL REALIZA SOBRE ESTE PRODUCTO. LA DURACIN DE CUALQUIERA DE LAS GARANTAS IMPLCITAS, INCLUYENDO LAS GARANTAS DE COMERCIABILIDAD O DE APTITUD PARA UN FIN DETERMINADO, ESTN LIMITADAS A LOS CINCO AOS DE DURACIN DE ESTA GARANTA. Algunos estados no permiten limitaciones en relacin a la duracin de una garanta implcita, de manera tal que la limitacin anterior puede no aplicarse en su caso. Esta garanta le otorga derechos legales especficos, pero es posible que usted goce de otros derechos que varan de un estado a otro. Si tiene preguntas acerca de esta garanta, escriba a Honeywell Customer Relations, 1985 Douglas Dr. Golden Valley, MN 55422 o llame al 1-800-468-1502. 19 33-00135EFS03 33-00135EFS_B.book Page 20 Wednesday, November 11, 2015 11:31 AM Automatizacin y control desenlace Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 yourhome.honeywell.com Marca Registrada en los Estados Unidos 2015 Honeywell International Inc. 33-00135EFS03 M.S. 11-15 Impreso en Estados Unidos
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2016-01-04 | 903 ~ 926.4 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2016-01-04
|
||||
1 | Applicant's complete, legal business name |
Ademco Inc
|
||||
1 | FCC Registration Number (FRN) |
0004788345
|
||||
1 | Physical Address |
1985 Douglas Drive
|
||||
1 |
Golden Valley, Minnesota 55422-3922
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
g******@nwemc.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
HS9
|
||||
1 | Equipment Product Code |
ERM5220R01
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
P******** W********
|
||||
1 | Title |
Sr. Compliance Engr
|
||||
1 | Telephone Number |
763-9********
|
||||
1 | Fax Number |
763-9********
|
||||
1 |
P******@Honeywell.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | ERM5220R01 | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power is conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter within a host device, except in accordance with FCC multi-transmitter product procedures. Installers and end-users must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Northwest EMC, Inc.
|
||||
1 | Name |
G****** K********
|
||||
1 | Telephone Number |
503-8********
|
||||
1 | Fax Number |
503-8********
|
||||
1 |
g******@nwemc.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 903.00000000 | 926.40000000 | 0.0100000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC