Controller Kit Installation Manual MIFH1, MRCH1, MCCH1, MOS1 Installation guide for:
Wireless Receiver and Cable (MIFH1) Remote Controller (MRCH1) Portable Central Controller (MCCH1) Outdoor Air Sensor (MOS1) DISCONNECT POWER BEFORE BEGINNING INSTALLATION. Can cause electrical shock or equipment damage. Must be installed by a trained, experienced technician. Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition. Installation at a glance Remote controller Wireless receiver Wireless outdoor air sensor This document covers linking and installation procedures for the Mitsubishi Split-Zoning Ductless and Ducted Systems' RedLINK control devices and accessories. Portable central controller M32309 Before you begin, you must attach the cable to the CN105 connector on the indoor unit control board, then follow the steps in this document. Remote controllers are linked to specific indoor units. Each indoor unit must have a dedicated remote controller and wireless receiver. 2010 Mitsubishi Electric & Electronics USA, Inc. Suwanee, GA 30024 All Rights Reserved. The three diamond logo is a registered trademark of Mitsubishi Electric Corporation www.mitsubishipro.com 69-2426-01 Wireless System Installation Guide 1 Install batteries in wireless devices Install batteries in all devices. Make sure batteries are inserted properly (see polarity marks on the devices). Remote Controller Install 2 fresh AA batteries Install quick reference card M28472A M28474 Portable Central Controller (optional): Install 3 fresh AA batteries Outdoor air sensor (optional): Install 2 fresh AA lithium batteries 2 Install cable and receiver 1 Before mounting indoor unit, connect cable to the 5-pin CN105 connector on the control board in the indoor unit. 2 Mount indoor unit. Route cable to preferred location of the wireless receiver. 3 Route cable through hole in base of wireless receiver and attach to 5 pin connector on receiver board. 4 Push the excess cable back through the indoor unit or behind the wireless receiver. Do not cut or modify the cable. Use zip tie connections on back of receiver if needed. 5 Mount wireless receiver next to the indoor unit
(see below) or in a remote location. Mount in the orientations shown. Do not block vents. X OR X 69-242601 2 OR MCR31400 3 Link all devices to wireless network 1 Remove cover from wireless receiver. 2 Verify POWER light is solid green. 3 Press and release the CONNECT button. 4 If CONNECT light does not flash, another receiver or RedLINK wireless adapter may be in wireless setup mode. Exit wireless setup at the other device. POWER LED Solid Green: Powered and communication CONNECT LED Flashing Green: In wireless setup is established. mode. Slow Flashing Green (1 flash/
second): Receiver is powered. Wait approximately 30 seconds for communication to be established between the wireless receiver and the indoor unit. Check cable connection if flashing does not stop after 30 seconds. Fast Flashing Green (5 flashes/second):
Error in communication between wireless receiver and the indoor unit. Check cable connection. Solid Green: RedLINK communication is established. Yellow: Please wait. Red: RedLINK device is not communicating. Flashing status light times out after 15 minutes of inactivity. Press CONNECT again if necessary. Link remote controller to wireless network Zone name Press s or t to change the name or location of this zone, then press NEXT. Wireless Setup Example: 67 = Meeting Room Next M28925 See complete zone list on page 8. Press CONNECT to establish a link to the wireless network. If E0 or E1 appears, see error codes on page 10. Wireless Setup Back Connect M32308 Connected Wireless Setup Done After a brief pause, the confirmation screen at left should be displayed to verify that the wireless connection has been established. Press DONE to display the home screen. M32307 3 69-242601 Wireless System Installation Guide Link Portable Central Controller to RedLINK network (optional) CONNECT 1 Make sure the CONNECT light on the wireless receiver is flashing. 2 Press CONNECT at the Portable Central Controller. There will be a short delay as the Portable Central Controller seeks a signal from the wireless network. WIRELESS SETUP 3 When the screen displays "Connected,"
M28481 Press to link another receiver Press to save and exit YES NO CONNECT MORE?
M28482 press DONE. 4 Press NO at the next screen to save and exit.
(Or press YES and repeat steps 1-4 to link another receiver.) If E1 appears, see error codes on page 10. The linking procedure may time out if there is no keypress within 15 minutes. To begin again, press and hold the blank space (or arrow, if present) in the lower right corner of the screen until the display changes (about 3 seconds). Link outdoor sensor to RedLINK network (optional) Press and release 1 Make sure the CONNECT light on the wireless receiver is flashing. 2 Press and release the CONNECT button on the back of the sensor. 3 Check remote controller to verify that the outdoor sensor is working. After about 15 seconds, the remote controller should display outdoor temperature and humidity. 69-242601 M28483 4 Exit wireless setup Press and release the CONNECT button at the wireless receiver to exit wireless setup (light should stop flashing and remain solid). Replace cover on wireless receiver. Note: The wireless receiver will automatically exit wireless setup after 15 minutes of inactivity. Note: If installing more than one receiver, you must exit wireless setup before installing remote controller and additional receiver. 4 Customize remote controller (installer setup) Follow the steps below to begin installer setup. At each function screen, press s or t to change the setting as desired, then press NEXT to advance to the next function screen. See tables on pages 6-8 for a description of options for each function. To begin, press and hold the FAN and s buttons until the display changes. "WAIT"
will be displayed for up to 40 seconds. Fan Function Setting M289871 Press s or t to change setting (see tables on pages 6-8). Done Back Next M28927 Press DONE to save & exit. Press NEXT to display next function screen. M28488A 5 69-242601 Wireless System Installation Guide Installer setup tables Default settings for Setup functions 101-128 are automatically determined by the HVAC equipment. It may take up to 40 seconds to enter setup, and 30 seconds to exit setup. only) Installed operation 103 Ventilation Air 104 Power Voltage 105 Auto energy-savings 107 Change Filter Duration 109 No. of Air Outlets (PLA 110 High Performance Filter restarts after power outage Setup function 101 Unit automatically Settings & options (factory default in bold) 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 108 Auto Fan (speed setting) 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 OFF ON Not Supported Not Supported IDU does not intake outdoor air through LOSSNAY IDU does intake outdoor air through LOSSNAY 230V 208V Not Supported ON OFF Not Supported 100 Hours 2500 Hours OFF Quiet Standard High Ceiling 4 directions 3 directions 2 directions NO YES Not Supported No Vanes (or Vane #3 for PLA) Vane #1 Setting (typically kept at the default setting) Vane #2 Setting (typically kept at the default setting) 36 F (2 C) 37 F (3 C) Not Supported Standard High Humidity Not Supported Not Available Available Not Supported ON OFF Not Supported Extra Low Stop Selectable Fan Speed Selectable Fan Speed Stop Not Supported ON OFF Not Supported Indoor Unit Coil Frost Prevention Temperature 123 Airflow Oscillate Mode 128 Display System Error 111 Airflow Direction 127 Thermal Off Fan 125 Thermal Off Fan Operation (Heat Mode) Operation (Cool Mode) 117 Defrost Control 124 Heating Mode Temperature Offset Settings 115 69-242601 6 Installer setup tables Setup function 134 Central Controller
(AG-150 or similar) Present Settings & options (factory default in bold) 0 1 Not Installed Installed 139 140 Commercial Override 138 Permanent Hold Lock
(Non-programmable) Fahrenheit/Celsius Display 136 Residential/Commercial 1 0 0 1 0 1 3 0 112 0 1 1 0 2 3 144 System Changeover 142 System Type Duration 145 System Changeover Deadband Value 146 Drying Mode 148 Schedule Format 150 Optimal Start 152 Scheduled Off 154 Power Off Timer
("Sleep Timer") 160 Full Lockout 162 Lockout On/Off 164 165 Lockout System Mode
(Heat, Cool, Auto, Drying) Lockout Fan Mode 166 Lockout Setpoint 168 Lockout Set Clock/Day/
Schedule 170 Max Heat Setpoint 172 Min Cool Setpoint 173 Sensing Location 174 Indoor Temperature Display Offset 3 28 0 1 0 1 1 0 0 1 0 1 2 0 1 0 1 0 1 0 1 0 1 0 1 90 4089 50 5199 1 0 0 Commercial Residential OFF (Programmable) ON (Non-programmable) Fahrenheit Celsius 3 Hours OFF 112 Hours Heat & Cool (Heat Pump) Cool Only System Changeover (Auto, Heat, Off, Cool) Manual Changeover (Heat, Off, Cool) System Changeover Only (Auto Only) System Changeover Single Setpoint - only with AG-150 or similar (Auto, Heat, Off, Cool) 3 F (2 C) 28 F (1.54.5 C) OFF ON 5-2 5-1-1 ON OFF Not Shown Shown Not Shown Resume operation at next scheduled period Permanently Off until user changes System mode No Yes No Yes No Yes
* See page 9 for feature information No Yes No Yes No Yes 90 F (32 C) 40 to 89 F (4.5 to 31.5 C) HVAC Equipment 50 F (10 C) 51 to 99 F (10.5 to 37 C) HVAC Equipment Sense at Remote Controller Sense at Indoor Unit 0 F (0 C)
-3 to 3 F (-1.5 to 1.5 C)
* Subject to
* Subject to 7 69-242601 Wireless System Installation Guide Installer setup tables Setup function 176 Outdoor Temperature Display Offset 178 Outdoor Humidity Display Offset 192 Zone Name 194 Wireless Setup 198 Reset Schedule to Factory Defaults 199 Reset Installer Setup to Factory Defaults 3 0 1 2 4 5 6 52 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 1 0 0 1 0 1 Settings & options (factory default in bold) 0 NURSERY OFFICE OFFICE 1 OFFICE 2 PANTRY PLAYROOM POOL ROOM PORCH REC ROOM SEWING ROOM SPA STORAGE ROOM STUDIO SUN ROOM THEATER THERMOSTAT UPPER LEVEL UTILITY ROOM 0 F (0 C)
-5 to 5 F (-2.5 to 2.5 C) 0%
-15%
-10%
-5%
5%
10%
15%
THERMOSTAT BASEMENT BATHROOM BATHROOM 1 BATHROOM 2 BATHROOM 3 BEDROOM BEDROOM 1 BEDROOM 2 BEDROOM 3 BEDROOM 4 BOAT HOUSE BONUS ROOM COMPUTER ROOM DEN DINING ROOM EXERCISE ROOM FAMILY ROOM FIREPLACE FOYER GAME ROOM GARAGE GREAT ROOM GUEST ROOM GYM KIDS ROOM KITCHEN KITCHEN 1 KITCHEN 2 LAUNDRY ROOM LIBRARY LIVING ROOM LOWER LEVEL MASTER BATH Remote controller is connected to wireless system Disconnect Remote controller from wireless system No Yes No Yes 34 MASTER BED 35 MEDIA ROOM 36 MUSIC ROOM 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 WALK IN CLOSET 56 WINE CELLAR 57 WORKSHOP Commercial Names 64 CONFERENCE RM 65 DRESSING ROOM 66 MACHINE ROOM 67 MEETING ROOM 68 69 70 71 72 OPEN AREA 1 OPEN AREA 2 SERVER 1 SERVER 2 STOCK ROOM 69-242601 8 Special functions Commercial Override (Setup Function 140): Allows an employee during an unoccupied period to temporarily activate an occupied temperature. Each press of HOLD extends the occupied temperature out 1 hour (or as installed). Optimal Start (Setup Function 150): Allows the remote controller to learn how long the equipment will take to reach programmed temperature settings, so the temperature is reached at the scheduled time. Scheduled Off (Setup Function 152): Allows the user to schedule a period where the split-zoning system is completely off and resumes operation at the next scheduled period. Power Off Timer (Setup Function 154): Allows user to schedule indoor unit completely off for one instance:
Follow Schedule Option: indoor unit will resume operation at the next scheduled period. Permanently Off Option: indoor unit will remain off indefinitely until the user changes the system mode. Installer test Follow the procedure below to test for proper operation. System test number System status Press s or t to check system status Press NEXT to advance to next test M32306 Press DONE to terminate system test Next Done To begin, press and hold the s and t buttons until the display changes (about 3 seconds). M28488A Back System test System status 02 Wireless test 0 1 Off Test radio signal (after a brief pause, screen displays 5-10 to show signal strength; 5 or higher recommended) Off Cool Heat 50 Cool/Heat test 70 Configuration Data 1
(remote controller) 80 Configuration Data 2
(remote controller) 90 Configuration Data 1
(wireless receiver) 95 Configuration Data 2
(wireless receiver) 0 1 2 71 Software revision number (major revisions) 72 Software revision number (minor revisions) 73 Configuration identification code (major) 74 Configuration identification code (minor) 75 Production configuration date code (week) 76 Production configuration date code (year) 81 Software revision number (major revisions) 82 Software revision number (minor revisions) 83 Software revision number (build revisions) 91 Software revision number (major revisions) 92 Software revision number (minor revisions) 93 Software revision number (build revisions) 95 Software revision number (major revisions) 96 Software revision number (minor revisions) 97 Software revision number (build revisions) 9 69-242601 Wireless System Installation Guide 5 Mount remote controller & outdoor sensor 1 Separate the wallplate from the remote controller. 2 Mount the wallplate using the included screws and anchors 5 feet from the floor on an interior wall. If the remote controller is configured to sense indoor temperature, mount in the same room as the indoor unit. Drill 3/16" holes for drywall. Drill 7/32" holes for plaster. 3 Snap the remote controller to the wallplate on the wall. Outdoor sensor (optional) Mount the sensor on a vertical exterior wall, at least 6 inches below any overhang. Choose a location protected from direct sunlight. Place sensor securely in bracket, facing away from wall. M28491 M28492 RedLINK error codes E0 27 Verify device temperature is within operating range. If within range for at least 30 minutes and problem persists, replace Remote Controller. E0 91 Communication was established between wireless receiver and the indoor unit, but communication has been lost for 10 minutes. Check cable connection. Try replacing the cable. E1 29 Attempting to connect incompatible wireless devices. E1 34 Low signal strength. Move wireless device to a different location and try again. E1 38 Make sure Connect light on wireless receiver is flashing and you are 2+ feet away from wireless receiver. E1 54 Indoor unit does not support wireless receiver. For full list of error codes, please refer to your equipment's technical service manual. 69-242601 10 Replacing system components Note: Only use Mitsubishi Electric components or other designated components for installation. Failure to comply may damage the product or cause a hazardous condition. Remote Controller To replace a remote controller, install batteries and follow the procedures on page 3 to link it to the wireless network. If necessary, modify settings as needed (see tables on pages 68). Portable Central Controller & outdoor sensor To replace a Portable Central Controller or outdoor air sensor, install batteries and follow the procedures on page 4 to link it to the wireless network. Wireless receiver After installing a new wireless receiver, you must re-set the remote controller and Portable Central Controller to communicate with the new equipment, as described below. At the remote controller:
1 Press and hold the FAN and s buttons for 3 seconds until display changes.
"WAIT" will be displayed for up to 17 seconds. 2 Press NEXT until Function 194 is displayed (wireless setup). 3 Press t to change Function 194 setting to 0 (disconnect from old wireless receiver). 4 Follow the procedures on page 3 to link to new wireless receiver. At the Portable Central Controller:
1 Press and hold the blank space (or arrow if present) in the lower right corner of the screen until the display changes (about 3 seconds). 2 Press REMOVE, then YES to disconnect from old wireless receiver. 3 Follow the procedure on page 4 to link to new wireless receiver. Removing all wireless devices:
1 Press and hold the CONNECT button on the wireless receiver for 10 seconds. 2 To reconnect, see procedure on page 3. 11 69-242601 Regulatory information FCC Compliance Statement (Part 15.19) (USA only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation. FCC Warning (Part 15.21) (USA only) Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Interference Statement (Part 15.105 (b)) (USA only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Increase the separation between the equipment and receiver. Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Wireless receiver, remote controller and outdoor sensor To comply with FCC and Industry Canada RF exposure limits for general population/ uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Portable Central Controller This portable transmitter with its antenna complies with FCC and Industry Canada RF exposure limits for general population/
uncontrolled exposure. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Section 7.1.5 of RSS-GEN Operation is subject to the following two conditions:
this device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device. 1 2 Specifications & replacement parts Operating Ambient Temperature Remote Controller: 32 to 120 F (0 to 48.9 C) Portable Central Controller: 32 to 120 F (0 to 48.9 C) Wireless receiver: -40 to 165 F (-40 to 73.9 C) Outdoor air sensor: -40 to 140 F (-40 to 60 C) Accessories & Replacement Parts Item Portable Central Controller Outdoor air sensor Remote Controller Receiver and Cable Cable Part Number MCCH1 MOS1 MRCH1 MIFH1 MRC1 Operating Relative Humidity Remote Controller: 5% to 90% (non-
condensing) condensing) Portable Central Controller: 5% to 90% (non-
Wireless receiver: 5% to 95% (non-condensing) Outdoor air sensor: 0% to 100% (condensing) Physical Dimensions (height, width, depth) Remote Controller: 3-9/16 x 5-13/16 x 1-1/2 inches (91 x 147 x 38 mm) Wireless receiver: 6-7/16 x 3-1/4 x 1-5/16 inches (164 x 82.5 x 34 mm) Outdoor air sensor: 5 x 3-1/2 x 1-11/16 inches
(127 x 89 x 43 mm) Portable Central Controller: 6-1/4 x 3-1/8 x 1-5/8 inches (158.2 x 79.9 x 42 mm) 2010 Mitsubishi Electric & Electronics USA, Inc. Suwanee, GA 30024 All Rights Reserved. The three diamond logo is a registered trademark of Mitsubishi Electric Corporation 69-242601 M.S. 11-10 Printed in U.S.A.