all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
manual | Users Manual | 2.80 MiB | September 04 2012 / October 04 2012 | |||
1 | ID Label/Location Info | September 04 2012 / October 04 2012 | ||||||
1 | RF Exposure Info | September 04 2012 / October 04 2012 | ||||||
1 | Cover Letter(s) | September 04 2012 / October 04 2012 | ||||||
1 | Cover Letter(s) | September 04 2012 / October 04 2012 | ||||||
1 | External Photos | September 04 2012 / October 04 2012 | ||||||
1 | Internal Photos | September 04 2012 / October 04 2012 | ||||||
1 | Test Report | September 04 2012 / October 04 2012 | ||||||
1 | Test Setup Photos | September 04 2012 / October 04 2012 |
1 | manual | Users Manual | 2.80 MiB | September 04 2012 / October 04 2012 |
System Installation Guide ComfortNet CTK03 Communicating Thermostat With wireless accessories Modulating control for up to 4 Heat/2 Cool communicating heat pump systems or up to 3 Heat/2 Cool communicating gas heat, electric cooling systems for residential and commercial applications. Installation guide for:
ComfortNet CTK03 Communicating Thermostat Portable Comfort Control Wireless Outdoor Sensor Quick start guide Wireless Indoor Sensor RedLINK Internet Gateway Entry/Exit Remote Vent Boost Remote 1 Install thermostat ..........................................................page 4 2 Power optional accessories ...................................................7 3 Setup thermostat ...................................................................8 4 Link optional accessories ......................................................9 5 Mount optional accessories .................................................11 6 Installer options ...................................................................12 ComfortNet User Menu ....................................................13 Wiring guides .......................................................................19 Key features ....................................................................20-26 Device replacement and specifications ..........................26-27 DISCONNECT POWER BEFORE INSTALLATION. Can cause electrical shock or equipment damage. MERCURY NOTICE: If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact the Thermostat Recycling Corporation at www.thermostat-recycle.org or 800-238-8192 for information on how and where to properly and safely dispose of your old thermostat. Must be installed by a trained, experienced technician. Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition. 69-2688-01 I/O-CHTSTAT03 System Installation Guide The ComfortNet advantage The premium Honeywell ComfortNet control system is easy to use, energy-
efficient, reliable and ensures the system is set up properly. Advanced operating algorithms built into the control delivers efficient equipment operation while pro-
viding optimal comfort. The Honeywell ComfortNet Communicating thermostat is designed to regulate and communicate with the central heating and cooling equipment and has the ability to share information so the user will enjoy efficient, economical comfort throughout the home. RedLINK Compatible Increase your content and profit per job by including Honeywell RedLINK accessories that meet your customers comfort and convenience needs. RedLINK accessories include the Wireless Outdoor Sensor, Portable Comfort Control
(PCC), RedLINK Internet Gateway, Wireless Indoor Sensor, TrueSTEAM humidi-
fier with Wireless Adapter, Vent Boost Remote and Entry/Exit Remote. Customizable Service Reminders Set up to 10 service reminders. Choose from the pre-set options or customize your own. Reminders based on date, outdoor temperature or a dry contact input will alert customers with instructions to contact you for assistance. User Interactions Log The interaction log stores history of thermostat setting changes including tem-
perature, system and installer setup. You can use the interaction log to save time by determining if the issue is a system error or an accidental user error. Configurable for Residential and Light Commercial Applications One thermostat does it all to meet the needs of Residential and Light Commercial applications. Simply select Residential or Commercial during the installer setup. If Commercial is selected, the thermostat will use commercial language, meet building codes and offer 365 day holiday scheduling. USB Port for Quick Installer Setup Save time by using a USB stick to upload installer settings and service reminders in one simple step. Selectable Sensors When paired with a Wireless Indoor Sensor(s) you have the ability to choose which sensor(s) to use for temperature, humidification and dehumidification. They can be used in combination for temperature averagingor individuallyto condi-
tion humidity levels in separate spaces. 69-268801 I/O-CHTSTAT03 2 CTK03 ComfortNet Communicating Thermostat Installation This booklet contains installation instructions and information on the thermostat and wireless accessories. Separate installation instructions for the furnace or air handler and outdoor AC condensing unit or heat pump are provided with the appropriate equipment. This thermostat is designed exclusively for use with the ComfortNet communicating system. Valid System Configurations This control may only be used with certain system configurations. Valid system configurations for which this control can be used are:
A communicating air handler matched with a communicating outdoor AC condensing unit. A communicating air handler matched with a communicating outdoor heat pump unit. A communicating furnace matched with a communicating outdoor AC condensing unit. A communicating furnace matched with a communicating outdoor heat pump unit. A communicating furnace matched with a non-communicating single stage AC condensing unit. Installing Thermostat 1 REMOVE AND INVENTORY ALL COMFORTNET COMPONENTS 2 INSTALL HVAC COMPONENTS 3 REMOVE 9-PIN CONNECTOR FROM FURNACE OR AIR HANDLER CONTROL AIR HANDLER GAS FURNACE P/N F 0 4 3 0 6 7 3 0 0 5 NOTE: CONTAINS THE CTK03 THERMOSTAT, LITHIUM COIN CELL BATTERY, WALL MOUNTING SCREWS AND ANCHORS, SYSTEM INSTALLATION GUIDE, OPERATING MANUAL, AT120A1004 TRANSFORMER WITH MOUNTING HARDWARE AND A WIRING SET THAT INCLUDES TWO TERMINAL BLOCKS AND WIRES. AIR CONDITIONER OR HEAT PUMP AIR CONDITIONER OR HEAT PUMP 5 CONNECT TO THE OUTDOOR UNIT 2-WIRE/TRANSFORMER CONNECTION 4 REMOVE OUTDOOR UNIT COVER AND 7-PIN CONNECTOR P/N F 0 4 3 0 6 7 5 0 0 5 CONNECT 4-WIRES FROM STAT AND 2 OR 4 WIRES FROM OUTDOOR UNIT P/N F0430679005 TERMINALS 1 & 2 ARE COMMUNICATIONS WIRES. THEY SHOULD NEVER BE CONNECTED TO THE 24 VAC R&C POWER SUPPLY TERMINALS. 6 INSTALL THERMOSTAT ON INTERIOR WALL CONNECT 2-WIRES TO INDOOR UNIT HIGH VOLTAGE LOW (24 VAC) VOLTAGE TRANSFORMER LOW VOLTAGE CONNECTED TO R AND C TERMINALS TRANSFORMER
(AT120A1004) CONNECT HIGH VOLTAGE TRANSFORMER LEADS TO L1 AND L2 MALE SPADE TERMINALS ON CIRCUIT BOARD. DO NOT CONNECT R AND C BETWEEN THE INDOOR UNIT AND OUTDOOR UNIT. SEE PAGE 5. NOTE: THERMOSTAT WILL AUTOMATICALLY CONFIGURE TO THE SYSTEM ONCE HIGH VOLTAGE POWER IS APPLIED TO THE INDOOR AND OUTDOOR EQUIPMENT. M33174 1. Remove and inventory all ComfortNet components. The box contains the ComfortNet CTK03 communicating thermostat, lithium coin cell battery, wall mounting screws and anchors, sys-
tem installation guide, operating manual, AT120A1004 transformer with mounting hardware and a wiring set that includes two terminal blocks and wires. 2. Carefully separate the thermostat body from the thermostat base. 3. Place base at installation location and mark mounting hole locations on wall using base as a template. 4. Drill mounting holes. 5. Attach base firmly to wall using two mounting screws. Leveling is for appearance only and will not affect thermostat operation. 6. Connect wires to terminal block on base. 7. 8. Push excess wire into wall and plug hole with a fire resistant material (such as fiberglass 18 AWG solid wire is recommended. insulation) to prevent drafts from affecting thermostat operation. Insert coin cell battery in the back of the thermostat. 9. 10. Carefully line up the thermostat with the base and snap into place. 3 I/O-CHTSTAT03 69-268801 System Installation Guide 1 Install thermostat Thermostat Mounting Mount the thermostat approximately 5 feet from the floor on an interior wall using the included screws and anchors. Drill 3/16" holes for drywall and 7/32" holes for plaster. Do not install the thermostat where it can be affected by:
Drafts or dead spots behind doors and in corners. Hot or cold air from ducts. Radiant heat from sun or appliances. Concealed pipes and chimneys. Unheated (uncooled) areas such as an outside wall. Terminal Functions:
1 - Data 1 2 - Data 2 R - 24 volt power C - 24 volt common Wire Gauge:
18 gauge wire is recommended. Maximum wire distance between the ComfortNet thermostat and the IFC should not exceed 100 feet using 18 gauge wire. 1 2 R C MCR29241 MCR33170 1 2 R C MCR33171 69-268801 I/O-CHTSTAT03 4 CTK03 ComfortNet Communicating Thermostat 1 Install thermostat Wiring Thermostat, Indoor Unit and Outdoor Unit Wire Thermostat to Indoor Unit Connect 1, 2, R and C from the thermostat to 1, 2, R and C at the Indoor Unit. Wire Outdoor Unit Connect wires 1 and 2 from the Indoor Unit to 1 and 2 at the Outdoor Unit. Install the transformer provided and connect to R and C at the Outdoor Unit. Do NOT connect R and C between the Indoor Unit and Outdoor Unit. See below. Note: DIP switch #13 on the equipment needs to be set to OFF. Default setting is OFF. INDOOR BOARD TERMINAL CONNECTIONS DATA 1 DATA 2 24VAC (HOT) 24VAC
(COMMON) 1 2 R C CTK03 1 2 R C OUTDOOR BOARD TERMINAL CONNECTIONS 1 2 R C L1 L2 OUTDOOR TRANSFORMER 24VAC 230V M33168 5 I/O-CHTSTAT03 69-268801 System Installation Guide 2 Power optional accessories
[If no wireless accessories are used, skip to Section 3.]
Outdoor air sensor Indoor air sensor Portable Comfort Control MCR32937 Install 2 fresh AA lithium batteries RedLINK Internet Gateway MCR32938 Install 2 fresh AAA alkaline batteries MCR32939 Install 3 fresh AA alkaline batteries The Honeywell RedLINK Internet Gateway gives your customers remote access to home climate-control systems from any location with Internet access. Using a Web browser, users can review and adjust indoor temperature, system mode and other settings. The Gateway can also send alerts to as many as 6 email addresses if a problem occurs. Connect RedLINK Gateway to a router or modem with Ethernet cable (RJ45). Connect power cord to an electrical outlet not controlled by a wall switch M32940 69-268801 I/O-CHTSTAT03 6 CTK03 ComfortNet Communicating Thermostat 2 Power optional accessories TrueSTEAM Connect the ABCD terminals between TrueSTEAM and the THM4000 Wireless Adapter. Adjust the DIP Switches on TrueSTEAM as follows when using the Wireless Adapter:
DIP3: UP DIP4: UP DIP5: DOWN THM4000R1000 TrueSTEAM Entry/Exit Remote or Vent Boost Remote 1 Remove the cover. 2 Insert the CR2450 coin cell battery (included) into the slot at the bottom of the remote. See polarity marking on the remote. 3 The LED will briefly flash green. If it flashes red, battery is not good. 1 2 3 4 5 6 ON OFF MCR31476 MCR33269 7 I/O-CHTSTAT03 69-268801 System Installation Guide 3 Setup thermostat Initial Power Up 1 Turn on AC power to the system. 2 Select Language. Press Next. 3 Select Application (Residential or Commercial). Press Next. 4 Enter a Device Name. Press Next. The thermostat will automatically iden-
tify the ComfortNet communicating equipment installed and then you will be prompted to add RedLINK acces-
sories (page 9) and setup the Installer Options (page 12). 69-268801 I/O-CHTSTAT03 8 CTK03 ComfortNet Communicating Thermostat 4 Link optional accessories to wireless network If you need to return to the "Add Device" screen to add devices later, press MENU and scroll down to press INSTALLER OPTIONS. Enter the date code (password) when prompted. The date code is printed on the back of the thermostat; or press MENU > EQUIPMENT STATUS to find the date code. After you enter the password, scroll down to press WIRELESS DEVICE MANAGER and then select ADD DEVICE. While the Add Device screen is displayed on the thermostat, press and release the CONNECT button on each wireless device, as described below. Accessories need to be at least 2 feet away from the thermostat during the linking process. Press DONE after all devices have been linked Wireless outdoor sensor Wireless indoor sensor MCR28847A Press and release CONNECT. After a short delay the thermostat will display "Wireless Outdoor Sensor added" on the Add Device screen. MCR32934 MCR32935 Press and release CONNECT. After a short delay, the status light will glow green for 15 seconds. If the status light turns red, the sensor did not link with the thermostat. In normal operation, this light remains off. If it begins flashing red, batteries are low (power will be depleted after 2-3 weeks). When power is interrupted, the equipment and the RedLINK accessories will automatically restore communication after power resumes. If you have both a wired and wireless outdoor sensor installed, the thermostat displays the reading from the wireless outdoor sensor. 9 I/O-CHTSTAT03 69-268801 System Installation Guide 4 Link optional accessories to wireless network Portable Comfort Control Press CONNECT on the Portable Comfort Control display screen. Press DONE when the screen displays "Connected." Press NO at the next screen to save and exit. (Or press YES to link another thermostat.) CONNECT Error messages:
WIRELESS SETUP MCR32942 E1 29 E1 34 E1 38 Incompatible device cannot be connected. Low RF signal. Move device to a different location and try again. Make sure the thermostat is in Wireless Setup mode, and the Portable Comfort Control is at least 2 feet away (600 mm). The linking procedure will time out if there is no keypress for 30 minutes. To begin again, press and hold in the lower right corner of the screen until the display changes (about 3 seconds). RedLINK Internet Gateway Press and release the button on the bottom of the Internet Gateway. After a short delay, the RedLINK status light will glow steady green. The Internet Gateway must be registered online before use at www.mytotalconnectcomfort.com. Enter the MAC ID and MAC CRC numbers located on the bottom of the Internet Gateway. For additional information, see instructions provided with the device. MCR32943 TrueSTEAM Press and release the CONNECT button on the THM4000 Wireless Adapter. After a short delay, the CONNECTED status light will glow steady green.. Entry/Exit Remote or Vent Boost Remote Press and release CONNECT button. After a short delay, the status light will glow green for 15 seconds. If the status light turns red, the remote did not link with the thermostat for the connection process. 69-268801 I/O-CHTSTAT03 MCR33096 10 CTK03 ComfortNet Communicating Thermostat 5 Mount optional accessories
[If no sensors are used, skip to Section 6.]
To install outdoor air sensor 1 Mount the sensor on a vertical exterior wall, at least 6 inches below any overhang. Choose a location protected from direct sunlight. 2 Place sensor securely in bracket, facing away from wall. M28491 To install indoor air sensor M28849A 1 Remove the wallplate and mount it 4 to 6 feet above the floor on an interior wall. Drill 3/16-inch holes for drywall, 7/32-inch for plaster. 2 Attach sensor securely to wallplate as shown. Do not install the indoor air sensor where it can be affected by:
Drafts or dead spots behind doors and in corners. Hot or cold air from ducts. Radiant heat from sun or appliances. Concealed pipes and chimneys. Unheated (uncooled) areas such as an outside wall M32936A To install Entry/Exit Remote or Vent Boost Remote Mounting the remote is optional. 1 Remove the front cover from the remote. 2 Use provided screws and wall anchors to fasten the remote to the wall. Drill 3/16-inch holes for drywall, 7/32-inch for plaster. 3 Replace the cover on the remote. M33095 11 I/O-CHTSTAT03 69-268801 System Installation Guide 6 Installer options (ISU) To setup the thermostat, press MENU and scroll down to press INSTALLER OPTIONS. Enter the date code (password) when prompted. The date code is printed on the back of the thermostat; or press MENU > EQUIPMENT STATUS to find the date code. After you enter the password, press CREATE SETUP to setup the thermostat. A brief summary of installer options follows. You can download a complete list of all options at http://customer.honeywell.com. Create Setup: Press CREATE SETUP to set all system settings one by one. View/Edit Current Setup: Press VIEW/EDIT CURRENT SETUP to select a specific function and make quick changes. ComfortNet User Menu: Press COMFORTNET USER MENU to view equipment information. Installer Test: Press INSTALLER TEST to quickly determine if the heat, cool, fan and thermostat are operating properly. Minimum off timers are ignored during the test. Data Logs: Press DATA LOGS to view the Alerts Log and User Interactions Log. Wireless Device Manager: Press WIRELESS DEVICE MANAGER to add or remove wireless accessories. Advanced Options: Press ADVANCED OPTIONS to setup the thermostat using a USB device or to restore the thermostat to the factory default settings. TIP: You can use the thermostat USB port to download all system configuration and installer options, including your company name and contact information. You can upload this data to each thermostat you install, to save time. R: Residential C: Commercial B: Both ISU Function ISU Function Language 1000 Residential/Commercial 1010 Device Name 1030 Device Name on Home Screen 1030 Programmable/Non-programmable 1040 Fahrenheit/Celsius 1050 Outdoor Air Sensor 1060 Heating System Type 2000 Heating Equipment Type 2010 Heat Stages 2070 Cool/Compressor Stages 2070 Backup Heat Stages 2070 Backup Heat Type 2180 Manual/Auto Changeover 3000 Auto Changeover Deadband 3000 Temperature Control Options 3010 Finish With High Cool Stage 3020 Finish With High Heat Stage 3021 3030 Staging Control - Cool Differentials 3050-3060 Staging Control - Heat Differentials 3090 3110 3120 3120 Staging Control - Backup Heat Differentials Backup Heat Upstage Timer Outdoor Compressor Lockout Outdoor Backup Heat Lockout 69-268801 I/O-CHTSTAT03 B B B C B B B B B B B B B B B B B B B B B B B B Cool/Compressor Cycles Per Hour Heat Cycles Per Hour Backup Heat Cycles Per Hour 3140 3150 3160 3170-3190 Cooling Derivative, Integral, Throttling range 3200-3220 Heating Derivative, Integral, Throttling range 3240 3260 3260 4000 4010 4020 4030 4050 4060 4070 4080 4090 4100 4100 4110 4120 Minimum Compressor Off Time Extended Fan Run Time in Cool Extended Fan Run Time in Heat Number of Schedule Periods Pre-occupancy Purge Duration Override: Standard or Initiate Occupancy Override Duration Minimum Recovery Settings - Heat Maximum Recovery Settings - Heat Minimum Recovery Settings - Cool Maximum Recovery Settings - Cool Adaptive Intelligent Recovery Minimum Cool Setpoint Maximum Heat Setpoint Keypad Lockout Entry/Exit Remote -
Home/Occupied Cool Setpoint Entry/Exit Remote -
Home/Occupied Heat Setpoint 4120 12 B B B C C B B B B C C C C C C C R B B B B B 6 Installer options (ISU) ISU Function 4130 4130 4140 4140 5040 7000 7020 7110 7110 7120 7120 7120 8000 8010 8050 8060 8070 8100 8100 9000 9010 9020 9070 9080 B B B Entry/Exit Remote -
Away/Unoccupied Cool Setpoint Entry/Exit Remote -
Away/Unoccupied Heat Setpoint Entry/Exit Remote -
Vacation/Holiday Cool Setpoint Entry/Exit Remote -
Vacation/Holiday Heat Setpoint B Indoor Sensors Used for Temperature Control B Filter Type B B Number of Air Filters B Air Filter Replacement Reminder B Air Filter 2 Replacement Reminder B EAC Cell Cleaning Reminder EAC Pre-Filter Cleaning Reminder B B EAC Post-Filter Replacement Reminder Humidifier Type B Indoor Sensor Used for Humidification Control B B Humidification - Window Protection B System Modes Allowing Humidification Humidification Control B Clean Tank / Water Filter Replacement Reminder B B Humidifier Pad Replacement Reminder Dehumidification Equipment B Indoor Sensor Used for Dehumidification Control B Humidity Sensor Displayed on the Home Screen B Dehumidification - Overcooling Limit R C Dehumidification Control CTK03 ComfortNet Communicating Thermostat Function ISU 9090 9100 9180 9190 9200 9200 9200 C C B B B B Dehumidification Minimum On Time High Humidity Comfort Reset Setting Dehumidification Away Mode Dehumidification Away Mode - Fan Control Dehumidification Away Mode -
Low Limit Temperature Dehumidification Away Mode -
Temperature Setting Dehumidification Away Mode -
Dehumidification Setting Dehumidifier Filter Replacement Reminder Ventilation Type Ventilation Control Method Number of Bedrooms Size of House Enter Equipment Ventilation Rate Ventilation Percent On Time Ventilator Filter Cleaning Reminder Number of UV Devices UV Bulb Replacement Reminder UV Bulb 2 Replacement Reminder Installer Custom Reminders Clock Format Daylight Saving Time Indoor Temperature Display Offset Indoor Humidity Display Offset B B 9210 B 10000 B 10050 R 10090 R 10090 R 10100 B 10120 B 10170 B 11000 B 11050 B 11050 B 12000 B 14000 B 14010 B 14020 14020 B 15000-15020 Dealer name, phone, email, website, message B ComfortNet User Menu Press MENU > INSTALLER OPTIONS > COMFORTNET USER MENU Additional equipment information is found in the ComfortNet User Menu. Press MENU and scroll down to press INSTALLER OPTIONS. Enter the date code
(password) when prompted. The date code is printed on the back of the thermostat; or press MENU > EQUIPMENT STATUS to find the date code. After you enter the password, press COMFORTNET USER MENU and then select the equipment type (furnace, air handler, air conditioner, heat pump) to view the specifications. Each equipment type is divided into categories which include:
Configuration: Provides information regarding the setup of the equipment. An example of configuration data is the number of cooling stages for an AC condensing unit. Diagnostics: Provides a fault history of the equipment and allows the installer to clear the fault history. Identification: Provides the model and serial number of the equipment and software revision information. Sensors: Provides the sensor data of the equipment. In some instances, it may allow the installer to setup or turn off a sensor. Setup: Allows the installer to change the settings of the equipment. Status: Provides the current status of the equipment. The following pages provide submenus of the above categories for each equipment type that may be used with this thermostat. 13 I/O-CHTSTAT03 69-268801 System Installation Guide Furnace User Menus Configuration (CONFIG) Sub-menu Item Indication (for Display Only; not User Modifiable) Number of Heat Stages (HT STG) Displays the number of furnace heating stages Input Rate (BTU/HR) Motor HP (1/2, 3/4 or 1 MTR HP) Displays the furnace input rate in kBtu/hr Displays the furnace indoor blower motor horse power Diagnostics (DIAG) Sub-menu Item Fault 1 (FAULT #1) Fault 2 (FAULT #2) Fault 3 (FAULT #3) Fault 4 (FAULT #4) Fault 5 (FAULT #5) Fault 6 (FAULT #6) Clear Fault History
(CLEAR) Indication/User Modifiable Options Comments For display only Most recent furnace fault Next most recent furnace fault For display only Next most recent furnace fault For display only Next most recent furnace fault For display only Next most recent furnace fault For display only For display only Least recent furnace fault NO or YES Selecting YES clears the fault history NOTE: Consecutively repeated faults are shown a maximum of 3 times. Identification (IDENT) Sub-menu Item Model Number (MOD NUM) Serial Number (SER NUM) Software (SOFTWARE) Indication (for Display Only; not User Modifiable) Displays the furnace model number Displays the furnace serial number (Optional) Displays application software revision 69-268801 I/O-CHTSTAT03 14 CTK03 ComfortNet Communicating Thermostat Setup (SETUP) Sub-menu Item Heat Airflow Trim
(HT TRM) Heat ON Delay
(HT ON) Heat OFF Delay
(HT OFF) Heating Air Flow
(HT ADJ) Status (STATUS) Sub-menu Item Mode (MODE) CFM (CFM) User Modifiable Options
-10% to +10% in 2% Increments
(Default 0%) 5, 10, 15, 20, 25, or 30 seconds
(Default 20) 30, 60, 90, 120, 150, or 180 seconds
(Default 120) 1, 2, 3, 4 (Default 2) Comments Trims the heating airflow by the selected amount. Selects the indoor blower heat on delay Selects the indoor blower heat off delay Selects the nominal heating airflow Indication (for Display Only; not User Modifiable) Displays the current furnace operating mode Displays the airflow for the current operating mode Comments Non-Comm (Non-COMM applies only to a communicating furnace matched with a non-
communicating AC) Sub-menu Item User Modifiable Options 18, 24, 30, 36, 42, 48, or Cool Airflow (CL CFM) 60 (Default 18)
-10% to +10% in 2%
Cool Airflow Trim Increments (Default 0%)
(CL TRM) Cool Airflow A, B, C, or D (Default A) Profile (CL PRFL) Cool ON Delay
(CL ON) Cool OFF Delay
(CL OFF) Selects the airflow for the non-communicating 1-stage AC unit Selects the airflow trim amount for the noncommunicating 1-stage AC unit Selects the airflow profile for the noncommunicating 1-stage AC unit Selects the indoor blower on delay for the noncommunicating 1-stage AC unit Selects the indoor blower off delay for the noncommunicating 1-stage AC unit 5, 10, 20, or 30 seconds
(Default 5) 30, 60, 90, or 120 seconds
(Default 30) 15 I/O-CHTSTAT03 69-268801 System Installation Guide Air Handler User Menus Configuration (CONFIG) Sub-menu Item Indication (for Display Only; not User Modifiable) Displays the size, in kW, of the selected electric heaters Electric Heat Size (HTR KW) Motor HP (1/2, 3/4 or 1 MTR HP) Displays the furnace indoor blower motor horse power Heat ON Delay (HT ON) Heat OFF Delay (HT OFF) Displays the electric heat indoor blower on delay Displays the electric heat indoor blower off delay Diagnostics (DIAG) Sub-menu Item Fault 1 (FAULT #1) Fault 2 (FAULT #2) Fault 3 (FAULT #3) Fault 4 (FAULT #4) Fault 5 (FAULT #5) Fault 6 (FAULT #6) Clear Fault History
(CLEAR) Indication/User Modifiable Options Comments Most recent air handler fault Next most recent air handler fault Next most recent air handler fault Next most recent air handler fault Next most recent air handler fault Least recent air handler fault NO or YES For display only For display only For display only For display only For display only For display only Selecting YES clears the fault history NOTE: Consecutively repeated faults are shown a maximum of 3 times. Identification (IDENT) Sub-menu Item Indication (for Display Only; not User Modifiable) Model Number (MOD NUM) Displays the air handler model number Serial Number (SER NUM) Displays the air handler serial number (Optional) Software (SOFTWARE) Displays application software revision Setup (SETUP) Sub-menu Item Heat Airflow Trim
(HT TRM) User Modifiable Options
-10% to +10% in 2% Increments
(Default 0%) Comments Trims the electric heating airflow by the selected amount. Status (STATUS) Sub-menu Item Indication (for Display Only; not User Modifiable) Mode (MODE) CFM (CFM) Displays the current air handler operating mode Displays the airflow for the current operating mode 69-268801 I/O-CHTSTAT03 16 CTK03 ComfortNet Communicating Thermostat Heat Pump/Air Conditioner User Menus Configuration (CONFIG) Sub-menu Item AC Tonnage (TONS) Number of AC Stages
(CL STG) Number of HP Stages
(HT STG) Diagnostics (DIAG) Sub-menu Item Fault 1 (FAULT #1) Fault 2 (FAULT #2) Fault 3 (FAULT #3) Fault 4 (FAULT #4) Fault 5 (FAULT #5) Fault 6 (FAULT #6) Clear Fault History
(CLEAR) Indication (for Display Only; not User Modifiable) Displays the air conditioning tonnage; applies to AC and HP. Displays the number of air conditioning stages; applies to AC and HP. Displays the number of heat pump stages; applies to HP only. Indication/User Modifiable Options Most recent AC/HP fault Next most recent AC/HP fault Next most recent AC/HP fault Next most recent AC/HP fault Next most recent AC/HP fault Least recent AC/HP fault NO or YES Comments For display only For display only For display only For display only For display only For display only Selecting YES clears the fault history NOTE: Consecutively repeated faults are shown a maximum of 3 times. Identification (IDENT) Sub-menu Item Indication (for Display Only; not User Modifiable) Model Number (MOD NUM) Displays the air conditioner or heat pump model number Serial Number (SER NUM) Displays the air conditioner or heat pump serial number
(Optional) Displays application software revision Software (SOFTWARE) Sensors (SENSORS) Sub-menu Item Outdoor Air Temperature
(AIR TMP) Indication/User Modifiable Options Displays the outdoor air temperature Outdoor Coil Temperature
(COIL TMP) Displays the outdoor coil temperature Comments Sensor may or may not be available on an air conditioner. Check air conditioner instructions for details. Applies for heat pump operation. 17 I/O-CHTSTAT03 69-268801 System Installation Guide Status (STATUS) Sub-menu Item Indication (for Display Only; not User Modifiable) Mode (MODE) CFM (CFM) Displays the current air handler operating mode Displays the airflow for the current operating mode Cool Set-up (SETUP) Sub-menu Cool Airflow Trim
(CL TRM) Cool Airflow Profile
(CL PRFL) Cool ON Delay (CL ON) Cool OFF Delay (CL OFF) Dehumidification Select (DEHUM) Item User Modifiable Options Comments
-10% to +10% in 2%
Increments (Default 0%) A, B, C, or D (Default D) Selects the airflow profile; applies to air Selects the airflow trim amount; applies to air conditioner only. 5, 10, 20, or 30 seconds
(Default 5) 30, 60, 90, or 120 seconds (Default 30) ON or OFF (Default is OFF) conditioner only. Selects the indoor blower on delay; applies to air conditioner only. Selects the indoor blower off delay; applies to air conditioner only. Selecting OFF disables dehumidification;
selecting ON enables dehumidification;
applies to air conditioner only. Comments Heat Set-Up (HT SETUP) Applies to Heat Pump Systems Only Sub-menu Item User Modifiable Options Heat Airflow Trim
(HT TRM) Heat ON Delay
(HT ON) Heat OFF Delay
(HT OFF) Defrost Interval
(DEFROST) Compressor Delay (CMP DLY)
-10% to +10% in 2%
Increments (Default 0%) 5, 10, or 15 seconds
(Default 5-sec.) 30, 50, 70, or 90 seconds
(Default 30-sec.) 30, 60, 90, or 120 minutes
(Default 30-min.) 0, 5, 15, or 30 seconds
(Default 30-sec.) Selects the airflow trim amount; applies to heat pump only. Selects the indoor blower on delay; applies to heat pump only. Selects the indoor blower off delay; applies to heat pump only. Selects the time interval between defrost;
applies to heat pump only. Selects the compressor off time after a reversing valve shift; applies to heat pump only. 69-268801 I/O-CHTSTAT03 18 CTK03 ComfortNet Communicating Thermostat Wiring humidifier to the IFC To change installer setup (ISU) information, see pages 12-13. Wiring TrueSTEAM to IFC THERMOSTAT IFC TRUESTEAM 1 2 R C 24 V 24 V HUM HUM C GT R RT GF EXT 1 2 R C HUM HUM 1. WIRE THERMOSTAT AND TrueSTEAM AS SHOWN. 2. SET THERMOSTAT ISU 8000 TO STEAM. 3. SET TrueSTEAM DIP SWITCHES AS SHOWN (3 DOWN, 4 UP, 5 DOWN). NOTE FAN INTERLOCK IS HANDLED BY THE COMFORTNET COMMUNICATION. TrueSTEAM DIP SWITCHES 1 2 3 4 5 6 ON OFF AFS MONITOR RECOMMENDED MCR33172 Wiring TrueEASE to IFC THERMOSTAT IFC 1 2 R C 1 2 R C HUM HUM HUM CONTROL 1. WIRE THERMOSTAT AND TrueEASE AS SHOWN. 2. SET THERMOSTAT ISU 8000 TO BYPASS OR FAN POWERED. 3. SET TrueEASE DIP SWITCHES AS SHOWN :
TOP DIP SWITCH SET TO THE RIGHT BOTTOM DIP SWITCH SET TO THE LEFT TrueEASE BYPASS FAN POWERED TrueEASE DIP SWITCHES NOTE FAN INTERLOCK IS HANDLED BY THE COMFORTNET COMMUNICATION. 19 I/O-CHTSTAT03 69-268801 MCR33173 System Installation Guide Heat pump with outdoor temperature lockouts Outdoor temperature lockouts are optional. See Installer Setup options (ISU 3120). Electric - Backup heat allowed to run with heat pump e r u t a r e p m e t r o o d t u O e r u t a r e p m e t r o o d t u O Heat pump only Heat pump with backup heat as needed *
Backup heat only Backup heat lockout Compressor lockout
* No backup heat unless indoor temperature drops to selected Backup Heat Differential setting, or Backup Heat Upstage Timer expires. Heat pump stays ON when backup heat turns on. Fossil Fuel - Backup heat NOT allowed to run with heat pump Heat pump only Heat pump or backup heat operates *
Backup heat only Backup heat lockout Compressor lockout
* No backup heat unless indoor temperature drops to selected Backup Heat Differential setting, or Backup Heat Upstage Timer expires. Heat pump turns OFF when backup heat turns on. 69-268801 I/O-CHTSTAT03 20 CTK03 ComfortNet Communicating Thermostat Basic and Advanced Temperature Control Options (ISU 3010) Basic Options: The Installer Setup displays basic temperature control options which include Backup Heat Differential, Backup Heat Upstage Timer and Outdoor Temperature Lockouts. Note: Outdoor Temperature Lockouts only apply to Heat Pump applications. Advanced Options: The Installer Setup displays both Basic and Advanced Options. Advanced temperature control options include Finish With High Cool Stage, Finish With High Heat Stage, Temperature Differential settings between all stages and Cycle Rate settings per stage. Finish With High Heat or Cool Stage - When a multi-stage heating or cooling system is used, this feature keeps the high stage of the heating or cooling equipment running until the desired setpoint is reached. Backup heat differential and upstage timer A backup heat differential and backup heat upstage timer can be set on heat pump systems with backup heat. See installer setup options (ISU 3090-3110). Normal operation When the Backup Heat Differential is set to Comfort, the thermostat uses backup heat as needed to keep the indoor temperature within 1 F (0.5 C) of the set-
point. When the Backup Heat Differential is set to 2 F or higher, backup heat is not used unless the indoor temperature drops to the Backup Heat Differential setting or the Backup Heat Upstage Timer expires, whichever occurs first. The upstage timer starts when the highest stage of the previous equipment type turns on. Manual temperature change When the Backup Heat Differential is set to Comfort, the thermostat uses backup heat as needed to keep the indoor temperature within 1 F (0.5 C) of the set-
point. When the Backup Heat Differential is set to 2 F or higher, if the heat pump is making progress as expected, backup heat will not be used to reach the new setpoint. Set to a higher number to use less backup heat (a greater difference between the current indoor temperature and the new setpoint is required to turn on backup heat). See notes below. Programmed recovery If the heat pump is making progress as expected, backup heat will not be used to reach the setpoint of the next program period. Backup heat is always restrict-
ed during a programmed recovery when the Adaptive Intelligent Recovery feature is used. See note below. During a programmed recovery (or when the temperature setpoint is changed by the user), the thermostat waits to turn on the backup heat depending on system performance, load conditions and how many degrees the temperature setpoint is changed. Backup heat will be used ONLY when the temperature is not rising quickly enough to reach the setpoint in a reasonable time. If the backup heat was used in the last 2 hours because the heat pump was not able to maintain the setpoint, the thermostat may turn on the backup heat earlier when the user raises the setpoint. 21 I/O-CHTSTAT03 69-268801 System Installation Guide Humidification The thermostat reads the indoor humidity level and allows the user to set a humidification setting with or without window protection. Window Protection Window Protection limits the amount of humidity to prevent frost or condensa-
tion on windows. Window Protection (ISU 8050) requires an outdoor sensor. The maximum humidity level that is allowed ("Window Limit") is displayed on the Humidification Settings screen. The thermostat prevents frost or condensation on windows by not allowing the humidity to go above the Window Limit when it is controlling the humidifier. This helps inform the user as to why their humidity setting might not be reached at times. The Window Limit is based on the current outdoor temperature and the user's window protection setting. If Window Protection is turned Off, the ther-
mostat controls the humidity level to the user's desired humidity setting. Frost or con-
densation may appear on windows. To see all humidification options, press MENU > INSTALLER OPTIONS > VIEW/EDIT CURRENT SETUP >
HUMIDIFICATION. Dehumidification - Residential The thermostat reads the indoor humidity level and allows the user to set a dehu-
midification setting. When set up for dehumidification using the cooling system, an overcooling limit can be set from 0 F to 3 F (ISU 9070). The thermostat uses the cooling system to reduce humidity by lowering the temperature up to 3 F below the current cool setpoint until the desired humidity level is reached. To see all dehumidification options, press MENU > INSTALLER OPTIONS > VIEW/EDIT CURRENT SETUP >
DEHUMIDIFICATION. 69-268801 I/O-CHTSTAT03 22 CTK03 ComfortNet Communicating Thermostat Dehumidification - Commercial The thermostat reads the indoor humidity level and allows the user to set a dehumidification setting. Dehumidification using the cooling system has the following methods of dehumidification control (ISU 9080):
Basic: This option uses the cooling system to reach the desired humidity level. Minimum On Time and High Humidity Comfort Reset are not used with this method. This option should only be used if the equipment can lower the fan speed in a call for dehumidification. Minimum on Time (ISU 9090): This option ensures that the compressor runs long enough to effectively reduce humidity when the cooling equipment is cycled on. The compressor will run for the minimum "on time" you set until the desired humidity level is reached. High Humidity Comfort Reset (ISU 9100): This option uses the cooling system to lower the temperature up to 5 F below the current cool setpoint until the desired humidity is reached. The high humidity comfort range is from 1 to 5 F. High Humidity Comfort Reset with Minimum On Time (ISU 9090 and ISU 9100): This method uses both options above to reduce humidity while maintaining a comfortable temperature. To see all dehumidification options, press MENU > INSTALLER OPTIONS > VIEW/EDIT CURRENT SETUP >
DEHUMIDIFICATION. 23 I/O-CHTSTAT03 69-268801 System Installation Guide Dehumidification Away Mode Dehumidification Away Mode protects the home when unoccupied for long periods of time during hot and humid weather by maintaining the desired humidity and temperature settings. To start Dehumidification Away Mode, press Menu, then press Dehumidification Away Mode. The thermostat automatically follows settings that are set by the dealer during installer setup. Press Cancel to end Dehumidification Away Mode. Southern Dehumidification Away Mode Options: (ISU 9180 to 9200) Fan: Auto, On or Circulate Low Limit Temperature Setting: The thermostat allows the cooling system to lower the indoor air to the Low Limit Temperature Setting to control humidity. Temperature Setting: The temperature maintained while Dehumidification Away Mode is active and the desired humidity level is satisfied. Dehumidification Setting: The desired humidity level while Dehumidification Away Mode is active. Ventilation Ventilation Control Method (ISU 10050) The thermostat can control the fan to meet either ASHRAE or Percent On Time settings. If the required ventilation has not been achieved for ASHRAE or Percent On Time during calls for heat and cool, the thermostat will force the fan on. ASHRAE: The thermostat operates the fan to meet the ASHRAE 62.2 ventilation standard based on CFM, number of bedrooms, and square footage of the house. ASHRAE 62.2 can only be met if the fan is running. If the fan is off for any reason (set up to turn Off during Sleep period, turned off by user etc.), ASHRAE 62.2 is not met during those times. Percent On Time: The thermostat operates the fan based on a percentage entered in the installer setup (ISU 10120). For example, if Percent On Time is set to 50%, the fan will run at random times during a 1 hour period until it reaches a 50% run time (approximately 30 minutes). Options 10% to 100%. To see all ventilation options, press MENU > INSTALLER OPTIONS > VIEW/EDIT CURRENT SETUP >
VENTILATION. 69-268801 I/O-CHTSTAT03 24 Indoor sensor operation CTK03 ComfortNet Communicating Thermostat Temperature control The thermostat can be set to respond to its internal temperature sensor, or to an option-
al remote indoor sensor. If multiple sensors are used, the thermostat will respond to an average of temperatures detected at each sensor. Humidification control If optional remote indoor sensors are installed, you can choose which sensor you want to use for humidification control. You can use a different sensor for dehumidifica-
tion. Dehumidification control If optional remote indoor sensors are installed, you can choose which sensor you want to use for dehumidification con-
trol. For example, you can use one sensor for humidification control, and another for dehumidification. Wireless indoor sensor Battery level indicators (when batteries are inserted) Good: Status light flashes green for 5 seconds. Low: Status light flashes red for 5 seconds. Use fresh batteries. Battery level indicators (during use) Good: Status light remains off. Low: Battery power will be depleted in about 2 months. Thermostat displays Low Battery warning. Status light remains off. Critical: Battery power will be depleted in about 23 weeks. Status light flashes red. The thermostat can use up to 6 optional wireless sensors. 25 I/O-CHTSTAT03 69-268801 System Installation Guide Alerts Log MENU > INSTALLER OPTIONS > DATA LOGS > ALERTS LOG The thermostat saves the most recent 25 alerts. It records the date, time, alert status (snoozed, dismissed, recovered), and diagnostic information to help you identify and correct problems. User Interactions Log MENU > INSTALLER OPTIONS > DATA LOGS > USER INTERACTIONS LOG Check this log to find out if a problem was caused by an accidental user error. The log shows most changes made to thermostat settings, by time and date, and describes what change was made. The thermostat records the most recent 250 changes. You can quickly search them by date and time, or by function. This feature can be turned off if necessary, so that no user interactions are recorded. Examples:
*
*
*
[date, time] Heat temperature set to 80 F
[date, time] System mode set to Off
[date, time] Installer setup changed heating equipment type Replacing system components Follow steps below to disconnect the thermostat and RedLINK accessories. To replace a thermostat At the Portable Comfort Control 1 Press and hold the blank space (or arrow if present) in the lower right hand corner of the screen until the display changes. 2 Press REMOVE, then YES to disconnect from the old thermostat. Press and hold in lower right corner of screen MCR32958 At the Indoor Sensor, Entry/Exit Remote, Vent Boost Remote, RedLINK Internet Gateway or TrueSTEAM Wireless Adapter 1 Press and hold the CONNECT button on the RedLINK accessory until the status light glows amber (hold for about 10 seconds). This will disconnect the device from the old thermostat. Re-connect RedLINK accessories 1 Follow the steps in Link optional accessories to wireless network on page 9. 69-268801 I/O-CHTSTAT03 26 CTK03 ComfortNet Communicating Thermostat Replacing system components To remove accessories from a thermostat At the thermostat 1 Press MENU and scroll down to press INSTALLER OPTIONS. Enter the date code
(password) when prompted. The date code is printed on the back of the thermostat; or press MENU > EQUIPMENT STATUS to find the date code. 2 After you enter the password, scroll down to select WIRELESS DEVICE MANAGER. 3 Press REMOVE DEVICE, then select the device you want to remove. Specifications & replacement parts Operating Ambient Temperature Thermostat: 32 to 120 F (0 to 48.9 C) Portable Comfort Control: 32 to 120 F (0 to 48.9 C) Wireless Outdoor Sensor: -40 to 140 F (-40 to 60 C) Wireless Indoor Sensor: 0 to 120 F (-17.8 to 48.9 C) For Optimal Battery Life: 35 to 114 F (1.7 to 45.6 C) RedLINK Internet Gateway: 32 to 120 F (0 to 48.9 C) Operating Relative Humidity Thermostat: 5% to 90% (non-condensing) Portable Comfort Control: 5% to 90% (non-condensing) Wireless Outdoor Sensor: 0% to 100% (condensing) Wireless Indoor Sensor: 5% to 90% (non-condensing) RedLINK Internet Gateway: 5% to 95% (non-condensing) Physical Dimensions (height, width, depth) Thermostat: 3-7/8 x 6-13/16 x 1-7/16 inches (99 x 173 mm x 36 mm) Wireless Outdoor Sensor: 5 x 3-1/2 x 1-11/16 inches (127 x 89 x 43 mm) Wireless Indoor Sensor: 2-7/8 x 1-7/8 x 15/16 inches (74 x 48 x 24 mm) Portable Comfort Control: 6-1/4 x 3-1/8 x 1-5/8 inches (158 x 80 x 38 mm) RedLINK Internet Gateway: 6 x 4-7/8 x 2-1/2 inches (152 x 124 x 64 mm) Electrical Ratings 18 to 30 VAC Accessories & Replacement Parts Item RedLINK Internet Gateway Entry/Exit Remote Vent Boost Remote Portable Comfort Control Wireless Outdoor Sensor Wireless Indoor Sensor Cover Plate (covers marks left by old thermostats) Battery Pack (For demo use only) Honeywell Part Number THM6000R1002 REM1000R1003 HVC20A1000 REM5000R1001 C7089R1013 C7189R1004 50028399-001 THP1000A1007 27 I/O-CHTSTAT03 69-268801 Regulatory information FCC Compliance Statement (Part 15.19) (USA only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1 2 This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. FCC Warning (Part 15.21) (USA only) Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Interference Statement (Part 15.105 (b)) (USA only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Thermostats and outdoor sensor To comply with FCC and Industry Canada RF exposure limits for general population/ uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Portable Comfort Control This portable transmitter with its antenna complies with FCC and Industry Canada RF exposure limits for general population/
uncontrolled exposure. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Section 7.1.2 of RSS-GEN Under Industry Canada regulations, this radio transmitter may only operate using an antenna of type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Section 7.1.3 of RSS-GEN Operation is subject to the following two conditions:
this device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device. 1 2 For assistance please visit www.ComfortNet1.com, or call toll-free: (888) 593-9988 Need Help?
Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 http://customer.honeywell.com U.S. Registered Trademark. 2012 Honeywell International Inc. 69-268801 M.S. 01-12 I/O-CHTSTAT03 Printed in U.S.A. Goodman Manufacturing Co., LP Suite 500 5151 San Felipe Houston, TX 77056
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2012-04-10 | 903 ~ 926.4 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2012-04-10
|
||||
1 | Applicant's complete, legal business name |
Ademco Inc
|
||||
1 | FCC Registration Number (FRN) |
0004788345
|
||||
1 | Physical Address |
1985 Douglas Drive
|
||||
1 |
Golden Valley, MN
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
h******@acbcert.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
HS9
|
||||
1 | Equipment Product Code |
THX9001R01
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
P**** W********
|
||||
1 | Title |
Sr. Compliance Engr
|
||||
1 | Telephone Number |
763-9********
|
||||
1 | Fax Number |
763-9********
|
||||
1 |
P******@Honeywell.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Honeywell International, Inc.
|
||||
1 | Name |
R******** J******
|
||||
1 | Physical Address |
1985 Douglas Drive North
|
||||
1 |
Golden Valley, 55422
|
|||||
1 |
United States
|
|||||
1 | Telephone Number |
763-9********
|
||||
1 | Fax Number |
763-9********
|
||||
1 |
r******@honeywell.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Thermostat THX9001R01 | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output Power listed is conducted. The antenna(s) used for this device must be installed to provide a separation distance of at least 20 cm from all persons, and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
LS Research, LLC
|
||||
1 | Name |
R**** U******
|
||||
1 | Telephone Number |
262-3********
|
||||
1 | Fax Number |
262 3********
|
||||
1 |
r******@lsr.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 903.00000000 | 926.40000000 | 0.0113500 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC