all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 1.66 MiB | ||||
1 | Operational Description | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Internal Photos | |||||||
1 | RF Exposure Info | |||||||
1 | Cover Letter(s) | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | User Manual | Users Manual | 1.66 MiB |
Equipment Interface Module Installation Guide Equipment Interface Module works with:
Prestige IAQ VisionPRO 8000 with RedLINK TMMOR 2 Wires for PowerRedLINK to Equipment Interface Module TM2 Wires for Power or Battery Only (no wires)RedLINK to Equipment Interface Module 1 Install thermostat C K RC R U1 U1 U2 U2 CONVENTIONAL HEAT PUMP S1 S1 W Y G W2 Y2 A S1 S1 O/B Y G AUX E Y2 L/A Prestige/VisionPRO with RedLINK: Mount the thermostat and wire to C and R terminals of the Equipment Interface Module (EIM), or to a separate 24 volt transformer (not provided). NOTE: When the VisionPRO with RedLINK thermostat is used with the EIM, the relays in the thermostat do not function. 2 Install equipment interface module Use screws & anchors as appropriate for the mounting surface. Mount the EIM near the HVAC equipment, or on the equipment itself. R C B WO
2 W 1 X U A 2 X U A 3 W Y Y2 G C N ECT D CONNECT A A
L NOTE: If you install more than one thermostat and EIM, the EIMs must be at least 2 feet apart. NOTE: If you are installing discharge and return air sensors, refer to the mounting instructions in the Alerts and Delta T Diagnostics Installation Instructions packed with the Prestige IAQ kit. If an EIM is mounted inside a metal cabinet, it is recommended to use a THM4000R1000 Wireless Adapter for extended wireless range. Mount the Wireless Adapter outside the metal cabinet and connect to the ABCD terminals at the EIM. 2 Strip 1/4 insulation, then insert wires as shown. WIRELESS ADAPTER THM4000R POWER W RELESS SETUP CONN CTED CONNECT EIM A B C D 3 Power optional RedLINK accessories 3.1 Install batteries in RedLINK accessories. Portable Comfort Control Wireless Outdoor Sensor*
Wireless Indoor Sensor*
Wireless Entry/Exit Remote*
Wireless Vent and Filter Boost Remote*
* Requires setup. See Installer Setup options in Step 4.5. 3.2 Connect gateway to internet and connect to power. 3.2a Connect RedLINK Internet Gateway to router or modem with Ethernet cable (RJ45). 3.2b Connect gateways power cord to an electrical outlet that is not controlled by a wall switch. 4 Performing initial setup Initial setup options define the type of system you are installing:
Residential or commercial Non-zoned or zoned 4.1 Follow prompts on the screen to select appropriate options. 3.2a 3.2b APPLICATION residential CONNECTED CONNECT Next 4.2 Link the thermostat to the equipment interface module. 4.2a Press and quickly release the CONNECT button on the EIM. Make sure the Connected light is flashing green. 3 NOTE: If the Connected light does NOT flash green, another system may be in the listening mode. Please exit the listening mode at the other system and then try again. Green Flashing: In Listening Mode - system is ready to add RedLINK devices. Green Steady: RedLINK devices are communicating. Red: RedLINK device(s) are NOT communicating. Check EIM and RedLINK devices. 4.2b While the Connected light is flashing green on the EIM, press NExT on the thermostat. After a short delay, the screen will show the thermostat is connected. Next 4.3 When you see the prompt Do you have RedLINK accessories to connect? Touch YEs or NO. If you select YEs, you will be prompted to Press Connect on all new accessories. Continue to Step 4.4. If you select NO, continue to Step 4.5. 4.4 Connect each RedLINK accessory. NOTE: Make sure accessories are at least 2 feet away from the EIM during the linking process. 4.4a While the Add Device screen is displayed (listening mode), press and quickly release the CONNECT button on each new RedLINK accessory. 4 4.4b After a short delay (up to 20 seconds), check the thermostat to confirm the connection of each RedLINK accessory. 4.4c Touch DONE at the thermostat after all new RedLINK accessories are connected. NOTE: The thermostat displays a countdown timer while in listening mode. If it detects no activity for 15 minutes, it exits listening mode. Done 4.5 Finish the initial setup. Finish the setup by selecting the desired options. Touch DONE after you select the last option you want to change. The thermostat now displays its Home screen and the thermostat setup is complete. 5 EIM wiring guide conventional systems Typical wiring of a conventional system with up to 3-stage heat and 2-stage cool with one transformer. EIM TO THERMOSTAT FURNACE TRANSFORMER 24 VAC 120 VAC R C W W2 W3 HEAT STAGE 1 HEAT STAGE 2 HEAT STAGE 3 G FAN Y COMPRESSOR STAGE 1 Y2 COMPRESSOR STAGE 2 JUMPERS 3 CONV A 4 1 SENSORS CONNECT OPTIONAL S1 AND S2 TERMINALS SENSORS TO 2 STATUS LEDS POWER HEAT COOL FAN U1 U2 U3 5 A B C D S4 S4 S3 S3 CONNECT OPTIONAL S3 AND S4 TERMINALS SENSORS TO 2 1 2 3 4 5 See guides on following pages for thermostat wiring and geothermal radiant heat wiring. Wire a maximum of 4 sensors using the S1-S4 terminals. S1-S4 terminals can be connected to an indoor sensor, outdoor sensor, discharge sensor, return sensor, dry contact device to display an alert or an occupancy sensor for remote setback. Remove jumper(s) if using separate transformers. See Economizer wiring section. Connect wireless adapter to ABCD for extended wireless range. NOTE: See following pages for additional thermostat wiring guidelines for heat pumps, geothermal systems and optional Economizer. 6 EIM wiring guide heat pump systems Typical wiring of a heat pump system with up to four-stage heat and two-stage cool with one transformer. EIM POWER HEAT COOL FAN U1 U2 U3 STATUS LEDS 4 A B C D S4 S4 S3 S3 CONNECT OPTIONAL S3 AND S4 TERMINALS SENSORS TO 2 SENSORS TO THERMOSTAT HEAT PUMP O/B AUX1 AUX2 O/B CHANGEOVER VALVE AUX1 AUX2 BACKUP HEAT STAGE 1 BACKUP HEAT STAGE 2 L/A 3 1 Y COMPRESSOR STAGE 1 Y2 G L/A 3 COMPRESSOR STAGE 2 FAN RELAY COMPRESSOR MONITOR OR ZONE PANEL JUMPERS AIR HANDLER TRANSFORMER 24 VAC 120 VAC R C CONNECT OPTIONAL S1 AND S2 TERMINALS SENSORS TO 2 1 2 3 4 See guides on following pages for thermostat wiring and geothermal radiant heat wiring. Wire a maximum of 2 sensors using the S1-S4 terminals. S1-S4 terminals can be connected to an indoor sensor, outdoor sensor, discharge sensor, return sensor, dry contact device to display an alert or an occupancy sensor for remote setback. L/A terminal sends continuous output when thermostat is set to EM HEAT mode, except when set up for Economizer or TOD. See Economizer wiring section. Connect wireless adapter to ABCD for extended wireless range. 7 EIM wiring guide geothermal radiant heat Typical wiring for geothermal radiant heat, geothermal forced-air, and backup heat with one transformer. EIM POWER HEAT COOL FAN U1 U2 U3 STATUS LEDS TO THERMOSTAT HEAT PUMP O/B AUX1 AUX2 L/A 3 O/B CHANGEOVER VALVE AUX1 AUX2 BACKUP HEAT STAGE 1 BACKUP HEAT STAGE 2 COMPRESSOR STAGE 1 Y COMPRESSOR STAGE 2 FAN RELAY COMPRESSOR MONITOR 3 OR ZONE PANEL Y2 G L OPTIONAL JUMPER 2 5 CONNECT OPTIONAL S3 AND S4 TERMINALS SENSORS TO 4 A B C D S4 S4 S3 S3 JUMPERS SENSORS GEOTHERMAL RADIANT 1 HEAT STAGE 1 AIR HANDLER TRANSFORMER 24 VAC 120 VAC R C CONNECT OPTIONAL S1 AND S2 TERMINALS SENSORS TO 4 1 2 3 4 U1, U2 or U3 terminals must be used for geothermal radiant heat. Thermostat allows 2 stages of radiant heatgeothermal (stage 1) and boiler (stage 2). U terminals are normally open dry contacts when set up for geothermal radiant heat. You must install a field jumper if radiant heat is powered by system transformer. Do NOT install a field jumper if radiant heat has its own transformer. L/A terminal sends continuous output when thermostat is set to EM HEAT mode except when set up for Economizer or TOD. See Economizer wiring section. Wire a maximum of 2 sensors using the S1-S4 terminals. S1-S4 terminals can be connected to an indoor sensor, outdoor sensor, discharge sensor, return sensor, dry contact device to display an alert or an occupancy sensor for remote setback. 5 Connect wireless adapter to ABCD for extended wireless range. 8 Using universal relays to control heating or cooling U3 U3 U2 U2 U1 U1 RH RC R C 1 24 VAC HEAT STAGE 3, COOL STAGE 3, COOL STAGE 4 OR GEOTHERMAL RADIANT HEAT 2 TRANSFORMER 24 VAC 120 VAC 1 2 U1/U2/U3 terminals are normally open dry contacts when set up for a stage of heating or cooling. You must install a field jumper if the stage of heating or cooling is powered by system transformer. Do NOT install a field jumper if the stage of heating has its own transformer. Dry contact alerts EQUIPMENT DAMAGE HAZARD. Do not apply power to S1S4 terminals. Do not connect a temperature sensor to the S1S4 terminals if set for a dry contact device. NOTE: The dry contact device must be rated for low voltage. If you are not using the S1S4 terminals on the EIM, you can connect them to a dry contact device to display an alert. Dry contact alerts include Full Drain Pan, Dirty Filter, Water Leak, System Shutdown, Service Needed, Fan Failure and Custom Alert. Dry contact device can be normally open (shown in diagram) or normally closed. NOTE: You can connect multiple Dry Contact devices in parallel to the S1S4 terminals. ONE DRY CONTACT DEVICE ONE DRY CONTACT DEVICE MULTIPLE DRY CONTACT DEVICES ON ONE SET OF TERMINALS EIM EIM S4 S4 S3 S3 MULTIPLE DRY CONTACT DEVICES ON ONE SET OF TERMINALS 9 Wiring humidification, dehumidification and ventilation
"U" terminals can be used for humidification, dehumidification or ventilation. Typical hookup of powered humidifier Typical hookup of non-powered humidifier U3 U3 U2 U2 U1 U1 RH RC R C 24 VAC POWERED HUMIDIFIER 24 VAC 120 VAC 24 VAC 120 VAC 24 VAC U3 U3 U2 U2 U1 U1 RH RC R C 1 NON-POWERED HUMIDFIER 24 VAC 120 VAC FIELD INSTALLED JUMPER BETWEEN R AND U1 Typical hookup of powered ventilation Typical hookup of non-powered ventilation U3 U3 U2 U2 U1 U1 RH RC R C 24 VAC POWERED VENTILATOR 24 VAC 120 VAC 24 VAC 120 VAC 24 VAC U3 U3 U2 U2 U1 U1 RH RC R C 1 NON-POWERED VENTILATOR 24 VAC 120 VAC FIELD INSTALLED JUMPER BETWEEN R AND U1 Typical hookup of powered dehumidifier
(whole house dehumidifer) Typical hookup of variable speed blower for dehumidification in low speed U3 U3 U2 U2 U1 U1 RH RC R C POWERED DEHUMIDIFIER 24 VAC 120 VAC 24 VAC 120 VAC U3 U3 U2 U2 U1 U1 RH RC R C OR 24 VAC 1 2 DEHUMIDIFICATION WITH LOW SPEED FAN FIELD INSTALLED JUMPER BETWEEN R AND U1 24 VAC 120 VAC Any combination of universal relays (U1, U2, U3) can be used. They are set in the thermostat installer setup. Wire the universal EIM relay to the low speed fan for dehumidification control at the equipment. The EIM relay can be set to be normally open or normally closed in the thermostat installer setup. 24 VAC 1 2 Normally open, dry contacts Normally closed, dry contacts 10 Economizer Module wiring guides Typical wiring of a W7220 Economizer Module for a heat pump system, using a VisionPRO with RedLINK thermostat or Equipment Interface Module. W7220 Economizer Module
(See wiring guidelines provided with the product) O/B N Rooftop Unit Y1 Y2 AUX AUX 2 G SD-O/B OCC E-GND AUX Y2I Y2O Y1I Y1O C R Transformer 24 VAC 120 VAC R C O/B L/A 1 Y Y2 G AUX AUX 2 2 Thermostat/EIM Typical wiring of a W7220 Economizer Module for a conventional system, using a VisionPRO with RedLINK thermostat or Equipment Interface Module. W7220 Economizer Module
(See wiring guidelines provided with the product) Rooftop Unit Y1 W1 Y2 N W2 G SD-O/B OCC E-GND AUX Y2I Y2O Y1I Y1O C R Transformer 120 VAC 24 VAC R C Y Y2 W W2 G A 1 Thermostat/EIM 1 2
"A" or "L/A" terminal must be configured for Economizer in the installer setup. These terminals are powered by the cooling transformer
(Rc terminal). Terminal AUX 2 is present only on the Equipment Interface Module. 11 Economizer Module wiring guides Typical wiring of a W7213/W7214 Economizer Module for a heat pump system, using a VisionPRO with RedLINK thermostat or Equipment Interface Module. O/B N W7213/W7214 Economizer Module
(See wiring guidelines provided with the product) Rooftop Unit Y1 Y2 AUX AUX 2 G O or B N 3 4 1 2 & 5 TR1 TR Transformer 120 VAC 24 VAC R C O/B L/A 1 Y Y2 G AUX AUX 2 2 Thermostat/EIM Typical wiring of a W7212 Economizer Module for a conventional heating system, using a VisionPRO with RedLINK thermostat or Equipment Interface Module. Rooftop Unit Y1 W1 Y2 N W2 G W7212 Economizer Module
(See wiring guidelines provided with the product) N 3 4 1 2 & 5 TR1 TR Transformer 120 VAC 24 VAC R C Y Y2 W W2 G A 1 Thermostat/EIM 1 2
"A" or "L/A" terminal must be configured for Economizer in the installer setup. These terminals are powered by the cooling transformer (Rc terminal). Terminal AUX 2 is present only on the Equipment Interface Module. 12 Control Portable Comfort To replace the Equipment Interface Module (EIM) When you replace an EIM, you must reset the RedLINK accessories before connecting them to the new thermostat. Follow the instructions below:
At the Portable Comfort Control:
Press and hold the blank space (or arrow) in the lower right hand corner of the screen until the display changes (hold for about 4 seconds). Press REMOVE, then YES to disconnect from the old thermostats. To reconnect the thermostat, go to Step 4. At the Indoor sensor, RedLINK Internet Gateway, Entry/Exit Remote, Vent-Filter Boost Remote or TruesTEAM Wireless Adapter:
Press and hold the CONNECT button on the accessory until the status light glows amber (hold for about 10 seconds). To reconnect the thermostat, go to Step 4. At the thermostat:
Go to Installer Options, Wireless Device Manager, Remove Device, and select This Thermostat. Follow the prompts on the screen to connect the thermostat to the new EIM. Press and hold Specifications and replacement parts Control for up to 4 Heat/2 Cool heat pump systems or up to 3 Heat/2 Cool conventional systems for residential and commercial applications. Operating Ambient Temperature Equipment Interface Module: -40 to 165 F (-40 to 74 C) Operating Relative Humidity Equipment Interface Module: 5% to 95% (non-condensing) Physical Dimensions (height, width, depth) Equipment Interface Module: 9-5/16 x 4-13/16 x 1-19/32 inches (91 x 147 x 42 mm) Electrical ratings Terminal W - OB Y (cooling) G (fan) W2 - Aux 1 (heating) Y2 (cooling) W3 - Aux 2 A-L/A (output) U1, U1 U2, U2 U3, U3 Voltage (50/60 Hz) 18 to 30 VAC and 750 mVDC 18 to 30 VAC 18 to 30 VAC 18 to 30 VAC 18 to 30 VAC 18 to 30 VAC 18 to 30 VAC 30 VAC max. 30 VAC max. 30 VAC max. 1.00A 1.00A 0.50A 0.60A 0.60A 1.00A 1.00A 0.50A 0.50A 0.50A Max. Current Rating 13 Accessories and replacement parts Accessories / Replacement Parts Equipment Interface Module RedL NK Internet Gateway Wireless Entry/Exit Remote Wireless Vent and Filter Boost Remote Portable Comfort Control Occupancy Sensor for Remote Setback Wireless Outdoor Sensor Wireless Indoor Sensor Wireless Outdoor Sensor 10k ohm NTC Wired Wall-mount Indoor Sensor 10k ohm NTC Wired Flush-mount Indoor Sensor 20k ohm NTC Wired Wall-mount Indoor Sensor 20k ohm NTC Wired Wall-mount Indoor Sensor 10k ohm NTC Supply or Return Air Sensor 10k ohm NTC Supply or Return Air Sensor 20k ohm NTC Supply or Return Air Sensor 20k ohm NTC Cover Plate (covers marks left by old thermostats) Wireless Adapter for TrueZone, TrueSteam, or extended wireless range Regulatory information Part Number THM5421R1021 THM6000R1002 REM1000R1003 HVC20A1000 REM5000R1001 WSK-24 C7089R1013 C7189R1004 C7089U1006 C7189U1005 C7772A1004, C7772A1012 TR21 TR21-A C7735A1000 C7041 C7770A1006 50028399-001 THM4000R1000 FCC Compliance statement (Part 15.19) (UsA only):
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation. FCC Warning (Part 15.21) (UsA only):
Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC Interference statement (Part 15.105 (b)) (UsA only):
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 14 Equipment interface module, thermostats and outdoor sensor:
To comply with FCC and Industry Canada RF exposure limits for general population/
uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter. Portable Comfort Control:
This portable transmitter with its antenna complies with FCC and Industry Canada RF exposure limits for general population/uncontrolled exposure. This device must not be co-located or operating in conjunction with any other antenna or transmitter. section 7.1.2 of Rss-GEN:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication. section 7.1.3 of Rss-GEN:
Operation is subject to the following two conditions:
1 This device may not cause interference, and 2 This device must accept any interference, including interference that may cause undesired operation of the device. 15 DIsCONNECT POWER BEFORE INsTALLATION. Can cause electrical shock or equipment damage. Must be installed by a trained, experienced technician. Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition. For assistance please visit http://customer.honeywell.com, or call toll-free:
1-800-468-1502 (residential installation) 1-888-245-1051 (commercial installation) Need Help?
Automation and Control systems Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 http://customer.honeywell.com U.S. Registered Trademark. 2012 Honeywell International Inc. 69-2758EFS01 M S. 11-12 Printed in U.S A. 69-2758EFS-01TM Module dinterface dquipement Guide dinstallation Le module dinterface dquipement fonctionne avec les dispositifs suivants :
Prestige IAQ VisionPRO 8000 avec RedLINK TMMOU 2 fils pour lalimentationRedLINK vers module dinterface dquipement TM2 fils pour l'alimentationou piles uniquement (sans fil)RedLINK vers module dinterface dquipement 1 Installation du thermostat C K RC R U1 U1 U2 U2 CONVENTIONNEL S1 S1 W Y G W2 Y2 A S1 S1 O/B Y G AUX E Y2 L/A THERMOPOMPE Prestige/VisionPRO avec RedLINK : Montez le thermostat et reliez-le aux bornes C et R du module dinterface dquipement (MIE) ou un transformateur de 24 V spar (non fourni). REMARQUE : Lorsque le thermostat VisionPRO avec RedLINK est utilis avec le module dinterface dquipement, les relais du thermostat ne fonctionnent pas. 2 Installation du module dinterface dquipement Utilisez des vis et des ancres selon le besoin pour la surface de montage. Montez le MIE prs de lquipement de CVCA ou sur l'quipement mme. R C B WO
2 W 1 X U A 2 X U A 3 W Y Y2 G C N ECT D CONNECT A A
L Dnudez sur 6 mm
(1/4 po) puis insrez les fils comme illustr. ADAPTATEUR SANS FIL REMARQUE : Si plus dun thermostat et MIE sont installs, les MIE doivent tre installs au moins 2 pieds lun de lautre. REMARQUE : Si des capteurs dair de retour ou de soufflage sont installs, consultez les instructions de montage dans la notice d'installation pour les alertes et le diagnostic Delta T emballe avec le ncessaire Prestige IAQ. Si un module dinterface dquipement est mont dans une armoire en mtal, il est recommand dutiliser un adaptateur sans fil THM4000R1000 pour plage sans fil tendue. Montez ladaptateur sans fil hors de larmoire en mtal et branchez-le aux bornes ABCD sur le module dinterface dquipement. A B C D MIE W RELESS SETUP THM4000R CONN CTED CONN CT P W R 2 3 Mise sous tension des accessoires RedLINK en option 3.1 Installation des piles dans les accessoires RedLINK. Rgulateur de confort portatif Capteur extrieur sans fil*
Capteur intrieur sans fil*
Dispositif distance sans fil de point dentre/sortie*
Dispositif distance de surventilation et de surfiltration sans fil*
* Requiert un rglage. Voir les options de configuration de linstallateur ltape 4.5. 3.2a 3.2 Connexion de la passerelle Internet et lalimentation. 3.2a Branchez la passerelle Internet RedLINK un routeur ou un modem muni dun cble Ethernet
(RJ45). 3.2b Branchez le cordon d'alimentation de la passerelle une prise lectrique non contrle par un interrupteur mural. 4 Rglage initial 3.2b Les options de rglage initial dfinissent le type de systme que vous installez :
Rsidentiel ou commercial Avec ou sans zonage 4.1 suivez les invites sur lcran pour slectionner les options appropries. APPLICATION residential CONNECTED CONNECT Suivant 4.2 Connectez le thermostat au module dinterface dquipement. 4.2a Appuyez et relchez rapidement le bouton CONNECT
(CONNEXION) sur le MIE. Assurez-vous que le voyant Connected (Connect) clignote en vert. 3 REMARQUE : Si le voyant Connected (Connect) NE clignote PAS en vert, un autre systme est peut-tre en mode dcoute. Veuillez quitter le mode dcoute sur lautre systme et essayer une nouvelle fois. Le voyant clignote en vert : En mode dcoute - Le systme est prt ajouter des dispositifs RedLINK. Le voyant en vert en continu : Les dispositifs RedLINK communiquent. Le voyant en rouge : Le ou les dispositifs RedLINK NE communiquent PAS. Vrifiez le MIE et les dispositifs RedLINK. 4.2b Pendant que le voyant Connected (Connect) clignote en vert sur le MIE, appuyez sur Next (Suivant) sur le thermostat. Aprs un court dlai, lcran indique que le dispositif est connect. Suivant 4.3 Lorsque vous voyez linvite Do you have RedLINK accessories to connect? (Avez-vous des accessoires RedLINK connecter?), touchez Yes (Oui) ou No (Non). Si vous slectionnez Yes (Oui), vous serez invit Press Connect
(Appuyer sur connecter) sur tous les nouveaux accessoires. Passez ltape 4.4. Si vous slectionnez No (Non), passez ltape 4.5. 4.4 Connectez chaque accessoire RedLINK. REMARQUE : Assurez-vous que les accessoires sont au moins 0,6 m (2 pi) du MIE durant le processus de connexion. 4.4a Lorsque le message Press Connect (Appuyer sur Connect) est affich (mode dcoute), appuyez et relcher rapidement le bouton CONNECT (CONNECTER) sur chaque nouvel accessoire RedLINK. 4 4.4b Aprs un bref dlai (20 secondes max.), vrifiez le thermostat pour confirmer la connexion de chaque accessoire RedLINK. 4.4c Touchez Done (Terminer) sur le thermostat aprs que tous les nouveaux accessoires RedLINK sont connects. REMARQUE : Le thermostat affiche un compteur rebours alors quil est en mode dcoute. Sil ne dtecte pas dactivit pendant 15 minutes, il quitte le mode d'coute. Termin 4.5 Terminez le rglage initial. Terminez le rglage en slectionnant les options dsires. Appuyez sur Done
(Termin) aprs avoir slectionn la dernire option modifier. Le thermostat affiche maintenant son cran daccueil et la thermostat setup is complete (configuration du thermostat est termine). 5 Guide de cblage du MIE systmes conventionnels Raccordement typique dun systme conventionnel avec jusqu' trois tages de chaleur et deux tages de refroidissement avec un seul transformateur. MIE VERS THERMOSTAT R C DE CHAUFFAGE 24 V c.a. 120 V c.a. TRANSFORMATEUR DE LAPPAREIL VOYANTS DEL DTAT POWER HEAT COOL FAN U1 U2 U3 5 A B C D S4 S4 S3 S3 BRANCHEZ LES CAPTEURS EN OPTION AUX BORNES S3 ET S4 2 CONV A 4 1 W W2 W3 1ER TAGE CHAUFFAGE 2e TAGE CHAUFFAGE 3e TAGE CHAUFFAGE G VENTILATEUR
(FAN) Y COMPRESSEUR
(TAGE 1) Y2 COMPRESSEUR
(TAGE 2) CAVALIERS 3 BRANCHEZ LES CAPTEURS EN OPTION AUX BORNES S1 ET S2 2 ou ou ou CAPTEURS 1 2 3 4 5 Voir les guides aux pages suivantes pour le cblage du thermostat et du chauffage rayonnant gothermique. Cblez un maximum de 4 capteurs avec les bornes S1-S4. Les bornes S1-S4 peuvent tre connectes un capteur d'intrieur, un capteur dextrieur, un capteur dvacuation, un capteur de retour, un dispositif contact sec pour afficher une alerte ou un capteur de prsence pour le dcalage distance. Retirer le ou les cavaliers si des transformateurs spars sont utiliss. Voir la section Cblage de lconomiseur. Branchez l'adaptateur sans fil aux bornes ABCD pour accrotre la porte du signal. REMARQUE : Voir les pages suivantes pour les instructions de cblage supplmentaires du thermostat pour les thermopompes, les systmes gothermiques et l'conomiseur en option. 6 Guide de cblage du MIE systmes thermopompe Raccordement typique dun systme thermopompe avec jusqu' quatre tages de chaleur et deux tages de refroidissement avec un seul transformateur. MIE POWER HEAT COOL FAN U1 U2 U3 VOYANTS DEL DTAT 4 A B C D S4 S4 S3 S3 BRANCHEZ LES CAPTEURS EN OPTION AUX BORNES S3 ET S4 2 VERS THERMOSTAT THERMOPOMPE AUX1 AUX2 O/B AUX1 AUX2 L/A 3 1 ou ou ou O/B VANNE DE COMMUTATION 1ER TAGE CHAUFFAGE DE SECOURS 2E TAGE CHAUFFAGE DE SECOURS COMPRESSEUR
(TAGE 1) COMPRESSEUR
(TAGE 2) RELAIS VENTILATEUR MONITEUR DE COMPRESSEUR OU TABLEAU DE ZONAGE Y Y2 G L/A 3 CAVALIERS TRANSFORMATEUR DU SYSTME DE TRAITEMENT DE LAIR R C 120 V c.a. 24 V c.a. CAPTEURS BRANCHEZ LES CAPTEURS EN OPTION AUX BORNES S1 ET S2 2 1 2 3 4 Consultez les guides aux pages suivantes pour le cblage du thermostat et du chauffage rayonnant gothermique. Cblez un maximum de 2 capteurs avec les bornes S1-S4. Les bornes S1-S4 peuvent tre connectes un capteur d'intrieur, un capteur dextrieur, un capteur dvacuation, un capteur de retour, un dispositif contact sec pour afficher une alerte ou un capteur de prsence pour le dcalage distance. La borne L/A envoie un signal de sortie continu lorsque le thermostat est rgl sur le mode de chauffage durgence, sauf lorsquil est configur pour un conomiseur ou TOD. Voir la section Cblage de lconomiseur. Branchez l'adaptateur sans fil aux bornes ABCD pour accrotre la porte du signal. 7 Guide de cblage du MIE chauffage rayonnant gothermique Cblage typique pour chauffage rayonnant gothermique, air puls gothermique et chauffage de secours avec un transformateur. MIE POWER HEAT COOL FAN U1 U2 U3 A B C D S4 S4 S3 S3 VOYANTS DEL DTAT CAVALIER EN OPTION 2 5 BRANCHEZ LES CAPTEURS EN OPTION AUX BORNES S3 ET S4 4 VERS THERMOSTAT THERMOPOMPE O/B AUX1 AUX2 L/A 3 ou ou ou O/B AUX1 AUX2 VANNE DE COMMUTATION 1ER TAGE CHAUFFAGE DE SECOURS 2E TAGE CHAUFFAGE DE SECOURS COMPRESSEUR
(TAGE 1) Y COMPRESSEUR
(TAGE 2) RELAIS VENTILATEUR MONITEUR DE COMPRESSEUR OU TABLEAU DE ZONAGE 3 Y2 G L TAGE 1 DE CHAUFFAGE RAYONNANT GOTHERMIQUE 1 TRANSFORMATEUR DU SYSTME DE TRAITEMENT DE LAIR R C 24 V c.a. 120 V c.a. CAVALIERS CAPTEURS BRANCHEZ LES CAPTEURS EN OPTION AUX BORNES S1 ET S2 4 1 2 3 4 5 Les bornes U1, U2 ou U3 doivent tre utilises pour le chauffage rayonnant gothermique. Le thermostat permet 2 tages de chauffage rayonnant gothermique (tage 1) et chaudire (tage 2). Les bornes U sont des contacts secs normalement ouverts lorsque le systme est configur pour un chauffage rayonnant gothermique. Un cavalier doit tre install si le chauffage rayonnant est aliment par le transformateur du systme. Ninstallez PAS un cavalier si le chauffage rayonnant a son propre transformateur. La borne L/A envoie un signal de sortie continu lorsque le thermostat est rgl sur le mode de chauffage durgence, sauf lorsquil est configur pour un conomiseur ou TOD. Voir la section Cblage de lconomiseur. Cblez un maximum de 2 capteurs avec les bornes S1-S4. Les bornes S1-S4 peuvent tre connectes un capteur d'intrieur, un capteur dextrieur, un capteur dvacuation, un capteur de retour, un dispositif contact sec pour afficher une alerte ou un capteur de prsence pour le dcalage distance. Branchez l'adaptateur sans fil aux bornes ABCD pour accrotre la porte du signal. 8 Utilisation des relais universels pour contrler le chauffage et le refroidissement CHAUFFAGE TAGE 3, REFROIDISSEMENT TAGE 3, REFROID-
ISSEMENT TAGE 4 OU CHAUFFAGE RAYONNANT GOTHERMIQUE 2 U3 U3 U2 U2 U1 U1 RH RC R C 1 24 V c.a. TRANSFORMATEUR 24 V c.a. 120 V c.a. 1 2 Les bornes U1/U2/U3 sont des contacts secs normalement ouverts lorsque le systme est configur pour un tage de chauffage ou de refroidissement. Un cavalier doit tre install si ltage de chauffage ou de refroidissement est aliment par le transformateur du systme. Ninstallez PAS de cavalier si ltage de chauffage a son propre transformateur. Alertes contact sec RIsQUE DE DOMMAGEs DE LQUIPEMENT. Ne mettez pas les bornes S1-S4 sous tension. Ne connectez pas de capteur de temprature aux bornes S1-S4 si rgl pour un dispositif contact sec. REMARQUE : Le dispositif contact sec doit tre homologu pour basse tension. Si les bornes S1-S4 ne sont pas utilises sur le module dinterface dquipement, il est possible de les connecter un dispositif contact sec pour afficher une alerte. Les alertes contact sec incluent bac de vidange plein, filtre sale, fuite deau, arrt du systme, entretien requis, panne de ventilateur et alerte personnalise. Les dispositifs contact sec peuvent tre normalement ouvert (voir le schma) ou normalement ferm. REMARQUE : Il est possible de connecter plusieurs dispositifs contact sec en parallle sur les bornes S1-S4. UN DISPOSITIF CONTACT SEC UN DISPOSITIF CONTACT SEC PLUSIEURS DISPOSITIFS CONTACT SEC SUR UN ENSEMBLE DE BORNES MIE MIE S4 S4 S3 S3 PLUSIEURS DISPOSITIFS CONTACT SEC SUR UN ENSEMBLE DE BORNES 9 Cblage pour lhumidification, la dshumidification et la ventilation Les bornes U sont utilises pour lhumidification, la dshumidification ou la ventilation. Raccordement typique dun humidificateur lectrique Raccordement typique dun humidificateur non lectrique U3 U3 U2 U2 U1 U1 RH RC R C 24 V c.a. HUMIDIFICATEUR LECTRIQUE 24 V c.a. 120 V c.a. 24 V c.a. 120 V c.a. 24 V c a U3 U3 U2 U2 U1 U1 RH RC R C 1 HUMIDIFICATEUR NON LECTRIQUE 24 V c a 120 V c a CAVALIER INSTALL SUR SITE ENTRE R ET U1 Raccordement typique dun ventilateur lectrique Raccordement typique dun ventilateur non lectrique U3 U3 U2 U2 U1 U1 RH RC R C 24 V c a VENTILATEUR LECTRIQUE 24 V c.a. 120 V c.a. 24 V c a 120 V c.a. 24 V c a U3 U3 U2 U2 U1 U1 RH RC R C 1 VENTILATEUR NON LECTRIQUE 24 V c a 120 V c a CAVALIER INSTALL SUR SITE ENTRE R ET U1 Raccordement typique dun humidifica-
teur lectrique (dshumidificateur pour toute la maison) Raccordement typique dune soufflante vitesse variable pour une dshumidifi-
cation faible vitesse U3 U3 U2 U2 U1 U1 RH RC R C DSHUMIDIFICATEUR LECTRIQUE 24 V c.a. 120 V c.a. 24 V c.a. 120 V c.a. U3 U3 U2 U2 U1 U1 RH RC R C 1 2 DSHUMIDIFICATION AVEC VENTILATEUR BASSE VITESSE CAVALIER INSTALL SUR SITE ENTRE R ET U1 24 V c a 120 V c a OU 24 V c a Toute combinaison des relais universels (U1, U2, U3) peut tre utilise. Ils sont dfinis dans la configuration de linstallateur du thermostat. Cblez le relais du MIE universel sur la vitesse de ventilateur basse pour la com-
mande de dshumidification sur lquipement. Le relais du MIE peut tre rgl sur normalement ouvert ou normalement ferm dans la configuration de linstallateur du thermostat. 24 V c.a. 1 2 Contacts secs normalement ouverts Contacts secs normalement ferms 10 Guides de cblage du module de lconomiseur Cblage typique dun module conomiseur W7220 pour un systme thermopompe, avec thermostat VisionPRO avec RedLINK ou un module dinterface dquipement. Module conomiseur W7220
(Voir les instructions de cblage fournies avec le produit) O/B N Unit de toit Y1 Y2 AUX AUX 2 G SD-O/B OCC E-GND AUX Y2I Y2O Y1I Y1O C R Transformateur 24 V c.a. 120 V c.a. R C O/B L/A 1 Y Y2 G AUX AUX 2 2 Thermostat/MIE Cblage typique dun module conomiseur W7220 pour un systme conventionnel, avec thermostat VisionPRO avec RedLINK ou un module dinterface dquipement. Module conomiseur W7220
(Voir les instructions de cblage fournies avec le produit) Unit de toit Y1 W1 Y2 N W2 G SD-O/B OCC E-GND AUX Y2I Y2O Y1I Y1O C R Transformateur 24 V c.a. 120 V c.a. R C Y Y2 W W2 G A 1 Thermostat/MIE 1 2 La borne A ou L/A doit tre configure pour l'conomiseur dans la con-
figuration de l'installateur. Ces bornes sont alimentes par le transformateur de refroidissement (borne Rc). La borne AUX 2 est uniquement prsente sur le module dinterface dquipement. 11 Guides de cblage du module de lconomiseur Cblage typique dun module conomiseur W7213/W7214 pour un systme thermopompe, avec thermostat VisionPRO avec RedLINK ou un module dinterface dquipement. O/B N Module dconomiseur W7213/W7214
(Voir les instructions de cblage fournies avec le produit) Unit de toit Y1 Y2 AUX AUX 2 G O or B N 3 4 1 2 & 5 TR1 TR Transformateur 24 V c.a. 120 V c.a. R C O/B L/A 1 Y Y2 G AUX AUX 2 2 Thermostat/MIE Cblage typique dun module conomiseur W7212 pour un systme de chauffage conventionnel, avec thermostat VisionPRO avec RedLINK ou un module dinterface dquipement. Unit de toit Y1 W1 Y2 N W2 G Module conomiseur W7212
(Voir les instructions de cblage fournies avec le produit) N 3 4 1 2 & 5 TR1 TR Transformateur 24 V c.a. 120 V c.a. R C Y Y2 W W2 G A 1 Thermostat/MIE 1 2 La borne A ou L/A doit tre configure pour l'conomiseur dans la con-
figuration de l'installateur. Ces bornes sont alimentes par le transformateur de refroidissement (borne Rc). La borne AUX 2 est uniquement prsente sur le module dinterface dquipement. 12 Rgulateur de confort portatif Pour remplacer le module dinterface dquipement (MIE) Lorsque vous remplacez un MIE, vous devez rinitialiser les accessoires RedLINK avant de les connecter au nouveau thermostat. Suivez les instructions ci-dessous :
sur le rgulateur de confort portatif :
Appuyez sur lespace vierge (ou la flche) dans le coin infrieur droit de l'cran jusqu' ce que l'affichage change
(environ 4 secondes). Appuyer sur REMOVE (RETIRER) puis sur YES (OUI) pour dbrancher de lancien thermostat. Pour reconnecter le thermostat, passez ltape 4. sur le capteur intrieur, la passerelle Internet RedLINK, le dispositif distance de point dentre/sortie, la commande distance de surventilation-surfiltration ou ladaptateur sans fil TrueSTEAM :
Appuyez sur le bouton CONNECT (CONNEXION) de laccessoire jusqu' ce que le voyant de statut orange sallume (environ 10 secondes). Pour reconnecter le thermostat, passez ltape 4. sur le thermostat :
Allez dans Installer Options, Wireless Device Manager, Remove Device, et select This Thermostat (Options de linstallateur, Gestionnaire de dispositifs sans fil, Retrait du dispositif et Slectionner ce thermostat). Suivez les invites l'cran pour connecter le thermostat au nouveau MIE. Appuyez sans relcher Caractristiques techniques et pices de rechange Rgulateurs pour systmes pompe jusqu 4 tages de chaleur/2 tages de refroidissement ou systmes conventionnels jusqu 3 tages de chaleur/2 tages de refroidissement pour applications rsidentielles et commerciales. Temprature ambiante de service Module dinterface dquipement : -40 74 C (-40 165 F) Humidit relative de service Module dinterface dquipement : 5 % 95 % (sans condensation) Dimensions physiques (hauteur, largeur, profondeur) Module dinterface dquipement : 91 x 147 x 42 mm (9 5/16 x 4 13/16 x 1 19/32 po) Caractristiques lectriques Borne W - OB Y (refroidissement) G (ventilateur) W2 - Aux 1 (chauffage) Y2 (refroidissement) W3 - Aux 2 A-L/A (sortie) U1, U1 U2, U2 U3, U3 Tension (50/60 Hz) 18 30 V c.a. et 750 mV c c. 18 30 V c.a. 18 30 V c.a. 18 30 V c.a. 18 30 V c.a. 18 30 V c.a. 18 30 V c.a. 30 V c.a. max. 30 V c.a. max. 30 V c.a. max. 1,00 A 1,00 A 0,50 A 0,60 A 0,60 A 1,00 A 1,00 A 0,50 A 0,50 A 0,50 A Courant nominal max. 13 Accessoires et pices de rechange Accessoires / Pices de rechange Module dinterface dquipement Passerelle Internet RedLINK Dispositif distance sans fil de point dentre/sortie Dispositif distance de surventilation et de surfiltration sans fil Rgulateur de confort portatif Capteur de prsence pour dcalage distance Capteur d'extrieur sans fil Capteur d'intrieur sans fil Capteur extrieur sans fil 10 k ohms coefficient de temprature ngatif Capteur intrieur montage mural fil de 10 k ohms coefficient de temprature ngatif Capteur intrieur montage encastr fil de 20 k ohms coefficient de temprature ngatif Capteur intrieur montage mural fil de 20 k ohms coefficient de temprature ngatif Capteur intrieur montage mural fil de 10 k ohms coefficient de temprature ngatif Capteur dair de retour ou dalimentation de 10 k ohms coefficient de temprature ngatif Capteur dair de retour ou dalimentation de 20 k ohms coefficient de temprature ngatif Capteur dair de retour ou dalimentation de 20 k ohms coefficient de temprature ngatif Plaque de couvercle (Sert dissimuler les marques laisses par danciens thermostats) Adaptateur sans fil pour TrueZone, TrueSteam, ou plage sans fil tendue Rfrence de pice THM5421R1021 THM6000R1002 REM1000R1003 HVC20A1000 REM5000R1001 WSK-24 C7089R1013 C7189R1004 C7089U1006 C7189U1005 C7772A1004, C7772A1012 TR21 TR21-A C7735A1000 C7041 C7770A1006 50028399-001 THM4000R1000 Informations rglementaires Dclaration de conformit la FCC (Partie 15.19) (tats-Unis uniquement) :
Cet appareil est conforme la partie 15 du rglement de la FCC. Son fonctionnement est soumis aux deux conditions suivantes :
1 Ce dispositif ne doit pas causer dinterfrences nuisibles, et 2 Ce dispositif doit accepter toutes les interfrences reues, y compris celles pouvant causer un fonctionnement non souhait. Avertissement de la FCC (Partie 15.21) (tats-Unis uniquement) :
Toute modification qui n'est pas autorise expressment par la partie responsable de la conformit de l'appareil peut rendre l'utilisateur inapte faire fonctionner l'quipement. Dclaration relative aux interfrences de la FCC (Partie 15.105 (b))
(tats-Unis uniquement) :
Cet quipement a t test et est conforme aux limites des dispositifs numriques de Classe B, conformment la Partie 15 du rglement de la FCC. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nuisibles dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de lnergie de radiofrquence, et s'il n'est pas install et utilis conformment aux instructions, peut causer des interfrences nuisibles aux communications radio. Il n'y a toutefois aucune garantie qu'une interfrence ne se produira pas dans une installation particulire. Si cet quipement cause des interfrences nuisibles la rception radio et tlvision, ce qui peut tre dtermin en teignant le dispositif et en le remettant en marche, il est recommand l'utilisateur de tenter de corriger l'interfrence par l'une des mesures suivantes :
Rorienter ou dplacer lantenne rceptrice. Augmenter la sparation entre lquipement et le rcepteur. Branchez l'quipement dans la prise d'un circuit diffrent de celui auquel le rcepteur est connect. Consulter le distributeur ou un technicien radio/TV comptent pour obtenir de laide. 14 Module dinterface dquipement, thermostats et capteur extrieur :
Pour tre conformes aux limites d'exposition aux radiofrquences tablies par FCC et Industrie Canada pour le grand public/l'exposition non contrle, la ou les antennes utilises pour ces transmetteurs doivent tre installes au moins 20 cm de toutes les personnes et ne peuvent tre situes au mme endroit qu'une autre antenne ou fonctionner conjointement avec une autre antenne ou un autre transmetteur. Rgulateur de confort portatif :
Ce transmetteur portable et son antenne sont conformes aux limites dexposition RF de la FCC et d'Industrie Canada pour la population gnrale/lexposition non con-
trle. Cet appareil ne doit pas tre situ ou fonctionner avec une autre antenne ou un autre transmetteur. section 7.1.2 de Rss-GEN :
Conformment aux normes d'Industrie Canada, ce transmetteur radio ne peut fonc-
tionner qu'avec une antenne dont le type et le gain maximum sont approuvs par Industrie Canada. Pour rduire les risques d'interfrences radio encourus par d'autres utilisateurs, le type et le gain de l'antenne doivent tre choisis de faon ce que la puissance rayonne isotrope quivalente (p.i.r.e.) ne soit pas suprieure celle ncessaire l'tablissement d'une bonne communication. section 7.1.3 de Rss-GEN :
Son fonctionnement est soumis aux deux conditions suivantes :
1 Ce dispositif ne doit pas causer d'interfrences, et 2 Ce dispositif doit accepter toutes les interfrences, y compris celles pouvant causer un fonctionnement non souhait. 15 COUPEZ L'ALIMENTATION LECTRIQUE AVANT DE COMMENCER L'INsTALLATION. Peut provoquer des chocs lectriques ou endommager le matriel. Linstallation doit tre faite par un technicien dexprience ayant reu la formation approprie. Lisez attentivement ces instructions. Le fait de ne pas les suivre risque dendommager le produit ou de constituer un danger. Besoin d'aide?
Pour obtenir de laide, merci de visiter http://customer.honeywell.com, ou dappeler le numro gratuit :
1-800-468-1502 (installation rsidentielle) 1-888-245-1051 (installation commerciale) systmes dautomatisation et de rgulation Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 http://customer.honeywell.com Marque de commerce dpose amricaine. 2012 Honeywell International Inc. 69-2758EFS01 M.S. 11-12 Imprim aux tats-Unis 69-2758EFS-01TM
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2013-01-30 | 903.01 ~ 926.4 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2013-01-30
|
||||
1 | Applicant's complete, legal business name |
Ademco Inc
|
||||
1 | FCC Registration Number (FRN) |
0004788345
|
||||
1 | Physical Address |
1985 Douglas Drive
|
||||
1 |
Golden Valley, Minnesota 55422-3922
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
d******@nwemc.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
HS9
|
||||
1 | Equipment Product Code |
THM5421R02
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
P**** W********
|
||||
1 | Title |
Sr. Compliance Engr
|
||||
1 | Telephone Number |
763-9********
|
||||
1 | Fax Number |
763-9********
|
||||
1 |
P******@Honeywell.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | THM5421R02 | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power is listed as conducted. The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter within a host device, except in accordance with FCC multi-transmitter product procedures. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Northwest EMC, Inc.
|
||||
1 | Name |
G****** K********
|
||||
1 | Telephone Number |
503-8********
|
||||
1 | Fax Number |
503-8********
|
||||
1 |
g******@nwemc.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 903.01000000 | 926.40000000 | 0.0130000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC