Plug-In Wireless Chime & Push with Flashing Light Please retain these instructions for future reference. Pack Contents
* Bell Push
* 100 ft. door chime
* 2 screws, wall anchors, adhesive pad
* 23A 12V Alkaline battery for the push BoP ate ied
* Small flat blade screwdriver Small cross head screwdriver Safety Always follow the manufacturer's advice when using power tools and wear suitable protective equipment (e.g. safety gog-
gles) when drilling holes. T-1 O oM Mat- elma 1. Open the bell push unit. Carefully insert a small flathead screw- A driver into slot A and twist gently. Lift away the front of the bell push to reveal NN the inside. 2. Set the bell push channel. It is possible that your chime may be set off by a nearby wireless device. This could be a neighbor's bell push, for example. To prevent this interfer-
ence, you may need to change to another channel. Using a flat blade screwdriver, set rotary switch B to another position, 1 to 16. Make a note of the channel setting. Your chime will need to have its switch set to the same position see Set Up The Chime. Select a tune. Switch C, in the bell push, selects the ChiMe jemsmmmmnsmmesmsenmem tune:
1=Westminster 2=Ding Dong (manufacturer's setting) 3=Ding o Mounting The Bell Push Mount the bell push using the adhesive pad or by using the two screws, as follows:
1. Hold the bell push up against the door frame or wall where you want to mount it. (Ensure the push button is at the top). 2. Make a mark on the wall where the two screw holes TJ will be. 3. Take away the bell push base and drill two holes, large enough to accommodate the oO wall plugs if necessary. oq 4. Screw the bell push to the wall through = 2 the mounting points D. 5. Insert the 12V 23A battery (included). 6. Refit the cover, locating the top catch first. a 1-3 mo Bare ent y 1. Set the chime channel. Set rotary switch E on the chime to position 1 to 16, as with the bell push. The channel set on the chime must match the channel already set on the bell push in Set Up The Bell Push. Test Your Door Chime Test your wirefree door chime at the desired location in a receptacle. 1. Press the bell push. 2. The chime should sound. Check the Troubleshooting section if the chime does not sound. Troubleshooting Chime doesnt sound when the bell push is pushed
* Check that the push battery has enough charge and is installed the right way. Note the + and - symbols molded into the back of the battery compartment. Check that the bell push channel switch and the chime channel switch are in the same position. See Set Up. Check that the distance between the bell push or the chime is not too great* (see front of pack). _ Chime sounds without being pushed
* Check that there is not water in the bell push or the chime. This can damage the electronics.
* Check that a neighbor is not using the same channel for their chime or a similar wireless system. See Set Up.
*The stated transmission range if this product is measured in open field conditions. Walls, ceilings and metal structures (i.e. reinforced uPVC) will reduce the maximum range. Disposal and Recycling Batteries and waste electrical products should not be disposed of with household waste. Please recycle where these facilities exist. Check with your local authority or retailer for recycling advice. centre Honeywell guarantees this product for 1 year from the date of purchase. Proof of purchase is required; this does not affect your statutory rights. If you require further information about your product, call the Honeywell helpline at 1-800-468-1502. Declaration Honeywell hereby declares that this product complies with Part 15 of the FCC rules and Industrial Canada standards. This device operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for regulatory compliance could void the users authority to operate the equipment. Design reg. UK3015090,3015344;
EU 180823,176672;
China ZL200430006524.9, ZL200430050301.2 c us Federal FC Communications LISTED Commission http://yourhome.honeywell.com Operating frequency: 345 MHz; 1-800-468-1502 FCC and IC certified 1-Year Limited Warranty Frquence de service : 345 MHz Baroee hae oe et Certifi FCC et IC 1 afio de garantia limitada 2007 Honeywell International Inc. All Rights Reserved. Golden Valley, MN 55422 U.S.A. Engineered by Honeywell O"N85267'33434IN 4 Proof of Purchase/Preuve d'achat/
Comprobante de compra Made in China Tous droits rserves. Model/Modle/Modelo RCWL105A1003 69-2116EFS Congu par Honeywell Fabriqu en Chine Instructions for wireless plug-in door chime (Product #51373SL) 1. Open the cover of the pushbutton with a flat screwdriver. A gentle twisting will remove the cover of the pushbutton. 2. Insert the supplied 1 X A23 batteries in the pushbutton, observe polarity, negative end is resting on the spring. ty Tnannta nn wmnd nwrnnitinan fawn thr mrurrlhlhiattrn mnawt tr thn Annw TVR wrt ewmnwant ne mw wnt tr nn omnrtanl ae SAIL A EVIE MPUOAETUEL DAE I UALR A UN RN TIN A RAL LY GEIL surface. Drill two 4.76mm holes and insert the wall plugs. Place the back plate in the right position and tighten the plate on wall with the screws supplied. 4. Position the pushbutton over the back plate so that the lip on the back plate engages into the slot. Make sure the rubber gasket is properly seated. Firmly press the pushbutton until it snaps over the back plate. 5. Plug the chime receiver into a 110/120V AC mains socket. Press the button on the pushbutton within TINY Low kk ewe we ee th we wd ee ce es nba eet ne A nen A TMT eesill flank LUY IRE Tdlisek ailt ULL Piller ids UU) SAM With OUULIU ALI Lan s Wink itdoil. 6. There are 16 different house codes provided. They are factory preset to position 1. If experience of interference in your area, you can change the house code on both the receiver and pushbutton.