Instruction Manual RPWL200A Wireless Portable Bell Push hank you for choosing this product. Please use the ollowing instructions to ensure correct installation and ise. Keep these instructions in a safe place for future eference. Leg-(oL.c-le (meres) Ut) Bell push CR2032 battery 2 Mounting screws 2 Wall anchors Adhesive pad You will need:
+ Small flat bladed screwdriver
+ Phillips head screwdriver
+ 1/4 drill bit PrN) Always follow the manufacturer's advice when using power tools and wear suitable protective equipment
(i.e. safety goggles) when drilling holes. Before drilling holes in walls, check for hidden elec-
trical cables and water pipes. The use of a cable/pipe locator may be advisable if in doubt. Installation Guide
|. Open bell push & insert battery.
\ z~\
\ 7
\(crzos2
2. To change tunes or to program new push:
Press and release chime programming button;
LED will illuminate. Press push button to hear the tune. Press push button again to hear another tune. Refer to chime instruction manual for detail. A 3. To save the tune selected:
4. Install bell push back cov wall, using hardware provided. Close the cover. ra si QZ oe Note: Before final installation position between push and cl cf Al Nr Sith Troubleshooting Two beep sounds are heard and LED flashing twice after the normal chime sound... This indicates a low battery in the chime. Install new batteries, type LR14 C size alkaline batteries. Three beep sounds are heard and LED flashing three times after the normal chime sound... This indicates a low battery in the bell push that activated the chime. Install a new battery, type CR2032. da er to -
QO YX if
, adjust distance and hime to optimize the chime within your environment. Dense walls and metal can reduce range. Specification Operating Temperature Bell Push 14F to 104F 10C to +40C RF Frequency ~ US 345 MHz |
|RF Power <1imW Battery Type CR2032 Battery Life (5 operations/day) | 18 months
|Rainproof
| Passes UL1598 rain test |
When the bell push is operated, the red feedback light does not turn on, or is only on for a short time... In normal operation, the red light will turn on for 1 second. When the battery is weak, the light will only turn on for a short time. Install a new battery, type CR2032. Chime does not work...
* Check that the batteries are the correct type. Only use alkaline batteries for chime.
+ Check that the batteries are fitted correctly (polarity correct).
+ Check that the batteries are not loose.
+ The chime could be out of range of the bell push. Try the chime in a different location.
+ The chime might not have learned the identity of the bell push. Follow the programming procedure in step 2. Note: Do not press program button for more than 15 sec-
onds; this will delete all the memory! Repeat programming procedure in step 2 to restore operation. Chime does not play tune selected... Chime might not have learned the tune selected. Follow programming sequence in step 2. Chime does not sound...
* Check the chime switch position.
* Check that the volume control is not at the minimum setting. Range is reduced...
+ Metal structures, including uPVC door frames, can re-
duce the range of the product. Avoid mounting the tele-
phone ringer or chime on or near metal structures.
+ Other equipment can cause radio interference that affects your chime.
+ Walls and ceilings will reduce the range. Weak batteries will reduce range. Replace every 12-18 months. In cold conditions (below 41F (5C)) batteries may need to be replaced more often. Disposal & Recycling Batteries and waste electrical products should not be dis-
posed of with household waste. Please recycle where these facilities exist. Check with your local authority or retailer for recycling advice. Guarantee Honeywell guarantees this product for 1 year from the date of purchase. Proof of purchase is required; this does not affect your statutory rights. If you require further information about your product, call the Honeywell helpline at 1-800-468-1502. 1BI-To Ue lile)a) Honeywell hereby declares that this product complies with Part 15 of the FCC rules and Industrial Canada standards. This device operation is subject to the following two condi-
tions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved |
by the party responsible for regulatory compliance could |
void the users authority to operate the equipment. |