FCC ID: M82-MITW102 Tablet Computer

Mobile Computer MIT-W102XXXXXXXXXXXXXXXX User Manual MIT-W102 1 Ver 1.1 Copyright The documentation and the software included with this product are copyrighted 2020 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use. Acknowledgements All other product names or trademarks are properties of their respective owners. Intended use The MIT-W102 is intended for integration with hospital system. It is designed for general purpose for hospital environment. For data collection and display for reference. It shall not be used for life-supporting system. Intended user group The primary users for the MIT-W102 series are professional healthcare personnel and general patient groups. It is appropriate for users aged between 18 and 55 to use the tablet and users weight and health are not relevant. 2 Declaration of Conformity CE Conformity Statement Radio products with the CE alert marking comply with the RED Directive

(2014/53/EU) issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European Norms (in brackets are the equivalent international standards). EN 62368-1 (IEC62368-1) - Product Safety EN 300 328 Technical requirement for radio equipment EN 301 893 Technical requirement for radio equipment ET S301 489 General EMC requirements for radio equipment Products that contain the radio transmitter are labeled with CE alert marking and may also carry the CE logo. FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference;

2. This device must accept any interference received, including interference that may cause undesired operation. The WLAN & BT function of this product uses a certified module and according to FCC regulations contains RF module FCC ID : PPD-QCNFA364AH , IC :

4104A-QCNFA364A or FCC ID : TX2-RTL8822CE , IC : 6317A-RTL8822CE. CAUTION!

Exposure to Radio Frequency Radiation. The radiated output of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized. When connecting an external antenna to the device, the antenna shall be placed in such a manner to minimize the potential for human contact during normal operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For body worn operation, this device has been tested and meets FCC RF exposure guidelines. When 3 used with an accessory that contains metal may not ensure compliance with FCC RF exposure guidelines. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced computer technician for help Warning! Any changes or modifications made to the equipment which are not expressly approved by the relevant standards authority could void your authority to operate the equipment. Caution! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Technical Support and Assistance 1. Visit the Advantech website at http://support.advantech.com where you can find MIT-W102 User Manual I the latest information about the product. 2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call:

4 Product name and serial number Description of your peripheral attachments Description of your software (operating system, version, application software, etc.) A complete description of the problem The exact wording of any error messages Details of preparatory treatment or disposal Installation is only to be carried out by manufacturer authorized and trained personnel. Regarding calibrating the device, we suggest to send back the tablet to the supplier for annually check. Safety Instructions 1. Read these safety instructions carefully. 2. Keep this user manual for later reference. 3. Disconnect this equipment from AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall could cause damage. 7. The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS. 8. Do not leave this equipment in an environment unconditioned where the storage temperature under -20C or above 60C, it may damage the equipment. 9. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. 10. Place the power cord such a way that people cannot step on it. Do not place anything over the power cord. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. 11. All cautions and warnings on the equipment should be noted. 12. If the equipment is not used for long time, disconnect it from the power source to avoid being damaged by transient over-voltage. 13. Never pour any liquid into ventilation openings. This could cause fire or electrical shock. 14. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. 15. If any of the following situations arises, get the equipment checked by service personnel:

a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. 5 d. The equipment does not work well or you cannot get it to work according to user manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 16. CAUTION: The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacture. Discard used batteries according to the manufacturers instructions. 17. If your computer is losing time significantly or the BIOS configuration resets itself to the default, the battery may have no power. Caution! 1. Do not replace battery yourself. Please contact a qualified technician or your retail provider. 2. The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. 18. CLASSIFICATION:

Supply Class I adapter No applied part Continuous Operation Not AP or APG category 19. Disconnect device: disconnect the power cord and battery to fully power off the device 20. Do not place the power cord where it is difficult to disconnect and may be stepped by other persons. 21. Follow national, state or local requirements to dispose of unit. 22. Maintenance: to properly maintain and clean the surfaces, use only the approved products or clean with a dry applicator. 23. Contact information:

No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei, Taiwan 114, R.O.C. TEL: +886 2-2792-7818 24. 25. This equipment shall not be used as a life support system. 26. Accessory equipment connected to the analog and digital interfaces must be in compliance with the respective nationally harmonized IEC standards (i.e. IEC 60950 for data processing equipment, IEC 60065 for video equipment, IEC 61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.) Furthermore all configurations shall comply with the system standard IEC 60601-1-1. Anyone who connects additional equipment to the signal input part 6 or signal output part is configuring a medical system, and is therefore, responsible that the system complies with the requirements of the system standard IEC 60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certified equipment in the patient environment and IEC 60XXX certified equipment outside of the patient environment. If in doubt, consult the technical services department or your local representative. 27. Users must not allow SIP/SOPs to come into contact with the patient at the same time. 28. The sound pressure level at the operators position according to IEC 704-1:1982 is no more than 70dB (A). 29. WARNING - Do not modify this equipment without authorization of the manufacturer. 30. WARNING To avoid risk of electric shock, this equipment must only be connected to a supply mains with protective earth. 31. WARNING: Please avoid having enclosure to contact with skin more than 1 minute. 32. CAUTION! This product: MIT-W102 is used with the Qualified and certificated power adapter:

Delta ELECTRONICS CO LTD, model MDS-060AAS19 B. Output: 19Vdc, 3.15A max DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. In case of serious incident that has occurred, please contact the manufacturer and local authorities immediately. Consignes de scurit 1. Lisez attentivement ces consignes de scurit. 2. Conservez ce manuel de l'utilisateur pour rfrence ultrieure. 3. Dbranchez cet quipement de la prise secteur avant de le nettoyer. N'utilisez 7 pas de dtergents liquides ou en arosol pour le nettoyage. 4. Pour les quipements enfichables, la prise de courant doit tre situe proximit de l'quipement et doit tre facilement accessible. 5. Gardez cet quipement l'abri de l'humidit. 6. Placez cet quipement sur une surface fiable pendant l'installation. Le faire tomber ou le laisser tomber peut causer des dommages. 7. Les ouvertures sur le botier sont destines la convection d'air. Protgez l'quipement contre la surchauffe. NE COUVREZ PAS LES OUVERTURES. 8. Ne laissez pas cet quipement dans un environnement non conditionn o la temprature de stockage est infrieure -20 C ou suprieure 60 C, cela pourrait endommager l'quipement. 9. Assurez-vous que la tension de la source d'alimentation est correcte avant de connecter l'quipement la prise de courant. 10. Placez le cordon d'alimentation de manire ce que personne ne puisse marcher dessus. Ne placez rien sur le cordon d'alimentation. La tension et le courant du cordon doivent tre suprieurs la tension et au courant indiqus sur le produit. 11. Tous les avertissements et avertissements sur l'quipement doivent tre nots. 12. Si l'quipement n'est pas utilis pendant une longue priode, dbranchez-le de la source d'alimentation pour viter d'tre endommag par une surtension transitoire. 13. Ne versez jamais de liquide dans les ouvertures de ventilation. Cela pourrait provoquer un incendie ou un choc lectrique. 14. N'ouvrez jamais l'quipement. Pour des raisons de scurit, l'quipement ne doit tre ouvert que par du personnel qualifi. 15. Si l'une des situations suivantes se produit, faites vrifier l'quipement par le personnel de service:

une. Le cordon d'alimentation ou la prise est endommag. b. Du liquide a pntr dans l'quipement. c. L'quipement a t expos l'humidit. r. L'quipement ne fonctionne pas bien ou vous ne pouvez pas le faire fonctionner conformment au manuel d'utilisation. e. L'quipement est tomb et est endommag. F. L'quipement prsente des signes vidents de casse. 16. ATTENTION: l'ordinateur est quip d'un circuit d'horloge en temps rel aliment par batterie. Il existe un risque d'explosion si la pile n'est pas remplace correctement. Remplacez uniquement par un type identique ou quivalent recommand par le fabricant. Jetez les piles usages conformment aux instructions 8 du fabricant. 17. Si votre ordinateur perd du temps de manire significative ou si la configuration du BIOS se rinitialise aux valeurs par dfaut, la batterie peut ne pas tre alimente. Mise en garde! 1. Ne remplacez pas la batterie vous-mme. Veuillez contacter un technicien qualifi ou votre revendeur. 2. L'ordinateur est quip d'un circuit d'horloge en temps rel aliment par batterie. Il existe un risque d'explosion si la pile n'est pas remplace correctement. Remplacez uniquement par un type identique ou quivalent recommand par le fabricant. Jetez les piles usages conformment aux instructions du fabricant. 18. CLASSIFICATION:

Adaptateur de classe I Aucune pice applique Opration continue Pas de catgorie AP ou APG 19. Dconnectez l'appareil: dbranchez le cordon d'alimentation et la batterie pour teindre compltement l'appareil. 20. Ne placez pas le cordon d'alimentation un endroit o il est difficile de le dconnecter et o d'autres personnes pourraient marcher dessus. 21. Respectez les exigences nationales, rgionales ou locales pour liminer l'unit. 22. Entretien: pour bien entretenir et nettoyer les surfaces, n'utiliser que les produits approuvs ou nettoyer avec un applicateur sec. 23. Coordonnes:

No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei, Tawan 114, R.O.C. TEL: +886 2-2792-7818 24. 25. Cet quipement ne doit pas tre utilis comme systme de survie. 26. L'quipement accessoire connect aux interfaces analogiques et numriques doit tre conforme aux normes CEI harmonises au niveau national respectives

(c'est--dire CEI 60950 pour les quipements de traitement de donnes, CEI 60065 pour les quipements vido, CEI 61010-1 pour les quipements de laboratoire et CEI 60601-1. pour les quipements mdicaux.) En outre, toutes les configurations 9 doivent tre conformes la norme systme CEI 60601-1-1. Quiconque connecte un quipement supplmentaire la partie d'entre de signal ou la partie de sortie de signal configure un systme mdical et est donc responsable de la conformit du systme aux exigences de la norme systme CEI 60601-1-1. L'unit est destine une interconnexion exclusive avec un quipement certifi CEI 60601-1 dans l'environnement du patient et un quipement certifi CEI 60XXX en dehors de l'environnement du patient. En cas de doute, consultez le service technique ou votre reprsentant local. 27. Les utilisateurs ne doivent pas permettre aux SIP / SOP d'entrer en contact avec le patient en mme temps. 28. Le niveau de pression acoustique au poste de conduite selon la CEI 704-1: 1982 nexcde pas 70 dB (A). 29. AVERTISSEMENT - Ne modifiez pas cet quipement sans l'autorisation du fabricant. 30. AVERTISSEMENT - Pour viter tout risque d'lectrocution, cet quipement ne doit tre connect qu' une alimentation secteur avec terre de protection. 31. AVERTISSEMENT: veuillez viter tout contact du botier avec la peau pendant plus d'une minute. 32. ATTENTION! Ce produit: MIT-W102 est utilis avec le Adaptateur secteur qualifi et certifi:

Delta ELECTRONICS CO LTD, modle MDS-060AAS19 B. Sortie: 19 Vdc, 3,15 A max AVIS DE NON-RESPONSABILIT: Cet ensemble d'instructions est donn conformment la norme CEI 704-1. Advantech dcline toute responsabilit quant l'exactitude des dclarations contenues dans ce document. En cas d'incident grave survenu, veuillez contacter immdiatement le fabricant et les autorits locales. Battery Safety RTC Battery Caution RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. 10 DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Do not place the battery incorrectly as this may cause danger of explosion. Dispose of used batteries according to the manufacturer's instructions. Do not dispose of batteries in a fire. They may explode. Check with local authorities for disposal instructions. Battery Pack Caution The battery used in this device may present a risk of fire or chemical burn if mistreated. Do not disassemble, heat above 40C, or incinerate. Replace standard battery pack with Advantech MIT-W102-BATC Li-ion 11.1V 2860mAh. Use of another battery may present a risk of fire or explosion. Dispose of used batteries according to local disposal regulations. Keep away from children. Do not disassemble and do not dispose of in a fire. Battery Charge Notice It is important to consider the environment temperature whenever you are charging the Lithium-Ion battery pack. The process is more efficient at normal room temperature or slightly cooler. It is essential that you charge batteries within the stated range of 0C to 35C. Charging batteries outside of the specified range could damage the batteries and shorten their charging life cycle. Storage and Safety Notice Although charge Lithium-Ion batteries may be left unused for several months, their capacity may be depleted due to the buildup of internal resistance. If this happens they will require recharging prior to use. Lithium-Ion batteries may be stored at temperatures between -20C to 60C, however they may be depleted more rapidly at the high end of this range. It is recommended to store batteries within normal room temperature ranges. Disposing of Batteries or Battery Pack. Batteries, battery packs, and accumulators should not be disposed of as unsorted household waste. Please use the public collection system to return, recycle, or treat them in compliance with the local regulations. Chapter 1 Ready to Go ............................................................................................. 14 1.1 Symbols Used in this Manual .................................................................................... 15 1.2 Product Features ........................................................................................................ 15 11 1.3 Package Contents ...................................................................................................... 15 1.4 System Configuration ................................................................................................ 16 1.6 Exploring the MIT-W102 ............................................................................................ 18 1.6.1 Front View .......................................................................... 18 1.6.2 Rear View ........................................................................... 19 1.6.3 Right View ........................................................................... 20 1.6.4 Left View ............................................................................ 20 1.6.5 Top View ............................................................................ 21 1.6.6 Bottom View ........................................................................ 21 Chapter 2 Making Connections................................................................................ 22 2.1 Connecting the Power ............................................................................................... 23 2.2 Connecting to a Monitor ........................................................................................... 23 2.3 Connecting USB Devices............................................................................................ 24 2.4 Connecting Headphones ........................................................................................... 24 2.5 Connecting a Microphone ......................................................................................... 25 Chapter 3 Turning On ............................................................................................... 26 3.1 Controlling the MIT-W102 ......................................................................................... 27 3.1.1 Using the Touch Screen ......................................................................................... 27 3.1.2 Using the Tap Function ............................................................ 27 3.1.3 Using the Control Panel Buttons ................................................. 27 3.1.4 Using the On-Screen Keyboard ................................................... 28 3.1.5 Adjusting Screen Brightness ...................................................... 31 3.1.6 Adjusting the Volume.............................................................. 32 Chapter 4 Wireless Connections ............................................................................. 33 4.1 Wi-Fi Connection ........................................................................................................ 34 4.2 Bluetooth Connections .............................................................................................. 37 4.2.1 Setting Up Bluetooth .............................................................. 37 Chapter 5 Advance Setting ...................................................................................... 41 12 5.1 Checking Battery Status ........................................................................................... 42 5.2 Maintenance ............................................................................................................... 42 5.2.1 Maintaining the Battery ........................................................... 42 5.2.2 Maintaining the LCD Display ...................................................... 43 5.2.3 Cleaning the MIT-W102 ............................................................ 43 5.3 Trouble Shooting ..................................................................... 43 Chapter 6 Dashboard and Hotkey setting ............................................................. 47 6.1 Dashboard.................................................................................................................... 48 6.2 NFC ............................................................................................................................... 48 6.2.1 NFC application .................................................................... 48 6.2.2 NFC Setting ......................................................................... 49 6.2.3 NFC Usage ........................................................................... 51 6.3 Camera ........................................................................................................................ 51 6.4 Brightness.............................................................................. 54 6.5 Hotkey Setting ........................................................................ 55 Appendix Specifications ........................................................................................... 56 A.1 Specifications ............................................................................................................. 57 A.2 Optional Accessories ................................................................................................. 59 A.2.1 External Battery ................................................................... 59 A.2.2 Office Docking Station ............................................................ 60 A.2.3 VESA Docking Station .............................................................. 64 A.2.4 Adjustable Stand (with the hand strap) ........................................ 66 A.2.5 Rubber Bumper ..................................................................... 69 A.3 Installing SSD .............................................................................................................. 71 13 Chapter 1 Ready to Go Congratulations on your purchase of the MIT-W102 Rugged Tablet PC. This product combines rugged design with reliable performance and powerful functionality to best suit all your needs, in a wide range of working conditions. This user manual outlines all you need to know to set up and use your MIT-W102. If you have any further questions or queries, contact our technical support team via our website:

14 http://www.advantech.com.tw/

1.1 Symbols Used in this Manual Denotes information that must be observed. Failure to do so may result in personal harm or damage to the product. Denotes information that must be observed. Failure to do so may result in personal harm or damage to the product. 1.2 Product Features Rugged design. Featuring with the Future Intel Pentium processor for intelligent system. Built-in WLAN/Bluetooth/NFC Durable, shock-resistant magnesium alloy housing. 10.1 WUXGA TFT LCD Power Requirements DC Input Voltage: 19 V Power Consumption: less than 60 W 1.3 Package Contents Ensure all the following items are present when you receive your MIT-W102. If any of these items are missing, contact your vendor immediately. Screens used in this manual are for illustrative purposes only. Actual screens may vary depending on your product version. 15 MIT-W102 Tablet PC AC power adaptor Battery Pack Warning! To prevent electric shock, Do not remove cover. Warning!

1. Input voltage rated 100-250 VAC, 50-60 Hz, 1.5-0.75 A, Output Voltage rated 19 VDC , max 3.15 A 2. Use a 11 Vdc @ 2860 mA lithium battery 3. Maintenance: to properly maintain and clean the surfaces, use only approved products or clean with a dry applicator Caution! 1. Do not replace battery yourself. Please contact a qualified technician or your retail provider. 2. The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. No user serviceable parts inside, refer servicing to qualified personnel. 1.4 System Configuration The block diagram of a MIT-W102 tablet computer is shown in the following diagram:

16 17 1.6 Exploring the MIT-W102 1.6.1 Front View 1 2 3 4 5 6 7 8 9 No. Component P1 Programmable Button P2 - Programmable Button Front Camera Power button Connected to expansion module DC-in jack Docking connector Projective capacitive multiple touch screen I/O ports USB 3.0 x 1 USB 2.0 x 1 Micro HDMI x 1 18 10 11 12 Audio x 1 Connectivity LED indicator Blue: when Wi-Fi is Turned on Green: when BT is Turned on HDD LED indicator Blinking blue: when hard disk drive is working Power / Battery LED indicator Green: Battery is fully charged (>95%) Amber : Battery is charging or Battery life is lower than 10%

1.6.2 Rear View No. Component 1 3 4 5 6 Back camera SSD cover Speaker Battery Battery Latch 19 7 NFC 1.6.3 Right View No. Component 1 Connected pin for expansion module 1.6.4 Left View 4 No. Component 1 2 I/O ports cover Audio Jack 20 3 4 5 USB 3.0 USB 2.0 Micro HDMI 1.6.5 Top View No. Component 1 2 3 Function buttons Built-in MIC Power button 1.6.6 Bottom View No. Component Docking connector AC-in jack 1 2 L 21 Chapter 2 Making Connections 22 2.1 Connecting the Power Before you can use your MIT-W102, you must fully charge the battery. Connect the power adapter as shown and leave to charge for:

A minimum of 2 hours when using the internal battery Condition: the operation time is based on the LCD backlight at 50% and the average utilization of the system under 10%. Installation Procedures:

1. Connect the female end of the power adapter to the DC-in of MIT-W102. 2. Connect the female end of the power cord to the DC power adapter. 3. Connect the 3-pin male plug of the power cord to an electrical outlet. NOTE: Be sure always handle the power cords by holding the plug ends only. To DC In of the equipment 2.2 Connecting to a Monitor You can connect the MIT-W102 to an external monitor for enhanced viewing. Connect one end of a HDMI to VGA cable to the Micro HDMI port on the left side of the MIT-W102.Connect the other end to the VGA cable and connect to the monitor. 23 2.3 Connecting USB Devices You can connect peripheral devices, such as a USB keyboard and mouse, as well as other wireless devices using the USB ports on the left side of the MIT-W102. 2.4 Connecting Headphones You can connect a pair of headphones using the headphone jack on the left side of the MIT-W102. 24 2.5 Connecting a Microphone The MIT-W102 features a built-in microphone, but you can still connect an external microphone if needed. Connect the microphone to the microphone jack on the left side of the MIT-W102 as shown. 25 Chapter 3 Turning On 26 1. Press and hold the power button to turn on the MIT-W102. 3.1 Controlling the MIT-W102 3.1.1 Using the Touch Screen The MIT-W102 is equipped with touch screen technology, for ease of use when you are on the go. Simply tap the screen with your finger to select icons and run applications. 3.1.2 Using the Tap Function When you tap on the screen with a pen or stylus, it emulates click functions of a regular mouse. To emulate a left click single tap the screen once. To emulate a right click tap and hold the screen. To emulate a double click, tap the screen twice. 3.1.3 Using the Control Panel Buttons The control panel buttons are located on the top side of MIT-W102. See below for a description of the two buttons and its function. Button Name Function Function Press to access your favorite programs Power Press to power on/off 27 3.1.4 Using the On-Screen Keyboard 1. Press and hold on the taskbar. 2. Enable show touch keyboard button 28 3. Tap the icon on the taskbar to open the keyboard 4. Use your finger or stylus pen to tap and enter letters, numbers and symbols as you would with a regular keyboard. To type capital letters tap the lock icon on the on-screen keyboard. a. To use handwriting, tap upper left button of On-Screen Keyboard. 29 b. Select the handwriting icon. c. Use your finger and stylus pen to write on screen. 30 3.1.5 Adjusting Screen Brightness 1. Tap on the right end of the taskbar to open the Action Center 2. Tap Brightness icon to adjust the brightness. 31 3.1.6 Adjusting the Volume 1. Tap the Volume icon on taskbar 2. Move the slide to adjust volume to tap the icon to mute 32 Chapter 4 Wireless Connections 33 4.1 Wi-Fi Connection Wi-Fi access requires a separate purchase of a service contract with a wireless service provider. Contact a wireless service provider for more information. The MIT-W102 comes pre-loaded with WLAN module; you can send and receive signals to a Wi-Fi network then synchronize files. A wireless network can be added either when the network is detected or by manually entering settings information. Before doing these steps, determine if authentication information is needed. 1. Click the wireless connection icon on the taskbar 2. Turn on Wi-Fi by tapping the icon 34 3. Available wireless access points will be shown once Wi-Fi is enabled. 4. Select the access point to connect with. 35 5. You may be prompted to enter a Security key for secure access. 6. The wireless connection is negotiated and the icon in the notification area shows a connected status whenever a wireless connection is present. 7. Airplane mode can be enabled to turn off Wi-Fi 36 4.2 Bluetooth Connections The MIT-W102 comes with built-in Bluetooth functionality that allows you to connect and communicate with other Bluetooth-enabled devices. 4.2.1 Setting Up Bluetooth Follow these instructions to set up a Bluetooth connection. 1. Type Bluetooth in Search and tap Bluetooth and other devices settings 2. Slide the icon to enable Bluetooth 37 3. When enabled, Bluetooth icon will be shown on the taskbar 4. Add more Bluetooth device by clicking on the icon +

38 5. Select Bluetooth 6. Select the Bluetooth device to connect from the available device menu 39 7. Comparing MIT-W102 with the Bluetooth device with Pass Key Entered 8. The Bluetooth device is successfully connected with MIT-W102 when the process is completed. It is recommended that you use a passkey to prevent unauthorized access to your MIT-W102. 40 Chapter 5 Advance Setting 41 5.1 Checking Battery Status As it is likely you will be using your MIT-W102 when out and about, it is important that you monitor the battery status regularly, to ensure you do not run out of power at a critical moment. 1. Tap on the Power icon on the taskbar to view detailed information and the battery screen appears. Best performance Favors performance over power Best battery life Saves energy by reducing MIT-W102s performance. 5.2 Maintenance If encounter any of system failure or serious incident in relation to device, please report to the manufacturer or local agent. 5.2.1 Maintaining the Battery Do not expose heat or attempt to disassemble the battery, and do not place the battery in water or in a fire. Do not subject the battery to strong impact, such as a blow from a hammer, or stepping on or dropping it. Do not puncture or disassemble the battery. Do not attempt to open or service the battery. Replace only with batteries designed specifically for this product. 42 Keep the battery out of reach of children. Dispose of used batteries according to local regulations. 5.2.2 Maintaining the LCD Display Do not scratch the surface of the screen with any hard objects. Do not spray liquid directly on the screen or allow excess liquid to drip down inside the device. Do not place anything, such as food and drink, on the screen at any time to prevent damage to the screen. Clean the LCD display only with a soft cloth dampened in the cleaning solutions each time after use. 5.2.3 Cleaning the MIT-W102 1. Turn off the MIT-W102 and unplug the power cord. 2. Wipe the screen and exterior with a soft, damp cloth moistened in the cleaning solutioins. Do not use liquid or aerosol cleaners on the screen, as these will discolor the finish and damage the screen. 5.3 Trouble Shooting When System behaves abnormally, such as 1. Failure to power on. 2. Failure to power off. 3. Power on LED off but DC power plug in. 4. Any other LEDs ON but system cannot work. Contact your distributer, sales representative, or Advantechs customer service center for technical support if you need additional assistance. Please have the following information ready before you call:

Product name and serial number. Descriptions of your peripheral attachments. Descriptions of your software (operating system, version, application software, etc.) A complete description of the problem. The exact wording of any error messages. 43 Symptoms, photo or video if available. Guidance and manufacturers declaration electromagnetic emissions The model MIT-W102 SERIES is intended for use in the electromagnetic environment specified below. The customer or the user of the model MIT-W102 SERIES should assure that it is used in such an environment. Emissions test Compliance Electromagnetic environment RF emissions CISPR 11 RF emissions CISPR 11 Harmonic emissions IEC 61000-3-2 Voltage fluctuations/

flicker emissions IEC 61000-3-3 guidance The model MIT-W102 SERIES uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment. The model MIT-W102 SERIES is suitable for use in all establishments, including domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes. Recommended separation distances between portable and mobile RF communications equipment and the model MIT-W102 Series The model MIT-W102 series is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the model MIT-W102 series can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the model MIT-W102 series as recommended below, according to the maximum output power of the communications equipment. Rated maximum output power Separation distance according to frequency of transmitter of transmitter m W 0,01 0,1 1 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2,5 GHz d = 1,2 d = 1,2 d = 2,3 0,12 0,38 1,2 0,23 0,73 2,3 0,12 0,38 1,2 44 10 100 3,8 12 3,8 12 7,3 23 For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. Guidance and manufacturers declaration electromagnetic immunity The model MIT-W102 SERIES is intended for use in the electromagnetic environment specified below. The customer or the user of the model MIT-W102 SERIES should assure that it is used in such an environment. IEC Compliance Electromagnetic environment guidance Immunity test 60601 level test level Conducted RF IEC 61000-4-6 Radiated RF IEC 61000-4-3 Portable and mobile RF communications equipment should be used no closer to any part of the model MIT-W102 SERIES, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter. Recommended separation distance 3 Vrms 150 kHz to 80 MHz 3 V/m 80 MHz to 2,5 GHz d = 1,2 Vrms d = 1,2 80 MHz to 800 MHz V/m d = 2,3 800 MHz to 2,5 GHz where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in meters (m). 45 Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, a should be less than the compliance level in each frequency range. b Interference may occur in the vicinity of equipment marked with the following symbol:

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the model MIT-W102 SERIES is used exceeds the applicable RF compliance level above, the model MIT-W102 SERIES should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the model MIT-W102 SERIES. b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than V/m. 46 Chapter 6 Dashboard and Hotkey setting 47 6.1 Dashboard Click on the shortcut to launch the dashboard 6.2 NFC 6.2.1 NFC application Click NFC icon to launch the application 48 6.2.2 NFC Setting

(1) Select COM port number 2

(2) Open Port 49

(3) Select Card Type

(4) Polling Start 50 6.2.3 NFC Usage NFC card can be detected when approaching the right hand side of the device 6.3 Camera

(1) Click Camera icon

(2) Default Rear Camera mode on the UI 51

(3) Switch Front / Rear Camera (Click camera icon to switch camera)

(4) Video Recording . Click video icon 52

(5) Click setting icon to change file name and path. 53 6.4 Brightness Click Brightness icon to adjust brightness 54 6.5 Hotkey Setting Click Hot Key Mode Setting and select function. E.g.: Set P1 key as WiFi ON / OFF key. 55 Appendix Specifications 56 A.1 Specifications Feature Description Operating System Microsoft Windows 10 IoT Enterprise LTSC Processor Max. speed Memory Storage Display Intel Pentium Processor N4200 Quad Core 1.1GHz ( Burst Frequency : 2.5GHz) LPDDR4 1600MHz 4GB on board memory 1 x m.2 SSD (Default 64GB / supports up to 128GB) 10.1 WUXGA TFT LCD Touch Panel P-CAP Multiple Touch One Power button Application Button Two Function programmable buttons for quick selection of applications Communication Bluetooth V5.0,V4.2, V4.1, V4.0 LE, V3.0+HS, Bluetooth 802.11a/b/g/n/ac WLAN built-in with integrated antenna Camera Main Battery V2.1+EDR system built-in with integrated antenna 2.0M Fixed Focus Camera at front 5.0M Auto Focus Camera with Flash LED at rear Rechargeable Li-ion battery (Advantech MIT101-BATC) Standard battery, 11.1V, 2860 mAh, 3S2P AC Adapter: AC 100V-250V 50/60Hz,1.5A(max) Medical Power Adapter Output : 19Vdc/3.15A(max)/60W, Auto Sensing/Switching worldwide power supply 57 Feature Description Security 1. Password security 2. TPM 2.0 One USB 3.0/ 2.0 One USB 2.0 One HP/MIC combined jack I/O Ports One Micro HDMI type D One DC-in jack One Expansion port 8-pin One Docking port 32-pin Audio Output One 1 watt speaker Physical Environment 295 x 196 x 20mm Approx. 1.1Kg (base configuration); approx. 2.43lbs Operational altitude: 3000 meters (700-1060hPa) Storage/Transportation altitude: 5000 meters (500-1060hPa) Operating Temperature:0C to 35C Storage/Transportation Temperature -20C to 60C Operating Humidity 10% ~ 95% @35C non-condensing Storage and Transportation Humidity 10%~95% @60C non-condensing 4ft drop onto concrete Feature Description Certification FCC Class B, CE, CB, UL Optional Device /

Accessories Office Docking Station (Optional) VESA Docking Station (Optional) Adjustable Stand (Optional) Rubber Bumper (Optional) 58 LED Status DUT AC Internal Green Amber Remark on/off adapter Battery LED LED in X V V V V V Off Off Off On On On X V V V V V Off Off On Off On Off On Off System Off Battery is charging Battery is fully charged

(100%) On Battery is charging Off Off On Battery is fully charged

(100%) Battery Low

(< 10 %) A.2 Optional Accessories A.2.1 External Battery You can use an external battery to extend the power of your MIT-W102. Battery specification: 2860 mAh, 11.1V A.2.1.2 Installing the External Battery 1. Align and insert the battery on the MIT-W102. 59 2. Lock to secure the battery once it is properly to be inserted. A.2.1.2 Removing the External Battery Repeat the above steps in reverse order to remove the battery. A.2.2 Office Docking Station You can use the office docking stand to dock the MIT-M101 when you are at your home or on your office desk. When docked, you can charge both the internal and external batteries or transfer data from your MIT-M101 to another PC. 60 Attach the MIT-M101 to the docking stand as shown. To charge the external battery, attach the battery to the docking stand as shown below. The external battery can also be charged when installed on the MIT-M101. 61 A.2.2.1 Docking Connectors See below for the rear view of the docking and a description of all ports and connectors. No. Component Function 1 2 3 4 5 Power jack Connect an RJ-45 cable to access LAN connection. LAN port USB port VGA port COM port Connect a serial cable to connect to another PC. Connect USB connectors to transfer data. Connect the AC adapter to charge the battery. Connect two devices (Input / Output). See below for the front view of the docking and a description of all ports and connectors. 62 No. 1 2 3 4 5 6 Lock mechanism (quick load/unload) Function USB port Microphone jack Headphone jack (Earphone Jack) Dock detection LED Battery bay status LED A.2.2.2 Connecting Power to the Docking Connect the AC power adapter to the docking and the mains as shown below. A.2.2.3 Docking Specifications Feature Description Feature Description Product Name MIT-W102 Docking Station Model Number MIT-W102-ACCDS One LAN port One COM port External I/O Interfaces One VGA port Two USB 2.0 host connectors One DC-in Power AC Adapter: AC 100V-250V 50/60Hz,1.5A(max) Output : 19Vdc/3.15A(max)/60W Physical Size 224.7 (H) x 200 (W) x 56.4 (D) mm 63 A.2.3 VESA Docking Station You can use the VESA docking station to dock the MIT-W102 to the place where you need via standard 75 x 75 mm VESA hole on rear side. When docked, you can transfer data from your MIT-W102 to another PC by COM port or USB port. Attach the MIT-W102 to the docking stand as shown. A.2.3.1 Docking Connectors See below for the rear view of the docking and a description of all ports and connectors. 64 No. Component Function 1 2 3 4 5 Power jack LAN port VGA port COM port USB port Connect the AC adapter to provide power. Connect an RJ-45 cable to access LAN connection. Connect to display for 2nd display output Connect a serial cable to connect to another PC. USB 2.0 port x 2 , Connect USB connectors to transfer data. See below for the front view of the docking and a description of all ports and connectors. No. 1 2 Function LED indication / Device connected Standard 75x75 VESA hole A.2.3.2 Connecting Power to the Docking Connect the AC power adapter to the docking and the mains as shown below. 65 A.2.3.3 Docking Specifications Feature Description Feature Description Product Name MIT-W102 VESA Docking Model Number MIT-W102-ACCVD One LAN port One COM port External I/O Interfaces One VGA port Two USB 2.0 host connectors One DC-in Power AC Adapter: AC 100V-250V 50/60Hz,1.5A(max) Output : 19Vdc/3.15A(max)/60W Physical Size 224.7 (H) x 200 (W) x 56.4 (D) mm A.2.4 Adjustable Stand (with the hand strap) You can use the adjustable stand to provide desk support when you are at home or in your office. 66 A.2.4.1 Attaching the Adjustable Stand 1. Fasten four screws to attach the 3-in-1 multi-functional back cover to your MIT-M101 with or without rubber bumpers attached to the tablet. 2. Pull to adjust the stand to desirable angle. 67 A.2.4.2 How to install the hand strap on the stand 1. Pass the end of the hand strap through the outer hole on each side of the stand 2. Pass the end of the hand strap through the inner hole on each side of the stand and stick the hand strap together 3. Check if the length of the hard strap is OK. 68 A.2.5 Rubber Bumper A.2.5.1 Installing the Rubber Bumpers To protect the housing case of MIT-W102, install the rubber bumpers. 1. Install the rubber bumpers on the left and right side of the MIT-W102. 2. Make sure the rubber bumpers are aligned and locked on the indents. 3. Screw the rubber bumpers on left and right properly into the MIT-W102. The Rubber bumper could provide well drop protection when device fall from high place. Please assure the rubber was put on the right position and the screws was fastened when install the bumper on device. 69 A.2.5.2 Removing the Rubber Bumpers 1. Unscrew the rubber bumpers from the rear of the tablet PC. 2. Remove the rubber bumpers on the left and right. 70 A.3 Installing SSD Inserting SSD You can insert an SDD to store data, which needs to be later transferred to another machine, or to simply expand the storage capacity of the MIT-W102. 1. Open the SSD card compartment cover. 2. Insert the SDD, facing upwards, until it clicks into place. Screw and fix SSD 3. Screw and fix the shielding case. 71 4. Close the SDD compartment cover. Removing SSD 1. Open the SSD compartment cover. 2. Unscrew and remove the shielding case 72 3. Unscrew and remove SSD from the slot. 4. Close and screw the SSD card compartment cover. 73

( : http://www.advantech.com ADVANTECH ea AD\ANTECH pL BUGS): TEA a BRA TAG 19 BRS Enter meh) COMPUTER/ & fis (Zit HA) FC EC MODEL NAME #2 5:(2!-5) : MIT-W102 INPUT 48 A (48) : 19V === 3.15A This device complies with the requirements in part 15 of FCC cies FACTORY: T5 Operation is subject to the following two conditions: (1) This device Sify may not cause harmful interference, and (2) This device must accept SK mevicat-senenn meoicaL eouirment any interference received, including interference that may cause AS TO ELECTRICAL SHOCK, FIRE AND MECHANICAL undesired operation. c US HAZARDS ONLY IN ACCORDANCE WITH oP A .: . ANSUAAMI ES60601-1 (2005) + AMD 1(2012) ATTENTION: Pour viter tout risque dlectrocution, ne pas enlever le couvercle, CAN/CSA-C22.2 No. B0601-1:14 Aucune pice rparable par l'utilisateur ne se trouve a l'intrieur, aya Confier tout entretien a un personnel qualifi uniquement. FCC ID: M82-MITW102, IC ID: 9404A-MITW102 Contains FCC ID: PPD-QCNFA364AH, IC ID: 4104A-QCNFA364A, Only use the adapter . Delta Electronics, Inc. Type: MDS-O60AAS19 B Caution!

INPUT: 100-250V ~ 1.5-0.75A 50-60Hz To prevent shock. Do not remove cover. OUTPUT: 19V === 3.15A No user serviceable parts inside. Refer /

MADE IN TAIWAN 4 83238( 8B fili&) servicing to qualified personnel. fo http://www.advantech.com ADVANTECH Co.Ltd AD\ANTECH 458): BE RPS CTE RRS) BAER RSH) COMPUTER/ %i( #420 it 4) MODEL NAME S/8R(2! 8) : MIT-W102 INPUT #8. (18) : 19V =

FACTORY: TS mene sowaA mena aaron nyinterforene rose, eluding intrernce that may ese

{Stonemea sot recto mectaWcAL tinder operation Wes caerraieecsttens Ib cain ATTENTION: Por trot eae conc pt encom acne pce oar pr late he Goo 3 ite. ene tut etretien 8 un persnmel ai uniquement. Focib: Mez.MrTwa, 110: 944A sTO102 (Contain FCC ID: PO-QCNFASG4AM, I ID: 41044-QCNFAIGAA Only us the adapter Delta Elctronles, Ine. Type: MDS-O60AAS19 B gee Chvers ena men OUTPU 19V =~ 3.358. MADE IN TAIWAN fA (498 18)

( : http://www.advantech.com ADVANTECH ea AD\ANTECH pL BUGS): TEA a BRA TAG 19 BRS Enter meh) COMPUTER/ & fis (Zit HA) FC EC MODEL NAME #2 5:(2!-5) : MIT-W102 INPUT 48 A (48) : 19V === 3.15A This device complies with the requirements in part 15 of FCC cies FACTORY: T5 Operation is subject to the following two conditions: (1) This device Sify may not cause harmful interference, and (2) This device must accept SK mevicat-senenn meoicaL eouirment any interference received, including interference that may cause AS TO ELECTRICAL SHOCK, FIRE AND MECHANICAL undesired operation. c US HAZARDS ONLY IN ACCORDANCE WITH oP A .: . ANSUAAMI ES60601-1 (2005) + AMD 1(2012) ATTENTION: Pour viter tout risque dlectrocution, ne pas enlever le couvercle, CAN/CSA-C22.2 No. B0601-1:14 Aucune pice rparable par l'utilisateur ne se trouve a l'intrieur, aya Confier tout entretien a un personnel qualifi uniquement. FCC ID: M82-MITW102, IC ID: 9404A-MITW102 Contains FCC ID: PPD-QCNFA364AH, IC ID: 4104A-QCNFA364A, Only use the adapter . Delta Electronics, Inc. Type: MDS-O60AAS19 B Caution!

INPUT: 100-250V ~ 1.5-0.75A 50-60Hz To prevent shock. Do not remove cover. OUTPUT: 19V === 3.15A No user serviceable parts inside. Refer /

MADE IN TAIWAN 4 83238( 8B fili&) servicing to qualified personnel. fo http://www.advantech.com ADVANTECH Co.Ltd AD\ANTECH 458): BE RPS CTE RRS) BAER RSH) COMPUTER/ %i( #420 it 4) MODEL NAME S/8R(2! 8) : MIT-W102 INPUT #8. (18) : 19V =

FACTORY: TS mene sowaA mena aaron nyinterforene rose, eluding intrernce that may ese

{Stonemea sot recto mectaWcAL tinder operation Wes caerraieecsttens Ib cain ATTENTION: Por trot eae conc pt encom acne pce oar pr late he Goo 3 ite. ene tut etretien 8 un persnmel ai uniquement. Focib: Mez.MrTwa, 110: 944A sTO102 (Contain FCC ID: PO-QCNFASG4AM, I ID: 41044-QCNFAIGAA Only us the adapter Delta Elctronles, Ine. Type: MDS-O60AAS19 B gee Chvers ena men OUTPU 19V =~ 3.358. MADE IN TAIWAN fA (498 18)

http://www.advantech.com ADVANTECH Co.,Ltd |

D\ANTECH els (BIH): SER (9 5 ORS (EAD OR ZS A) Han 8 A Bh) COMPUTER/ & fii (it BA) FC C MODEL NAME 2! 54: (2!-5) : MIT-W102 V a INPUT #4 A (#1 A) : 19V === 3.15A This device complies with the requirements in part 15 of FCC Rules:

FACTORY: T5 Operation is subject to the following two conditions: (1) This device apssity may not cause harmful interference, and (2) This device must accept Le) 4 MEDICAL-GENERAL MEDICAL EQUIPMENT any interference received, including interference that may cause AS TO ELECTRICAL SHOCK, FIRE AND MECHANICAL undesired operation. Cc US HAZARDS ONLY IN ACCORDANCE WITH - . ANSI/AAMI ES60601-1 (2005) + AMD 1 (2012) ATTENTION: Pour viter tout risque dlectrocution, ne pas enlever le couvercle. le Aucune pice rparable par l'utilisateur ne se trouve a l'intrieur. CAN/CSA-C22.2 No. 60601-1:14 4Ly4 ae ee Confier tout entretien a un personnel qualifi uniquement. RS STRRRL ESA TELE LElB Boe Contains FCC ID: TX2-RTL8822CE, IC ID: 6317A-RTL8822CE Only use the adapter -

Delta Electronics, Inc. Type: MDS-OG0AAS19 B Caution!

INPUT: 100-250V ~ 1.5-0.75A 50-60Hz To prevent shock. Do not remove cover. }

OUTPUT: 19V === 3.15A No user serviceable parts inside. Refer

\ MADE IN TAIWAN 4382238(4 @#li&) servicing to qualified personnel. Va

http://www.advantech.com ADVANTECH Co.,Ltd |

D\ANTECH els (BIH): SER (9 5 ORS (EAD OR ZS A) Han 8 A Bh) COMPUTER/ & fii (it BA) FC C MODEL NAME 2! 54: (2!-5) : MIT-W102 V a INPUT #4 A (#1 A) : 19V === 3.15A This device complies with the requirements in part 15 of FCC Rules:

FACTORY: T5 Operation is subject to the following two conditions: (1) This device apssity may not cause harmful interference, and (2) This device must accept Le) 4 MEDICAL-GENERAL MEDICAL EQUIPMENT any interference received, including interference that may cause AS TO ELECTRICAL SHOCK, FIRE AND MECHANICAL undesired operation. Cc US HAZARDS ONLY IN ACCORDANCE WITH - . ANSI/AAMI ES60601-1 (2005) + AMD 1 (2012) ATTENTION: Pour viter tout risque dlectrocution, ne pas enlever le couvercle. le Aucune pice rparable par l'utilisateur ne se trouve a l'intrieur. CAN/CSA-C22.2 No. 60601-1:14 4Ly4 ae ee Confier tout entretien a un personnel qualifi uniquement. RS STRRRL ESA TELE LElB Boe Contains FCC ID: TX2-RTL8822CE, IC ID: 6317A-RTL8822CE Only use the adapter -

Delta Electronics, Inc. Type: MDS-OG0AAS19 B Caution!

INPUT: 100-250V ~ 1.5-0.75A 50-60Hz To prevent shock. Do not remove cover. }

OUTPUT: 19V === 3.15A No user serviceable parts inside. Refer

\ MADE IN TAIWAN 4382238(4 @#li&) servicing to qualified personnel. Va

Advantech Co., Ltd. 26 20 1 No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei 114, Taiwan, R.O.C. Tel:886-2-7732-3399 Fax:886-2-2794-7334 WWW.advantech.com.tw To:

Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 From: Advantech Co Ltd No. 1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei 114, Taiwan Regarding:

Confidentiality Request regarding application for FCC ID: M82-MITW102 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Name (Printed): Lily Huang Signature:

On behalf of Company: Advantech Co Ltd Telephone: 886-2-7732-3399 E-mail: Lily.Huang@advantech.com.tw

Advantech Co., Ltd. 26201 No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei 114, Taiwan, R.O.C. Tel:886-2-7732-3399 Fax:886-2-2794-7334 WWW.advantech.com.tw Date: 2022-09-12 Nemko North America, Inc. 303 River Road, Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Kevin Tsai / Manager of Compliance Certification Services to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with Advantech Co.Ltd.. Yours sincerely, ____________________ Signatory Name: Lily Huang Company Name: Advantech Co.Ltd. Address: No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei 114, Taiwan Tel: +886-2-7732-3399 Fax: +886-2-2794-7334 Email: Lily.Huang@advantech.com.tw