submitted | available | document details (if available) | source link |
---|---|---|---|
various | 8-18-253en | Users Manual | 1.37 MiB |
Important Instructions Subject: 204689 Wireless Network Kits Use With: Single Washer or Dryer and Stack Washer/Dryer or Stack Dryers Starting February 2019 WARNING Kit No. 204689 consists of:
This kit is to be installed in accordance with the manufacturers instructions and all codes and re-
quirements of the authority having jurisdiction. In Canada, this conversion/installation shall be carried out in accordance with the requirements of the pro-
vincial authorities having jurisdiction and in accord-
ance with the requirements of the CAN/CGA-B149.1 and CAN/CGA-B149.2 installation code. Failure to follow instructions could result in serious injury, death or property damage. The qualified agency per-
forming this work assumes all responsibility for this kit installation. W013R4 WARNING To reduce the risk of electric shock, fire, explosion, serious injury or death:
Disconnect electric power to the machine before Close gas shut-off valve to the machine before Close steam gate valve to the machine before Never start the machine with any guards/panels servicing. servicing. servicing. removed. Whenever ground wires are removed during serv-
icing, these ground wires must be reconnected to ensure that the machine is properly grounded. 1 1 2 2 1 1 1 1 1 807211 F8674006 D503661 55881 204732 F8673901 204692 807428 8-18-253EN Wireless Network Control Assembly Wireless Network Harness Screws Wire Ties Conversion Label Network Option Diagram Wireless Control Label Compliance Jumper Kit Instructions Special Tools required for this kit:
Magnetic 5/16 in. Socket IMPORTANT: This kit must be installed by a qualified service person. NOTE: Refer to appropriate service manual to aid in the installation of this kit. IMPORTANT: When reference is made to directions
(right or left) in this instructions, it is from operator's position facing front of machine. FCC COMPLIANCE STATEMENT CAUTION W017 Changes or modifications not expressly approved could void your authority to use this equipment . This device complies with Part 15 of the FCC Rules. Operation to the following two conditions: (1) This device may not cause Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT 1 Form No. 8-18-253EN December 2018 harmful interference, and (2) this device must accept any interfer-
ence received, including interference that may cause undesired operation. INDUSTRY CANADA STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The 807211 Wireless Network Control Assembly maintains a separation distance great-
er than or equal to 2.5 cm which is intrinsic to the installation as described in this manual. Rear Control Single Washer or Dryer 1. IMPORTANT - Disconnect electrical power to machine. Control will not recognize network board until power is cy-
cled to machine. 2. Remove two control panel attaching screws and lay assembly forward on protective padding. NOTE: There are four tabs located on backside of con-
trol panel frame. Only the two tabs closest to the con-
trol must be bent upward. Refer to Figure 1 and Figure 2 . 1 2 3 Topload Washer Illustrated 1 TLW1683K 1. Do Not Bend Figure 2 4. Place 807428 Compliance Jumper on the appropriate pins on header "H1". Note that the board will operate at reduced pow-
er if this step is skipped. Refer to Figure 11 . 5. Remove double sided tape backing from 807211 Wireless Network Control Assembly. 6. Position 807211 Wireless Network Control Assembly so that the mounting tabs on the Network Board go in front of the tabs on the control panel and the assembly mounts to the right of the mounting tabs, as shown in Figure 3 . (The control should be to the right of the mounting tabs.) Then attach using the (2) D503661 Screws. Refer to Figure 3 . 1. Screwdriver 2. Pliers 3. Tabs TLW1682K Figure 1 1 3. Use a flat blade screwdriver and slightly bend each tab up on-
ly far enough to allow getting the jaws of a pliers under each tab and bend to 90 degrees. Make sure each tab is bent up square and straight. IMPORTANT: Be careful not to damage control panel overlay when prying up tabs. 1. D503661 Screws Figure 3 TLW1680K_SVG Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT 2 Form No. 8-18-253EN 7. Install F8674006 Wireless Network Harness between network board "H3" and the electronic control "H1". Refer to Figure 4 . 8. Secure the F8674006 Wireless Network Harness using the (2) 55881 Wire Ties as shown in Figure 4 . 9. Place F8673901 Network Option Diagram in control cabinet with existing diagrams. 10. Place 204692 Wireless Control Label in the control hood be-
hind the control panel. Topload Washer Illustrated 11. Fill out and place 204732 Conversion Label in control hood behind control panel. 12. Reconnect electrical power to the machine. NOTE: The machine control MUST have been powered down prior to connecting the wireless control assem-
bly in order for the control to recognize the board and to allow communication with it. 1. "H1"
2. 55881 Wire Ties 3. "H3"
4. 807211 Wireless Network Control Assembly 5. F8674006 Wireless Network Harness 6. Electronic Control Figure 4 Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT 3 Form No. 8-18-253EN Front Control Single Washer or Dryer 1. IMPORTANT - Disconnect electrical power to machine. Control will not recognize network board until power is cy-
cled to machine. 2. Open access panel to gain access to the control area. Refer to Service Manual. 3. Place 807428 Compliance Jumper on the appropriate pins on header "H1". Note that the board will operate at reduced pow-
er if this step is skipped. Refer to Figure 11 . 4. Install the F8674006 Wireless Network Harness between the network board "H3" refer to Figure 6 , and the electronic con-
trol "H1". Refer to Figure 7 . 5. Remove double sided tape backing from 807211 Wireless Network Control Assembly. 6. Place the tab on 807211 Wireless Network Control Assembly into slot in front bulkhead and secure opposite end with one D503661 Screw. Refer to Figure 5 . Washer Illustrated Washer Illustrated 1 2 4 3 FLW226K_SVG 1. Electronic Control 2. "H1"
3. "H3"
4. F8674006 Wireless Network Harness Figure 6 1. 807211 Wireless Network Control Assembly 2. Slot 3. D503661 Screw Figure 5 Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT 4 Form No. 8-18-253EN Washer Illustrated D503661 Screw. Refer to Figure 8 . Repeat for installing sec-
ond network board. 1 2 3 1 2 1. Electronic Control 2. "H1"
3. F8674006 Wireless Network Harness Figure 7 FLW227K 4 3 SWD273K_SVG 1. 807211 Wireless Network Control Assembly (Washer) 2. Slot 3. 807211 Wireless Network Control Assembly (Dryer) 4. D503661 Screws 7. Place F8673901 Network Option Diagram in control cabinet with existing diagrams. Figure 8 8. Place 204692 Wireless Control Label in control cabinet be-
1 hind control panel. 9. Fill out and place 204732 Conversion Label in control cabinet 2 located behind control panel. 10. Close access panel. 11. Reconnect electrical power to the machine. NOTE: The machine control MUST have been powered down prior to connecting the wireless control assem-
bly in order for the control to recognize the board and to allow communication with it. Front Control Stack Washer/Dryer or Stack Dryer 1. IMPORTANT - Disconnect electrical power to machine. Control will not recognize network board until power is cy-
cled to machine. 2. Open access panel to gain access to the control area. Refer to Service Manual. 3. Place 807428 Compliance Jumper on the appropriate pins on header "H1". Note that the board will operate at reduced pow-
er if this step is skipped. Refer to Figure 11 . 4. Remove double sided tape backing from 807211 Wireless Network Control Assembly. 5. Place tab on 807211 Wireless Network Control Assembly into slot in front bulkhead and secure opposite end with one 6. Install F8674006 Wireless Network Harness between network board "H3", refer to Figure 9 , and electronic control "H1". Refer to Figure 10 . 1 2 3 5 4 SWD274K_SVG 1. "H3"
2. Electronic Control (Washer) 3. Electronic Control (Dryer) 4. "H3"
5. F8674006 Wireless Network Harness Figure 9 Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT 5 Form No. 8-18-253EN 7. Add one 55881 Wire Tie to backside of electronic control as shown in Figure 10 . 8. Place F8673901 Wiring Diagram in control cabinet with ex-
isting diagrams. 9. Place 204692 Wireless Control Label in the control cabinet. 10. Fill out and place 204732 Conversion Label in control cabinet located behind control panel. 11. Reconnect electrical power to the machine. NOTE: The machine control MUST have been powered down prior to connecting the wireless control assem-
bly in order for the control to recognize the board and to allow communication with it. NOTE: Refer to network installation manual for ma-
chine connections to network. 2 3 1 7 1. Electronic Control (Dryer) 2. Electronic Control (Washer) 3. Tape 4. "H1" Connection (Washer) 5. F8674006 Wireless Network Harness 6. 55881 Wire Tie 7. "H1" Connection (Dryer) 4 5 6 SWD275K Figure 10 Compliance Jumper (H1) The 807428 Compliance Jumper is used to enforce limits set by local agencies on WiFi channel usage and output power. This jumper must be placed on the pins described in this section that correspond to the location where the Wireless Network Control will be operated. If the jumper is set incorrectly, the Wireless Network Control will be out of compliance with local agencies. If the jumper is not set at all, the Wireless Network Control will Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT 6 Form No. 8-18-253EN operate at a reduced power-level, which will reduce the perform-
ance of the Wireless Network Control. NOTE: It is the responsibility of the installer to make sure that the Compliance Jumper is set to meet local standards. Incorrect settings will cause the board to be out of compliance and may lead to reduced range and loss of WiFi channels. The 807428 Compliance Jumper must be placed in one of three locations on header "H1". The three locations are shown in the table below and also in Figure 11 . Region US/North America EU JP 807428 Jumper Lo-
cation H1 Pins 9 & 10 Left Most Posi-
tion Second From Left 7 & 8 5, 7, 6 Third From Left 1 2 3 COM238K 1. US/North America 2. EU 3. JP Figure 11 Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT 7 Form No. 8-18-253EN
This product uses the FCC Data API but is not endorsed or certified by the FCC