FCC ID: 2A6V5AMZ02 MultiSensor

MultiSensor User Manual AMZ02 Key Features:

Z-Wave 800 series design, support Z-wave LR and compatible with Z-Wave Mesh 1 mile under LR mode, up to 200 feet under Z-wave mesh mode Automate your home intelligently by 3 essential pieces of environment data measurement Up to 8 meters infrared detecting distance, and wide angle range of 120 Supports more preprogrammed applications Low Battery Indication Good to install on wall, intended for residential as well as commercial applications Physical Characteristics Fresnel Lens LED Indicator Rear Cover Magnetic Base Figure 1 Action Button Battery Slot Figure 2 Optimally Installing MultiSensor MultiSensor has been designed to be mounted on the coner of the wall indoors. To optimally install it, please note the following. MultiSensor should NOT be installed in areas of artificial temperature change that would impact the accuracy of the sensors. When selecting a location, avoid placing it beside or near air conditioners, humidifiers, and heaters, and avoid positioning it directly opposite a window or direct sunlight. For optimal performance, your MultiSensor should NOT be mounted directly on or near metal framing or other large metallic objects. Large metal objects may weaken the Z-Wave wireless signal. Ensure therere no obstacles in front of the lens of MultiSensor. Otherwise, the detection result may be inaccurate. Install MultiSensor where persons may be detected to cross. The double sided tape and screws are optional to be used to fix the Magnetic Base on the wall. Recommend to place the sensor approx 2.5 meters above the ground. As shown on below figure 3 and figure 4. Figure 3 Figure 4 Power MultiSensor Turn the Rear Cover counter-clockwise and open it. Place the CR123A battery in the battery slot to power on your MultiSensor, pay attention to the positive and negative polars. When MultiSensor is powered on, The LED will be colorful gradient alternately for 2 cycles and then off when not connected to a Z-Wave Controller upon initial power. Adding(Inclusion) Follow the instructions for your Z-Wave Certified Controller adding inclusion mode.When prompted by the controller. 1. The MultiSensor should be within 10 of your Z-Wave controller for the inclusion process. After successful pairing, the device can be brought to the desired location. 2. Set the main controller into (security/non-security) adding mode (see the controllers manual). 3. Press the Action Button 3 times for device inclusion.The LED Indicator will flash green five times indicating inclusion successful, then it fails to be included, you need to repeat the above process. 4. If your Z-Wave gateway support SmartStart: scan the QR code on MultiSensor using the gateways app.Your sensor will join your Z-Wave network automatically. Removing(Exclusion) Follow the instructions for your Z-Wave Certified Control enter exclusion mode. When prompted by the controller. 1.Remove the Rear Cover. 2.Set the controller into Removing mode(see the controllers manual). 3.Press the Action Button quickly 3 times in a row. The LED Indicator will blink red 5 times and then off indicating exclusion successful. Resetting the MultiSensor If needed, the MultiSensor can be reset locally by following these steps. Only do this when your Z-Wave controller is disconnected or otherwise unreachable. Beware that resetting your device will disconnect it from the system. 1.Remove the Rear Cover and confirm that your MultiSensor is powered on. 2.Press and hold Action Button for 12 seconds then release. A flashing light with red and green two colors alternately in 5 seconds indicates a successful factory reset. 3.The MultiSensors memory will be erased to factory settings. Waking Up the MultiSensor MultiSensor is a battery powered device, it wakes up on regular intervals to give battery and other status updates to the controller, as well as to accept configuration settings from the controller. This helps to extend the battery life. The device can be forced to wake up to submit these reports or accept new settings immediately by simply pressing and holding the Action Button for three seconds. The LED Indicator will flash blue once indicating successful wake up. Warranty. The Warranty is provided by Ally (hereinafter Manufacture). The Manufacture warrants devices to be free from manufacturing defects for a period of 12 months from the original date of consumer purchase. In line with the terms of sales between the Manufacture and the authorized importer / reseller of this device, any claims against the foregoing warranty are to be handled by the authorized distributor / reseller directly. The foregoing warranty is subject to the proper installation, operation, and maintenance of the device in accordance with installation instructions and the operating manual supplied to customer and further documentation made available digitally. The Manufacture does not warrant against normal wear and tear, nor damage caused by accident or abuse. Please be sure to read this devices support notes, digital materials, and quick start guide fully. Subject to the full terms of obtaining service within 30 days of the manifestation of a problem, if you submit a valid claim under this warranty, the Manufacture shall provide further information in obtaining warranty services from the authorized importer and / or seller of this device. Declaration of Conformity. MultiSensor is in compliance with the essential requirements and other relevant provisions of RED 2014/53/EU, RoHS 2011/65/EU, IEC62321:2008 and EN50581:2012. FCC Caution:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Page 1 of 1 FCC ID: 2A6V5AMZ02 LABEL AND LOCATION MultiSensor Model: AMZ02 FCC ID: 2A6V5AMZ02

(Size: L: 1.5cm x W: 1.5cm) Label Location Shenzhen LCS Compliance Testing Laboratory Ltd. Add: 101, 201 Bldg A & 301 Bldg C, Juji Industrial Park Yabianxueziwei, Shajing Street, Baoan District, Shenzhen, 518000, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

Ally Technology (Shenzhen) Co.,Ltd Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 3/10/2023 Ally Technology (Shenzhen) Co.,Ltd acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought (FCC ID: 2A6V5AMZ02):

Name of U.S. agent: Tim Payne Company U.S. agent: FCC US Agent, LLC Physical U.S. address of agent: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA FRN of U.S. agent: 0033402884 Email address of U.S. agent: Support@FCCUSAgent.com Phone of U.S. agent: 708-571-3148 FCC US Agent, LLC acknowledges their obligation to accept service of process on behalf of Ally Technology (Shenzhen) Co.,Ltd. Ally Technology (Shenzhen) Co.,Ltd accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). Sincerely, Signature Scott ding Manager Ally Technology (Shenzhen) Co.,Ltd Signature Tim Payne Manager FCC US Agent, LLC The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC. 3 0 V

, U

) 7

) d

1 1 9

. 2 _ t n e g A _ S U

l e d o m

_ 8 4

Ally Technology (Shenzhen) Co.,Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023/3/13 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2A6V5AMZ02 Ally Technology (Shenzhen) Co.,Ltd (Scott ding) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Scott ding Rev 1/26/2023 Ally Technology (Shenzhen) Co.,Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023/3/13 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2A6V5AMZ02 Ally Technology (Shenzhen) Co.,Ltd (Scott ding) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, Scott ding Rev 1/26/2023

Ally Technology (Shenzhen) Co.,Ltd Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2A6V5AMZ02 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram Schematics Operational Description File Name Block Diagram.pdf Schematic.pdf Operation Description.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely,

Scott ding Rev 11/20/07

Ally Technology (Shenzhen) Co.,Ltd Model difference statement It is hereby declared that the product Product Name: MultiSensor Model: AMZ02 Listed Model(s): AMZ01 Mark: Ally PCB board, structure and internal of these model(s) are the same. Sincerely, Signature

[Scott ding]

[Manager]

[Ally Technology (Shenzhen) Co.,Ltd]

version01

Ally Technology (Shenzhen) Co.,Ltd Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date:

SUBJECT: FCC Application for (FCC ID: 2A6V5AMZ02) To Whom It May Concern:

We, the undersigned, hereby authorize Gavin Liang at Shenzhen LCS Compliance Testing Laboratory Ltd. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Shenzhen LCS Compliance Testing Laboratory Ltd.on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards,

Scott ding M:\Master Documents\TEMPLATES\POA_Letter.doc

Ally Technology (Shenzhen) Co.,Ltd Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2023/3/13 SUBJECT:

To Whom It May Concern:

I, the undersigned, hereby states this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, and will apply the Supplier's Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. I understand the following FCC requirements:

1. Devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the

"accredited" option to search for FCC recognized accredited test firms.) 2. Pt 2.1077 contains the list of information that must be included in the Supplier's Declaration of Conformity, which must be supplied with each product sold. The SDoC compliance info shall be included in the Users Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(b), the responsible party is either the Manufacturer or if the product is imported the Importer. Regards, Ally Technology (Shenzhen) Co.,Ltd

Scott ding