OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 OEM/Integrators Installation Manual Version Issue date Changes 0.1 0.2 0.3 0.4 0.5 0.6 Initial Version 2015/9/04 2015/10/22 Update GPIO sharing scheme 2015/11/30 Update package information. Correct PERST_N 2015/12/1 2016/10/15 GPIO : Link2 change to UART_TXD2 2017/5/18 Update industrial and commercial grade information Update FCC approval information, Correct GPIO 27, 28, 29 Remark IMPORTANT should not be disclosed to third parties without prior written consent of amazipoint technology Ltd. This document contains important Information and therefore Address2F, No. 113, Zhongyang Rd., Xindian Dist., New Taipei City, Taiwan(R.O.C) Signature:
Author:
Martin Ho www.amazipoint.com Reviewed by:
Approved by:
Remarks:
Copyright amazipoint technology Ltd. All rights are reserved. Page 1 of 13 OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 W708 module is designed for easy-design-in low cost Wifi applicationIt has WAN, LAN, UART, I2C, 1. Introduction SPI, I2S, SDXC and GPIO interfaces. Support 1T1R 150N operation. 3.3V single power supply. There are industrial grade and commercial grade two different configuration. For industrial grade, we use industrial grade DDR2 memory. component. For commercial grade, we use commercial grade DDR2 memory. component. RF 0 8MB SPI FLASH MT7688AN 2 B2B Socket 3.3V 40MHz Crystal 64MB DDR2 1.8V 1.8V switching regulator 2. Technical specification a. Channel Plan country code region channel 0 North America 1 5 6 7 CH1 ~ 11 Others CH1 ~ 13 Japan CH1 ~ 14 CH3 ~ 9 CH5 ~ 13 Copyright amazipoint technology Ltd. All rights are reserved. Page 2 of 13 OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 Note : The country code is configured before shipping and can not be changed by user. b. Specification Table Items Specification Supported Standard and Protocol IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u, CSMA/CA, CSMA/CD,TCP/IP,DHCP, ICMP, NAT, PPPoE Dimension 35*25 mm Power consumption
< 250mA, 180mA typical Operating Temperature Range Storage Temperature Range Humidity
-30 ~ 80 deg. C ( for commercial grade )
-40 ~ +85 deg. C ( for industrial grade )
-40 ~ 90 deg. C
< 90%
WAN Port one 10/100M adaptive RJ45 port LAN Port one 10/100M adaptive RJ45 port RF Parameters Range 2.412~2.472GHz Frequency 2.412~2.4835GHz, depends on country code, maybe 2.412~2462 or 1T1R :
MCS index Data rate (Mbit/s) 20 MHz channel 40 MHz channel 800 ns 400 ns 800 ns 400 ns Baud Rate 0 1 2 3 4 5 6 7 6.5 13 19.5 26 39 52 58.5 65 7.2 14.4 21.7 28.9 43.3 57.8 13.5 27 40.5 54 81 108 65 121.5 72.2 135 15 30 45 60 90 120 135 150 IEEE 802.11g54/48/36/24/18/12/9/6(adaptive ) IEEE 802.11b11/5.5/2/1M(adaptive ) Copyright amazipoint technology Ltd. All rights are reserved. Page 3 of 13 OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 Number of Support channel 1 ~14, actual channel numbers depends on setting of country Channel Modulation Scheme Sensitivity @
PER code DBPSKDQPSKCCK and OFDM(BPSK/QPSK/16-QAM/64-QAM) 150M-68dBm@10% PER130M-68dBm@10% PER 108M -68dBm@10% PER54M-72dBm@10% PER 11M-85dBm@8% PER6M-88dBm@10% PER 1M-90dBm@8% PER Output Power 802.11b: 16 dBm 1.5dBm@11Mbps (1T1R total power) 802.11g: 14.5 dBm 1.5dBm@54Mbps 802.11n HT20: 14.5 dBm 1.5dBm @MCS7 802.11n HT40: 14.5 dBm 1.5dBm @MCS7 Antenna One IPEX I connectors for one external antenna( 1T1R) WIFI Operation Mode Client/AP System Service Virtual ServerInternal web server for browser to access Area setting Restore to default factory setting Device Management Software upgrade Reboot Change password OPENWEP SHAREDWEP WEPAUTO WPA WLAN Security Mode WPA-PSK WPA2 WPA2-PSK WPAPSKWPA2PSK WPA1WPA2(WPA and WPA2 hybrid mode) Copyright amazipoint technology Ltd. All rights are reserved. Page 4 of 13 OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 802.1x 3. Software features Support WPS Support APAccess pointClientWifi Station) mode AP mode o Default operation mode. In this mode, the module work as an Access Point, don't need any configuration. o User can use PC via RJ45 or smart phone via Wifi to login AP mode and change the default configuration ( through browser). Client mode o In this mode, module is a Wifi station. 4. Development tool :
We provide development tool for easy connection of power, RS-232, LAN, WAN, and USB port. 5. Module Dimension : 35*25 mm Copyright amazipoint technology Ltd. All rights are reserved. Page 5 of 13 OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 There are two 1.27mm pitch header on the bottom side of module P1 and P2. 6. Pin Assignment Bottom view for showing P1, P2 and pin 1/pin 2 position on bottom side of W708 module :
P1 :
Copyright amazipoint technology Ltd. All rights are reserved. Page 6 of 13 OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 Multi 1Multi 1Multi 1Multi 1 Multi 2Multi 2Multi 2Multi 2 GPIOGPIOGPIOGPIO MainMainMainMain MainMainMainMain GPIOGPIOGPIOGPIO Multi 2Multi 2Multi 2Multi 2 Multi 1Multi 1Multi 1Multi 1 GPIO23 SD_CDT GPIO25 SD_D0 GPIO24 SD_D1 GPIO22 SD_WP GPIO37 REF_CLKO GPIO39 LINK4 GPIO40 LINK3 GPIO6 GPIO7 GPIO20 URAT_TXD2 SPI_CS1 SPI_CLK 1111 3333 5555 7777 9999 11111111 13131313 15151515 17171717 19191919 2222 4444 6666 8888 10101010 12121212 14141414 16161616 18181818 20202020 SD_CMD GPIO27 GPIO28 SD_D3 GPIO29 SD_D2 SD_CLK GPIO26 POR GPIO0 SPI_MISO GPIO9 TXD0 RXD0 SPI_MOSI GPIO8 GPIO12 GPIO13 GPIO11 REFCLK P2 :
Multi 1Multi 1Multi 1Multi 1 Multi 2Multi 2Multi 2Multi 2 GPIOGPIOGPIOGPIO MainMainMainMain MainMainMainMain GPIOGPIOGPIOGPIO Multi 2Multi 2Multi 2Multi 2 Multi 1Multi 1Multi 1Multi 1 GPIO4 I2C_SCLK TXO1_P TXO1_N I2S_WS PERST_N GPIO2 GPIO36 PWM_CH1 GPIO46 RXD1 GPIO38 WDT_RST_N 3.3VD 3.3VD I2S_DO GPIO1 PWM_CH0 GPIO45 TXD1 GPIO0 I2S_DI GPIO42 LINK1 GPO44 WLAN_LED 1111 3333 5555 7777 9999 11111111 13131313 15151515 17171717 19191919 21212121 23232323 25252525 27272727 2222 4444 6666 8888 10101010 12121212 14141414 16161616 18181818 20202020 22222222 24242424 26262626 28282828 GPIO5 GPIO43 I2C_SD RXI0_P RXI0_N LINK0 GND USB_P USB_N GND TXO0_P TXO0_N RXI1_N RXI1_P I2S_CLK UART_RXD2 GPIO21 GPIO3 P1 :
1 2 3 4 Pin #
Function Direction Description SD_CDT SD_CMD SD_D0 SD_D3 In Out In/Out In/Out SDXC Card Detect SDXC Command SDXC Data0 SDXC Data3 Copyright amazipoint technology Ltd. All rights are reserved. Page 7 of 13 OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 SD_D1 SD_D2 SD_WP SD_CLK REF_CLKO POR LINK4 GPIO0 LINK3 SPI_MISO SPI_CS1 TXD0 SPI_CLK RXD0 LINK2 SPI_MOSI In/Out In/Out SDXC Data1 SDXC Data2 In Out Out In Out Out SDXC Write Protect SDXC Clock Reference clock output Power on reset input, low active Link LED for port 4 GPIO0 or WPS push button In/Out Link LED for port 3 In Out A Out A Out Out SPI MISO signal SPI chip select signal 1 Console UART TXD signal SPI clock output Console UART RXD signal Link LED for port 2 SPI MOSI signal 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 P2 :
Pin #
Function Direction Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 I2C_SCLK I2C_SD TXO1_P RXI0_P TXO1_N RXI0_N I2S_WS LINK0 PERST_N GND RXD1 In/Out In/Out I2C Clock signal I2C Data signal A A A A Tx positive for port 1 Rx positive for port 0 Tx negative for port 1 Rx negative for port 0 I2S word select Out Link LED for port 0 PCIe device reset Power ground UART1 RXD signal USB_P In/Out USB signal poistive WDT_RST_N Out Watchdog reset USB_N In/Out USB signal negative 3.3VD GND Power In 3.3V input Power ground Copyright amazipoint technology Ltd. All rights are reserved. Page 8 of 13 OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 17 18 19 20 21 22 23 24 25 26 27 28 3.3VD TXO0_P I2S_DO TXO0_N TXD1 RXI1_N I2S_DI RXI1_P LINK1 I2S_CLK WLAN_LED Power In 3.3V input A out A Out A In A Out out Out Tx positive for port 0 I2S data out Tx negative for port 0 UART1 TXD Rx negative for port 1 I2S data in Rx positive for port 1 Link LED for port 1 I2S clock signal WLAN LED output, active low UART_RXD2 In UART2 RXD 7. Memory configuration Depending on customer's request, the module can be shipped with following configuration :
Flash size : 2MB, 4MB, 8MB, 16MB, 32MB, 64MB DDR2 size : 64MB, 128MB 8. Mechanical Application Notes 1. CON0 is IPEX1 connectors on top side 2. P1 is 2*10 pins 1.27mm male header on bottom side for signals 3. P2 is 2*14 pins 1.27mm male header on bottom side for signals 4. Footprint of P1, P2 is as following :
Copyright amazipoint technology Ltd. All rights are reserved. Page 9 of 13 OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 5. There are four slot holes used for installing metal shielding cover if needed 6. There are two diameter 2.1mm holes for screw fixing 7. The mechanical drawing in .dxf format is available under request. 8. Bottom view 2D drawing is as following :
9. Shipping & package information Copyright amazipoint technology Ltd. All rights are reserved. Page 10 of 13 OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 W708 is packaged with stacked PS tray :
Tray size : for each element, the size is 45*35*12 mm, there are 8*8 elements for each tray. There are 25 trays in each carton. So, total 1600 pieces maximum for each carton.
Carton size : 500 x 400 x 300 mm
Carton Label ( packing list ) :
10. Ordering Information The part number for placing order is W708-MM-NN-G.
MM is bytes of SPI flash and NN is bytes for DDR2.
G : C for commercial grade or I for industrial grade.
For example with the standard memory configuration 8MB Flash, 64MB DDR2 and commercial grade, the part number is W708-8-64-I. Copyright amazipoint technology Ltd. All rights are reserved. Page 11 of 13 OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 11. FCC Warning Statement FEDERAL COMMUNICATIONS COMMISSION REGULATIONS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Important Note In the event that these conditions can not be example certain laptop configurations or collocation with another transmitter, then the FCC authorization is no longer considered valid the FCC ID can not be used on the final product. In these circumstances, OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text:
Contains FCC ID: 2ALWN-W708 The FCC ID can be used only when all FCC compliance requirements are met. Manual Information for End Users Copyright amazipoint technology Ltd. All rights are reserved. Page 12 of 13 OEM/Integrators Installation Manual Version:0.6 Date: 2017.5.18 The module is limited to OEM installation ONLY The module is limited to installation in mobile or fixed applications, according to Part 2.1091(b) The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations The end user must not have manual instructions to remove or install device. The user manual for end users must include the following information in a prominent location:
IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located operating in conjunction with any other antenna or transmitter. as a result of e-mail transmission. Copyright amazipoint technology Ltd. All rights are reserved. Page 13 of 13