| submitted | available | document details (if available) | source link |
|---|---|---|---|
| October 10 2016 | November 10 2016 | Acrobat Distiller 9.5.5 (Windows) |
| various | Front-End Module User Manual | Users Manual | 490.99 KiB | October 10 2016 / November 10 2016 |
PRELIMINARY DATA SHEET SKY85717-21: 5 GHz, 802.11ac Front-End Module BApplications 802.11ac set-top boxes, networking, and personal computer N E _ A P N L V I systems TX VDET RX PA LNA N E _ A N L ANT 1 C V S3512 Figure 1. SKY85717-21 Block Diagram BDescription The SKY85717-21 is a highly-integrated, 5 GHz front-end module
(FEM) incorporating a 5 GHz single-pole, double-throw (SPDT) transmit/receive (T/R) switch, a 5 GHz low-noise amplifier (LNA) with bypass, and a 5 GHz power amplifier (PA) intended for mobile/portable 802.11ac applications and systems. An enable/disable function is included that allows power savings during off mode. An integrated power detector with 20 dB of dynamic range is included to provide closed-loop power control within the system. The device is provided in a compact, 16-pin 2.5 x 2.5 x 0.4 mm Quad Flat No-Lead (QFN) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. PC cards, PCMCIA cards, mini-cards, and half mini-cards WLAN enabled wireless video systems BFeatures Integrated high performance 5 GHz PA, LNA with bypass, and SPDT Fully-matched input and output Integrated, positive slope power detector Transmit loopback mode Transmit gain: 28 dB Receive gain: 12 dB Output power: +19.5 dBm, MCS7, HT40 Output power: +18.5 dBm @ 1.8% EVM, MCS9, HT80 High linearity and high efficiency modes Direct connection to battery with 5 V nominal supply voltage Small, QFN (16-pin, 2.5 x 2.5 x 0.4 mm) package
(MSL1, 260 C per JEDEC J-STD-020) Skyworks Pb-free products are compliant with all applicable legislation. For additional information, refer to Skyworks Denition of Lead (Pb)-Free, document number SQ04-0073. N E _ A N L 16 X R C 15 D N G 14 T N A 13 GND RX GND VDD 1 2 3 4 12 GND 11 VCC2 10 VCC1 9 VLIN 5 T E D V 6 N E _ A P 7 D N G 8 X T S3513 Figure 2. SKY85717-21 Pinout 16-Pin QFN
(Top View) Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com 203068E Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice August 18, 2014 1 4 0 1 PRELIMINARY DATA SHEET SKY85717-21: FRONT-END MODULE BTechnical Description The SKY85717-21 is comprised of a high performance 5 GHz PA, 5 GHz LNA, and broadband SPDT switch. The device is fully-
matched, and requires few external components for optimal performance, which makes it ideal for small portable/mobile applications. The FEM provides up to +28 dB of gain over the frequency band. The LNA supports an enable/disable mode for power savings when not in receive mode and a bypass function for increased receive dynamic range. The PA can be shut off using the PA_EN signal (pin 6). BElectrical and Mechanical Specifications Signal pin assignments and functional pin descriptions are described in Table 1. The absolute maximum ratings of the SKY85717-21 are provided in Table 2. The recommended operating conditions are specified in Table 3 and electrical specifications are provided in Tables 4, 5, and 6. The state of the SKY85717-21 is determined by the logic provided in Table 7. Table 1. SKY85717-21 Signal Descriptions Pin Name Description 1 2 3 4 5 6 7 8 GND RX GND VDD VDET PA_EN GND TX Ground RF receive output Ground LNA supply voltage and transmit bias Detector output voltage PA enable Ground RF transmit input Note: N/C = No connect. Keep pin floating. BPackage and Handling Information Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY85717-21 is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Pin 9 10 11 12 13 14 15 16 Name Description Transmit linearity mode control Supply voltage Supply voltage Ground Antenna Ground Switch control voltage VLIN VCC1 VCC2 GND ANT GND CRX LNA_EN LNA enable 2 Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com August 18, 2014 Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice 203068E 5 2 6 PRELIMINARY DATA SHEET SKY85717-21: FRONT-END MODULE Table 2. SKY85717-21 Absolute Maximum Ratings (Note 1) Parameter Symbol Minimum Maximum Supply voltage (non-operating, no RF) DC input on control pin (PA_EN, LNA_EN, CRX, VLIN) Input power (ANT terminated in 50 match) Case operating temperature Storage temperature Electrostatic discharge:
Human Body Model (HBM), Class 1C VCC VDD VIN PIN TA TST ESD 1 1 0.3 40 40
+6
+6
+6.0
+5
+85
+140 1000 Units V V V dBm C C V Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. SKY85717-21 Recommended Operating Conditions Parameter Symbol Minimum Supply voltage relative to GND = 0 V Operating temperature VCC, VDD TA 3.9 40 Typical 5.0
+25 Maximum 5.5
+85 Units V C Table 4. SKY85717-21 Electrical Specifications: DC Characteristics (Note 1)
(VCC = 5.0 V, PA_EN = 3.3 V, TA = 25 C, All Unused Ports Terminated with 50 , Unless Otherwise Noted) Typical Test Condition Parameter Symbol Min Supply current, high linearity mode Supply current, high efficiency mode Supply current ICC-A ICC-A ICC-OFF POUT = +20.5 dBm, VLIN = 3.3 V POUT = +20.5 dBm, VLIN = 0 V No RF applied, PA_EN = CRX =
LNA_EN = 0 V Quiescent current, high efficiency mode ICQ No RF LNA supply current ICC_LNA LNA_EN = 3.3 V, CRX = 3.3 V LNA bypass supply current ICC_LNA_BYP LNA_EN = 0 V, CRX = 3.3 V TNote 1: Performance is guaranteed only under the conditions listed in this table. 230 220 20 170 11 200 Max 260 240 Units mA mA A mA mA A Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com 203068E Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice August 18, 2014 3 PRELIMINARY DATA SHEET SKY85717-21: FRONT-END MODULE Table 5. SKY85717-21 Electrical Specifications: General (Note 1)
(VCC = 5.0 V, PA_EN = 3.3 V, LNA_EN = CRX = 0 V, TA = 25 C, All Unused Ports Terminated with 50 , Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Transmit Characteristics Frequency range Error Vector Magnitude, high linearity mode f EVM 5150 to 5850 MHz, VLIN = 3.3 V:
POUT = +19.5 dBm, MCS7, HT40 POUT = +18.5 dBm, MCS9, HT80 Error Vector Magnitude, high efficiency mode EVM 5150 to 5850 MHz, VLIN = 0 V:
POUT = +19.5 dBm, MCS7, HT40 POUT = +18.5 dBm, MCS9, HT80 4900 MCS0, mask compliance
+22 Output power Small signal gain Harmonics (2nd and 3rd) Delay and rise/fall time Input return loss Stability Ruggedness Receive Characteristics Frequency range Small signal gain Noise figure 3P rd P Order Input Intercept Point Input return loss Output return loss Enable time Power Detector Characteristics Frequency range Power detector range, CW Output impedance Output voltage Detector bandwidth POUT S21 2fo, 3fo tDR, tDF S11 Stab f S21 NF IIP3 S11 S22 tEN f PDR 5150 to 5850 MHz POUT = +20 dBm, 6 Mbps, 802.11a 50% of VPA_EN edge and 90/10% of final output power level
@ TX port 802.11n, MCS0, HT40, POUT =
+20 dBm, 0.1 GHz to 20 GHz, load VSWR = 6:1 CW, PIN = 0 dBm, 0.1 GHz to 20 GHz, load VSWR = 10:1 LNA enabled Bypass mode LNA enabled Bypass mode LNA enabled Bypass mode 10% to 90% of receive RF power, from time that LNA_EN is at 50%
Measured @ ANT pin PDZLOAD PDVNO_RF PDVP21 PDBW POUT = no RF, measured into 1 M POUT = +21 dBm, CW, measured into 1 M 1.8 1.8
+24 28 12 5850 MHz 3.0 2.0 3.0 2.0 45 400
%
%
%
%
dBm dB dBm/MHz ns dB All non-harmonically related outputs < 43 dBm/MHz No permanent damage or performance degradation 4900 4900 0
+12 8 2.5
+5
+20 8 8 8 2.2 0.2 0.9 3.6 5850 400 5850
+23 MHz dB dB dB dBm dBm dB dB dB ns MHz dBm k V V MHz TNote 1: Performance is guaranteed only under the conditions listed in this table. 4 Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com August 18, 2014 Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice 203068E PRELIMINARY DATA SHEET SKY85717-21: FRONT-END MODULE Table 6. SKY85717-21 Electrical Specifications: Control Logic Characteristics (Note 1)
(VCC = 5.0 V, PA_EN = 3.3 V, LNA_EN = CRX = 0 V, TA = 25 C, All Unused Ports Terminated with 50 , Unless Otherwise Noted) Parameter Symbol Test Condition Control voltage:
High Low Input current, high Input current, low VIH VIL IIH IIL TNote 1: Performance is guaranteed only under the conditions listed in this table. Table 7. SKY85717-21 Control Logic Min 1.6 0 Typical 120 Max 3.6 0.4 1 Units V V A A Mode CRX (Pin 15) LNA_EN (Pin 16)
(Note 1) PA_EN (Pin 6)
(Note 2) VLIN (Pin 9) WLAN receive WLAN receive bypass mode WLAN transmit, high linearity mode WLAN transmit, high efficiency mode WLAN off 1 1 0 0 0 Note 1: LNA is on while LNA_EN is high. LNA is off and in bypass mode when LNA_EN is low. Note 2: PA_EN controls PA enable and transmit/receive switch logic. 1 0 0 0 0 0 0 1 1 0 0 0 1 0 0 Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com 203068E Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice August 18, 2014 5 PRELIMINARY DATA SHEET SKY85717-21: FRONT-END MODULE Evaluation Board Description The SKY85717-21 Evaluation Board is used to test the performance of the SKY85717-21 FEM. A suggested application schematic diagram is shown in Figure 3. A photograph of the Evaluation Board is shown in Figure 4. A Bill of Materials (BOM) for the Evaluation Board is provided in Table 8. Evaluation Board Test Procedures 1. Connect the system ground to connector J4, pin 2, of the Evaluation Board. 2. Apply 5 V to connector J4, pins 1 and 3. 3. Select a path to test according to the modes shown in Table 7. 4. Connect a multimeter or oscilloscope to connector J5, pin 12, to monitor the power detector voltage. 5. Apply an RF signal to connector J1 (ANT) to monitor the RX to ANT performance. Measure the response from the output of connector J2 (RX). 6. Apply an RF signal to connector J3 (TX) to monitor the ANT to TX performance. Monitor the output power on connector J1
(ANT). Care should be taken not to overdrive the amplifier by applying too much RF on the input to the device (20 dBm provides a suitable starting input power for the device). BCircuit Design Considerations The following design considerations are general in nature and must be followed regardless of final use or configuration:
Paths to ground should be made as short as possible. The RX and ANT ports are AC-coupled and do not require DC blocking capacitors. There are ESD diodes to ground and a DC blocking capacitor between the TX port (pin 8) and the die. Therefore, there is no DC present on this port. If the TX port is connected to an external component with
>3 VDC present on it, a 10 pF (component C8) general purpose blocking capacitor is recommended. Capacitors C6 (1 F) and C7 (100 pF) should be on the primary side of the Evaluation Board at a minimum manufacturable distance from the FEM. Capacitor C20 (0.3 pF) needs to be as close as possible at manufacturable distance from the ANT pin of the IC, followed by L1 (1.0 nH) and C19 (0.3 pF), also at manufacturable distance from C20 and L1, respectively. The ground pad of the SKY85717-21 has special electrical and thermal grounding requirements. This pad is the main thermal conduit for heat dissipation. Because the circuit board acts as the heat sink, it must shunt as much heat as possible from the device. Therefore, design the connection to the ground pad to dissipate the maximum wattage produced by the circuit board. Multiple vias to the grounding layer are required. Evaluation Board trace losses are:
RX = TX = 0.32 dB and ANT = 0.35 dB. NOTE: A poor connection between the ground pad and the ground increases the junction temperature (TJ), which reduces the life of the device. Package Dimensions The PCB layout footprint for the SKY85717-21 is shown in Figure 5. Typical part markings are shown in Figure 6. Package dimensions for the 16-pin QFN are shown in Figure 7, and tape and reel dimensions are provided in Figure 8. 6 Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com August 18, 2014 Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice 203068E 9 PRELIMINARY DATA SHEET SKY85717-21: FRONT-END MODULE SMA J1 C19 0.3 pF C20 0.3 pF L1 1.0 nH 17 16 15 14 13 D A P 1 2 3 4 GND RX GND VDD X R C D N G T N A N E _ A N L N E _ A P T E D V D N G X T 5 6 7 8 12 11 10 9 GND VCC2 VCC1 VLIN CRX LEN VDD J2 SMA VDET PEN R4 26.1 K J3 SMA C8 0 R7 0 R8 25 C7 100 pF C4 1 F C6 1 F C3 1 F J4 2 4 6 8 VCC2 VCC1 1 3 5 7 1 TP1 VDD 1 4 7 10 LEN CRX TP2 VDD J5 J5 J5 2 5 8 11 3 6 9 12 PEN VDET Y0585 Figure 3. SKY85717-21 Application Schematic Figure 4. SKY85717-21 Evaluation Board Assembly Y0461 Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com 203068E Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice August 18, 2014 7 PRELIMINARY DATA SHEET SKY85717-21: FRONT-END MODULE Table 8. SKY85717-21 Evaluation Board Bill of Materials (BOM) Reference Value Manufacturer Mfr Part Number Package Description R7 L1 R8 R4 C7 C19, C20 C8, R3 C3, C4, C6 0 1.0 nH 24.9 26.1K 100 pF 0.3 pF 0 1 uF Panasonic Murata Panasonic Panasonic Murata Murata Panasonic ERJ2GEJ0R0 LQG15HN1N0S02D ERJ2RKF24R9 ERJ2RKF2612 GRM1555C1H101JZ01 GJM1555C1HR30WB01 ERJ2GE0R00 TDK Corporation C1005X5R1A105K 0402 0402 0402 0402 0402 0402 0402 0402 Thick film chip resistor High frequency multilayer Thick film chip resistor Thick film chip resistor Multilayer ceramic RF, High Q, low loss Thick film chip resistor Multilayer ceramic 8 Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com August 18, 2014 Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice 203068E PRELIMINARY DATA SHEET SKY85717-21: FRONT-END MODULE 2.90 1.35 16 15 14 13 0 4
. 0 X 2 0 0 4
. 0 X 2 14 2.90 1 2 3 4 12 11 10 9 1.35 0.475 Typ. 2X 0.40 0 3 2X 0.40 12 0 5 6 7 8 0.500 Typ. 0.20 Typ. Board Metal 3.00 1.25 16 15 14 13 3.00 1 2 3 4 8X C0.050 X 45 12 11 10 9 1 2 3 4 1.25 2.90 0.575 Typ. 0 5X 0.250 Via Pattern
(Note 4) 2.90 0.20 Typ. 16 15 14 0.45 Typ. 13 52% solder coverage on center pad 12 11 10 9 0.20 Typ. 0.45 Typ. 0.475 Typ. Package Outline 0.500 Typ. 5 6 7 8 0.30 Typ. 0.500 Typ. 0.20 Typ. 5 6 7 8 Solder Mask Pattern
(Note 6) Notes:
Stencil Pattern
(Note 5) 1. All dimensions are in millimeters 2. Dimensioning and tolerancing according to ASME Y14.5M-1994 3. Unless specied, dimensions are symmetrical about center lines. 4. Via hole recommendations: 0.025 mm Cu via wall plating (minimum), 5. Stencil recommendations: 0.10 mm stencil thickness, laser cut apertures, trapezoidal walls and rounded corners offer better paste release. 6. Solder mask recommendations: contact board fabricator for recommended soldermask on the far side should tent or plug via holes. solder mask offset and tolerance. S2655 Figure 5. SKY85717-21 PCB Layout Footprint Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com 203068E Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice August 18, 2014 9 PRELIMINARY DATA SHEET SKY85717-21: FRONT-END MODULE Pin1 Indicator SKY21 85717 XXXXX Figure 6. Typical Part Markings
(Top View) Skyworks Part Number Lot Number 0 6 4 0 Y 2.50 A B 0.05 C Pin 1 Indicator 0.40 Max 0.127 Ref 0.02 + 0.03 0.02 16X 0.30 Min 1.35 0.05 4X 0.15, Internal Support Only. Do Not Solder or Route Under Pin 1 Indicator O.30 x 45 Exposed Pad 2.50 1.35 0.05 2X 0.05 C 2X 0.05 C Top View Notes:
8X 0.15 21X 0.05 C C 4 g n i t a e S e n a P l Side View Angular Tolerance:
0.5 1. All measurements are in millimeters. 2. Dimensions and tolerances according to ASME Y14.5M-1994. 3. Unless otherwise specied the following values apply:
Decimal Tolerance:
X.X (1 place) 0.1 mm 4. Coplanarity applies to the terminals as well as all other bottom 5. Dimension applies to metallized terminal. If terminal tip has a radius, dimension should not be measured in that radius area. 6. Unless specied, dimensions are symmetrical about center lines. X.XX (2 places) 0.05 mm X.XXX (3 places) 0.025 mm surface metallization. R0.075, Typ 0.500 8X 0.12 Min See Detail A Bottom View 2X 0.075 Detail A Scale 2X 16 Places 0.10 M C A B 0.225 0.05 0.20 0.05 5 Y1253 Figure 7. SKY85717-21 16-Pin QFN Package Dimensions 10 August 18, 2014 Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice 203068E Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com PRELIMINARY DATA SHEET SKY85717-21: FRONT-END MODULE 2.00 0.05)
(See Note 1) 1.55 0.05 4.00 0.1
(See Note 2) 1.75 0.1 0.25 0.05 1.00 Min. 5 0 0 5 7 2
. C L 0.70 0.10 A A A R0.1 Typ. 4.00 0.10 2.75 0.05 Notes:
1. Measured from centerline of sprocket hole to centerline of pocket. 2. Cumulative tolerance of 10 sprocket holes: 0.02 mm. 3. All measurements are in millimeters. Figure 8. SKY85717-21 Tape and Reel Dimensions
. 0 1 0 0 5 3
) 1 e t o N e e S
.
(
. 0 1 0
/
0 3 0
+
0 0 8
. Pin 1 Indicator S2678a 203068E Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice August 18, 2014 11 Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com PRELIMINARY DATA SHEET SKY85717-21: FRONT-END MODULE BOrdering Information Model Name Manufacturing Part Number Evaluation Board Part Number SKY85717-21: 5 GHz, 802.11ac Front-End Module SKY85717-21 SKY85717-21-EVB Copyright 2014 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (Skyworks) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. 12 August 18, 2014 Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice 203068E Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com 8
This product uses the FCC Data API but is not endorsed or certified by the FCC