all | frequencies |
|
|
|
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
USER MANUAL 1 OF 7 | Users Manual | 2.74 MiB | ||||
1 |
|
USER MANUAL 2 OF 7 | Users Manual | 2.79 MiB | ||||
1 |
|
USER MANUAL 3 OF 7 | Users Manual | 2.40 MiB | ||||
1 |
|
USER MANUAL 4 OF 7 | Users Manual | 2.88 MiB | ||||
1 |
|
USER MANUAL 5 OF 7 | Users Manual | 2.89 MiB | ||||
1 |
|
USER MANUAL 6 OF 7 | Users Manual | 2.60 MiB | ||||
1 |
|
USER MANUAL 7 OF 7 | Users Manual | 915.25 KiB | ||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | ID Label/Location Info | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | USER MANUAL 1 OF 7 | Users Manual | 2.74 MiB |
Wireless G Travel Router Share your hotel broadband Internet connection User Manual F5D7233 Table of Contents 1. Introduction . 1 Advantages of a Wireless Network . 1 Placement of your Router for Optimal Performance. 2 2. Product Overview . 6 Product Features . 6 3. Knowing your Router . 9 Package Contents . 9 System Requirements . 9 Product Diagrams . 10 4. Connecting and Configuring your Router . 12 Router Mode Installation . 13 Adapter Mode Installation . 16 Access Point Mode Installation . 18 5. Using the Web-Based Advanced User Interface . 20 Logging into the Router . 20 Logging out of the Router . 21 Setting your Connection Type . 24 Setting Custom Domain Name Server (DNS) Settings . 30 Configuring your WAN Media Access Controller (MAC) Address . 30 Viewing LAN Settings. 32 Changing LAN Settings . 33 Viewing the DHCP Client List Page . 35 Configuring the Wireless Network Settings . 36 Securing your Wi-Fi Network . 37 WEP Setup. 42 Changing the Wireless Security Settings . 44 WPA Setup . 44 WPA/WPA2 Setup . 45 Utilities Tab . 52 Restarting the Router . 53 Updating the Firmware . 58 6. Manually Configuring Network Settings . 62 7. Recommended Web Browser Settings . 64 8. Using the Access Point Mode . 66 9. Using the Adapter Mode . 67 10. Troubleshooting . 73 11. Information . 80 3 Introduction Thank you for purchasing the Belkin Wireless G Travel Router (the Router). Please be sure to read through this User Manual completely, and pay special attention to the section entitled Placement of your Router for Optimal Performance on page 2. Advantages of a Wireless Network Mobility you no longer need a dedicated computer roomnow you can work on a networked laptop or desktop computer anywhere within your wireless range Easy installation The Belkin Easy Installation Wizard makes setup simple Flexibility set up and access printers, computers, and other networking devices from anywhere in your home Easy expansion the wide range of Belkin networking products let you expand your network to include devices such as printers and gaming consoles No cabling required you can spare the expense and hassle of retrofitting Ethernet cabling throughout the home or office Widespread industry acceptance choose from a wide range of interoperable networking products s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 1 Introduction Introduction Placement of your Router for Optimal Performance Important Factors for Placement and Setup Your wireless connection will be stronger the closer your computer is to your Router. Typical indoor operating range for wireless devices is between 100 and 200 feet. In the same way, your wireless connection and performance will degrade somewhat as the distance between your Router and connected devices increases. This may or may not be noticeable to you. As you move farther from your Router, connection speed may decrease. Factors that can weaken signals simply by getting in the way of your networks radio waves are metal appliances or obstructions, and walls. If you have concerns about your networks performance that might be related to range or obstruction factors, try moving the computer to a position between five and 10 feet away from the Router in order to see if distance is the problem. If difficulties persist even at close range, please contact Belkin Technical Support. Note: While some of the items listed below can affect network performance, they will not prohibit your wireless network from functioning; if you are concerned that your network is not operating at its maximum effectiveness, this checklist may help. 1. Wireless Router Placement Place your Router, the central connection point of your network, as close as possible to the center of your wireless network devices. To achieve the best wireless network coverage for your wireless clients (i.e., computers enabled by Belkin Wireless Notebook Network Cards, Wireless Desktop Network Cards, and Wireless USB Adapters):
Ensure that your Routers networking antennas are parallel to each other, and are positioned vertically (toward the ceiling). If your Router itself is positioned vertically, point the antennas as much as possible in an upward direction. In multistory homes, place the Router on a floor that is as close to the center of the home as possible. This may mean placing the Router on an upper floor. Try not to place the Router near a cordless phone. 2 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Introduction 2. Avoid Obstacles and Interference Avoid placing your Router near devices that may emit radio noise, such as microwave ovens. Dense objects that can inhibit wireless communication include:
Refrigerators Washers and/or dryers Metal cabinets Large aquariums Metallic-based, UV-tinted windows If your wireless signal seems weak in some spots, make sure that objects such as these are not blocking the signals path (between your computers and Router). 3. Cordless Phones If the performance of your wireless network is impaired after attending to the above issues, and you have a cordless phone:
Try moving cordless phones away from the Router and your wireless-enabled computers. Unplug and remove the battery from any cordless phone that operates on the 2.4GHz band (check the manufacturers information). If this fixes the problem, your phone may be interfering. If your phone supports channel selection, change the channel on the phone to the farthest channel from your wireless network. For example, change the phone to channel 1 and move your Router to channel 11. See your phones user manual for detailed instructions. If necessary, consider switching to a 900MHz cordless phone. 4. Choose the Quietest Channel for your Wireless Network In locations where homes or offices are close together, such as apartment buildings or office complexes, there may be wireless networks nearby that can conflict with yours. Use the Site Survey capabilities found in the wireless utility of your wireless adapter or card to locate any other wireless networks that are available (see your wireless adapters or cards user manual), and move your Router and computers to a channel as far away from other networks as possible. 3 Introduction Introduction Experiment with more than one of the available channels in order to find the clearest connection and avoid interference from neighboring cordless phones or other wireless devices. For Belkin wireless networking products, use the detailed Site Survey and wireless channel information included with your Wireless Network Card. See your Network Cards user guide for more information. These guidelines should allow you to cover the maximum possible area with your Router. Should you need to cover an even wider area, we suggest the Belkin Wireless G Range Extender/Access Point. 5. Secure Connections, VPNs, and AOL Secure connections typically require a user name and password, and are used where security is important. Secure connections include:
Virtual Private Network (VPN) connections, often used to connect remotely to an office network The Bring Your Own Access program from America Online
(AOL), which lets you use AOL through broadband provided by another cable or DSL service Most online banking websites Many commercial websites that require a user name and password to access your account Secure connections can be interrupted by a computers power management setting, which causes it to go to sleep. The easiest solution to avoid this is to simply reconnect by rerunning the VPN or AOL software, or by re-logging into the secure website. A second alternative is to change your computers power management settings so it does not go to sleep; however, this may not be appropriate for portable computers. To change your power management setting under Windows, see the Power Options item in the Control Panel. If you continue to have difficulty with secure connections, VPNs, and AOL, please review the steps above to be sure you have addressed these issues. 4 Introduction For more information regarding our networking products, visit our website at www.belkin.com/networking or call Belkin Technical Support at:
US:
Europe:
Australia:
New Zealand:
Singapore:
877-736-5771 310-898-1100 ext. 2263 00 800 223 55 460 1800 235 546 0800 235 546 800 616 1790 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 5 Product Overview Product Features In minutes you will be able to share your Internet connection and network your computers. The following is a list of features that make your new Belkin Wireless G Travel Router an ideal solution for your home or small office network. Works with PC Computers The Router supports a variety of networking environments, including Windows 98, Me, 2000, and XP. All you need is an Internet browser and a network adapter that supports TCP/IP (the standard language of the Internet). Front-Panel LED Display Lighted LEDs on the front of the Router indicate which functions are in operation. Youll know at-a-glance whether your Router is connected to the Internet. This feature eliminates the need for advanced software and status-monitoring procedures. Web-Based Advanced User Interface You can set up the Routers advanced functions easily through your web browser, without having to install additional software onto the computer. There are no disks to install or keep track of and, best of all, you can make changes and perform setup functions from any computer on the network quickly and easily. NAT IP Address Sharing Your Router employs Network Address Translation (NAT) to share the single IP address assigned to you by your Internet Service Provider while saving the cost of adding IP addresses to your Internet service account. SPI Firewall Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks, including IP Spoofing, Land Attack, Ping of Death (PoD), Denial of Service (DoS), IP with zero length, Smurf Attack, TCP Null Scan, SYN flood, UDP flooding, Tear Drop Attack, ICMP defect, RIP defect, and fragment flooding. 6 Product Overview Integrated 10/100 4-Port Switch The Router has a built-in, 4-port network switch to allow your wired computers to share printers, data and MP3 files, digital photos, and much more. The switch features automatic detection so it will adjust to the speed of connected devices. The switch will transfer data between computers and the Internet simultaneously without interrupting or consuming resources. Universal Plug-and-Play (UPnP) Compatibility UPnP (Universal Plug-and-Play) is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnP-compliant. Support for VPN Pass-Through If you connect to your office network from home using a VPN connection, your Router will allow your VPN-equipped computer to pass through the Router and to your office network. Built-In Dynamic Host Configuration Protocol (DHCP) Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes for the easiest possible connection of a network. The DHCP server will assign IP addresses to each computer automatically so there is no need for a complicated networking setup. Easy Install Wizard The Easy Install Wizard takes the guesswork out of setting up your Router. This automatic software determines your network settings for you and sets up the Router for connection to your Internet Service Provider (ISP). In a matter of minutes, your Wireless Router will be up and running on the Internet. NOTE: Easy Install Wizard software is compatible with Windows 98SE, Me, 2000, and XP. s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 7 Product Overview MAC Address Filtering For added security, you can set up a list of MAC addresses (unique client identifiers) that are allowed access to your network. Every computer has its own MAC address. Simply enter these MAC addresses into a list using the Web-Based Advanced User Interface and you can control access to your network. 8 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Knowing your Router Package Contents Wireless G Travel Router Quick Installation Guide Installation Software CD Power Supply USB Power Cable Ethernet Cable System Requirements Windows 98, Me, 2000, or XP PC-compatible laptop 9 Knowing your Router Knowing your Router Product Diagrams
(C)
(B)
(A) Top A. Wireless LED B. Ethernet LED C. Power LED
(C)
(B)
(A) Rear Panel A. Power Cable Port B. Ethernet Cable Port C. Mode Switch 10 Knowing your Router
(A)(A) Bottom A. Reset Button s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 11 Connecting and Configuring your Router The Belkin Wireless G Travel Router is a 3-in-1 solution providing the busy traveler the versatility to meet his or her connection needs. The three installation modes are:
Installation Modes Router Mode create a wireless network in a hotel, home, or office Adapter Mode connect your PC wirelessly to a router or hotspot Access Point Mode expand the coverage of an existing network 12 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Connecting and Configuring your Router Router Mode Installation 1. Install Run the Easy Install Wizard first!
1. Install Run the Easy Install Wizard first!
DO NOT CONNECT THE ROUTER AT THIS TIME. Important for Hotel Users:
Do not connect to the hotels high-speed Internet connection at this time (to avoid being charged more than once). 1.1 Insert the Installation CD into your CD-ROM drive. You will see the Wizards welcome screen. Click Run the Easy Install Wizard. 1.2 The Easy Install Wizard will ask you to select which mode you want the Router to use. Select Router Mode, and click Next. 1.3 The next screen will show you how to select the mode on the Routers back panel. Move the center of the button on the back panel to align with the word Router. Then, click Next. 13 Connecting and Configuring your Router Connecting and Configuring your Router 2. Connect Connecting the Routers Cables
. Connect Connecting the Routers Cables 2.1 Connect one end of the included Ethernet cable into the Router and the other end into a hotels Internet connection or a cable/DSL modem. Next, plug the included power supply into the Router, and then click Next. 2.2 From your PC, wirelessly connect to the Router using your PCs built-in wireless card or external wireless adapter. The network name (SSID) of the Router is Belkin Traveler. Once you have connected wirelessly, click Next. 2.3 Select one of the following:
Hotel Connection Select Hotel Connection if you are in a hotel. CLICK NEXT AND FOLLOW THE INSTRUCTIONS IN STEP 3. Cable/DSL Connection If you are using a cable/DSL modem, select All Other Connections. CLICK NEXT AND FOLLOW THE INSTRUCTIONS IN STEP 4. 14 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Connecting and Configuring your Router 3. Configure Hotel Users - Configuration for Hotel Connections
. Configure Hotel Users - Configuration for Hotel Connections 3.1 Click the Hotel Home Page button to open up a web browser and set up the hotels connection. You may be required to accept the terms of the hotels high-speed Internet connection in order to access the Internet. 3.2 Your installation is now complete. However, if you would like to set up any advanced features
(such as security features), you may click the Advanced Features button or type 192.168.2.1 into the navigation bar of your web browser. Click Finish. 4. Configure Cable/DSL Users - Configuration for Cable/DSL Connections
. Configure 4.1 Select one of the following Internet connection options under Cable or DSL modem. Select your Internet connection and click Continue. Note: If you do not see the page pictured here, open a web browser. Once you have established a connection with the Router, type 192.168.2.1 into the navigation bar of your web browser. 4.2 Your installation is now complete. However, if you would like to set up any advanced features (such as security features), you may click the Advanced Features button or type 192.168.2.1 into the navigation bar of your web browser. Click Finish. 15
1 | USER MANUAL 2 OF 7 | Users Manual | 2.79 MiB |
Connecting and Configuring your Router Connecting and Configuring your Router Adapter Mode Installation 1. Mode Selecting Adapter Mode 1. Mode Selecting Adapter Mode 1.1 Select Adapter Mode, then click Next. 1.2 Move the center of the switch on the back panel to align with the word Adapter. Click Next. 2. Connect Connecting the Cables
. Connect 2.1 Connect one end of the included Ethernet cable to the Router (which is now functioning in Adapter Mode) and the other end into your PCs RJ45 port. Next, plug the included USB power cable into the Router with the USB end in the PCs USB port, or plug the included power supply into the Router and then into a wall outlet. Click Next. 16 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Connecting and Configuring your Router 2.2 Check to make sure that the Ethernet and Power LEDs on the front of the Router are on. Click Next to go to the Routers home page on the Web. 3. Configure Configuration for Adapter Mode
. Configure 3.1 Wirelessly connect to a network from the Available Networks window. Select a network by clicking Join and then Connect. The status window will tell you the current status of the network to which the Router is currently connected. Click Next. Note: If you do not see the page pictured here once you have established a connection with the Router, p lease refer to the Using Router, p Router the Adapter Mode section in this manual on page 67. 3.2 Your installation is now complete. However, if you would like to set up any advanced features (such as security features), you may click the Advanced Features button or type 192.168.2.225 into the navigation bar of your web browser. 17 Connecting and Configuring your Router Connecting and Configuring your Router Access Point Mode Installation 1. Mode Selecting the Access Point Mode 1. Mode Selecting the Access Point Mode 1.1 Select Access Point Mode. Click Next. 1.2 Move the center of the switch on the back panel to align with the word AP. Click Next. 2. Connect Connecting the Cables
. Connect 2.1 Connect one end of the included Ethernet cable to the Router (which is now functioning in Access Point Mode) and the other end to a cable/DSL modem. Next, plug the included power supply into the Router and click Next. 18 Connecting and Configuring your Router 2.2 From your PC, wirelessly connect to the Router using your PCs built-in wireless card or external wireless adapter. The network name (SSID) of the Router is Belkin Traveler. Once you have wirelessly connected, click Next. 3. Configure Configuration for Access Point Mode
. Configure 3.1 Once you have established a connection with the Router, your installation is complete. However, if you would like to set up any advanced features (such as security features), you may click the Advanced Features button or type 192.168.2.254 into the navigation bar of your web browser. s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 19 Using the Web-Based Advanced User Interface The Web-Based Advanced User Interface is a web-based tool that you can use to set up the Router if you dont want to use the Easy Install Wizard. You can also use it to manage advanced Router functions. From the Web-Based Advanced User Interface window, you can perform the following tasks:
Configure the Router to connect to your ISP with the settings that View the Routers current settings and status they provided you Change current network settings such as the internal IP address, the IP address pool, DHCP settings, and more Set the Routers firewall to work with specific applications via port forwarding Set up security features such as client restrictions, MAC address filtering, WEP, and WPA Enable the DMZ feature for a single computer on your network Enable/disable UPnP (Universal Plug-and-Play) Reset the Router Back up your configuration settings Reset the Routers default settings Change the Routers internal password Update the Routers firmware You can access the Routers Web-Based Advanced User Interface using your Internet browser. In the navigation bar of your browser, type 192.168.2.1 (you do not need to type in http:// or www). Press the Enter key. PLEASE NOTE: If you have difficulty accessing the Routers Web-Based Advanced User Interface, go to the section of this User Manual entitled Manually Configuring Network Settings. Logging into the Router You will see the Routers home page in your browser window. The home page is visible to any user who wants to see it. To make any changes to the Routers settings, you have to log in. Clicking the Login button or clicking on any one of the links on the home page 20 Using the Web-Based Advanced User Interface will take you to the login screen. The Router ships with no password. In the login screen, leave the password field blank and click Submit to log in. Logging out of the Router One computer at a time can log into the Router to make changes to Router settings. Once a user has logged in to make changes, there are two ways that the computer can be logged out. The first is to click the Logout button. The second method is automatic. The login will time out after a specified period of time. The default login time-out is 10 minutes. This can be changed to any period of time from 1 to 99 minutes. For more information, see the section in this manual entitled Login Time-Out. s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 21 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface The home page is the first page you will see when you access the Web-Based Advanced User Interface (UI). The home page provides a quick view of the Routers status and settings. All advanced setup pages can be reached from this page.
(10)
(2)
(5)
(4)
(3)
(6)
(1)
(8)
(7)
(9) 1. Quick-Navigation Links You can go directly to any of the Routers UI pages by clicking directly on these links. The links are divided into logical categories and grouped by tabs to make finding a particular setting easier to find. Clicking on the purple header of each tab will show you a short description of the tabs function. 2. Home Button 3. The Home button is available in every page of the UI. Pressing this button will take you back to the home page. Internet Status Indicator This indicator is visible in all pages of the UI, indicating the connection status of the Router. When the indicator says connection OK in GREEN, the Router is connected to the Internet. When the Router is not connected to the Internet, the indicator will read no connection in RED. The indicator is automatically updated when you make changes to the settings of the Router. 22 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Using the Web-Based Advanced User Interface 4. Login/Logout Button This button enables you to log in and out of the Router with the press of one button. When you are logged into the Router, this button will change to read Logout. Logging into the Router will take you to a separate login page where you will need to enter a password. When you are logged into the Router, you can make changes to the settings. When you are finished making changes, you can log out of the Router by clicking the Logout button. For more information about logging into the Router, see the section called Logging into the Router. 5. Help Button The Help button gives you access to the Routers help pages. Help is also available on many pages by clicking more info next to certain sections of each page. 6. LAN Settings Shows you the settings of the Local Area Network (LAN) side of the Router. Changes can be made to the settings by clicking on any one of the links (IP Address, Subnet Mask, DHCP Server) or by clicking the LAN Quick Navigation link on the left side of the screen. 7. Features 8. Shows the status of the Routers NAT, firewall, and wireless features. Changes can be made to the settings by clicking on any one of the links or by clicking the Quick Navigation links on the left side of the screen. Internet Settings Shows the settings of the Internet/WAN side of the Router that connects to the Internet. Changes to any of these settings can be made by clicking on the links or by clicking on the Internet/WAN Quick Navigation link on the left side of the screen. 9. Version Info Shows the firmware version, boot-code version, hardware version, and serial number of the Router. 10. Page Name The page you are on can be identified by this name. This User Manual will sometimes refer to pages by name. For instance LAN > LAN Settings refers to the LAN Settings page. 23 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Setting your Connection Type Setting your Internet Service Provider (ISP) Connection Type to Dynamic IP A dynamic connection is the most common connection type used with cable modems. Setting the connection type to dynamic in many cases is enough to complete the connection to your ISP. Some dynamic connections may require a host name. If your ISP assigned you a host name, you can enter it in the space provided. Some dynamic connections may require that you clone the MAC address of the PC that was originally connected to the modem.
(1)
(2) 1. Host Name If a host name must be visible to your ISP, enter the host name your ISP has provided here. Click Apply Changes (3). If your ISP did not assign you a host name, or you are uncertain about whether your ISP requires a visible host name, leave this field blank. 2. Change WAN MAC Address If your ISP requires a specific MAC address to connect to the service, you can enter a specific MAC address or clone the current computers MAC address through this link. 24 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Using the Web-Based Advanced User Interface
(2)
(3) Setting your Internet Service Provider (ISP) Connection Type to Static IP A static IP connection is less common than other connection types. If your ISP uses static IP addressing, you will need your IP address, subnet mask, and ISP gateway address. This information is available from your ISP. Type in your information, then click Apply Changes (4). After you apply the changes, if your Router is set up properly, the Internet Status indicator will read Connected.
(1)
(2)
(3)
(4) 1. IP Address Provided by your ISP. Enter your IP address here. 2. Subnet Mask 3. Provided by your ISP. Enter your subnet mask here. ISP Gateway Address Provided by your ISP. Enter the ISP gateway address here. 25
1 | USER MANUAL 3 OF 7 | Users Manual | 2.40 MiB |
Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Setting your ISP Connection Type to PPPoE Most DSL providers use PPPoE as the connection type. If you use a DSL modem to connect to the Internet, your ISP may use PPPoE to log you into the service. If you have an Internet connection in your home or small office that doesnt require a modem, you may also use PPPoE.
(1)
(2)
(3)
(4)
(5) Your connection type is PPPoE if:
1) Your ISP gave you a user name and password, which is required to connect to the Internet;
2) Your ISP gave you software such as WinPOET or Enternet300 that you use to connect to the Internet; or 3) You have to double-click on a desktop icon other than your browser to get on the Internet. 26 Using the Web-Based Advanced User Interface 1. User Name This space is provided to type in your user name that was assigned by your ISP. 2. Password Type in your password and re-type it into the Retype Password box to confirm it. 3. Service Name A service name is rarely required by an ISP. If you are not sure if your ISP requires a service name, leave this blank. 4. MTU The MTU setting should never be changed unless your ISP gives you a specific MTU setting. Making changes to the MTU setting can cause problems with your Internet connection including disconnection from the Internet, slow Internet access, and problems with Internet applications working properly. 5. Maximum Idle Time The Maximum Idle Time feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time. For instance, placing a check mark next to this option and entering 5 into the minute field will cause the Router to disconnect from the Internet after five minutes of no Internet activity. This option should be used if you pay for your Internet service by the minute. s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 27 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Setting your Internet Service Provider (ISP) Connection Type to Point-to-Point Tunneling Protocol (PPTP)
[European Countries Only]. Some ISPs require a connection using PPTP protocol, a type of connection most common in European countries. This sets up a direct connection to the ISPs system. Type in the information provided by your ISP in the space provided. When you have finished, click Apply Changes (8). After you apply the changes, if your Router is set up properly, the Internet Status indicator will read Connected.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8) 1. IP Address Provided by your ISP. Enter the IP address here. 2. Subnet Mask Provided by your ISP. Enter your subnet mask here. 3. Default Gateway Provided by your ISP. Enter your default gateway here. 4. User ID Provided by your ISP. Enter your PPTP account name here. 28 Using the Web-Based Advanced User Interface 5. Password Type your password here. Then retype it into the Retype Password box. 6. PPTP Default Gateway 7. Provided by your ISP. Enter your service IP address here. Idle Time Out The Maximum Idle Time feature is used to automatically disconnect the Router from your ISP when there is no activity for a specified period of time. For instance, if you place a check mark next to this option and enter 5 into the minute field, the Router will disconnect from the Internet after five minutes of no Internet activity. This option should be used if you pay for your Internet service by the minute. This feature also allows you to select manual connect, auto connect, and keep session options. s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 29 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Setting Custom Domain Name Server (DNS) Settings A Domain Name Server is a server located on the Internet that translates Universal Resource Locators (URLs) like www.belkin.com into IP addresses. Many Internet Service Providers (ISPs) do not require you to enter this information into the Router. The Automatic from ISP box (1) should be checked if your ISP did not give you a specific DNS address. If you are using a static IP connection type, then you may need to enter a specific DNS address and secondary DNS address for your connection to work properly. If your connection type is dynamic or PPPoE, it is likely that you do not have to enter a DNS address. Leave the Automatic from ISP box checked. To enter the DNS address settings, uncheck the Automatic from ISP box and enter your DNS entries in the spaces provided. Click Apply Changes (2) to save the settings.
(1)
(2) Configuring your WAN Media Access Controller (MAC) Address All network components including cards, adapters, and routers, have a unique serial number called a MAC address. Your Internet Service Provider may record the MAC address of your computers adapter and only let that particular computer connect to the Internet service. When you install the Router, its own MAC address will be seen by the ISP and may cause the connection not to work. Belkin has provided the ability to clone (copy) the MAC address of the computer into the Router. This MAC address, in turn, will be seen by the ISPs 30 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Using the Web-Based Advanced User Interface system as the original MAC address and will allow the connection to work. If you are not sure whether your ISP needs to see the original MAC address, simply clone the MAC address of the computer that was originally connected to the modem. Cloning the address will not cause any problems with your network. Cloning your MAC Address To clone your MAC address, make sure that you are using the computer that was ORIGINALLY CONNECTED to your modem before the Router was installed. Click the Clone button (1). Click Apply Changes (3). Your MAC address is now cloned to the Router. Entering a Specific MAC Address In certain circumstances you may need a specific WAN MAC address. You can manually enter one in the MAC Address page. Type in a MAC address in the spaces provided (2) and click Apply Changes (3) to save the changes. The Routers WAN MAC address will now be changed to the MAC address you specified.
(2)
(1)
(3) 31 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Viewing LAN Settings Clicking on the header of the LAN Setup tab (1) will take you to its header page. A quick description of the functions can be found here. To view the settings or make changes to any of the LAN settings, click on LAN Settings (2) or to view the list of connected computers, click on DHCP Client List (3).
(1)
(2)
(3) 32 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Using the Web-Based Advanced User Interface Changing LAN Settings All settings for the internal LAN setup of the Router can be viewed and changed here.
(1)
(2)
(3)
(4)
(5)
(6) 1. IP Address The IP address is the internal IP address of the Router. The default IP address is 192.168.2.1. To access the Web-Based Advanced User Interface, type this IP address into the address bar of your browser. This address can be changed if needed. To change the IP address, type in the new IP address and click Apply Changes. The IP address you choose should be a non-routable IP. Examples of a non-routable IP are:
192.168.x.x (where x is anything between 0 and 255), and 10.x.x.x (where x is anything between 0 and 255). 2. Subnet Mask There is no need to change the subnet mask. This is a unique, advanced feature of your Belkin Router. It is possible to change the subnet mask if necessary; however, do NOT make changes to the subnet mask unless you have a specific reason to do so. The default setting is 255.255.255.0. 33 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface 3. DHCP Server 4. The DHCP server function makes setting up a network very easy by assigning IP addresses to each computer on the network automatically. The default setting is On. The DHCP server can be turned OFF if necessary; however, in order to do so you must manually set a static IP address for each computer on your network. To turn off the DHCP server, select Off and click Apply Changes. IP Pool The range of IP addresses set aside for dynamic assignment to the computers on your network. The default is 2100 (99 computers). If you want to change this number, you can do so by entering a new starting and ending IP address and clicking on Apply Changes. The DHCP server can assign 100 IP addresses automatically. This means that you cannot specify an IP address pool larger than 100 computers. For example, starting at 50 means you have to end at 150 or lower so as not to exceed the 100-client limit. The starting IP address must be lower in number than the ending IP address. 5. Lease Time The length of time the DHCP server will reserve the IP address for each computer. We recommend that you leave the lease time set to Forever. The default setting is Forever, meaning that any time a computer is assigned an IP address by the DHCP server, the IP address will not change for that particular computer. Setting lease times for shorter intervals such as one day or one hour frees IP addresses after the specified period of time. This also means that a particular computers IP address may change over time. If you have set any of the other advanced features of the Router such as DMZ or client IP filters, these are dependent on the IP address. For this reason, you will not want the IP address to change. 6. Local Domain Name The default setting is Belkin. You can set a local domain name
(network name) for your network. There is no need to change this setting unless you have a specific advanced need to do so. You can name the network anything you want such as MY NETWORK. 34 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Using the Web-Based Advanced User Interface Viewing the DHCP Client List Page You can view a list of the computers (known as clients), which are connected to your network. You are able to view the IP address (1) of the computer, the host name (2) (if the computer has been assigned one), and the MAC address (3) of the computers network interface card (NIC). Pressing the Refresh (4) button will update the list. If there have been any changes, the list will be updated.
(1)
(2)
(3)
(4) 35 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Configuring the Wireless Network Settings The Wireless tab lets you make changes to the wireless network settings. From this tab, you can make changes to the wireless network name (SSID), operating channel, and encryption security settings. You can also configure the Router to be used as an access point.
(1)
(2) Changing the Wireless Network Name (SSID) To identify your wireless network, a name called the SSID (Service Set Identifier) is used. The default SSID of the Router is Belkin Traveler. You can change this to a name of your choice or leave it unchanged. If there are other wireless networks operating in your area, you will want to make sure that your SSID does not match that of another wireless network in the area. To change the SSID, type the SSID that you want to use in the SSID field (1) and click Apply Changes
(2). The change will be effective immediately. If you make a change to the SSID, your wireless-equipped computers may also need to be reconfigured to connect to your newly named network. Refer to the documentation of your wireless network adapter for information on making this change. 36 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Using the Web-Based Advanced User Interface Securing your Wi-Fi Network Here are a few different ways you can maximize the security of your wireless network and protect your data from prying eyes and ears. This section is intended for the home, home office, and small office user. At the time of this User Manuals publication, there are three encryption methods available. Name 64-bit Wired Equivalent Privacy 128-bit Wired Equivalent Privacy Wi-Fi Protected Access-TKIP Wi-Fi Protected Access-AES Acronym 64-bit WEP 128-bit WEP WPA-TKIP WPA-AES Security Good Better Best Best Features Static keys Static keys Dynamic key encryption and mutual authentication Dynamic key encryption and mutual authentication Encryption keys based on RC4 algorithm
(typically 40-bit keys) More secure than 64-bit WEP using a key length of 104 bits plus 24 additional bits of system-
generated data TKIP (temporal key integrity protocol) added so that keys are rotated and encryption is strengthened AES (Advanced Encryption Standard) does not cause any throughput loss WEP (Wired Equivalent Privacy) WEP (Wired Equivalent Privacy) is a common protocol that adds security to all Wi-Fi-compliant wireless products. WEP was designed to give wireless networks the equivalent level of privacy protection as a comparable wired network. 64-Bit WEP 64-bit WEP was first introduced with 64-bit encryption, which includes a key length of 40 bits plus 24 additional bits of system-generated data (64 bits total). Some hardware manufacturers refer to 64-bit as 40-bit encryption. Shortly after the technology was introduced, researchers found that 64-bit encryption was too easy to decode. 37
1 | USER MANUAL 4 OF 7 | Users Manual | 2.88 MiB |
Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface 128-Bit WEP As a result of 64-bit WEPs potential security weaknesses, a more secure method of 128-bit encryption was developed. 128-bit encryption includes a key length of 104 bits plus 24 additional bits of system-generated data (128 bits total). Some hardware manufacturers refer to 128-bit as 104-bit encryption. Most of the new wireless equipment in the market today supports both 64-bit and 128-bit WEP encryption, but you might have older equipment that only supports 64-bit WEP. All Belkin wireless products will support both 64-bit and 128-bit WEP. Encryption Keys After selecting either the 64-bit or 128-bit WEP encryption mode, it is critical that you generate an encryption key. If the encryption key is not consistent throughout the entire wireless network, your wireless networking devices will be unable to communicate with one another on your network and you will not be able to successfully communicate within your network. You can enter your key by typing in the hex key manually, or you can type in a passphrase in the Passphrase field and click Generate to create a key. A hex (hexadecimal) key is a combination of numbers and letters from AF and 09. For 64-bit WEP, you need to enter 10 hex keys. For 128-bit WEP, you need to enter 26 hex keys. For instance:
AF 0F 4B C3 D4 = 64-bit WEP key C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit WEP key The WEP passphrase is NOT the same as a WEP key. Your Router uses this passphrase to generate your WEP keys, but different hardware manufacturers might have different methods on generating the keys. If you have multiple vendors equipment in your network, the easiest thing to do is to use the hex WEP key from your Router or access point and enter it manually into the hex WEP key table in your Routers configuration screen. 38 Using the Web-Based Advanced User Interface WPA (Wi-Fi Protected Access) WPA (Wi-Fi Protected Access) is a new Wi-Fi standard that was designed to improve upon the security features of WEP. To use WPA security, the drivers and software of your wireless equipment must be upgraded to support WPA. These updates will be found on the wireless vendors website. There are two types of WPA security, WPA-PSK (no server) and WPA (with radius server). WPA-PSK (no server) uses what is known as a pre-shared key as the network key. A network key is basically a password that is between eight and 63 characters long. It can be a combination of letters, numbers, or characters. Each client uses the same network key to access the network. Typically, this is the mode that will be used in a home environment. For a list of Belkin wireless products that support WPA, please visit our website at www.belkin.com/networking. s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 39 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Sharing the Same Network Keys Most Wi-Fi products ship with security turned off. So once you have your network working, you need to activate WEP or WPA and make sure your wireless networking devices are sharing the same network key. 40 Using the Web-Based Advanced User Interface Using a Hexadecimal Key A hexadecimal key is a combination of numbers and letters from AF and 09. 64-bit keys are five two-digit numbers. 128-bit keys are 13 two-digit numbers. For instance:
AF 0F 4B C3 D4 = 64-bit key C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit key In the boxes below, make up your key by writing in two characters between AF and 09 in each box. You will use this key to program the encryption settings on your Router and your wireless computers. s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 41 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface WEP Setup 64-Bit WEP Encryption 1. Select 64-bit WEP from the drop-down menu. 2. After selecting your WEP encryption mode, you can enter your key by typing in the hex key manually, or you can type a passphrase in the Passphrase field and click Generate to create a key. A hex (hexadecimal) key is a combination of numbers and letters from AF and 09. For 64-bit WEP, you need to enter 10 hex keys. For instance: AF 0F 4B C3 D4 = 64-bit WEP key 3. Click Apply Changes. Encryption in the Router is now set. Each of the computers on your wireless network will now need to be configured with the same security settings. WARNING: If you are configuring the Wireless G Travel Router or access point from a computer with a wireless client, you will need to ensure that security is turned ON for this wireless client. If this is not done, your client will lose its wireless connection. 42 Using the Web-Based Advanced User Interface 128-Bit WEP Encryption 1. After selecting your WEP encryption mode, you can enter your key by typing in the hex key manually, or you can type a passphrase in the Passphrase field and click Generate to create a key. A hex (hexadecimal) key is a combination of numbers and letters from AF and 09. For 128-bit WEP, you need to enter 26 hex keys. For instance: C3 03 0F AF 0F 4B B2 C3 D4 4B C3 D4 E7 = 128-bit WEP key 2. Click Apply Changes. Encryption in the Router is now set. Each of the computers on your wireless network will now need to be configured with the same security settings. WARNING: If you are configuring the Wireless G Travel Router or access point from a computer with a wireless client, you will need to ensure that security is turned ON for this wireless client. If this is not done, your client will lose its wireless connection. s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 43 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Changing the Wireless Security Settings Your Router is equipped with WPA (Wi-Fi Protected Access), the latest wireless security standard. It also supports the legacy security standard, WEP (Wired Equivalent Privacy). By default, wireless security is disabled. To enable security, you must first determine which standard you want to use. To access the security settings, click Security on the Wireless tab. WPA Setup Note: To use WPA security, all your clients must be upgraded to drivers and software that support it. At the time of this User Manuals publication, a security patch download is available, for free, from Microsoft. This patch works only with the Windows XP operating system. You also need to download the latest driver for your Belkin Wireless G Desktop or Notebook Network Card from the Belkin support site. Other operating systems are not supported at this time. Microsofts patch only supports devices with WPA-enabled drivers such as Belkin 802.11g products. WPA uses a so-called pre-shared key as the security key. A pre-shared key is a password that is between eight and 63 characters long. It can be a combination of letters, numbers, and other characters. Each client uses the same key to access the network. Typically, this mode will be used in a home environment. WPA2 is the second generation of WPA, offering a more advanced encryption technique over WPA. 44 Using the Web-Based Advanced User Interface WPA/WPA2 Setup 1. Select WPA/WPA2 or WPA2 only from the Allowed Client Type. 2. Select Pre-shared key as the authentication type. 3. Enter your pre-shared key. This can be from eight to 63 characters and can be letters, numbers, or symbols. This same key must be used on all of the clients that you set up. This pre-shared key will allow users full access to your network including shared files and printers. 4. Click Apply Changes to finish. You must now set all clients to match these settings. 5. Enter your pre-shared key for guest access. This can be from eight to 63 characters and can be letters, numbers, or symbols. This guest pre-shared key allows users only Internet access. 6. Click Apply Changes to finish. You must now set all clients to match these settings depending on the type of access you want them to have. s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 45 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Setting WPA-PSK (no server) 1. From the Security Mode drop-down menu, select WPA-PSK (no server). 2. For Encryption Technique, select TKIP or AES. This setting will have to be identical on the clients that you set up. 3. Enter your pre-shared key. This can contain eight to 63 characters (letters, numbers, and/or symbols). This same key must be used on all of the clients that you set up. For example, your PSK might be something like: Smith family network key. 4. Click Apply Changes. You must now configure all clients to match these settings. Configuring your Belkin Wireless G Cards to Use Security Features Please Note: This section will provide you with information on how to configure your Belkin Wireless G Cards to use security features. At this point, you should already have your Router or access point set up to use WPA or WEP. To establish a wireless connection, you will need to set up your Wireless Notebook Card and Wireless Desktop Card to use the same security settings. 46 Using the Web-Based Advanced User Interface Connecting your computer to a wireless network that requires a 64-bit or 128-bit WEP key:
1. Double-click the Signal Indicator icon to bring up the Wireless Network screen. The Advanced button will allow you to view and configure more Router options. 2. Under the Wireless Network Properties tab, select a network name from the Available Networks list and click Configure. 3. Under Data Encryption, select WEP. 4. Ensure that there is no check in the box next to Network key is provided for me automatically. If you are using this computer to connect to a corporate network, please ask your network administrator whether this box needs to be checked. 5. Type your WEP key in the network key box (designated as Key in Belkins wireless configuration utility). s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Important: A WEP key is a combination of numbers and letters from AF and 09. For 128-bit WEP, you need to enter 26 keys. For 64-bit WEP, you need to enter 10 keys. This network key needs to match the key you assign to your Router or access point. 6. Click OK. 47 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Connecting your computer to a wireless network that requires WPA-PSK (no server):
1. Double-click the Signal Indicator icon to bring up the Wireless Network screen. The Advanced button will allow you to view and configure more Router options. 2. Under the Wireless Networks tab, select a network name from the Available networks list and click Configure. 3. Under Network Authentication, select WPA-PSK (No Server). 4. Type your WPA key in the network key box, designated as Key on Belkins wireless configuration utility. Important: WPA-PSK is a combination of numbers and letters from AZ and 09. For WPA-PSK, your key can contain from eight to 63 keys. This network key needs to match the key you assign to your Router or access point. 5. Click OK. 48 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Using the Web-Based Advanced User Interface Connecting your computer to a wireless network that requires WPA (with radius server):
1. Double-click the Signal Indicator icon to bring up the Wireless Network screen. The Advanced button will allow you to view and configure more Router options. 2. Under the Wireless Networks tab, select a network name from the Available networks list and click Configure. 3. Under Network Authentication, select WPA. 4. Under the Authentication tab, select the settings that are indicated by your network administrator. 5. Click OK. Setting Up WPA for Wireless Desktop and Wireless Notebook Cards that are NOT Manufactured by Belkin If you do NOT have a Belkin WPA Wireless Desktop or Wireless Notebook Card and your computer is not equipped with WPA-enabled software, download Microsofts Windows XP Support Patch for Wireless Protected Access, which is available for free download. Please Note: The file that Microsoft has made available works only with Windows XP. Other operating systems are not supported at this time. Important: You also need to ensure that the wireless-card manufacturer supports WPA and that you have downloaded and installed the latest driver from the manufacturers support site. Supported Operating Systems:
Windows XP Professional Windows XP Home Edition Setting Up Windows XP Wireless Network Utility to Use WPA-PSK In order to use WPA-PSK, ensure you are using the Windows Wireless Network Utility by doing the following:
1. Under Windows XP, click Start > Control Panel > Network Connections. 2. Right-click on Wireless Network Connection Properties, and select Properties. 49 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface 3. Clicking on the Wireless Networks tab will display the following screen. Ensure the Use Windows to configure my wireless network settings box is checked. 4. Under the Wireless Networks tab, click the Configure button and you will see the following screen. 50
1 | USER MANUAL 5 OF 7 | Users Manual | 2.89 MiB |
Using the Web-Based Advanced User Interface 5. For a home or small business user, select WPA-PSK under Network Authentication. Note: Select WPA if you are using this computer to connect to a corporate network that supports an authentication server such as a radius server. Please consult your network administrator for further information. 6. Select TKIP or AES under Data Encryption. This setting will have to be identical to the Router that you set up. 7. Type in your encryption key in the Network key box. Important: Enter your pre-shared key. This can be from eight to 63 characters and can be letters, numbers, or symbols. This same key must be used on all of the clients that you set up. 8. Click OK to apply settings. s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 51 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Utilities Tab This screen lets you manage different parameters of the Router and perform certain administrative functions. 52 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Using the Web-Based Advanced User Interface Restarting the Router Sometimes it may be necessary to restart or reboot the Router if it begins working improperly. Restarting or rebooting the Router will NOT delete any of your configuration settings. Restarting the Router to Restore Normal Operation 1. Click the Restart Router button. 2. The following message will appear. Click OK. 3. The following message will appear. Restarting the Router can take up to 25 seconds. It is important not to turn off the power to the Router during the restart. 4. A 25-second countdown will appear on the screen. When the countdown reaches zero, the Router will be restarted. The Routers home page should appear automatically. If not, type in the Routers address (default = 192.168.2.1) into the navigation bar of your browser. 53 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Restoring Factory Default Settings Using this option will restore all of the settings in the Router to the factory (default) settings. It is recommended that you back up your settings before you restore all of the defaults. 1. Click the Restore Defaults button. 2. The following message will appear. Click OK. 3. The following message will appear. Restoring the defaults includes restarting the Router. It can take up to 25 seconds. It is important not to turn the power to the Router off during the restart. 4. A 25-second countdown will appear on the screen. When the countdown reaches zero, the Routers defaults will be restored. The Routers home page should appear automatically. If it does not, type in the Routers address (default = 192.168.2.1) into the navigation bar of your browser. 54 s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Using the Web-Based Advanced User Interface Saving a Current Configuration You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed. It is recommended that you back up your current configuration before performing a firmware update. 1. Click Save. A window called File Download will open. Click Save. 2. A window will open that allows you to select the location where you want to save the configuration file. Select a location. You can name the file anything you want, or use the default name Config. Be sure to name the file so you can locate it yourself later. When you have selected the location and name of the file, click Save. 55 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface 3. When the save is complete, you will see the following window. Click Close. The configuration is now saved. Restoring a Previous Configuration This option will allow you to restore a previously saved configuration. 1. Click Browse. A window will open that allows you to select the location of the configuration file. All configuration files end with a .bin. Locate the configuration file you want to restore and double-click on it. 56 Using the Web-Based Advanced User Interface 2. You will be asked if you want to continue. Click OK. 3. A reminder window will appear. It will take up to 35 seconds for the configuration restoration to complete. Click OK. 4. A 35-second countdown will appear on the screen. When the countdown reaches zero, the Routers configuration will be restored. The Routers home page should appear automatically. If not, type in the Routers address (default = 192.168.2.1) into the navigation bar of your browser. s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 57 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface Updating the Firmware From time to time, Belkin may release new versions of the Routers firmware. Firmware updates contain feature improvements and fixes to problems that may exist. When Belkin releases new firmware, you can download the firmware from the Belkin update website and update your Routers firmware to the latest version. Searching for a New Version of Firmware From http://www.belkin.com/support/downloads.asp, type in the Belkin part number F5D7233 on the Search field. Click Search. From the results page, click F5D7233 Firmware update -
North America. 58 Using the Web-Based Advanced User Interface Downloading a New Version of Firmware You will now be taken to the download page of F5D7233 Firmware update - North America. 1. To download the new version of firmware, click the download logo (
). 2. A window will open that allows you to select the location where 1 2 3 4 5 6 7 8 9 s e c t i o n you want to save the firmware file. Select a location. You can name the file anything you want, or use the default name. Be sure to save the file in a place where you can locate it yourself later. Note: We suggest saving this to your desktop to make it easy to locate the file. When you have selected the location, click Save. 10 11 59 Using the Web-Based Advanced User Interface Using the Web-Based Advanced User Interface 3. When the save is complete, you will see the following window. Click Close. The download of the firmware is complete. To update the firmware, follow the next steps in Updating the Routers Firmware. Updating the Routers Firmware 1. In the Firmware Update page, click Browse. A window will open that allows you to select the location of the firmware update file. 2. Browse to the firmware file you downloaded. Select the file by double-clicking on the file name. 60
1 | USER MANUAL 6 OF 7 | Users Manual | 2.60 MiB |
s e c t i o n 1 2 3 4 5 6 7 8 9 10 11 Using the Web-Based Advanced User Interface 3. The Update Firmware box will now display the location and name of the firmware file you just selected. Click Update. 4. You will be asked if you are sure you want to continue. Click OK. 5. You will see one more message. This message tells you that the Router may not respond for as long as one minute as the firmware is loaded into the Router and the Router is rebooted. Click OK. 6. A 60-second countdown will appear on the screen. When the countdown reaches zero, the Routers firmware update will be complete. The Routers home page should appear automatically. If not, type in the Routers address (default = 192.168.2.1) into the navigation bar of your browser. The firmware update is complete. 61 Manually Configuring Network Settings In order for your computer to properly communicate with your Router, you will need to change your PCs TCP/IP settings to DHCP. Manually Configuring Network Adapters in Windows 2000, NT, or XP 1. Click Start, Settings, then Control Panel. 2. Double-click on the Network and dial-up connections icon
(Windows 2000) or the Network icon (Windows XP). 3. Right-click on the Local Area Connection associated with your 4. network adapter and select Properties from the drop-down menu. In the Local Area Connection Properties window, click Internet Protocol (TCP/IP) and click the Properties button. The following screen will appear:
(1)
(2)
(3) 5. If Use the following IP address (2) is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router. 6. If not already selected, select Obtain an IP address automatically
(1) and Obtain DNS server address automatically (3). Click OK. Your network adapter/s is/are now configured for use with the Router. 62 1 2 3 4 5 6 7 8 9 10 11 s e c t i o n Manually Configuring Network Settings Manually Configuring Network Adapters in Windows 98SE or Me 1. Right-click on My Network Neighborhood and select Properties from the drop-down menu. 2. Select TCP/IP -> settings for your installed network adapter. You will see the following window.
(1)
(2)
(3) 3. If Specify an IP address is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below. You will need to enter this information into the Router. 4. Write in the IP address and subnet mask from the IP Address tab (3). 5. Click the Gateway tab (2). Write the gateway address down in the chart. 6. Click the DNS Configuration tab (1). Write the DNS address(es) 7. in the chart. If not already selected, select Obtain IP address automatically in the IP Address tab. Click OK. Restart the computer. When the computer restarts, your network adapter/s is/are now configured for use with the Router. 63 Recommended Web Browser Settings In most cases, you will not need to make any changes to your web browsers settings. If you are having trouble accessing the Internet or the Web-Based Advanced User Interface, then change your browsers settings to the recommended settings in this section. Internet Explorer 4.0 or Higher 1. Start your web browser. Select Tools then Internet Options. In the Internet Options screen, there are three selections:
Never dial a connection, Dial whenever a network connection is not present, and Always dial my default connection. If you can make a selection, select Never dial a connection. If you cannot make a selection, go to the next step. 2. 3. Under the Internet Options screen, click on Connections and select LAN Settings. 64 Recommended Web Browser Settings 4. Make sure there are no check marks next to any of the displayed options: Automatically detect settings, Use automatic configuration script, and Use a proxy server. Click OK. Then click OK again in the Internet Options page. Netscape Navigator 4.0 or Higher 1. Start Netscape. Click on Edit then Preferences. 2. In the Preferences window, click on Advanced then select Proxies. In the Proxies window, select Direct connection to the Internet. 1 2 3 4 5 6 7 8 9 10 11 s e c t i o n 65 Using the Access Point Mode Using the Access Point Mode Using the Adapter Mode Using the Access Point Mode Note: This advanced feature should be employed by advanced users only. The Router can be configured to work as a wireless-network access point. Using this mode will defeat the NAT IP sharing feature and DHCP server. In Access Point (AP) mode, the Router will need to be configured with an IP address that is in the same subnet as the rest of the network to which you will bridge. The default IP address is 192.168.2.254 and the default subnet mask is 255.255.255.0. These can be customized to meet your needs. 1. Move the center of the button on the back panel to align with the word AP. 2. Enable the AP mode my selecting Enable in the Use as Access Point only page. When you select this option, you will be able to change the IP settings. 3. Set your IP settings to match your network. Click Apply Changes. 4. Connect a cable from the WAN port on the Router to your existing network. The Router is now acting as an access point. To access the Routers Web-Based Advanced User Interface again, type the IP address you specified into your browsers navigation bar. You can set the encryption settings, MAC address filtering, SSID, and channel normally. 666666 Using the Adapter Mode Setting Up your Computer to Use the Web-Based Advanced User Interface The default IP address of the Router (while functioning in Adapter Mode) is 192.168.2.225. You will need to set your computers IP address to the same subnet (e.g., 192.168.2.224) before you can access the Web-Based Advanced User Interface. Perform the following steps from Windows 98SE, Me, 2000, or XP:
1. Move the center of the switch on the back panel to align with the word Adapter. 2. Go to the Windows Control Panel and double-click on the Network icon or the Network Connections icon. 3. Right-click on the Local Area Connection button for your Router and select Properties. 1 2 3 4 5 6 7 8 9 10 11 s e c t i o n 4. In the General window, select the Internet Protocol TCP/IP settings for your Router and click on Properties. 5. Select the Use the following IP address radio button. 676767 Using the Adapter Mode Using the Adapter Mode 6. Enter an IP address in the same subnet as the access point (for example, 192.168.2.224). 7. Enter the following subnet mask: 255.255.255.0. Click OK. Warning: Once you have configured your Router, you must repeat steps 1 through 3 and select Obtain an IP automatically or set a valid IP for your computer on the same subnet as the network to which you are connecting. Connect Using Adapter Mode Using your Internet browser, you can access the Web-Based Advanced User Interface. In your browser, type 192.168.2.225 (do not type in http:// or www). Then press the Enter key. Logging into the Web-Based Advanced User Interface You will see the Web-Based Advanced User Interface home page in your browser window. The home page is visible to any user who wants to see it. To make any changes to the Routers settings, you have to log in. Clicking the Login button or clicking on any one of the links on the home page will take you to the login screen. The Router ships with no password. In the login screen, leave the password blank and click Submit to log in. 68 1 2 3 4 5 6 7 8 9 10 11 s e c t i o n Using the Adapter Mode Logging Out of the Web-Based Advanced User Interface One computer at a time can log into the Router to make changes to the Routers settings. Once a user has logged in to make changes, there are two ways that the computer can be logged out. The first is to click the Logout button. The second method is automatic. The login will time out after a specified period of time. The default login time-out is 10 minutes. This can be changed to any period of time from 1 to 99 minutes. Login Time-Out The login time-out option allows you to set the period of time that you can be logged into the Routers Web-Based Advanced User Interface. The timer starts when activity stops. For example, you have made some changes in the Web-Based Advanced User Interface, and then left your computer alone without clicking Logout. If the time-out is set to 10 minutes (the default setting), then 10 minutes after you leave, the login session will expire. You will have to log into the Router again to make any more changes. The login time-out option provides additional security. Note: Only one computer can be logged into the Routers Web-Based Advanced User Interface at one time. 69 Using the Adapter Mode Using the Adapter Mode Understanding the Web-Based Advanced User Interface The home page is the first page you will see when you access the Web-Based Advanced User Interface (UI). The home page provides a quick view of the Routers status and settings. All setup pages can be reached from this page.
(4)
(3)
(1)
(2) Status 1. Quick-Navigation Links You can go directly to any of the pages by clicking directly on these links. The links are divided into logical categories and grouped by tabs to make finding a particular setting easy. 2. Version Information Shows the firmware version, boot-code version, and hardware version. 3. LAN Settings Shows the settings of the Local Area Network (LAN) side of the Router. Changes can be made to the settings by clicking the quick-navigation links on the left side of the screen. 4. Wireless Connection Shows the status of the Routers wireless setting. Changes can be made to the settings by clicking the quick-navigation links on the left side of the screen. 70
1 | USER MANUAL 7 OF 7 | Users Manual | 915.25 KiB |
1 2 3 4 5 6 7 8 9 10 11 s e c t i o n Using the Adapter Mode Connect to a Wireless Network Click Networks Available from the quick-navigation links.
(1)
(2)
(3)
(4)
(5)
(6)
(7) Site Survey List 1. Scan Clicking the Scan button will give you the most up-to-date data list of available networks. 2. SSID The SSID is the wireless network name. 3. BSSID/MAC Address This gives the MAC address of the available network. 4. Encryption Identifies the type of network security implemented (WPA or WEP). This field will show a blank if the network is unsecured. 5. Channel Identifies which channel the network is on. 6. Signal Strength Provides a measurement of the networks signal strength. 7. Join You can connect to a specific wireless network by selecting the check box and clicking Apply Changes. 71 Using the Adapter Mode Troubleshooting Using the Adapter Mode Troubleshooting Using the Adapter Mode Restart Client You can restart your Router (in Adapter Mode) without losing any of your configuration settings by clicking Restart Client. Restore Factory Defaults Clicking Restore Factory Default will erase all your current settings. Save Backup Settings You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed. It is recommended that you back up your current configuration before performing a firmware update. Restore Previous Settings This option will allow you to restore a previously saved configuration. Firmware Update From time to time, Belkin may release new versions of the Routers firmware. Updates contain improvements and fixes to known problems. For the latest firmware, go to the support section of www.belkin.com/networking. a. Browse:
Clicking on Browse will open a window that allows you to select the location of the firmware-update file. b. Upgrade:
Clicking on Upgrade will update your Router to the latest firmware. 727272 Troubleshooting Problem:
Installation CD does not automatically start. Solution:
If the CD-ROM does not start the Easy Install Wizard automatically, it could be that the computer is running other applications that are interfering with the CD drive. 1. If the Easy Install Wizard screen does not appear within 1520 seconds, open up your CD-ROM drive by double-clicking on the My Computer icon that is located on your desktop. 2. Next, double-click on the CD-ROM drive that the Easy Install Wizard Software CD has been placed in to start the installation. 3. The Easy Install Wizard should start within a few seconds. If, instead, a window appears showing the files on the CD, double-click on the icon labeled EasyInstall.exe. 1 2 3 4 5 6 7 8 9 10 11 s e c t i o n 737373 Troubleshooting Troubleshooting Problem:
The Easy Install Wizard cannot find my Router. Solution:
If the Easy Install Wizard is not able to find the Router during the installation process, please check the following items:
1. Check to see if the switch on the back of the Router has been set to Router Mode. 2. Unplug power to the Router for 10 seconds, and then plug the power back into the Router. Ensure that the Routers Power light is on; it should be solid green. If not, check to make sure that the AC adapter is correctly connected to the Router and plugged into a wall outlet. 3. Check to see if the switch on the back of the Router has been set to Router Mode. Problem:
The Easy Install Wizard cannot connect my Router to the Internet. Solution:
If the Easy Install Wizard is not able to connect the Router to the Internet, please check the following items:
1. Ensure that you have a cable (use the cable included with the Router) connected between (1) the Ethernet port on the back of the Router to the (2) Ethernet port of your modem or service provider. 2. If your ISP requires a user name and password, make sure that you have typed in your user name and password correctly. Some user names require that the ISPs domain be at the end of the name. Example: myname@myisp.com. The @myisp.com part of the user name may need to be typed as well as your user name. Problem:
The Easy Install Wizard completed installation and the Routers Ethernet light is lit On but my web browser doesnt work. Solution:
1. Make sure the network cable between the modem and the Router is connected. We strongly recommend using the cable that was supplied with your cable or DSL modem for this purpose. The cable should be connected at one end to the Routers Ethernet port, and at the other end to the network port on your modem or service provider. 74 Troubleshooting 1 2 3 4 5 6 7 8 9 10 11 s e c t i o n 2. Unplug the cable or DSL modem from its power source for three minutes. After three minutes, plug the modem back into its power source. This may force the modem to properly recognize the Router. 3. Unplug the power to your Router, wait 10 seconds, and then reconnect the power. This will cause the Router to reattempt communication with the modem. If the Ethernet light on the Router is not lit after completing these steps, please contact Belkin Technical Support. 4. Try shutting down and restarting your computer. 5. If you have a static IP address connection, your ISP must assign you the IP address, subnet mask, and gateway address. 6. If you have a PPPoE connection, your ISP will assign you a user name and password and sometimes a service name. Make sure the Router connection type is configured to PPPoE and the settings are entered properly. 7. You may need to configure your Router to meet the specific requirements of your ISP. To search our Knowledge Base for ISP-specific issues, go to: http://web.belkin.com/support and type in ISP. If you are still unable to access the Internet after verifying these settings, please contact Belkin Technical Support. Problem:
I cant connect to the Internet wirelessly. Solution:
If you are unable to connect to the Internet from a wireless computer, please do the following:
1. Look at the lights on your Router. Your Belkin Routers lights should be as follows:
The Power light should be on. The Connected light should be on and not blinking. The WAN light should be either on or blinking. 75 Troubleshooting Troubleshooting 2. Open your wireless utility software by clicking on the icon in the system tray at the bottom, right-hand corner of the screen. If you are also using a Belkin Wireless Card or Adapter with this Router, the tray icon should look like this (the icon may be red or green):
3. The exact window that opens will vary depending on the model of wireless card you have; however, any of the utilities should have a list of Available Networksthose wireless networks it can connect to. Does the name of your wireless network appear in the results?
Yes, my network name is listedgo to the troubleshooting solution titled I cant connect to the Internet wirelessly, but my network name is listed. No, my network name is not listedgo to the troubleshooting solution titled I cant connect to the Internet wirelessly, and my network name is not listed. Problem:
I cant connect to the Internet wirelessly, but my network name is listed. Solution:
If the name of your network is listed in the Available Networks list, please follow the steps below to connect wirelessly:
1. Click on the correct network name in the Available Networks list. 2. If the network has security (encryption) enabled, you will need to enter the network key. For more information regarding security, see the section entitled Securing your Wi-Fi Network in this User Manual. 3. Within a few seconds, the tray icon in the lower, left-hand corner of your screen should turn green, indicating a successful connection to the network. 76 1 2 3 4 5 6 7 8 9 10 11 s e c t i o n Troubleshooting Problem:
I cant connect to the Internet wirelessly, and my network name is not listed. Solution:
If the correct network name is not listed under Available Networks in the wireless configuration utility, please attempt the following troubleshooting steps:
1. Temporarily move your computer, if possible, five to 10 feet away from the Router. Close the wireless configuration utility, and reopen it. If the correct network name now appears under Available Networks, you may have a range or interference problem. Please see the suggestions discussed in the section titled Placement of your Router for Optimal Performance in this User Manual. 2. Using a computer that is connected to the Router through a network cable (as opposed to wirelessly), ensure that Broadcast SSID is enabled. This setting is found on the Routers wireless Channel and SSID configuration page. If you are still unable to access the Internet after completing these steps, please contact Belkin Technical Support. Problem:
My wireless network performance is inconsistent. Data transfer is sometimes slow. Signal strength is poor. I am having difficulty establishing and/or maintaining a Virtual Private Network (VPN) connection. Solution:
Wireless technology is radio-based, which means connectivity and the throughput performance between devices decreases when the distance between devices increases. Other factors that will cause signal degradation (metal is generally the worst culprit) are obstructions such as walls and metal appliances. As a result, the typical indoor range of your wireless devices will be between 100 to 200 feet. Note also that connection speed may decrease as you move farther away from the Router or access point. 77 Troubleshooting Troubleshooting In order to determine if wireless issues are related to range, we suggest temporarily moving the computer, if possible, five to 10 feet away from the Router. Changing the Wireless ChannelDepending on local wireless traffic and interference, switching the wireless channel of your network can improve performance and reliability. The default channel the Router is shipped with is channel 11. Limiting the Wireless Transmit RateLimiting the wireless transmit rate can help improve the maximum wireless range, and connection stability. Most wireless cards have the ability to limit the transmission rate. To change this property, go to the Windows Control Panel, open Network Connections and double-click on your wireless cards connection. In the Properties dialog, select the Configure button on the General tab (Windows 98 users will have to select the wireless card in the list box and then click Properties), then choose the Advanced tab and select the rate property. Wireless client cards are usually set to automatically adjust the wireless transmit rate for you, but doing so can cause periodic disconnects when the wireless signal is too weak; as a rule, slower transmission rates are more stable. Experiment with different connection rates until you find the best one for your environment;
note that all available transmission rates should be acceptable for browsing the Internet. For more assistance, see your wireless cards user manual. 78 Troubleshooting Technical Support You can find technical support information at:
http://www.belkin.com/networking or www.belkin.com through the tech support area. If you want to contact technical support by phone, please call:
877-736-5771 or US:
310-898-1100 ext. 2263 00 800 223 55 460 Europe:
Australia:
1800 235 546 New Zealand: 0800 235 546 Singapore:
800 616 1790 1 2 3 4 5 6 7 8 9 10 11 s e c t i o n 79 Information FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin Corporation, of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the product, F5D7233 to which this declaration relates, complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Exposure to Radio Frequency Radiation. The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized. When connecting an external antenna to the device, the antenna shall be placed in such a manner to minimize the potential for human contact during normal operation. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
80 1 2 3 4 5 6 7 8 9 10 11 s e c t i o n Information Reorient or relocate the receiving antenna. Increase the distance between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Modifications The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by Belkin Corporation may void the users authority to operate the equipment. Canada-Industry Canada (IC) The wireless radio of this device complies with RSS 139 & RSS 210 Industry Canada. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B conforme la norme NMB-003 du Canada. Europe-European Union Notice Radio products with the CE 0682 or CE alert marking comply with the R&TTE Directive (1995/5/EC) issued by the Commission of the European Community. Compliance with this directive implies conformity to the following European Norms (in brackets are the equivalent international standards). EN 60950 (IEC60950) Product Safety EN 300 328 Technical requirement for radio equipment ETS 300 826 General EMC requirements for radio equipment. To determine the type of transmitter, check the identification label on your Belkin product. Products with the CE marking comply with the EMC Directive (89/336/EEC) and the Low Voltage Directive (72/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms (in brackets are the equivalent international standards). Products that contain the radio transmitter are labeled with CE 0682 or CE alert marking and may also carry the CE logo. EN 55022 (CISPR 22) Electromagnetic Interference EN 55024 (IEC61000-4-2,3,4,5,6,8,11) Electromagnetic Immunity EN 61000-3-2 (IEC610000-3-2) Power Line Harmonics EN 61000-3-3 (IEC610000) Power Line Flicker EN 60950 (IEC60950) Product Safety 81 Information Information Belkin Corporation Limited Lifetime Product Warranty Belkin Corporation warrants this product against defects in materials and workmanship for its lifetime. If a defect is discovered, Belkin will, at its option, repair or replace the product at no charge provided it is returned during the warranty period, with transportation charges prepaid, to the authorized Belkin dealer from whom you purchased the product. Proof of purchase may be required. This warranty does not apply if the product has been damaged by accident, abuse, misuse, or misapplication; if the product has been modified without the written permission of Belkin; or if any Belkin serial number has been removed or defaced. THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE IN LIEU OF ALL OTHERS, WHETHER ORAL OR WRITTEN, EXPRESSED OR IMPLIED. BELKIN SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No Belkin dealer, agent, or employee is authorized to make any modification, extension, or addition to this warranty. BELKIN IS NOT RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO, LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPROGRAMMING OR REPRODUCING ANY PROGRAM OR DATA STORED IN, OR USED WITH, BELKIN PRODUCTS. Some states do not allow the exclusion or limitation of incidental or consequential damages or exclusions of implied warranties, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. 82 Wireless G Travel Router Belkin Ltd. 7 Bowen Crescent, West Gosford NSW 2250, Australia
+61 (0) 2 4372 8600
+61 (0) 2 4372 8603 fax Belkin B.V. Boeing Avenue 333 1119 PH Schiphol-Rijk, The Netherlands
+31 (0) 20 654 7300
+31 (0) 20 654 7349 fax Belkin Tech Support US: 877-736-5771 310-898-1100 ext. 2263 Europe: 00 800 223 55 460 Australia: 1800 235 546 New Zealand: 0800 235 546 Singapore: 800 616 1790 Belkin Corporation 501 West Walnut Street Compton, CA 90220-5221, USA 310-898-1100 310-898-1111 fax Belkin Ltd. Express Business Park, Shipton Way Rushden, NN10 6GL, United Kingdom
+44 (0) 1933 35 2000
+44 (0) 1933 31 2000 fax 2005 Belkin Corporation. All rights reserved. All trade names are registered trademarks of respective manufacturers listed. The mark Wi-Fi is a registered mark of the Wi-Fi Alliance. P74841
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2005-10-13 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2005-10-13
|
||||
1 | Applicant's complete, legal business name |
Arcadyan Technology Corporation
|
||||
1 | FCC Registration Number (FRN) |
0009258708
|
||||
1 | Physical Address |
No.8, Sec.2, Guangfu Rd.
|
||||
1 |
Hsinchu, N/A
|
|||||
1 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
T******@TIMCOENGR.COM
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
RAX
|
||||
1 | Equipment Product Code |
WA4001CB
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
S******** L********
|
||||
1 | Title |
Manager
|
||||
1 | Telephone Number |
886-3******** Extension:
|
||||
1 | Fax Number |
886-3********
|
||||
1 |
s******@arcadyan.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | WLAN ACCESS POINT | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Powere Listed Is Conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Sporton International Inc.
|
||||
1 | Name |
K****** L****
|
||||
1 | Telephone Number |
886-2******** Extension:
|
||||
1 | Fax Number |
886-2********
|
||||
1 |
k******@sporton.com.tw
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2412.00000000 | 2462.00000000 | 0.2460000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC