| submitted | available | document details (if available) | source link |
|---|---|---|---|
| December 12 2016 | December 12 2016 | Microsoft Word - TG3482G-NA Users Guide.doc blewis Nuance PDF Create 8 |
| various | Users Guide | Users Manual | 1.59 MiB | December 12 2016 |
Touchstone TG3482 Telephony Gateway User Guide Release 34 DRAFT 1.0 July 2016 July 2016 Draft Only Touchstone TG3482 Telephony Gateway User Guide Release 34 DRAFT 1.0 ARRIS Copyrights and Trademarks 2016 ARRIS Enterprises LLC. All Rights Reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from ARRIS Enterprises, LLC. (ARRIS). ARRIS reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of ARRIS to provide notification of such revision or change. ARRIS and the ARRIS logo are all trademarks of ARRIS Enterprises, LLC. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and the names of their products. ARRIS disclaims proprietary interest in the marks and names of others. ARRIS provides this guide without warranty of any kind, implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. ARRIS may make improvements or changes in the product(s) described in this manual at any time. The capabilities, system requirements and/or compatibility with third-party products described herein are subject to change without notice. Patent Notice Protected under one or more of the following U.S. patents: http://www.arris.com/legal Other patents pending. Draft Only Table of Contents 1. 2. 3. Safety Requirements............................................................................................... 5 FCC Part 15 ........................................................................................................................ 6 RF Exposure............................................................................................................... 7 Industry Canada Compliance............................................................................................. 7 For Mexico ......................................................................................................................... 7 European Compliance........................................................................................................ 7 Getting Started ....................................................................................................... 9 Introduction....................................................................................................................... 9 About Your New Telephony Gateway ............................................................................... 9 What's in the Box............................................................................................................. 10 Items You Need ............................................................................................................... 10 Getting Service................................................................................................................. 11 System Requirements...................................................................................................... 12 Recommended Hardware....................................................................................... 12 Windows ................................................................................................................. 12 Mac OS.................................................................................................................... 12 Linux/Unix ............................................................................................................... 12 About this Manual ........................................................................................................... 13 What about Security?...................................................................................................... 13 Ethernet or Wireless?...................................................................................................... 14 Getting Support ............................................................................................................... 15 Installing and Connecting your Telephony Gateway............................................... 16 Front Panel ...................................................................................................................... 17 Rear Panel........................................................................................................................ 18 Selecting an Installation Location.................................................................................... 18 Desktop Mounting Instructions .............................................................................. 19 Factors Affecting Wireless Range ........................................................................... 19 Connecting the Telephony Gateway ............................................................................... 20 Configuring Your Wireless Connection............................................................................ 21 Accessing the Configuration Interface.................................................................... 21 Setting Parental Controls................................................................................................. 22 Finding the MAC Address of a Computer ............................................................... 22 Making Your Parental Control Settings................................................................... 22 4. Configuring Your Ethernet Connection................................................................... 25 Requirements .................................................................................................................. 25 Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 3 Draft Only How to use this Chapter .................................................................................................. 25 TCP/IP Configuration for Windows Vista......................................................................... 25 TCP/IP Configuration for Windows 7, Windows 8, or Windows 10 ................................ 26 TCP/IP Configuration for Mac OS X ................................................................................. 26 5. 6. Using the Telephony Gateway............................................................................... 28 Setting up Your Computer to Use the Telephony Gateway ............................................ 28 Indicator Light for the TG3482 ........................................................................................ 28 Wiring Problems ..................................................................................................... 29 Using the Reset Button........................................................................................... 29 Resetting the Router to Factory Defaults ............................................................... 30 Troubleshooting.................................................................................................... 31 The Telephony Gateway is plugged in, but the Power light is Off .................................. 31 I'm not getting on the Internet (all connections)............................................................ 31 I'm not getting on the Internet (Ethernet) ...................................................................... 31 I'm not getting on the Internet (Wireless)....................................................................... 32 My wireless Internet connection stops working sometimes .......................................... 32 I can get on the Internet, but everything is slow ............................................................ 32 I don't have a dial tone when I pick up the phone - why? .............................................. 32 7. Glossary................................................................................................................ 34 Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 4 Draft Only Chapter 1 Safety Requirements The ARRIS Telephony Gateway complies with the applicable requirements for performance, construction, labeling, and information when used as outlined below:
CAUTION Potential equipment damage Potential loss of service Connecting the Telephony Gateway to existing telephone wiring should only be performed by a professional installer. Physical connections to the previous telephone provider must be removed and the wiring must be checked; there must not be any voltages. Cancelation of telephone service is not adequate. Failure to do so may result in loss of service and/or permanent damage to the Telephony Gateway. CAUTION Risk of shock Mains voltages inside this unit. No user serviceable parts inside. Refer service to qualified personnel only!
CAUTION Risk of explosion Replacing the battery with an incorrect type, heating a battery above 75C, or incinerating a battery, can cause product failure and a risk of fire or battery explosion. Do not dispose of in fire. Recycle or dispose of used batteries responsibly and in accordance with local ordinances. The Telephony Gateway is designed to be connected directly to a telephone. Connecting the Telephony Gateway to the homes existing telephone wiring should only Do not use product near water (i.e. wet basement, bathtub, sink or near a swimming pool, be performed by a professional installer. etc.), to avoid risk of electrocution. Do not use the telephone to report a gas leak in the vicinity of the leak. The product shall be cleaned using only a damp, lint-free, cloth. No solvents or cleaning agents shall be used. Do not use spray cleaners or aerosols on the gateway. Avoid using and/or connecting the equipment during an electrical storm, to avoid risk of electrocution. Do not locate the equipment within 6 feet (1.9 m) of a flame or ignition source (i.e. heat registers, space heaters, fireplaces, etc.). Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 5 Draft Only Chapter 1: Safety Requirements Use only the AC power adapter (if provided) and power cord included with the equipment. Equipment should be installed near the power outlet and should be easily accessible. The shield of the coaxial cable must be connected to earth (grounded) at the entrance to the building in accordance with applicable national electrical installation codes. In the U.S., this is required by NFPA 70 (National Electrical Code) Article 820. In the European Union and in certain other countries, CATV installation equipotential bonding requirements are specified in IEC 60728-11, Cable networks for television signals, sound signals and interactive services, Part 11: Safety. This equipment is intended to be installed in accordance with the requirements of IEC 60728-11 for safe operation. If the equipment is to be installed in an area serviced by an IT power line network, as is found in many areas of Norway, special attention should be given that the installation is in accordance with IEC 60728-11, in particular Annex B and Figure B.4. In areas of high surge events or poor grounding situations and areas prone to lightning strikes, additional surge protection may be required (i.e. PF11VNT3 from American Power Conversion) on the AC, RF, Ethernet and Phone lines. When the Telephony Gateway is connected to a local computer through Ethernet cables, the computer must be properly grounded to the building/residence AC ground network. All plug-in cards within the computer must be properly installed and grounded to the computer frame per the manufacturers specifications. Ensure proper ventilation. Position the Telephony Gateway so that air flows freely around it and the ventilation holes on the unit are not blocked. Do not mount the Telephony Gateway on surfaces that are sensitive to heat and/or which may be damaged by the heat generated by the modem, its power supply, or other accessories. FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 6 Draft Only Chapter 1: Safety Requirements WARNING Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. RF Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 11.8 inches (30 cm) between the radiator and your body. This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter. Industry Canada Compliance Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. For Mexico The operation of this equipment is subject to the following two conditions: (1) This equipment or device cannot cause harmful interference and (2) this equipment or device must accept any interference, including interference that may cause some unwanted operation of the equipment. European Compliance This product complies with the provision of the Radio and Telecommunication Terminal Equipment (R&TTE) Directive (1999/5/EC), the Electromagnetic Compatibility (EMC) Directive
(2014/30/EU), and the Low Voltage Directive (2014/35/EU). As such, this product bears the CE marking in accordance with the above applicable Directive(s). A copy of the Declaration of Conformity may be obtained from: ARRIS Solutions, UK, 710 Wharfedale Rd, Winnersh, Wokingham RG41 5TP, United Kingdom. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 7 Draft Only Chapter 1: Safety Requirements As indicated by this symbol, disposal of this product or battery is governed by Directive 2002/96/EC of the European Parliament and of the Council on waste electrical and electronic equipment (WEEE). WEEE could potentially prove harmful to the environment; as such, upon disposal of the Telephony Gateway the Directive requires that this product must not be disposed as unsorted municipal waste, but rather collected separately and disposed of in accordance with local WEEE ordinances. This product complies with directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 8 Draft Only Chapter 2 Getting Started Introduction Get ready to experience the Internets express lane! Whether youre checking out streaming media, downloading new software, checking your email, or talking with friends on the phone, the Touchstone TG3482 Telephony Gateway brings it all to you faster and more reliably. All while providing toll quality Voice over IP telephone service and both wired and wireless connectivity. It also provides a Lithium-Ion battery backup to provide continued telephone service during power outages. The Touchstone TG3482 Telephony Gateway provides four Ethernet connections for use as the hub of your home/office Local Area Network (LAN). The TG3482 also provides 802.11a/b/g/n wireless connectivity for enhanced mobility and versatility. In addition, the TG3482 provides for up to two separate lines of telephone service. Installation is simple and your cable company will provide assistance to you for any special requirements. About Your New Telephony Gateway The Touchstone TG3482 Telephony Gateway is DOCSIS compliant with the following features:
Speed: much faster than dialup or ISDN service; up to twenty four times faster than DOCSIS 2.0 cable modems. Convenience: supports Ethernet and 802.11a/b/g/n/ac wireless connections; both can be used simultaneously Flexibility: provides two independent lines of telephone service as well as high speed data Compatibility:
Data services: DOCSIS 3.0 compliant and backward-compatible with DOCSIS 2.0 or 1.1;
supports tiered data services (if offered by your cable company) Telephony services:PacketCable 2.0 compliant Four Ethernet ports for connections to non-wireless devices The TG3482 provides:
Wireless 802.11a/b/g/n/ac connectivity Up to two lines of telephone service DOCSIS 3.0 compliant with Li-Ion backup battery One USB host port (future support for external USB devices) Integrated MoCA 2.0 home networking Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 9 Draft Only What's in the Box Chapter 2: Getting Started Make sure you have the following items before proceeding. Call your cable company for assistance if anything is missing. Telephony Gateway Power Cord Battery (not included with all models) Wireless Connection Configuration Guide Ethernet Cable End User License Agreement Items You Need If you are installing the Telephony Gateway yourself, make sure you have the following items on hand before continuing:
Telephony Gateway package: see What's in the Box (page 10) for a list of items in the package. Coaxial cable (coax): This is a round cable with a connector on each end. It is the same kind of wire used to connect to your television for cable TV. You can buy coax from any electronics retailer and many discount stores; make sure it has connectors on both ends. There are two types of connectors, slip-on and screw-on; the screw-on connectors are best for use with your Telephony Gateway. The coax should be long enough to reach from your Telephony Gateway to the nearest cable outlet. Note: For best performance, use high-quality RG-6 type coax cable and minimize or eliminate splitters between the cable jack and the Data Gateway. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 10 Draft Only Chapter 2: Getting Started Phone Cable: This is a standard phone cable with standard phone connectors (RJ11 type) on both ends. You can buy phone cables from any electronics retailer and many discount stores. Splitter (optional): provides an extra cable connection by splitting a single outlet into two. You may need a splitter if you have a TV already connected to the cable outlet that you want to use. You can buy a splitter from any electronics retailer and most discount stores;
you may also need a short piece of coax cable (with connectors); use it to connect the splitter to the cable outlet and then connect the Telephony Gateway and TV to the splitter. Note: A splitter effectively cuts the signal in half and sends each half to its two outputs. Using several splitters in a line may deteriorate the quality of your television, telephone, and/or internet connection. Information packet: your cable company should furnish you with a packet containing information about your service and how to set it up. Read this information carefully and contact your cable company if you have any questions. Getting Service Before trying to use your new Telephony Gateway, contact your local cable company to establish an Internet account and telephone service. When you call, have the following information ready:
the Telephony Gateway serial number and cable MAC addresses of the unit (printed on the Telephony Gateway) the model number of the Telephony Gateway (printed on the Telephony Gateway) If the Telephony Gateway was provided by your cable company, they already have the required information. In addition, you should ask your cable company the following questions:
Do you have any special system requirements or files that I need to download after I am connected?
When can I start using my Telephony Gateway?
Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 11 Draft Only Chapter 2: Getting Started Do I need a user ID or password to access the Internet or my e-mail?
Will my phone number(s) change?
What new calling features will I have and how do I use them?
System Requirements The Touchstone Telephony Gateway operates with most computers. The following describes requirements for each operating system; see the documentation for your system for details on enabling and configuring networking. To use the Telephony Gateway, you need DOCSIS high-speed Internet service from your cable company. Telephone service requires that the cable company has PacketCable support. Recommended Hardware The following hardware configuration is recommended. Computers not meeting this configuration can still work with the TG3482, but may not be able to make maximum use of TG3482 throughput. CPU: P4, 3GHz or faster RAM: 1GB or greater Hard drive: 7200 RPM or faster Ethernet: Gig-E (1000BaseT) Windows Windows Vista, Windows 7, Windows 8, or Windows 10. A supported Ethernet or wireless LAN connection must be available. Mac OS System 7.5 to Mac OS 9.2 (Open Transport recommended) or Mac OS X. A supported Ethernet or wireless LAN connection must be available. Linux/Unix Hardware drivers, TCP/IP, and DHCP must be enabled in the kernel. A supported Ethernet or wireless LAN connection must be available. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 12 Draft Only Chapter 2: Getting Started About this Manual This manual covers the Touchstone TG3482 Telephony Gateway. The model number is on the label affixed to the Telephony Gateway. 1. Security Label 2. Model Number What about Security?
Having a high-speed, always-on connection to the Internet requires a certain amount of responsibility to other Internet usersincluding the need to maintain a reasonably secure system. While no system is 100% secure, you can use the following tips to enhance your systems security:
Keep the operating system of your computer updated with the latest security patches. Run the system update utility at least weekly. Keep your email program updated with the latest security patches. In addition, avoid opening email containing attachments, or opening files sent through chat rooms, whenever possible. Install a virus checker and keep it updated. Avoid providing web or file-sharing services over your Telephony Gateway. Besides certain vulnerability problems, most cable companies prohibit running servers on consumer-level accounts and may suspend your account for violating your terms of service. Use the cable companys mail servers for sending email. Avoid using proxy software unless you are certain that it is not open for abuse by other Internet users (some are shipped open by default). Criminals can take advantage of open proxies to hide their identity when breaking into other computers or sending spam. If you have an open proxy, your cable company may suspend your account to protect the rest of the network. The TG3482 ships with wireless LAN security set by default (for the same reasons that you should run only secured proxies). See the security label on your product for the factory security settings. If you need to modify the default wireless security settings, see Configuring Your Wireless Connection (page 21). Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 13 Draft Only Ethernet or Wireless?
Chapter 2: Getting Started There are two ways to connect your computer (or other equipment) to the Telephony Gateway. The following will help you decide which is best for you:
Ethernet Ethernet is a standard method of connecting two or more computers into a Local Area Network (LAN). You can use the Ethernet connection if your computer has built-in Ethernet hardware. Note: To connect more than four computers to the TG3482 through the Ethernet ports, you need an Ethernet hub (available at computer retailers). The Telephony Gateway package comes with one 4-foot (1.2m) Ethernet cable (the connectors look like wide telephone connectors); you can purchase more cables if necessary at a computer retailer. If you are connecting the Telephony Gateway directly to a computer, or to an Ethernet hub with a cross-over switch, ask for Category 5e (CAT5e) straight-through cable. CAT5e cable is required for gigabit Ethernet (Gig-E), not regular CAT5 cable. Wireless Wireless access lets you connect additional (wireless-capable) devices to Telephony Gateway. The 802.11 wireless LAN standard allows one or more computers to access the TG3482 using a wireless (radio) signal. These connections are in addition to the connections supported via Ethernet. Note: You can use the wireless connection if your computer has a built-in or aftermarket plug-
in wireless adapter. To learn more about which wireless hardware works best with your computer, see your computer dealer. Both If you have two or more computers, you can use Ethernet for up to four devices and wireless for the others. To connect five or more computers to the Ethernet ports, you will need an Ethernet hub (available at computer retailers.) Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 14 Draft Only Chapter 2: Getting Started Getting Support If you need assistance with your ARRIS product please contact your cable company. For additional technical information and product User Guides please visit the ARRIS Support website at http://www.arris.com/consumers. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 15 Draft Only Chapter 3 Installing and Connecting your Telephony Gateway Before you start, make sure that:
You have contacted your cable company and verified that they provide data and telephone service using standard DOCSIS technology. You have all the Items You Need. Cable, phone, and power outlets are available near the computer. If a cable outlet is not conveniently located, your cable company can install a new one. If you have ordered service, your cable company should configure the Telephony Gateway automatically. You need only follow the instructions in this section to install and connect the Telephony Gateway. CAUTION Risk of equipment damage Only qualified installation technicians should connect the Telephony Gateway to house wiring. Incumbent telephone service must be physically disconnected at the outside interface box before making any connections. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 16 Draft Only Chapter 3: Installing and Connecting your Telephony Gateway Front Panel The front of the Telephony Gateway has the following indicators. 1. WPS Button with indicator light: indicates Wireless Protected Setup (WPS) is active. 2. Power: indicates whether AC power is available to the unit. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 17 Draft Only Chapter 3: Installing and Connecting your Telephony Gateway Rear Panel The rear of the Telephony Gateway has the following connectors and controls. 1. Tel (1 - 2): connectors for phone lines. 2. Ethernet (1 - 2): connectors for use with a computer LAN port. 3. Power: connector for the power cord. 4. Cable: connector for the coaxial cable. 5. Reset button: resets the Telephony Gateway as if you power cycled the unit. Use a pointed non-metallic object to press this button. Selecting an Installation Location There are a number of factors to consider when choosing a location to install your Telephony Gateway:
Is an AC outlet available nearby? For best results, the outlet should not be switched and should be close enough to the Telephony Gateway that extension cords are not required. Is a cable jack available? For best performance, keep the number of splitters between the jack and cable drop to a minimum. Each splitter attenuates (reduces) the signal available to the Telephony Gateway. A large number of splitters can slow down the Internet connection and even affect your telephone service. Can you easily run cables between the Telephony Gateways location and the phones?
Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 18 Draft Only Chapter 3: Installing and Connecting your Telephony Gateway If you are connecting devices to the Ethernet ports, can you easily run cables between the Telephony Gateways location and those devices?
If you want to install the Telephony Gateway on a desktop, is there enough space on either side to keep the vents clear? Blocking the vents may cause overheating. How close are your wireless devices? The Telephony Gateway wireless connection range is typically 100200 feet (30m65m). A number of factors can affect connection range, as described below. Desktop Mounting Instructions Position the Telephony Gateway so that:
it stands vertically on its base (Do not lay it flat on its side.) air flows freely around it the back faces the nearest wall it will not fall to the floor if bumped or moved the ventilation holes on the sides of the unit are not blocked Factors Affecting Wireless Range A number of factors can affect the usable range for wireless connections. Increases range Raising the unit above the devices (for example, installing the Telephony Gateway in the upper floor of a multi-story dwelling) Adding a wireless extender to the network Decreases range Lowering the unit below the devices (for example, installing the Telephony Gateway in a basement) Metal or concrete walls between the Telephony Gateway and other devices Large metal appliances, aquariums, or metal cabinets between the Telephony Gateway and other devices Interference and RF noise (2.4 GHz wireless phones, microwave ovens, or other wireless networks) Note: Note that decreasing the range of your wireless network may be beneficial, as long as the decreased range is sufficient for your needs. By limiting your networks range, you reduce interference with other networks and make it harder for unwanted users to find and connect to your network. Note: Setting the transmit power level to High increases the range. Setting it to Medium or Low decreases the range proportionately. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 19 Draft Only Chapter 3: Installing and Connecting your Telephony Gateway Connecting the Telephony Gateway WARNING Risk of injury or equipment damage Connecting the Telephony Gateway to the homes existing telephone wiring should only be performed by a professional installer. Physical connections to the previous telephone provider must be removed and the wiring must be checked; there must not be any voltage. Cancelation of telephone service is not adequate. Failure to do so may result in loss of service and/or permanent damage to the Telephony Gateway. 1. Connect one end of the coax cable to the cable outlet or splitter, and the other end to the Telephony Gateways Cable connector (3). Tighten the connections by hand, then tighten an additional 1/8 turn with a wrench. Note: For best performance, use high-quality coax cable and minimize or eliminate splitters between the cable jack and the Telephony Gateway. If you are using MoCA for your home network, MoCA filters must be installed on any legacy client devices. Your cable company will install these filters for you. 2. Insert the plug from the power cord into the Power connector on the back of the Telephony Gateway (4), and insert the power cord into a convenient AC outlet. The Power light on the front of the Telephony Gateway lights up, then flashes once. See Troubleshooting (page 31) if the Power light does not turn on. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 20 Draft Only Chapter 3: Installing and Connecting your Telephony Gateway 3. Connect one end of the Ethernet cable to any Ethernet port on the back of the Telephony Gateway (2) and the other end to the Ethernet port on a computer, hub, or broadband router. Note: If you are connecting to a computer, use the Ethernet cable included in the Telephony Gateway package. 4. Connect one end of the telephone cable to any telephone port on the back of the Telephony Gateway (1). Connect the other end to the telephone. Configuring Your Wireless Connection The TG3482 ships with wireless LAN security set by default. See the security label on your product for the factory security settings. Note: You must set up your computer and other client devices to work with the security settings on the TG3482. Refer to the documentation for your client device for instructions on setting security. On most computer systems you only need to select the network name (SSID) device and enter the encryption key. If your computer or client device supports Wi-Fi Alliance WPS (Wireless Protected Setup), activate WPS on your computer or client device and the TG3482 simultaneously to easily set up your system security. 1. Security Label If you need to modify the Telephony Gateways default wireless security settings, or if you want to configure any other wireless LAN settings, refer to the following instructions. Accessing the Configuration Interface Follow these steps to access the configuration interface. You should have already set up the TG3482 as described in Installing and Connecting your Telephony Gateway (page 16). 1. If security has been properly set up on your computer to access the wireless LAN on the TG3482, use the connection utility for your operating system to connect to the wireless LAN using its network name (SSID), as shown on the security label. If you cannot access the wireless LAN, you must first establish a wired Ethernet connection between your computer and the TG3482. In your web browser, open the page http://192.168.0.1/ to access the wireless router setup. 2. 3. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 21 Draft Only Chapter 3: Installing and Connecting your Telephony Gateway The Login screen displays. Note: The default user name is admin. The default password is password, in lower case letters. 4. Enter the user name and password and click the Apply button to log in. The System Basic Setup screen displays. 5. Use the online help information to set configuration parameters as required. Note: Most configuration parameters that you may want to set can be accessed on the System Basic Setup screen, including the security mode and setting a system password. Setting Parental Controls The Parental Control feature allows you to block specified keywords and web sites from being accessed and also to specify trusted computers in the network. Trusted computers are not affected by the parental control settings. Finding the MAC Address of a Computer In order to set up trusted computers you must first determine the MAC address of those computers. Use the operating system of your computer to find its MAC address, as follows:
Windows: from the Start menu, find and select the Control Panel. Double-click Network &
Sharing Center. Then double-click either Wireless Network Connection for a wireless connection, or Local Area Connection for an Ethernet connection. Next click the Details button. The Physical Address line shows the MAC address. MacOS X: open System Preferences and click the Network icon. To find the Ethernet MAC address, select Built-in Ethernet from the Show drop-down, then click the Ethernet tab. The Ethernet ID field shows the MAC address. To find the wireless MAC address, select Airport from the Show drop-down, then click the Airport tab. The Airport ID field shows the MAC address. Linux: open a shell window and type /sbin/ifconfig (and press Enter). The wireless interface is eth1 (unless there is no Ethernet adapter, in which case the interface is eth0). Making Your Parental Control Settings Follow these steps to set up your Parental Controls:
1. Access and log into the wireless configuration interface as explained in Accessing the Configuration Interface (page 21). 2. Click the Firewall tab and then click Parental Controls in the side menu to display the Parental Controls screen. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 22 Draft Only Chapter 3: Installing and Connecting your Telephony Gateway 3. Check the Enable Parental Controls checkbox and click the Apply button. 4. Configure any or all of the following parental controls:
Trusted MAC Addresses:
Enter the MAC addresses of any trusted computers on the network and click the Apply button. You can add two trusted computers. Once added, these trusted computers will not be affected by the parental control settings. For example, you may want the computers of the father and mother to be trusted, while the childrens computers have parental controls in effect. Note: Refer to the Finding the MAC Address of a Computer (page 22) for information on determining the MAC address of your computer. Keyword and Web Site Filtering:
You can add a list of keywords and web sites that you want to block. To add a keyword or web site to the list, click the respective Add button. To delete a keyword or web site from the list, first click its check box and then click the Delete button. Add Keyword Filter Dialog Box Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 23 Draft Only Chapter 3: Installing and Connecting your Telephony Gateway Add Web Site Filter Dialog Box Adding a Keyword or Web Site Filter a. Enter the keyword in the Keyword field or web site URL address in the Web Site field. b. Click the checkboxes for the days you want access blocked, or click the All Week checkbox for all week. c. Set the start time and end time during the specified days (24-hour clock). (0:00 until 0:00 indicates all day, or just click the All Day checkbox.) d. Click the Add Keyword Filter or Add Web Site Filter button respectively. Then click the Apply button. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 24 Draft Only Chapter 4 Configuring Your Ethernet Connection If your computer is equipped with a LAN card providing an Ethernet connection, you may have to configure your computers TCP/IP settings. The steps that follow will guide you through setting your computers TCP/IP settings to work with the Telephony Gateway. Requirements Make sure you have the following before attempting to configure your Ethernet connection:
Computer with Ethernet interface Ethernet cable (supplied) IP address, subnet, gateway, and DNS information for installations not using DHCP How to use this Chapter The following list shows the procedures for modifying the TCP/IP settings on the computer. The procedure is slightly different depending on the operating system that you are using. Please ensure you are using the correct steps for the operating system on your computer. Follow the links below for instructions to configure your Ethernet connection on your operating system. TCP/IP Configuration for Windows Vista (page 25) TCP/IP Configuration for Windows 7, Windows 8, or Windows 10 (page 26) TCP/IP Configuration for Mac OS X (page 26) TCP/IP Configuration for Windows Vista Follow these steps to configure the Ethernet interface on a Windows Vista operating system. 1. Open the Vista Control Panel. 2. Double-click Network and Sharing Center to display the Network and Sharing Center Window. 3. Click Manage network connections. If prompted for a connection, choose Local Area Connection. The Network Connections window displays. 4. Double-click the Local Area Connection to open the Properties window:
Note: If Windows requests permission to continue, click Continue. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 25 Draft Only Chapter 4: Configuring Your Ethernet Connection 5. Double-click Internet Protocol Version 4 (TCP/IPv4) to configure TCP/IPv4. Note: If your cable provider requires TCP/IP version 6, double-click Internet Protocol Version 6 (TCP/IPv6) to configure TCP/IPv6. The TCP/IP properties window for the version you selected displays. 6. For either TCP/IPv4 or TCP/IPv6, select Obtain an IP address automatically and Obtain DNS server address automatically, unless instructed otherwise by your cable provider. 7. Click OK to accept the new settings and close the Properties window. TCP/IP Configuration for Windows 7, Windows 8, or Windows 10 Follow these steps to configure the Ethernet interface on a Windows 7, Windows 8, or Windows 10 operating system. 1. Click the Start menu and type network and sharing into the Search box. 2. Select Network and Sharing Center when it appears. 3. Click Change adapter settings from the left-side menu. 4. Right-click on your local area connection icon and select Properties to open the Properties window. 5. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties to configure TCP/IPv4. Note: If your cable provider requires TCP/IP version 6, select Internet Protocol Version 6
(TCP/IPv6) and click Properties to configure TCP/IPv6. The TCP/IP properties window for the version you selected displays. 6. For either TCP/IPv4 or TCP/IPv6, select Obtain an IP address automatically and Obtain DNS server address automatically, unless instructed otherwise by your cable provider. 7. Click OK to accept the new settings and close the Properties window. Then click Close to back out of the remaining setup screens. TCP/IP Configuration for Mac OS X Follow these steps to configure the Ethernet interface on a Mac OS X operating system. 1. Open System Preferences, either by choosing System Preferences from the Apple menu or by clicking the System Preferences icon in the dock. 2. Click the Network icon. 3. Choose Automatic from the Location drop-down menu, and Built-in Ethernet from the Show menu. 4. Choose the TCP/IP tab, if necessary. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 26 Draft Only Chapter 4: Configuring Your Ethernet Connection If you are using TCP/IPv4, go to step 5. If your cable provider requires TCP/IPv6, go to step 8. 5. Choose Using DHCP from the Configure IPv4 menu. 6. 7. Close the System Properties application. If necessary, click the Renew DHCP Lease button. TCP/IPv4 configuration is completed. If you are using TCP/IPv6, click Configure IPv6 near the bottom of the previous window. 8. 9. Choose Automatically from the Configure IPv6 drop-down menu and click OK. 10. Close the System Properties application. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 27 Draft Only Using the Telephony Gateway Chapter 5 This chapter describes the controls and features available on the Telephony Gateway, and covers basic troubleshooting procedures. Setting up Your Computer to Use the Telephony Gateway (page 28) Indicator Lights for the TG3482 Using the Reset Button Setting up Your Computer to Use the Telephony Gateway Follow the instructions in the information packet supplied by your cable company. Contact your cable company if you need help setting up your computer. Indicator Light for the TG3482 The Telephony Gateway has one LED indicator light (2) to indicate that AC power is available to the unit. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 28 Draft Only Chapter 5: Using the Telephony Gateway Wiring Problems If the Telephony Gateway begins flashing its light for more than 10 seconds, this indicates a problem with the telephone wiring the red and green wires may be shorted (touching), or there may be undesired voltage on the lines. If this pattern persists for more than 10 seconds, disconnect the telephone lines from the Telephony Gateway, then call a wiring technician for assistance. Using the Reset Button Use the Reset button (5), on the back of the Telephony Gateway, to reset the modem and perform initialization as if you power cycled the unit. You may need to reset the Telephony Gateway if you are having problems connecting to the Internet. Using this button will be rare. Use a pointed non-metallic object to press this button. The Reset button is recessed to prevent accidental resets. 1. Tel 2. Ethernet (1-2) 3. Cable 4. Power 5. Reset Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 29 Draft Only Chapter 5: Using the Telephony Gateway Resetting the Router to Factory Defaults To reset the router to factory defaults, press and hold the Reset button on the back of the Telephony Gateway for more than fifteen seconds. This restores the wireless setup configuration and router configuration parameters to the factory defaults. You may need to do this if a misconfiguration has locked out all access. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 30 Draft Only Chapter 6 Troubleshooting The Telephony Gateway is plugged in, but the Power light is Off Check all power connections. Is the power cord plugged in firmly at both ends?
If you plugged the power cord into a power strip, make sure the strip is switched on. Try to plug the power cord into a different outlet. If the outlet is controlled by a wall switch, make sure the switch is on. Finally, check the fuse or circuit breaker panel. I'm not getting on the Internet (all connections) It may take over 30 minutes to establish a connection the first time you power up your Telephony Gateway, especially when many people are online. Always leave your Telephony Gateway plugged into AC power and connected to the cable system. Check the front panel lights:
The Power and Online lights should be on. If the Power light blinks for more than 30 minutes, call your cable company for assistance. Check your cable connections. Connectors should be tight. The coax cable should not be pinched, kinked, or bent sharplyany of these can cause a break or short in the cable (you may have to replace the cable). If you have one or more splitters between the Telephony Gateway and CATV outlet, remove the splitters and connect the Telephony Gateway directly to the outlet. Proceed to the Ethernet or wireless solutions if necessary. I'm not getting on the Internet (Ethernet) If you are using a hub, is the hub turned on?
Are you using the right type of Ethernet cable? Use the supplied cable for direct connection to a computer; use a cross-over cable for connection to a hub. Press the Reset button on the back of the Telephony Gateway. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 31 Draft Only Chapter 6: Troubleshooting A misconfiguration could lock out all access to the Telephony Gateway router. If you think this has happened, see Resetting the Router to Factory Defaults (page 30). I'm not getting on the Internet (Wireless) Check the indicator lights, see Using the Telephony Gateway the Wi-Fi light should be on. Does your connection utility discover your wireless LAN? If you turned off Broadcast SSID you need to manually enter the name of your wireless LAN in the connection utility. Change your security mode to disabled. Enable one of the other security modes as soon as you find the problem. A misconfiguration could lock out all access to the Telephony Gateway router. If you think this has happened, see Resetting the Router to Factory Defaults (page 30). My wireless Internet connection stops working sometimes This is usually caused by interference. Two common sources are 2.4GHz remote telephones and microwave ovens. If you cannot remove the interfering product, try using a different channel or setting Protected Mode. I can get on the Internet, but everything is slow If the Web site you are visiting is very popular, that site may be having trouble servicing all the requests. If other sites download quickly, wait for a few minutes and try again. Usage during peak hours may also affect the connection speed. Other communications on the LAN, or interference with wireless connections, may slow down the connection. I don't have a dial tone when I pick up the phone -
why?
In order for telephone service to be functional on the Telephony Gateway, telephone service must have been purchased from the service provider and configured on your Telephony Gateway. The following steps should help in identifying the source of the problem. 1. If not, check to make sure the Telephony Gateway is plugged in and the outlet has power. Use only the external AC power adapter (if provided) and power cord included with the equipment. If the LED is lit, go to the next step. Is the Power LED lit?
Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 32 Draft Only Chapter 6: Troubleshooting 2. 3. 4. 5. Is the Online LED lit?
If not, check the coax connection at the Telephony Gateway and the wall. Ensure they are connected and tight. If they are and you do not have dial tone, contact your service provider. If the Online LED is lit, go to the next step. Is the Telephone (Tel 1 or Tel 2) LED lit?
If not, phone service has not been set up on that line. Contact your service provider. If it is blinking, there is a phone off hook somewhere in the house. Find that phone and hang it up. If it is lit, go to the next step. Is the phone plugged directly into the Telephony Gateway?
Make sure the phone is plugged into the port on the back of the Telephony Gateway labeled Tel 1 for line 1, and Tel 2 for line 2. If so, try a different phone. Make sure the new phone is a working phone. If a known good phone is used and you still dont have dial tone, try a different phone cable. If a new phone and cable do not restore dial tone, call your service provider. Is the Telephony Gateway plugged into a wall outlet?
If so, unplug the phone connector at the back of the Telephony Gateway and plug in a known working phone. If you now have dial tone, the problem is with the house wiring. Contact your cable company or a qualified wiring technician to correct the house wiring. If you still do not have dial tone, contact your service provider. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 33 Draft Only Glossary A Amp-Hour A measure of battery capacity. For example, a 1.0Ah battery can nominally supply one Ampere of current for one hour. C Category 5e (Cat5e) A high-quality type of cable, used for gigabit Ethernet (1000BaseT) connections. When purchasing Ethernet cables, always look for Category 5e cable. Coaxial cable (coax) A thin wire, used to connect your television and Telephony Gateway to the cable TV system. You can buy coax from any electronics retailer and many discount stores. CPE Customer Premise Equipment. This is the equipment that is plugged in to the Telephony Gateway; typically a computer or hub. Cross-over An Ethernet cable used to connect two hubs (or a hub and a cable modem) together. Also, some Ethernet hubs may have built-in cross-over on one or more ports (which eliminates the need for a cross-over cable). D DHCP Dynamic Host Configuration Protocol. An IP protocol used to provide an IP address and location of services (such as DNS and TFTP) needed by a device connecting to the network. DHCP allows the cable company to configure your computers networking software for you. DNS Domain Name Service (Server). An IP service that associates a domain name
(such as www.example.com) with an IP address. DOCSIS Data Over Cable System Interface Specification. The interoperability standards used for data communications equipment on an HFC network. Downstream In an HFC network, the direction from the head-end to the subscriber. Some older cable documentation may refer to this as the forward path. E EMTA Embedded Multimedia Terminal Adapter. An MTA device that is integrated with a cable modem. Ethernet A standard method of connecting two or more computers into a Local Area Network
(LAN). EuroDOCSIS The European version of DOCSIS. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 34 Draft Only Event An informational message used for monitoring network status. F F-connector The type of connector used on coax cable. There are two common types of F-
connector, slip-on and screw-on. Use coax with screw-on connectors for connecting your Telephony Gateway. Firewall A hardware or software device that prevents unauthorized access to a private network from the Internet. The TG3482 provides a built-in firewall. G Gateway The device, usually a router, that connects devices on a given IP subnet to other IP subnets. H Headend The central office in an HFC network. The headend houses both video and data equipment. In larger cable networks, a master headend often feeds several remote headends to provide distributed services. HTTP HyperText Transfer Protocol. Hub A box with several Ethernet connectors. Ethernet hubs provide a common point of contact for all connected devices. I IP address A number assigned to your computer by your cable company, used to identify your computer to other systems on the Internet. ISDN Integrated Services Digital Network. A digital telephony standard that provides communication speeds about twice as fast as standard dialup. L LAN Local Area Network. A network that allows computers in a single location (such as a building) to communicate with one another. LED Light Emitting Diode. A semi-conductor diode that emits light when current is passed through it. M MAC address A number that uniquely identifies any device connected to a network. Your cable company uses your Telephony Gateways MAC address to authorize access to the Internet. The MAC address is printed on a label on the bottom of your Telephony Gateway. P Protocol A set of rules and formats that determines the communication behavior of network entities at a given layer. Draft Only Proxy A device or program that stands in between a server (for example, a web site) and a client (your browser), providing a way to relieve some of the burden from the server. For example, your cable company may have a web proxy that keeps copies of popular web pages; the proxy can send you those pages instead of fetching them directly from the web site, resulting in faster page loading and less network congestion. R RF Abbreviation for Radio Frequency. Some literature refers to coax as RF cable and the connectors as RF connectors. RJ-11 A standard 2-conductor modular connector, commonly used in North America for connecting telephones. RJ-45 A standard 8-conductor modular connector, commonly used on Ethernet cable. An RJ-45 connector looks like a wide RJ-11 (telephone) connector. S Splitter A small box with three cable connectors:
one input and two outputs. You may need a splitter if you have a TV already connected to the cable outlet that you want to use for your Telephony Gateway. You can buy a splitter from any electronics retailer and most discount stores. SSID Service Set IDentifier. A string of text (up to 32 characters long) that uniquely identifies a wireless LAN. Switched outlet A power outlet that may be turned on and off using a wall switch. Usually intended for lamps. Avoid plugging your computer or Telephony Gateway into a switched outlet to avoid disruptions. T TCP/IP Transmission Control Protocol/Internet Protocol. The protocols used to facilitate communications across one or more connected networks. TDMA Time Division Multiple Access. A method used by DOCSIS-compliant cable modems for sending upstream data with minimal interference. U Upstream The path from a subscriber device to the headend. Some older cable documentation may refer to this as the return path or reverse path. W WEP Wired Equivalent Privacy. A common standard for encrypting data sent over a wireless LAN. Release 34 DRAFT 1.0 July 2016 2016 ARRIS Enterprises LLC. All Rights Reserved. Touchstone TG3482 Telephony Gateway User Guide 36 Draft Only WPA Wi-fi Protected Access. A standard for encrypting data sent over a wireless LAN. WPA offers improved security over WEP. Draft Only Corporate Headquarters ARRIS Suwanee Georgia 30024 USA T: 1-678-473-2000 F: 1-678-473-8470 www.arris.com Draft Only
This product uses the FCC Data API but is not endorsed or certified by the FCC