TR4400 802.11ac Wireless Router User Manual

 

User Guide M o d e l N u m b e r R A C 2 V 1 A 8 0 2 . 1 1 a c W a v e 2 R o u t e r C2V1A Router User Guide 1 Table of Contents 1.1. 1. Overview ............................................................... 5 Introduction .................................................................................................. 5 2. Product Overview ............................................... 6 2.1. About The Router ....................................................................................... 6 2.2. What's in the Box? ..................................................................................... 6 2.3. Items You Need ........................................................................................... 6 2.4. About This Manual ...................................................................................... 7 3. System Requirements ........................................ 8 3.1. Recommended Hardware ........................................................................ 8 3.2. Windows ........................................................................................................ 8 3.3. Mac OS ........................................................................................................... 8 3.4. Linux/Unix ..................................................................................................... 8 3.5. Mobile Devices ............................................................................................. 8 4. Installing the Router ........................................... 9 4.1. Front Panel .................................................................................................... 9 4.2. Rear Panel ................................................................................................... 10 4.3. Selecting an Installation Location ........................................................ 11 4.3.1. Desktop Mounting Instructions ..................................................... 11 4.3.2. Factors Affecting Wireless Range............................................... 12 4.4. Ethernet or Wireless? .............................................................................. 12 4.5. Connecting the Router ........................................................................... 13 4.6. Configuring the Wireless Connection................................................ 14 4.7. Getting Support ........................................................................................ 14 5. Basic Configuration .......................................... 15 5.1. Accessing the Configuration Interface ............................................. 15 5.2. Configuring the Wireless Network ..................................................... 16 5.2.1. Enabling or Disabling the Wireless Network. ......................... 16 5.2.2. Changing the Administrator Password ..................................... 16 5.2.3. Changing the Default Wi-Fi Network Name (SSID) and Password ...............................................................................................17 5.2.4. Configuring Wi-Fi Protected Setup (WPS) .............................. 18 5.2.5. Setting Up the Internet/WAN Connection ............................... 18 RAC2V1A Router User Guide 2 6. Advanced Configuration Options ................ 20 6.1. Configuring DHCP ................................................................................... 20 6.1.1. Configuring DHCP for IPv4 ........................................................... 20 6.1.2. Configuring DHCP for IPv6 ............................................................ 21 6.1.3. Adding and Deleting Reserved DHCP Clients ......................... 21 6.2. Selecting the NAT Mode ........................................................................22 6.3. Setting the Wireless Mode ....................................................................22 6.4. General Firewall Configuration Settings .......................................... 23 6.5. Port Forwarding ....................................................................................... 24 6.6. Configuring DMZ for Gaming or Conferencing Applications ... 25 6.7. Viewing Network System Information ............................................. 26 6.8. Restarting the Router ............................................................................. 26 6.9. Viewing the System Logs ..................................................................... 26 6.10. Setting Up DDNS ..................................................................................... 26 6.10.1. Requirements ......................................................................................27 7. Router Configuration Screen Descriptions 28 7.1. Basic Setup ................................................................................................ 29 7.1.1. Basic Wireless Settings .................................................................. 29 7.1.2. WPS Settings ...................................................................................... 31 7.2. WAN Setup ................................................................................................ 32 7.2.1. Dynamic Configuration Settings (IPv4) ................................... 32 7.2.2. Static IP Connection Type (IPv4) ............................................... 34 7.2.3. DNS Settings ...................................................................................... 35 7.2.4. Dynamic Configuration Settings (IPv6) ................................... 36 7.2.5. Static IP Connection Type (IPv6) ............................................... 37 7.3. LAN Setup .................................................................................................. 39 7.3.1. LAN Settings (IPv4) ........................................................................ 39 7.3.2. LAN Settings (IPv6)......................................................................... 42 7.3.3. Client List ............................................................................................ 44 7.4. Wireless ....................................................................................................... 46 7.4.1. Basic Setup ......................................................................................... 46 7.4.2. Advanced Settings........................................................................... 50 7.4.3. Associated Stats ............................................................................... 53 7.4.4. Airtime Fairness ................................................................................ 54 7.4.5. QoS Classification ............................................................................ 56 7.4.6. Log ......................................................................................................... 58 7.5. Firewall ........................................................................................................ 59 7.5.1. Firewall Settings ............................................................................... 59 RAC2V1A Router User Guide 3 7.5.2. Port Forwarding ................................................................................ 60 7.5.3. Port Triggers ....................................................................................... 61 7.5.4. DMZ ....................................................................................................... 62 7.5.5. WAN Ping Blocking ......................................................................... 64 7.5.6. Application Layer Gateway Settings ......................................... 64 7.5.7. MAC Filter ........................................................................................... 65 7.5.8. Parental Controls .............................................................................. 66 7.5.9. IPv6 Client Filter ............................................................................... 73 7.6. USB ............................................................................................................... 74 7.6.1. USB Status .......................................................................................... 74 7.6.2. File Sharing ......................................................................................... 75 7.6.3. Media Sharing ..................................................................................... 77 7.6.4. USB Access Control ........................................................................ 78 7.7. Utilities ......................................................................................................... 79 7.7.1. System Information ......................................................................... 79 7.7.2. Restart Router .................................................................................... 81 7.7.3. Factory Defaults ............................................................................... 82 7.7.4. System Settings ................................................................................ 83 7.7.5. System Logs ....................................................................................... 84 7.7.6. DDNS .................................................................................................... 85 7.7.7. Blocked Device ................................................................................. 86 7.7.8. QoS ........................................................................................................ 87 8. Troubleshooting ............................................... 89 8.1. The router is plugged in, but the light is off ................................... 89 8.2. I'm not getting on the Internet (all connections) ......................... 89 8.3. I'm not getting on the Internet (Ethernet) ...................................... 89 8.4. I'm not getting on the Internet (Wireless) ...................................... 89 8.5. My wireless Internet connection stops working sometimes .... 90 8.6. I can get on the Internet, but everything is slow .......................... 90 9. Safety Requirements ........................................ 91 9.1.1. Federal Communication Commission Interference Statement ............................................................................................. 91 RAC2V1A Router User Guide 4 Overview Introduction Get ready to experience the Internets express lane! Whether youre checking out streaming media, downloading new software, or checking your email, the RAC2V1A router brings it all to you faster and more reliably. The RAC2V1A router provides four Ethernet connections for use as the hub of your home/office Local Area Network (LAN). The RAC2V1A also provides 802.11a/b/g/n/ac wireless connectivity for enhanced mobility and versatility. Installation is simple, and Spectrum will provide assistance to you for any special requirements. RAC2V1A Router User Guide 5 Product Overview About The Router The RAC2V1A router is a dual-band 802.11ac router that allows users to connect to the Internet through a separate modem. The RAC2V1A router has the following features:

Remote management capability: allows Spectrum to make changes to the router's configuration Convenience: supports Ethernet and 802.11a/b/g/n/ac wireless connections; both wired and wireless connections can be used simultaneously Four Gigabit Ethernet ports for connections to non-wireless devices A USB 3.0 host port What's in the Box?

Make sure you have the following items before proceeding. Call Spectrum for assistance if anything is missing. Router Power Supply Spectrum Quick Start Guide Two Stickers with Wi-Fi Network Name and Password Ethernet Cable Safety Insert/License Agreement Items You Need Make sure you have the following items on hand before continuing:

Router package: see What's in the Box? (page 7) for a list of items in the package. Ethernet Cable: In addition to the Ethernet cable provided, you may need an additional Ethernet cable if you want to connect to wired clients. This is a standard CAT5e Ethernet cable with RJ45 type connectors on both ends. You can buy Ethernet cables from any electronics retailer and many discount stores. Spectrum Quick Start Guide: This guide contains information about your service and how to set it up. Read this information carefully and contact Spectrum if you have any questions. RAC2V1A Router User Guide 6 Product Overview About This Manual This manual covers the RAC2V1A router. You can find product information on the security label affixed to the back of the router. 1. MAC address 2. Wi-Fi Network Name (SSID). The XX here represents the last octet of the MAC address. 3. Wi-Fi Password RAC2V1A Router User Guide 7 System Requirements The router operates with most computers and wireless devices. The following describes requirements for each operating system; see the documentation for your system for details on enabling and configuring networking. To use the router, you need high-speed Internet service from Spectrum. Recommended Hardware The following hardware configuration is recommended. Computers not meeting this configuration can still work with the router, but may not be able to make maximum use of available throughput. CPU: P4, 3 GHz or faster. RAM: 1 GB or greater. Ethernet: Gig-E (1000Base-T). Wi-Fi: 802.11a, b, g, n, or ac compliant Wi-Fi equipment. Windows Windows 7, Windows 8, or Windows 10. A supported Ethernet or wireless LAN connection must be available. Mac OS System 7.5 to Mac OS 9.2 (Open Transport recommended), or OS X. A supported Ethernet or wireless LAN connection must be available. Linux/Unix Hardware drivers, TCP/IP and DHCP must be enabled in the kernel. A supported Ethernet or wireless LAN connection must be available. Mobile Devices Android OS or iOS. RAC2V1A Router User Guide 8 Installing the Router Before you start, make sure that:

You have all the Items You Need (page 6). The modem and power outlets are available nearby. Front Panel The router has one light, located on the front right corner. The light on the front of the router indicates the operating status. A soft pulsing blue light on the front panel indicates normal operation. A pulsing light that alternates blue and red indicates that the router is updating firmware. RAC2V1A Router User Guide 9 A flashing red light indicates that the router is establishing the Installing the Router internet connection. A solid red light indicates that the device was not able to achieve a normal operating state. Rear Panel The rear of the router has the following connectors and controls:

RAC2V1A Router User Guide 10 Installing the Router 1. Reset button: resets the router as if you power cycled the unit. Use a pointed non-metallic object to press this button and hold it for more than one second but less than five seconds. Note: If you hold the Reset button for more than five seconds, the router will be reset to the factory default settings and will restart. Do not perform a factory reset unless you expressly guided to do so by Spectrum customer service. 2. WPS Button: begins associating the router with a wireless device. 3. Ethernet (1 - 4): connectors for use with a computer LAN port or another Ethernet-connected device. 4. Internet: connector to the Spectrum modem. 5. USB: USB host connector for use with external USB devices. 6. Power: connector for the power cord. Selecting an Installation Location There are a number of factors to consider when choosing a location to install the router:

Is an AC outlet available nearby? For best results, the outlet should not be switched and should be close enough to the router that extension cords are not required. Is the modem nearby? Can you easily run cables between the routers location and the modem?

If you are connecting devices to the Ethernet ports, can you easily run cables between the routers location and those devices?

If you want to install the router on a desktop, is there enough space on either side to keep the vents clear? Blocking the vents may cause overheating. How close are the wireless devices? In general, the router should be located centrally within the premises, as close as possible to the location where users will want to access the wireless connection. The router wireless connection range is typically 100200 feet (30m 65m) for 2.4 GHz signals and less for 5 GHz signals. A number of factors can affect connection range, as described below. Desktop Mounting Instructions Position the router so that:

Air flows freely around it RAC2V1A Router User Guide 11 The back faces the nearest wall The sides of the unit are not blocked. Factors Affecting Wireless Range It will not fall to the floor if bumped or moved Installing the Router A number of factors can affect the usable range for wireless connections. Increases range Locating the unit centrally Creating as much "line-of-sight" as possible with client devices Decreases range Metal or concrete walls between the router and other client devices Large metal appliances, aquariums, or metal cabinets between the router and other client devices Interference and RF noise (2.4 GHz wireless phones, microwave ovens, wireless speaker/receiver systems, or other wireless networks) Placing the router in a cabinet or other enclosed space Placing the router next to a desktop computer Notes:

It may be acceptable to decrease the range of the wireless network, as long as the decreased range is sufficient for your needs. By limiting the networks range, you reduce interference with other networks and make it harder for unwanted users to find and connect to the network. Setting the transmit power level to High increases the range. Setting it to Medium or Low decreases the range. Medium or Low may be more appropriate for high-density residential locations. Ethernet or Wireless?

There are two ways to connect the computer (or other equipment) to the router. The following will help you decide which is best for you:

Ethernet Ethernet is a standard method of connecting two or more computers into a Local Area Network (LAN). You can use the Ethernet connection RAC2V1A Router User Guide 12 Installing the Router if the client device has built-in Ethernet hardware. The router provides support for up to four such connected devices. Note: To connect more than four client devices to the router through the Ethernet ports, you need an Ethernet switch (available at computer retailers). The router includes one 3-foot (.9m) Ethernet cable. The enclosed Ethernet cable is yellow to match the Internet port on the back of the router, because this cable is primarily intended to connect the router to the Spectrum modem. You can purchase more cables if necessary at a computer retailer. If you are connecting the router directly to a computer, or to an Ethernet switch with a cross-over switch, ask for Category 5e (CAT5e) straight-through cable. CAT5e cable is required for gigabit Ethernet (Gig-E), not regular CAT5 cable. Wireless Wireless access lets you connect additional (wireless-capable) devices to the router. The 802.11 wireless LAN standard allows one or more computers to access the router using a wireless (radio) signal. These connections are in addition to the connections supported via Ethernet. Both If you have two or more clients, you can use Ethernet for up to four devices and wireless for the others. Connecting the Router 1. Unplug the power to turn off the modem. 2. Connect one end of the Ethernet cable (included) to the modem, and the other end to the Internet port on the router. 3. Reconnect the plug on the modem to turn the modem back on. Wait approximately 2 minutes to allow the modem to fully power up. RAC2V1A Router User Guide 13 4. Connect the power adapter (included) to the power connector on the back of the router, and then connect the power adapter to an available AC outlet. Wait until the light on the front panel of the router turns blue and begins to pulse. Installing the Router 5. To manage the setup of the router, you can use a second Ethernet cable (not provided) to connect a computer to an available LAN port on the router, or you can connect wirelessly by using the preset wireless security settings printed on the security label located on the back of the router. 6. Open a browser on the computer to access the management interface of the router. If the webpage does not display correctly, try another browser. See Accessing the Configuration Interface (page 15) for more information. Configuring the Wireless Connection The router ships with a secure Wi-Fi network name (SSID) that is unique for every device. By default, the router is set to the most current wireless security setting, WPA2, to provide maximum protection for Wi-Fi devices connected to the router. Wi-Fi network information is located on the label on the back of the router. You can sign in to the router and configure additional wireless settings. See Configuring the Wireless Network (page 16) for complete instructions on configuring the wireless connection. Getting Support Please contact Spectrum if you need assistance. RAC2V1A Router User Guide 14 Basic Configuration The router ships with a basic factory default configuration that should allow you to immediately access the Internet after installing the hardware according to the instructions in this guide. If you need to modify the router's default basic settings, or if you want to configure advanced settings, refer to the appropriate instructions in this document. Wireless LAN Default Security Setting: The router ships with wireless LAN security set by default. See the security label on the product for the factory security settings: Wi-Fi network name (SSID) and Wi-Fi password. If you need to modify the routers default wireless security settings, or if you want to configure any other settings, refer to the appropriate instructions in this document. Note: You may set up the computer and other client devices to work with the security settings on the router. Most client devices support the WPA2 default security standard in the router. Refer to the documentation for the client device for instructions on setting security. If the computer or client device supports Wi-Fi Alliance WPS (Wireless Protected Setup), activate WPS on the computer or client device and the router simultaneously to easily set up the Wi-Fi security. Accessing the Configuration Interface Perform the following steps to access the configuration interface. 1. If security has been properly set up on the computer to access the wireless LAN on the router, use the connection utility for the operating system to connect to the wireless LAN using its Wi-Fi network name (SSID), as shown on the security label. Note: If you cannot access the wireless LAN, you must first establish a wired Ethernet connection between the computer and the router. 2. In the web browser, open the page http://192.168.1.1/ to access the router setup. The sign-in screen for the router displays. RAC2V1A Router User Guide 15 3. Enter the user name and password, and click Apply to sign in. These Basic Configuration default sign-in credentials appear on the label on the back of the router. The Basic Wireless Settings screen displays. Note: The default user name and the default password are both admin. Both are in lower case letters. 4. Set basic setup configuration parameters as required for the system. Note: Most configuration parameters that you may want to set can be accessed on the Basic Wireless Settings screen or on the LAN Setup or Wireless tabs. Configuring the Wireless Network Perform the following steps to make the basic configuration settings for the wireless network. Enabling or Disabling the Wireless Network. By default, the router is shipped with a default Wi-Fi network name and Wi-Fi password for both 2.4 GHz and 5 GHz, as well as WPA2 security. You can find this network name and password on the label on the back of your router. Perform the following steps to disable or re-enable the wireless network. 1. Access and sign in to the configuration interface. 2. Click the Basic Setup tab. 3. Click the Enable SSID checkbox in either the Wireless 2.4 GHz section or the Wireless 5 GHz section to enable wireless networking for that frequency. 4. Click Apply. Changing the Administrator Password You should change the administrator password to something other than the default password so that unauthorized users cannot access your configuration interface. Note: When you first set up your router, the default user name and the default password are both admin. Both are in lower case letters. Perform the following steps to change the administrator password. 1. Access and sign in to the configuration interface. See Accessing the Configuration Interface (page 15) for more information. 2. Click the Utilities tab. RAC2V1A Router User Guide 16 Basic Configuration 3. Click System Settings in the side menu. 4. Enter the current administrator password in the Current Password field. 5. Enter the new administrator password in both the New Password and Confirm New Password fields. Note: Administrator passwords are case-sensitive and must be between 8-12 characters long. You can use any alphanumeric characters (digits 0-9 and letters A-Z, either upper- or lower-case) and printable special characters (such as $, !, ?, &, #, @ and others). 6. Click Apply. 7. Record your new administrator password here: __________________ Changing the Default Wi-Fi Network Name (SSID) and Password Perform the following steps to change the 2.4 GHz and/or 5 GHz Wi-Fi network name and password. 1. Access and sign in to the configuration interface. 2. Click the Basic Setup tab. 3. On the Basic Wireless Settings screen, enter a unique user-friendly name to identify the Wi-Fi network in the Wi-Fi Network Name

(SSID) field under either Wireless 2.4 GHz or Wireless 5 GHz. Note: This name is also referred to as the Service Set Identifier

(SSID). The name can be up to 32 characters long. Do not duplicate any other Wi-Fi network names (SSIDs that may be operating in the area. 4. Enter a new password in the Password (Network Key) field. Valid characters are the numbers 0 to 9, the letters a through z and A through Z and printable characters (such as $, !, ?, &, #, @ and others). 5. Click Apply at the bottom of the screen. 6. Record the new network names and passwords here:

2.4 GHz Wi-Fi Network name (SSID): __________________________ 2.4 GHz Password: ______________________________ 5 GHz Wi-Fi Network name (SSID): ___________________________ 5 GHz Password: _______________________________ RAC2V1A Router User Guide 17 Basic Configuration Configuring Wi-Fi Protected Setup (WPS) WPS is a standard method for easily configuring a secure connection between the router and computers or other wireless devices (known as enrollees) that support WPS. When WPS is enabled you can attach other wireless devices by pressing the WPS buttons on the device (if equipped) and on the router, or by entering the enrollees PIN and then clicking the Start WPS Association icon. Perform the following steps to enable the wireless network. 1. Access and sign in to the configuration interface. 2. Click the Basic Setup tab. 3. Click WPS Settings in the side menu. 4. In the appropriate section (2.4 GHz or 5 GHz), click the Wi-Fi Protected Setup (WPS) Enable checkbox and click Apply to enable WPS on the system. 5. a. If the client device has a WPS button, press the WPS buttons on the client device and on the router simultaneously to start the WPS association. Note: If you prefer, you can click Start PBC on the WPS Settings screen instead of pressing the WPS button on the back of the router.) b. If the client device has a PIN number, enter the enrollees PIN in the Enrollee PIN Code field, and then click Enroll. Enter the routers PIN code in the Device PIN Code field if requested during connection. 6. If the connection is successful, then the device will connect to the router. If it does not connect for some reason, then you should start the association process over. Setting Up the Internet/WAN Connection A Dynamic or DHCP (Dynamic Host Configuration Protocol) connection is the most commonly used WAN connection type. Note: Do not change this setting unless Spectrum tells you to use another connection type. Perform the following steps to change the connection type. RAC2V1A Router User Guide 18 Basic Configuration 1. Access and sign in to the configuration interface. 2. Click the WAN Setup tab. 3. Click Dynamic (IPv4), Static (IPv4), Dynamic (IPv6), or Static

(IPv6) in the side menu to display the appropriate screen for configuring that type of WAN connection. 4. Set the required configuration parameters for the connection type you selected as provided by Spectrum. Note: Refer to WAN Setup in Router Configuration Screen Descriptions (page 28) for specific instructions on setting the various connection type configuration parameters. 5. Click Apply at the bottom of the screen. RAC2V1A Router User Guide 19 Advanced Configuration Options This section explains how to use the most common advanced configuration options for the router in the following areas:

LAN Setup Wireless Setup Firewall Utilities Note: Refer to Router Configuration Screen Descriptions (page 28) for additional advanced configuration options. Configuring DHCP DHCP (Dynamic Host Protocol Configuration) is enabled by default on the router, which allows the router to act as a DHCP server and automatically assign an IP address to each device on the network. DHCP is a set of rules used by devices such as a computer, router, or network adapter to allow the device to request and obtain an IP address from a server, which maintains a list of addresses available for use. The DHCP server ensures that all IP addresses are unique, e.g., no IP address is assigned to a second device while the first device's assignment is valid

(its lease has not expired). Without DHCP, the IP addresses must be entered manually at each computer or device and a new IP address must be entered each time it moves to a new location on the network. Configuring DHCP for IPv4 Perform the following steps to configure DHCP for IPv4. 1. Access and sign in to the configuration interface. 2. Click the LAN Setup tab. 3. Click LAN Settings (IPv4) in the side menu to display the LAN Settings screen. 4. Click the Enable DHCP Server checkbox under DHCP Server Settings. RAC2V1A Router User Guide 20 Advanced Configuration Options 5. Enter the Start IP Address and End IP Address for the range of IP addresses that the DHCP Server running on the route will be allowed to assign to a network device. 6. In the Lease Time field, select the time before the assigned IP address will expire. (After the lease time is up, the user is automatically assigned a new dynamic IP address.) Note: Refer to LAN Setup (page 39) for specific instructions on setting the various DHCP configuration parameters. 7. Click Apply at the bottom of the screen. Configuring DHCP for IPv6 Perform the following steps to configure DHCP for IPv6. 1. Access and sign in to the configuration interface. 2. Click the LAN Setup tab. 3. Click LAN Settings (IPv6) in the side menu to display the LAN Settings screen. 4. Click the Enable checkbox under LAN Settings (IPv6). 5. Enter the Start IP Address and End IP Address for the range of IP addresses that the DHCP Server running on the route will be allowed to assign to a network device. 6. In the Lease Time field, select the time before the assigned IP address will expire. (After the lease time is up, the user is automatically assigned a new dynamic IP address.) Note: Refer to LAN Setup (page 39) for specific instructions on setting the various DHCP configuration parameters. 7. Click Apply at the bottom of the screen. Adding and Deleting Reserved DHCP Clients The Client List screen shows the IP address, host name and MAC address of each computer that is connected to the network. If a computer does not have a specified host name, then the host name field will be blank. Perform the following steps to configure the DHCP Clients. 1. Access and sign in to the configuration interface. 2. Click the LAN Setup tab. RAC2V1A Router User Guide 21 3. Click Client List in the side menu to display the Client List screen. 4. Click Add to add a reserved IP client. Select an existing DHCP client Advanced Configuration Options and then click Delete to delete the reserved IP for the client. Click Refresh to update the Attached Client List. Selecting the NAT Mode NAT (Network Address Translation) allows the router to manipulate IP addresses so that just one single IP address can represent an entire group of computers on the network and let them all communicate with the Internet. This conserves IP addresses and is necessary in IPv4 since there are a limited number of available IP addresses for use. (This limitation does not affect the IPv6 address space.) Perform the following steps to select the NAT Mode. 1. Access and sign in to the configuration interface. 2. Click the LAN Setup tab. 3. Click LAN Settings (IPv4) in the side menu to display the LAN Settings screen. 4. Select the NAT Mode from the NAT Mode field drop-down list. The optional modes are:

o Bridged: Data will pass through the router directly without any routing and without NAT. o RoutedWithNAT: Data will be routed by the device and all the outgoing packets will be NATed. o RoutedWithoutNAT: Data will be routed by the device but all the outgoing packets will not be NATed. 5. Click Apply at the bottom of the screen. Note: A dialog box prompts you to restart the router. Click OK to restart. Setting the Wireless Mode You can set the wireless mode to optimize performance based on the type of network adapters being used by the client devices (for example, 820.11g, 802.11n or 802.11ac). Select the proper mode to support all of the wireless devices that will connect to the router. Perform the following steps to set the wireless mode. 1. Access and sign in to the configuration interface. 2. Click the Wireless tab. RAC2V1A Router User Guide 22 Advanced Configuration Options 3. Click Basic Setup in the side menu to display the Basic Settings screen. 4. Under Wireless 2.4 GHz or Wireless 5 GHz, select the proper mode from the Wireless Mode drop-down list. The following options are available:

2.4 GHz Options:

o 802.11g o 802.11g+n 5 GHz Options:

o 802.11n o 802.11n&802.11ac o 802.11ac Note: Mixed modes will be able operate in more than one mode, depending on the capabilities of the connected device. 5. Click Apply at the bottom of the screen. Note: If you have both 802.11a and 802.11b running on your network, then clients that are capable of faster wireless modes will be slowed down. General Firewall Configuration Settings The router is equipped with a firewall that will protect your network from a wide array of common Denial of Service (DoS) attacks, including Ping of Death (PoD) attacks. The firewall is enabled by default, but you can choose to disable it. Turning off the firewall protection will not leave the network completely vulnerable to hacker attacks, but it is recommended that you enable the firewall whenever possible. Perform the following steps if you have disabled the firewall and want to enable it again. 1. Access and sign in to the configuration interface. 2. Click the Firewall tab. 3. Click Firewall Settings in the side menu to display the Firewall Settings screen. 4. Check the Enable Firewall checkbox to enable the firewall on the network. 5. Click Apply at the bottom of the screen. RAC2V1A Router User Guide 23 6. Click WAN Ping Blocking in the side menu to display the WAN Ping Advanced Configuration Options Blocking screen. 7. Check the Block ICMP Ping Enable checkbox to protect against PoD attacks. 8. Click Apply at the bottom of the screen. Port Forwarding The port forwarding function forwards inbound traffic from the Internet to a specified single device on your network. Examples include allowing access to a web server on your network, peer-to-peer file sharing, applications that allow remote access to a specified computer, some gaming and videoconferencing applications and others. If you have a server in the network that you want to make available to the Internet, you can set up port forwarding. The firewall passes requests from the Internet to the designated computer on the network. This function works by allowing you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through the router to the internal network. Perform the following steps to set up port forwarding. 1. Access and sign in to the configuration interface. 2. Click the Firewall tab. 3. Click Port Forwarding in the side menu to display the Port Forwarding screen. 4. Select the type of server that you want to add from the Service List drop-down box. 5. Click Add 6. If necessary, adjust the following parameters. Enable Enable forwarding for this port. Description Enter a name for the port you want to forward. Inbound Port Enter the inbound port range for the port you want to forward. It should be the same range as the local port. Type Sets the format for the port. Options are TCP, UDP, or BOTH. RAC2V1A Router User Guide 24 Advanced Configuration Options Private IP Address Enter the IP address of the machine on the LAN where you want the connections to go. Private Port Enter the private port range for the port you want to forward. It should be the same range as the inbound port. 7. Click Apply to save your settings. Note: To stop forwarding a port, uncheck Enable for the forwarding rule, and then click Apply. To completely remove a port forwarding rule, choose the entry, choose the entry ID in the drop-down list and click Clear, then click OK and Apply. Configuring DMZ for Gaming or Conferencing Applications The DMZ feature allows you to specify one computer on the network to be placed outside of the NAT firewall. This may be necessary if the NAT feature is causing problems with an application such as a game or video conferencing application. Use this feature only on a temporary basis. The computer in the DMZ is not protected from hacker attacks. Perform the following steps to put a computer in the DMZ. 1. Access and sign in to the configuration interface. 2. Click the Firewall tab. 3. Click DMZ in the side menu to display the DMZ screen. 4. Enter the following parameters. Enable Click this checkbox to enable DMZ on the network. Static IP Displays the routers WAN IP address. Private IP Enter the IP address of the computer to be placed in the DMZ. We recommend that you choose a reserved, routable IP address. After placing the computer in the DMZ, all ports on the computer are open to the Internet and not protected. 5. Click Apply at the bottom of the screen. Note: To remove the computer from the DMZ, uncheck the Enable checkbox and then click Apply. RAC2V1A Router User Guide 25 Viewing Network System Information You can view status and system information for the network on the System Information screen. Advanced Configuration Options Perform the following steps to view system status information. 1. Access and sign in to the configuration interface. 2. Click the Utilities tab. 3. Click System Information in the side menu to display the System Information screen. Note: Refer to System Information (page 79) for an explanation of the various status information parameters. Restarting the Router It may be necessary to restart (reset) the router if it stops working properly. This is the equivalent of unplugging power from the router and plugging power back in. Restarting the router will not delete any of the configuration settings. Perform the following steps to restart the router. 1. Access and sign in to the configuration interface. 2. Click the Utilities tab. 3. Click Restart Router in the side menu to display the Restart Router screen. 4. Click the Restart Router button to restart the router. Viewing the System Logs The System Logs screen displays the system logs. Perform the following steps to configure the system logs. 1. Access and sign in to the configuration interface. 2. Click the Utilities tab. 3. Click System Log in the side menu to display the System Logs. When viewing the logs, click Refresh to update the list. Setting Up DDNS DDNS (Dynamic DNS) allows you to provide Internet users with a fixed domain name (instead of an IP address which may periodically change). This allows various locations on the Internet to access the gateway and RAC2V1A Router User Guide 26 Advanced Configuration Options the applications that are set up in the gateway's port forwarding table without knowing your current IP address. Requirements In order to use DDNS you must first create an account with a DDNS provider. The DDNS provider maps your chosen domain name to your IP address. Once the account is established, perform the following steps to enable DDNS. 1. Access and sign in to the configuration interface. 2. Click the Utilities tab. 3. Click DDNS in the side menu to display the DDNS configuration screen. 4. Click the DDNS Enable checkbox. Note: Refer to DDNS (page 85) for specific instructions on setting the various DDNS configuration parameters. 5. After setting the necessary configuration parameters, click Apply at the bottom of the screen. RAC2V1A Router User Guide 27 Router Configuration Screen Descriptions This section provides an overview of the graphical user interface (GUI) router setup screens. Each of the following tabs in the GUI and their individual sub-menus and configuration parameters are explained in detail:

Basic Setup WAN Setup LAN Setup Wireless Firewall USB Utilities RAC2V1A Router User Guide 28 Basic Setup Basic Wireless Settings Router Configuration Screen Descriptions While the system has many configuration options, the options on this Basic Setup page are those required by most users. Click the tabs to access the other configuration pages to set advanced options. Hover the mouse pointer over the question mark icon next to an option to view a description of that option. For changes to take effect, you must click Apply. Wireless 2.4 GHz/Wireless 5 GHz Enable SSID Wi-Fi Network Name (SSID) Click this checkbox to enable the wireless network on the system. Enter a user-friendly name to identify the wireless network. This name is also referred to as the Service Set Identifier (SSID). The name can be up to 32 characters long. RAC2V1A Router User Guide 29 Wi-Fi Password Router Configuration Screen Descriptions Sets the Wi-Fi password. Use a Wi-Fi password that will not be easy to guess. Wi-Fi passwords are case-

sensitive. Valid characters are the numbers 0 to 9, the letters a through z and A through Z and printable special characters (such as $, !, ?, &, #, @

and others). You must click Apply to save the new Wi-Fi password. RAC2V1A Router User Guide 30 WPS Settings Router Configuration Screen Descriptions Wi-Fi Protected Setup (WPS) is the industry standard method to simplify the security setup and management of Wi-Fi networks. You can now easily set up and connect to a WPS-enabled 802.11 network with WPS-certified devices using either a Personal Information Number (PIN) or the Push Button Configuration (PBC) method. Legacy devices without WPS can be added to the network using the traditional manual configuration method. WPS Enable/Disable Wireless 2.4 GHz/ Wireless 5 GHz Click the frequency for which you want to enable WPS. WPS Enable Click this checkbox to enable WPS on the system. RAC2V1A Router User Guide 31 Router Configuration Screen Descriptions WPS is a standard method for easily configuring a secure connection between the router and computers or other wireless devices (known as enrollees) that support WPS. When WPS is enabled, you can attach other wireless devices by pressing the WPS buttons on the device (if equipped) and on the router, or by entering the enrollees PIN and then clicking Enroll. PIN Method Enrollee PIN Code If the client device has a WPS PIN number, enter it here, then click Enroll. Device PIN Code Enter this code on the computer if requested during connection. PBC Method Start PBC Click to start the PBC connection process. This is equivalent to pressing the WPS button on the back of the router. WAN Setup Dynamic Configuration Settings (IPv4) RAC2V1A Router User Guide 32 Router Configuration Screen Descriptions A dynamic connection type is the most common type of connection. The router gets its IP address from a Spectrum DHCP server. If you are not sure of the connection type, use a dynamic connection. For changes to take effect, you must click Apply. Unless Spectrum directs you to do choose a Static address, you should choose a dynamic address. Note: You can use static (manual) IP addresses in addition to the DHCP server, but any static addresses must be outside the range of the DHCP pool to avoid duplicate IP addresses. Also, the static WAN IP address must be routable by northern-bound routers. DHCP Enable DHCP Click this checkbox to enable a DHCP connection for the system. Host Name Use this field to enter a host name for the router. MTU Maximum Transmission Unit. This is a measure of Internet packet size, in bytes, that can be forwarded to the network. You should not change this field unless specifically directed to do so by Charter. RAC2V1A Router User Guide 33 Static IP Connection Type (IPv4) Router Configuration Screen Descriptions A static IP address connection type is less common than others and uses a permanent IP address to connect to the Internet. If Spectrum provides an IP address that never changes, then use this option. For changes to take effect, you must click Apply. Static IP Settings Enable Static IP IP Address Subnet Mask Click this checkbox to enable a static IP address connection for the system. Enter the IP address assigned by Spectrum for static IP operation. Enter the subnet mask assigned for the device by Spectrum for static IP operation. Gateway Address Enter the gateway address assigned for the device by Spectrum for static IP operation. RAC2V1A Router User Guide 34 MTU Click here to enter your DNS Settings DNS Settings Router Configuration Screen Descriptions Maximum Transmission Unit. This is a measure of Internet packet size, in bytes, that can be forwarded to the network. You should not change this field unless specifically directed to do so by Charter. If Spectrum gave you specific DNS settings, click here to go to the DNS Settings screen to enter those settings. Use this screen to change your DNS settings, if necessary. Note: In most cases, you will not need to change your DNS settings. DNS Settings Automatic from ISP Click this checkbox if the router should automatically get its DNS settings from Spectrum. Primary DNS Server IP Secondary DNS Server IP Enter the IP address of the primary DNS server.

(This field is only available if Automatic from ISP is not checked.) Enter the IP address of the secondary DNS server.

(This field is only available if Automatic from ISP is not checked.) RAC2V1A Router User Guide 35 Dynamic Configuration Settings (IPv6) Router Configuration Screen Descriptions This screen enables a DHCPv6 configured IPv6 stack. A dynamic connection type is the most common type of connection. The router gets its IP address from a Spectrum DHCP server. Unless Spectrum directs you to do choose a Static address, you should choose a dynamic address. For changes to take effect, you must click Apply. Dynamic Configuration (IPv6) Enable DHCP

(IPv6) IP Address v6 Clear this checkbox if you want to disable a DHCP

(IPv6) connection for the system. This field displays the IPv6 address automatically assigned by Spectrum. An IPv6 address has eight groups of four hexadecimal digits (0-9, a-f). The groups are separated by colons, for example, 2001:0db8:85a3:0000:0000:8a2e:0370:7334. A double colon (::) is shorthand for an address of all zeros. RAC2V1A Router User Guide 36 Router Configuration Screen Descriptions The prefix length appears at the end of the IPv6 address, following a slash. Delegated Prefix This field displays the assigned IPv6 prefix to be used by addresses allocated in the local network. Delegated Prefix Length This field displays the assigned IPv6 prefix length. IPv6 Gateway Address Static IP Connection Type (IPv6) This field displays the gateway address. This screen enables a statically configured IPv6 address. A static IP address connection type is less common than others and uses a permanent IPv6 address to connect to the Internet. If Spectrum provides an IP address that never changes, then use this option. For changes to take effect, you must click Apply. RAC2V1A Router User Guide 37 Static IP Settings (IPv6) Router Configuration Screen Descriptions Enable Static IPv6 IP Address v6 Prefix Length

(IPv6) IPv6 Gateway Address Primary DNS Server (IPv6) Click this checkbox to enable a static IPv6 address connection for the system. Enter the IPv6 address assigned to you by Spectrum or static IP operation. An IPv6 address has eight groups of four hexadecimal digits (0-9, a-f). The groups are separated by colons, for example, 2001:0db8:85a3:0000:0000:8a2e:0370:7334. A double colon (::) is shorthand for an address of all zeros. The length of the network portion of this address. Enter the gateway address assigned for the device by Spectrum for static IP operation. Enter the IPv6 address of the primary DNS server. Spectrum will provide this information. Secondary DNS Server (IPv6) Enter the IPv6 address of the secondary DNS server. Spectrum will provide this information. Delegated Prefix The network portion of the IPv6 addresses to be allocated to local clients. Delegated Prefix Length The length of the network portion of the IPv6 addresses to be allocated to local clients. RAC2V1A Router User Guide 38 LAN Setup LAN Settings (IPv4) Router Configuration Screen Descriptions You can make changes to the Local Area Network (LAN) configuration here. For changes to take effect, you must click Apply. LAN IP Settings IP Address This field displays the IP address of the LAN. RAC2V1A Router User Guide 39 Router Configuration Screen Descriptions Subnet Mask This field displays the subnet mask of the LAN. DHCP Server Settings Enable DHCP Server Click this checkbox to enable the use of a Dynamic Host Configuration Protocol (DHCP) Server on the network. DHCP is a set of rules used by devices such as a computer, router, or network adapter to allow the device to request and obtain an IP address from a server which maintains a list of addresses available for use. The DHCP server ensures that all IP addresses are unique, e.g., no IP address is assigned to a second device while the first device's assignment is valid

(its lease has not expired). Without DHCP, the IP addresses must be entered manually at each computer in an organization, and a new IP address must be entered each time a computer moves to a new location on the network. Start IP Address/End IP Address Enter the range of IP addresses that the DHCP Server will be allowed to assign to a network device. Lease Time Select the time before the assigned IP address will expire. (After the lease time is up, the user is automatically assigned a new dynamic IP address.) A "lease" is the amount of time that a given IP address will be valid for a computer or other network device. The lease time can vary depending on how long a user is likely to require the Internet connection at a particular location. Using very short leases, DHCP can dynamically reconfigure networks where there are more computers than available IP addresses, such as educational environments. Domain Name Enter the domain name that you want to display on client devices. RAC2V1A Router User Guide 40 NAT NAT Mode Router Configuration Screen Descriptions Select the NAT Mode. RoutedwithNAT: Data will be routed by the device and all the outgoing packets will be NATed. RoutedwithoutNAT: Data will be routed by the device but all the outgoing packets will not be NATed. Bridged: Data will pass through the device directly without any routing and without NAT. UPnP Enable UPnP Advertisement Period Advertisement Time To Live IGMP Proxy Enable IGMP Proxy Click this checkbox to enable UPnP (Universal Plug and Play) on the system. Specify how often (in minutes) the router should advertise its UPnP information. The default is 30 minutes. Enter the maximum number of hops that each UPnP packet can be sent before it is disregarded. The default value is 4, which should be acceptable for most home networks. Click this checkbox to enable the IGMP (Internet Group Management Protocol) proxy on the system. RAC2V1A Router User Guide 41 LAN Settings (IPv6) Router Configuration Screen Descriptions This screen configures LAN side support for IPv6. You can make changes to the Local Area Network (LAN) IPv6 configuration here. For changes to take effect, you must click Apply. Enable Click the checkbox if you want to configure IPv6 in your LAN. If the box is unchecked, your LAN will only have an IPv4 address. When you enable IPv6 in the LAN, a different IPv6-

based subnet is recognized on the LAN, and the local DHCPv6 server will hand out stateless and stateful addresses based on the prefix information broken down from the WAN side delegated prefix. RAC2V1A Router User Guide 42 LAN Settings (IPv6) Router Configuration Screen Descriptions IP Address (IPv6) This field displays the IPv6 address of the LAN. An IPv6 address has eight groups of four hexadecimal digits (0-9, a-f). The groups are separated by colons, for example, 2001:0db8:85a3:0000:0000:8a2e:0370:7334. A double colon (::) is shorthand for an address of all zeros. Prefix Length v6 Length of the network portion of the IPv6 address. Link Local Address (IPv6) IPv6 address that can be used only on this LAN interface. DHCP Server Settings (IPv6) DHCP Ranges Settings (IPv6) Click the checkbox if you want to enable the LAN DHCPv6 pool range. Start IP Address

(IPv6)/End IP Address (IPv6) Enter the range of IPv6 addresses that the DHCP Server will be allowed to assign to a network device. Lease Time

(IPv6) Select the time before the assigned IP address will expire. (After the lease time is up, the user is automatically assigned a new dynamic IP address.) A "lease" is the amount of time that a given IP address will be valid for a computer or other network device. The lease time can vary depending on how long a user is likely to require the Internet connection at a particular location. Using very short leases, DHCP can dynamically reconfigure networks where there are more computers than available IP addresses, such as educational environments. Enable DHCP Relay (IPv6) Click the checkbox to enable DHCP Relay functionality on the system. RAC2V1A Router User Guide 43 Router Configuration Screen Descriptions Multicast Listener Discover (MLD) lets your router discover multicast listeners on an attached link. Click the checkbox to enable MLD proxy functionality on the system. IGMP Proxy Enable MLD Proxy Client List This page shows the IP address, host name and MAC address of each computer that is connected to the network. If a computer does not have a specified host name, then the host name field will be blank. Reserved IP Client List IP Address Host Name Enter the clients IP address. Enter a host name for the client. MAC Address Enter the clients MAC address. Click Add to create a new fixed client lease. Complete the necessary fields in the pop-up window, and then click Apply. RAC2V1A Router User Guide 44 Router Configuration Screen Descriptions Select a client and then click Delete to delete the reserved client from the list. Attached Client List IP Address Host Name The IP address of a connected client. The host name of a connected client. MAC Address The MAC address of a connected client. Click Refresh to update the client list. RAC2V1A Router User Guide 45 Wireless Basic Setup Router Configuration Screen Descriptions RAC2V1A Router User Guide 46 Router Configuration Screen Descriptions While the system has many configuration options, the options on this Basic Setup page are those required by most users. Click the tabs to access the other configuration pages to set advanced options. Hover the mouse pointer over the question mark icon next to an option to view a description of that option. For changes to take effect, you must click Apply. Wireless 2.4 GHz/Wireless 5 GHz SSID Enable SSID Channel Wi-Fi Network Name (SSID) Select the network name (SSID) whose settings you want to display or modify. Click this checkbox to enable the wireless network on the system. Sets a communications channel for the router. The default setting is "Auto", in which the router selects a channel with the least amount of interference to use. For 2.4 GHz, if you manually select a channel, its best to choose channel 1, 6, or 11, since these channels do not overlap. If another router is operating in the area, choose a channel that is farthest away from the channel that unit uses. For example, if another router is using channel 11, set your router to channel 1. For 5 GHz, choose a channel that is farthest away from the channel used by any other router operating in the area. If you experience interference or poor performance on a particular channel, try a different channel. Enter a user-friendly name to identify the wireless network. This name is also referred to as the Service Set Identifier (SSID). The name can be up to 32 characters long. RAC2V1A Router User Guide 47 Wireless Mode Channel Bandwidth Broadcast Network Name

(SSID) AP Isolation Router Configuration Screen Descriptions Select the proper mode to support all of the wireless devices that will connect to the router. 2.4 GHz options are:

802.11n 802.11g+n 5 GHz options are:

802.11n 802.11n&802.11ac 802.11ac The theoretical bandwidth for 802.11g is up to 54 Mbps. The theoretical bandwidth for 802.11n is up to 600 Mbps. The theoretical bandwidth for 802.11ac is up to 1.3 Gbps. Sets the 802.11n Channel Bandwidth. Options are:

20 MHz 20/40 MHz 40 MHz 20/40/80 MHz (5 GHz only) The default bandwidth for 2.4 GHz is 20/40 MHz, and the default bandwidth for 5 GHz is 20/40/80 MHz. Click this checkbox to allow the router to broadcast the network name (SSID). If you enable this, the Wi-Fi network name (SSID) will be visible to all users in the area, including both authorized and unauthorized users. If you would like others not to see the access point, uncheck the checkbox to hide the Wi-Fi network name (SSID). Click this checkbox to enable AP isolation. When enabled each of the wireless clients will be in its own virtual network and will not be able to communicate with one another. This may be useful if you have many guests using the network. Enable WMM Click this checkbox to enable Wi-Fi Multimedia

(WMM) functionality. Enabling WMM can help RAC2V1A Router User Guide 48 Router Configuration Screen Descriptions control latency and jitter when transmitting multimedia content over a wireless connection. Disabling WMM will reduce wireless performance in 802.11n mode. This quality of service mechanism uses four access categories, which in order of priority are: voice, video, best effort and background. This ensures that applications with low tolerance for latency and jitter are treated with higher priority than less-sensitive data applications. WMM sets different wait times for the four categories in order to provide priority network access for applications that are less tolerant of packet delays. Determines the security setting for the router. The recommended setting and default is WPA2-PSK

(Wi-Fi Protected Access 2 Pre-Shared Key). Other settings include WPA/WPA2-PSK (Wi-Fi Protected Access/ Wi-Fi Protected Access 2 Pre-Shared Key) (most compatible); WPA2-Enterprise; or WPA/WPA2-Enterprise. 802.11n performance is only available in WPA2. Enter a password for your network (SSID). Your password is case-sensitive and must be between 8 and 63 characters. You can use any alphanumeric characters (digits 0-9 and letters A-Z, either upper-

or lower-case) and printable special characters

(such as $, !, ?, &, #, @ and others). Security Mode Password

(Network Key) RAC2V1A Router User Guide 49 Advanced Settings Router Configuration Screen Descriptions The Advanced Settings page is used to set up the routers advanced wireless functions. These settings should only be adjusted by an expert administrator since incorrect settings can reduce wireless performance. For changes to take effect, you must click Apply. RAC2V1A Router User Guide 50 Wireless 2.4 GHz/Wireless 5 GHz Router Configuration Screen Descriptions Beacon Interval DTIM Interval RTS Threshold Guard Interval Dynamic Channel Selection Sets the time interval between beacon transmissions in milliseconds. The router uses these transmissions to synchronize the wireless network and its client devices. For compliance with most client devices, the Beacon Interval should remain set at the default of 100ms. The allowable setting range is from 20 to 1024ms. Sets the DTIM (Delivery Traffic Indication Message) Interval. The DTIM Interval informs the wireless client devices of the next available window for listening to broadcast and multicast messages. When the router sends a DTIM beacon, the client devices hear the beacon and then listen for the messages. For compliance with most client devices, the DTIM Interval should be left at 1 ms. The allowable setting range is from 1 to 255 ms. Sets the packet size limit. When the threshold is passed, the ready to send/clear to send (RTS/CTS) function is invoked. The default setting is 2347 bytes. The allowable setting range is from 1 to 2347 bytes. The spacing between transmission of symbols. Can be set to short or long. Select short to provide higher throughput in networks where the coverage distance is small (indoors). Select long to provide higher throughput in networks where the coverage distance is large (outdoors). Click the checkbox if you want this radio to periodically monitor the frequency band for channels that have less traffic than the one in use. If a less congested channel is available, Dynamic Channel Selection allows the radio to make an unsolicited channel change. RAC2V1A Router User Guide 51 Wireless Network Management Radio Resource Management Dynamic Bandwidth Utilization Router Configuration Screen Descriptions Click the checkbox if you want to allow clients to exchange information about network topology. Wireless Network Management also supports network-assisted power saving and network-

assisted roaming. Click the checkbox if you want Spectrum to manage the radio channel and transmit power used on this specific radio. Radio Resource Management lets Spectrum use its knowledge of surrounding networks to select the optimal channel and transmit power to avoid interference with other access points inside and outside your premises. Click the checkbox if you want this specific radio to dynamically adjust the channel bandwidth for this radio to maximize throughput at any given time. Dynamic Bandwidth Utilization makes bandwidth adjustments based on periodic monitoring of the frequency band to expand the channel width when adjacent frequencies are quiet and shrink the channel width when the frequencies being used have interference. Band Steering Band Steering Enable This setting enables the router to steer clients from the 2.4 GHz band to the 5 GHz band as required. Click the checkbox if you would like to enable band steering. Important: In order to use this function, you must go to the Wireless: Basic screen and configure the 2.4 GHz band and the 5 GHz band with the same Wi-Fi Network Name (SSID), Security Mode, and Password (Network Key). See Basic Setup (page 46) for more information. Enter the network name (SSID) that you set up for the 2.4 GHz band/5 GHz band pair on the Wireless:

Basic screen. See Basic Setup (page 46) for more information. Matching SSID RAC2V1A Router User Guide 52 Associated Stats Router Configuration Screen Descriptions This screen provides physical statistics for each associated client. Associated Client List MAC Address The MAC address of an associated client for which statistics are being reported. Network Signal The Network name (SSID) where the client is connected. The average Received Signal Strength Indicator

(RSSI) level of the connected client. TX Rate (bps) The transmission rate that is being reported by the associated client. RX Rate (bps) The receive rate that is being reported by the associated client. RAC2V1A Router User Guide 53 Airtime Fairness Router Configuration Screen Descriptions This screen lets you allocate wireless bandwidth to devices based on air time instead of number of frames. By doing so, you can increase the download speeds for newer, faster devices, even when slower devices are connected to the same wireless network. ATF Enable Click the checkbox to enable Airtime Fairness. Wireless 2.4 GHz SSID Percentage Use these fields to specify what percentage of the 2.4 GHz band you wish to allocate to each wireless network, based on network name (SSID). RAC2V1A Router User Guide 54 Router Configuration Screen Descriptions Wireless 2.4 GHz Client Percentage Use these fields to specify what percentage of the 2.4 GHz band you wish to allocate to each device, based on MAC address. You can enter up to 16 MAC addresses. Wireless 5 GHz SSID Percentage Use these fields to specify what percentage of the 5 GHz band you wish to allocate to each wireless network, based on network name (SSID). Wireless 5 GHz Client Percentage Use these fields to specify what percentage of the 5 GHz band you wish to allocate to each device, based on MAC address. You can enter up to 16 MAC addresses. RAC2V1A Router User Guide 55 QoS Classification Router Configuration Screen Descriptions RAC2V1A Router User Guide 56 Router Configuration Screen Descriptions This screen shows the mapping of network name (SSID) priorities and Differentiated Services Code Point (DSCP) remarking. DSCP specifies the priority for queueing IP packets before they are forwarded. For example, you could set the Home as a Hotspot (HaaH) SSID as a lower priority than the primary SSID to make sure that the owner of the service always gets priority treatment. If you select SSID Priority as the classification method, all of the L3 DSCP/ToS values for the transmission packets (LAN/WAN to WLAN) will be remarked to the same 802.11e QoS control field value. If you select DSCP Remarking as the classification method, the L3 DSCP/ToS value of the transmission packets (LAN/WAN to WLAN) will be remarked to 802.11e QoS control field values following the DSCP remarking table below. Wireless 2.4 GHz/Wireless 5 GHz SSID Enable Classification Classification Method SSID Priority Choose the network name (SSID) settings that you want to display or modify. Click the checkbox if you want to enable this classification on your system. Choose a classification method for your router. Options are SSID Priority or DSCP Remarking. If you choose SSID Priority as the classification method, choose the priority to assign to each packet. Options are:

0 maps to Layer 2 CoS value 2 and 802.11e WMM Access Category BK. This is the lowest priority. 1 maps to Layer 2 CoS value 0 and 802.11e WMM Access Category BE. 2 maps to Layer 2 CoS value 4 and 802.11e WMM Access Category VI. 3 maps to Layer 2 CoS value 6 and 802.11e WMM Access Category VO. This is the highest priority. RAC2V1A Router User Guide 57 DSCP Remarking Table Router Configuration Screen Descriptions This section defines the mapping relationship between L3 DSCP value, L2 ToS value, and 802.11e QoS control field value. We recommend that you do not change the default values displayed on the screen. DSCP Binary Decimal Wireless Tos Log The DSCP value for this entry. The binary value for this DSCP entry. The decimal value for this DSCP entry. The wireless type of service. Larger values indicate a higher priority. This screen shows a log of communication statistics for your wireless connections. This information may be helpful in troubleshooting issues with your wireless network. RAC2V1A Router User Guide 58 Firewall Firewall Settings Router Configuration Screen Descriptions The router is equipped with a firewall that will protect the network from a wide array of common hacker attacks, including Ping of Death (PoD) and Denial of Service (DoS) attacks. You can disable the firewall function if necessary. Turning off the firewall protection will not leave the network completely vulnerable to hacker attacks, but it is recommended that you enable the firewall whenever possible. For changes to take effect, you must click Apply. Firewall Enable/Disable Enable Firewall Click the checkbox to enable the firewall on the system. Enable unsolicited flow forwarding/

transparent mode Click the checkbox if you want to suspend simple security capabilities associated with the firewall. Doing so allows for more flexibility and reliability for applications that require clients to be contacted inside the home while minimizing the impact on security. RAC2V1A Router User Guide 59 Port Forwarding Router Configuration Screen Descriptions The port forwarding function forwards inbound traffic from the Internet to a specified single device on the network. Examples include allowing access to a web server on the network, peer-to-peer file sharing, some gaming and videoconferencing applications and others. This function allows you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through the router to the internal network. Port Forwarding Service List Clear Entry Select the kind of service you would like to set up, and click Add. The pre-defined port forwarding rules will be displayed in the table. You must edit the private IP address on the LAN where you want external calls to go, or you can choose Custom and define your own port forwarding rules. When you are finished, click Apply. To remove the rule from a table and stop forwarding that port, select the entry that you want to clear and click Clear. RAC2V1A Router User Guide 60 Port Forwarding Table Router Configuration Screen Descriptions Enable Clear this checkbox if you want to stop forwarding this port but do not want to remove it from the table. Description Enter a name for the port you want to forward. WAN Inbound Port Type Private IP Address Private Port Port Triggers Choose whether the port forward should be directed to a client on the default LAN (192.168.1.x) or on a Routing Information Protocol (RIP) gateway. Enter the inbound port range for the port you want to forward. It should be the same range as the local port. Set the format for the port. Options are TCP, UDP, or BOTH. Enter the IP address of the machine on the LAN where you want the connections to go. Enter the private port range for port you want to forward. It should be the same range as the inbound port. RAC2V1A Router User Guide 61 Router Configuration Screen Descriptions Port triggers let you configure dynamic triggers to specific devices on the LAN. This allows special applications that require specific port numbers with bi-directional traffic to function properly. Applications such as video conferencing, voice, gaming and some messaging program features may require these special settings. To add a new port trigger, click Add. Complete the necessary fields in the pop-up window, and then click Apply. To edit a port trigger, select the entry and then click Edit. To delete a port trigger, select the entry and then click Delete. Description Enter a description for the trigger you want to set up. Outbound Port Specify the range of outbound port numbers. Type Inboud Port DMZ Specify the type of port. Options are TCP, UDP, and BOTH. Specify the range of inbound port numbers. RAC2V1A Router User Guide 62 Router Configuration Screen Descriptions The DMZ feature allows you to specify one computer on the network to be placed outside of the NAT firewall. This may be necessary if the NAT feature is causing problems with an application such as a game or video conferencing application. Use this feature only on a temporary basis. The computer in the DMZ is not protected from hacker attacks. To put a computer in the DMZ, click the Enable checkbox, enter its IP address, and click Apply. DMZ IPv4 Settings Enable Static IP Private IP DMZ IPv6 Settings Enable Clear this checkbox if you want to remove the computer from the DMZ and disable the DMZ on the network. Displays routers WAN IP address. This is the address that external devices will use to contact the computer in the DMZ. Enter the IPv4 address of the computer to be placed in the DMZ. Be sure that the address is not in the range of addresses delivered by the DHCP server if enabled. Once you place the computer in the DMZ, all ports on the computer are open to the Internet and not protected. Clear this checkbox if you want to remove the computer from the DMZ and disable the DMZ on the network. IPv6 DMZ Host IP Enter the IPv6 address of the computer to be placed in the DMZ. Be sure that the address is not in the range of addresses delivered by the DHCP server if enabled. Once you place the computer in the DMZ, all ports on the computer are open to the Internet and not protected. RAC2V1A Router User Guide 63 WAN Ping Blocking Router Configuration Screen Descriptions You can configure the router not to respond to an ICMP Ping (ping to the WAN port). This offers a heightened level of security. Block ICMP Ping Block ICMP Ping Enable Application Layer Gateway Settings Click this checkbox to enable WAN Ping Blocking. RAC2V1A Router User Guide 64 Router Configuration Screen Descriptions Application layer gateway settings allow the router to recognize and treat certain network protocols specially. Important: You should not change these settings unless recommended by your service provider. Most users will never need to change the settings on this page. Application Layer Gateway Click the checkbox for each network protocol for which you want special handling. Options are IPSec, PPTP, PppoePassthrough, IpsecPassthrough, PptpPassthrough, and L2tpPassthrough. MAC Filter MAC address filtering gives you an extra layer of security by allowing you to specify which devices can access your network. Whenever a new device tries to join your network, the router checks the MAC address of the device against a list of approved addresses. You can choose to allow

(whitelist) or deny (blacklist) MAC addresses. Whenever a device tries to access your network, the router checks the MAC filter settings to determine whether the device should be allowed to access your network. RAC2V1A Router User Guide 65 MAC Filter Service Router Configuration Screen Descriptions Choose either Deny to prevent the specified MAC addresses from reaching the Internet or Allow to allow the specified MAC addresses to reach the Internet. Then click Apply. MAC Filter Settings Device Name Enter a name for the device that you want to specify. This should be a name that you will recognize (for example, "Home Router" or "Jane's Office"). MAC Address Enter the MAC address for the device that you want to specify. You can also select the MAC address from a list of online clients. Click Add to create a new MAC filter setting. Complete the necessary fields in the pop-up window, and then click Apply. To delete a MAC filter setting, select the entry and then click Delete. Parental Controls Parental Control lets you block access to the Internet (or certain sites on the Internet) at various times that you specify. You can block sites based on keywords, URL, or custom filters that you set up. RAC2V1A Router User Guide 66 Router Configuration Screen Descriptions Create Filter Choose whether you want to create a filter based on keywords, URL, or custom parameters that you define. Parental Controls - Block URL Use this screen to block access to websites based on their URLs (web addresses). The IP address resolved by the fully qualified domain name

(FQDN) will also be blocked. Description Type a description for the filter you are creating. RAC2V1A Router User Guide 67 MAC Address URL Days Time Router Configuration Screen Descriptions Type the MAC address of the device that you want to restrict from accessing the URLs that you specify. If you want the filter to apply to multiple clients, you must enter the MAC addresses one by one. If you do not specify a MAC address, the filter will apply to all clients. Type the URL of the site that you want to block as part of this filter. If you would like to block multiple sites, you will enter them one at a time and click Apply after each URL that you want to block. Select the days that you would like for this filter to be in effect. Select the time of day that you would like for this filter to be in effect. Display Filters This area displays any filters that you have already defined and lets you modify or delete those filters. If you want to edit an existing filter, click Edit. If you want to delete an existing filter, select the filter and click Delete. If you want to remove all of your filters, click Remove All. RAC2V1A Router User Guide 68 Parental Controls - Block Keywords Router Configuration Screen Descriptions Use this screen to block access to websites based on keywords that appear in the websites HTTP header or DNS query. Description Type a description for the filter you are creating. MAC Address Type the MAC address of the device that you want to restrict from accessing sites that contain these keywords. If you want the filter to apply to multiple clients, you must enter the MAC addresses one by one. If you do not specify a MAC address, the filter will apply to all clients. RAC2V1A Router User Guide 69 Keywords Days Time Router Configuration Screen Descriptions Type the keywords that you want to block as part of this filter. If you want to block multiple keywords, you will enter them one at a time and click Apply after each keyword that you want to block. Select the days that you would like for this filter to be in effect. Select the time of day that you would like for this filter to be in effect. Display Filters This area displays any filters that you have already defined and lets you modify or delete those filters. If you want to edit an existing filter, click Edit. If you want to delete an existing filter, select the filter and click Delete. If you want to remove all of your filters, click Remove All. RAC2V1A Router User Guide 70 Parental Controls - Custom Router Configuration Screen Descriptions Use this screen to block access to websites based on custom filters that you define. Description Use this field to type a description for the filter you are creating. RAC2V1A Router User Guide 71 MAC Address URL Start Port End Port Protocol Days Time Allow/Block Router Configuration Screen Descriptions Type the MAC address of the device that you want to restrict from accessing the URLs that you specify. If you want the rule to apply to multiple clients, you must enter the MAC addresses one by one. If you do not specify a MAC address, the rule will apply to all clients. Type the URL of the site that you want to block as part of this filter. If you would like to block multiple URLs, you will enter them one at a time and click Apply after each URL that you want to block. Type the starting number for the range of ports that you want to block. Type the ending number for the range of ports that you want to block. Select the protocol that you want to block. Select the days that you would like for this filter to be in effect. Select the time of day that you would like for this filter to be in effect. Use the drop-down menu to specify whether you want this filter to allow or block access under the conditions you specify. Display Filters This area displays any filters that you have already defined and lets you modify or delete those filters. If you want to edit an existing filter, click Edit. If you want to delete an existing filter, select the filter and click Delete. If you want to remove all of your filters, click Remove All. RAC2V1A Router User Guide 72 IPv6 Client Filter Router Configuration Screen Descriptions This screen lets you whether incoming ports to LAN IPv6 clients should be able to bypass the default IPv6 firewall on the router. You can also choose to block outgoing ports on LAN IPv6 clients. Click Add to create a new IPv6 client filter. Complete the necessary fields in the pop-up window, and then click Apply. Select a filter and then click Edit to edit the filter. Select a filter and then click Delete to delete the filter from the list. IPv6 Client Filter Action/Direction Select whether the client device should be allowed to bypass the IPv6 firewall (Allow+Incoming) or blocked from accessing the Internet

(Deny+Outgoing). Client IP Address Enter the client IPv6 address for which this rule applies. You can enter a single address or a range of addresses. RAC2V1A Router User Guide 73 Type Port Router Configuration Screen Descriptions The traffic type for which this rule applies. Options are:

TCP UDP Both (TCP and UDP) ICMPv6 Enter the port or range of ports to which this entry applies. USB USB Status The USB status shows any USB devices that are connected to the router. Click Refresh to update the list. If you want to disconnect a device, select the device and click Remove. Then unplug the device. Available Volumes Volume Name The volume name of a connected USB device. Total Space Free Space The total space available on the associated USB device. The amount of free space available on the associated USB device. RAC2V1A Router User Guide 74 File Sharing Router Configuration Screen Descriptions File sharing lets you configure folders on the USB device so that you can share files with other devices. An FTP server makes the folder available for remote users over the Internet. Shared folders are available to users on your local network. RAC2V1A Router User Guide 75 FTP Server Settings Router Configuration Screen Descriptions Enable FTP Server FTP Server Access Click this box to enable an FTP server on your USB device. Use this field to specify the folder that you want to make available as an FTP server. Share Folder Settings Enable Share Folders Share Folders Access Click this box to enable shared folders on your USB device. Use this field to specify the folder that you want to make available as a shared folder. HTTPS Server Settings Enable HTTPS Server HTTPS Server Access NFS Settings Click this box to enable an HTTPS server on your USB device. Use this field to specify the folder that you want to make available as an HTTPS server. Enable NFS Click this box to enable NFS on your USB device. AFP Settings Enable AFP Click this box to enable AFP on your USB device. Share Folders Access Use this field to specify the folder that you want to make available for AFP. Available Share Folders:

Use this section to add, edit, or delete shared folders on the USB device. RAC2V1A Router User Guide 76 Media Sharing Router Configuration Screen Descriptions Media sharing lets you configure network folders so that you can share media (movies, songs and pictures) with other devices on your network. Media Sharing Settings Enable Media Sharing Media Sharing Name Click this box to enable media sharing on your USB device. Use this field to specify the folder that you want to make available for media sharing. RAC2V1A Router User Guide 77 USB Access Control Router Configuration Screen Descriptions USB access control lets you specify which USB devices are allowed to have access to your network. Enable USB Access Control Select this box if you want to turn on USB access control. USB access control is disabled by default. Approved USB Device This section shows the USB devices that are able to access your network. If you want to restrict a device so that it cannot access your network, select the device and click Delete. Attached USB Device This section shows the USB devices which are attached to your router. RAC2V1A Router User Guide 78 Utilities System Information Router Configuration Screen Descriptions This page shows a summary of the systems status. RAC2V1A Router User Guide 79 Hardware Software Version Router Configuration Screen Descriptions Serial Number This field displays the serial number of your router. Bootcode Version Hardware Version This field displays the bootcode version. This field displays the hardware version. Firmware Version This field displays the firmware version. WAN Status Summary WAN MAC Address Connection Setup This field displays the WAN MAC address. This field displays the connection type: Dynamic or Static. IP Address This field displays the WAN IP address. Subnet Mask This field displays the WAN subnet mask. Primary DNS This field displays the Primary DNS IP address. Secondary DNS This field displays the Secondary DNS IP address. Gateway This field displays the gateway IP address. LAN Status Summary MAC Address This field displays the LAN MAC Address. IP Address This field displays the IP Address of the LAN. Subnet Mask This field displays the subnet mask of the LAN. DHCP Server This field displays the status of the DHCP Server:

Enabled or Disabled. Other Features Summary Firewall Settings This field indicates whether the firewall settings are SSID Security UPNP enabled or disabled. This field indicates the network name (SSID). This field indicates the security mode. This field indicates whether the UPnP feature is enabled or disabled. RAC2V1A Router User Guide 80 Router Configuration Screen Descriptions Remote Management This field indicates whether the Remote Management feature is enabled or disabled. WPS Restart Router This field indicates whether the WPS function is enabled or disabled. It may be necessary to restart (reset) the router if it stops working properly. Restarting the router will not delete any of the configuration settings. To restart the router, click Restart. Note: A dialog box prompts you to confirm that you want to restart the router. Click OK to restart now or click Cancel to restart later. RAC2V1A Router User Guide 81 Factory Defaults Router Configuration Screen Descriptions This screen lets you revert all of the routers configuration settings to the factory default setting. Click Factory Defaults to revert to the factory default configuration settings. Note: A dialog box prompts you to confirm that you want to restore the factory default settings. Click OK to restore now or click Cancel if you do not want to restore now. RAC2V1A Router User Guide 82 System Settings Router Configuration Screen Descriptions This page allows you to make certain system settings. For changes to take effect, you must click Apply. Administrator Login Current Password Enter the old password to change the administrator password. New Password/

Confirm New Password Enter the new password in both fields to change the administrator password. RAC2V1A Router User Guide 83 Login Timeout Router Configuration Screen Descriptions Enter the number of minutes that these web pages can remain idle before the user is logged out. Time And Time Zone Current Time Displays the current time. Current Language Select the language you want to see displayed in the GUI. Time Zone Select the time zone. Daylight Savings Click this checkbox to automatically update the system clock for Daylight Saving Time. The host name or IP addresses of the NTP servers that you want to use. 1-4 allow you to select a server from a drop-down list. 5 allows you to type in a server name. NTP Server 1-5 System Logs RAC2V1A Router User Guide 84 Router Configuration Screen Descriptions This page displays the system logs. These may include GUI login authentication logs, TR069 logs, NTP logs, and Wi-Fi access logs, among others. Click Refresh to update the list. DDNS DDNS (Dynamic DNS) lets you give Internet users a fixed domain name

(instead of an IP address which may periodically change). This allows various locations on the Internet to access the router and the applications that are set up in the gateway's port forwarding table without knowing your current IP address. For changes to take effect, you must click Apply. Note: You must first create an account with a DDNS provider in order to use DDNS. The DDNS provider maps the chosen domain name to your IP address. DDNS Setting DDNS Enable Click this checkbox to enable DDNS on the system. DDNS Service Sets the DDNS provider that the account uses. Available options are No-IP, DuckDNS and Dynu. User Name Enter the user name for the DDNS account. RAC2V1A Router User Guide 85 Password Domain Name Blocked Device Router Configuration Screen Descriptions Enter the password for the DDNS account

(provided by your DDNS provider). Enter the domain name you selected to use with the DDNS account. This page shows a list of devices that have been blocked from your router, listed by MAC filter and USB access control. From MAC Filter Device Name MAC Address The host name of a client for which an explicit MAC filter has been set up on the Firewall: MAC Filter page. The MAC address of a client for which an explicit MAC filter has been set up on the Firewall: MAC Filter page. From USB Access Control Volume Name File System The volume name of a USB device for which an explicit USB access control has been set up on the USB: USB Access Control page. The file system method (such as FAT, NFTS and so on) of a USB device for which an explicit USB RAC2V1A Router User Guide 86 Router Configuration Screen Descriptions access control has been set up on the USB: USB Access Control page. The capacity of a USB device for which an explicit USB access control has been set up on the USB:

USB Access Control page. Capacity QoS Quality of Service (QoS) refers to the overall performance of your network. This screen allows you to prioritize certain applications such as online gaming while minimizing the effects on network performance during busy periods. Enable QoS Click this checkbox to enable QoS Prioritization. RAC2V1A Router User Guide 87 Router Configuration Screen Descriptions Uplink bandwidth Maximum Enter the highest speed that you want to allow for uploads in this policy. SpeedTest Click this button to run a speed test and verify your connection speed. QoS Policy for Enter a name for this QoS policy. MAC Address Device Name Priority Enter the MAC address of the client device that will be affected by this policy Enter a name for the client device that will be affected by this policy. Choose the priority for this policy. In the event of conflicting policies, this priority will be used to determine which policy takes precedent. RAC2V1A Router User Guide 88 Troubleshooting The router is plugged in, but the light is off Check all power connections. Is the power cord plugged in firmly at both ends?

If you plugged the power cord into a power strip, make sure the strip is switched on. Try to plug the power cord into a different outlet. If the outlet is controlled by a wall switch, make sure the switch is on. Finally, check the fuse or circuit breaker panel. I'm not getting on the Internet (all connections) It may take several minutes to establish a connection the first time you power up the router, especially when many people are online. Always leave the router plugged into AC power and connected to the modem. Check the light on the front. It should be blue. Check the cable connections. Connectors should be tight. Cables should not be pinched, kinked, or bent sharplyany of these can cause a break or short in the cable. (You may have to replace the cable). Proceed to the Ethernet or wireless solutions if necessary. I'm not getting on the Internet (Ethernet) If you are using a switch, is the switch turned on?

Are you using the right type of Ethernet cable? Use an RJ45 Cat5e cable for direct connection to a computer; use a cross-over cable for connection to a switch. Unplug the power from the router and wait a few seconds, then plug the power back in. A misconfiguration could lock out all access to the router. If you think this has happened, see Factory Defaults (page 82). I'm not getting on the Internet (Wireless) Check the light on the front. It should be blue. Does the connection utility discover your wireless LAN? If you turned off Broadcast Wi-Fi Network Name (SSID) you need to manually enter the name of the wireless LAN in the connection utility. RAC2V1A Router User Guide 89 Change the security setting to another setting. Troubleshooting A misconfiguration could lock out all access to the router. If you think this has happened, see Factory Defaults (page 82). Make sure that your wireless device is compatible with the wireless mode that you selected. See Setting the Wireless Mode (page 22). My wireless Internet connection stops working sometimes This may be caused by distance or interference. Try moving the device closer to the router. Two common sources of interference are 2.4 GHz remote telephones and microwave ovens. If you cannot remove the interfering product, try using a different channel. I can get on the Internet, but everything is slow If the Web site you are visiting is very popular, that site may be having trouble servicing all the requests. If other sites download quickly, wait for a few minutes and try again. Web site traffic during peak hours may also affect the connection speed. Other communications on the LAN, or interference with wireless connections, may slow down the connection. RAC2V1A Router User Guide 90 Safety Requirements The RAC2V1A router complies with the applicable requirements for performance, construction, labeling and information when used as outlined below:

Do not use product near water (i.e. wet basement, bathtub, sink or near a swimming pool, etc.), to avoid risk of electrocution. The product shall be cleaned using only a damp, lint-free, cloth. No solvents or cleaning agents shall be used. Do not use spray cleaners or aerosols on the router. Avoid using and/or connecting the equipment during an electrical storm, to avoid risk of electrocution. Do not locate the equipment within 6 feet (1.9 m) of a flame or ignition source (i.e. heat registers, space heaters, fireplaces, etc.). Use the power adapter included with the equipment. Equipment should be installed near the power outlet and should be easily accessible. In areas of high surge events or poor grounding situations and areas prone to lightning strikes, additional surge protection may be required (i.e. PF11VNT3 from American Power Conversion) on the AC and Ethernet lines. When the router is connected to a local computer through Ethernet cables, the computer must be properly grounded to the building/residence AC ground network. All plug-in cards within the computer must be properly installed and grounded to the computer frame per the manufacturers specifications. Ensure proper ventilation. Position the router so that air flows freely around it and the ventilation holes on the unit are not blocked. Do not mount the router on surfaces that are sensitive to heat and/or which may be damaged by the heat generated by the modem or its accessories. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in RAC2V1A Router User Guide 91 Safety Requirements accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that Increase the separation between the equipment and receiver. to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 25cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANADA Operation of this device is restricted to indoor use only RAC2V1A Router User Guide 92 2017 ARRIS Enterprises LLC. All Rights Reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without written permission from ARRIS Enterprises LLC. (ARRIS). ARRIS reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of ARRIS to provide notification of such revision or change. ARRIS and the ARRIS logo are all trademarks of ARRIS Enterprises LLC. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks or the names of their products. ARRIS disclaims proprietary interest in the marks and names of others. ARRIS provides this guide without warranty of any kind, implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. ARRIS may make improvements or changes in the product(s) described in this manual at any time. The capabilities, system requirements and/or compatibility with third-party products described herein are subject to change without notice.