FCC ID: TKZMM610X-001 Wi-Fi HaLow Module

www.asiarf.com TEL: +886-2-29407880 FAX: +886-2-29407800 Wi-Fi HaLow Module MM610X-001 1. Product overview MM610X-001 is a Wi-Fi HaLow Sub-GHz wireless module based on Morse Micro MM6108 RF SOC. HaLow (pronounced halo) is a low-power, long-range version of the IEEE 802.11Wi-Fi standard. HaLow is based on the Wi-Fi Alliance 802.11ah specification and is expected to play an important part in the Internet of Things

(IoT). Wi-Fi CERTIFIED HaLow, the designation for products incorporating IEEE 802.11ah technology, augments Wi-Fi by operating in spectrum below 1 gigahertz (GHz) to offer longer range and lower power connectivity. Excellent RF performance, MM610X-001 module has excellent sensitivity with good selectivity and blocking performance. MM610X-001 module come with U.FL connector for external Sub-GHz antenna. There are many IO interfaces: UART, SDIO, SPI, I2C and rich GPIOs for PWM and switch functions. 2 KMs LOS distance communication: MM610X-001 module is tested to support up to 2000 meters LOS distance communication, good for both indoor and outdoor IoT applications. 20Mbps UDP Throughput is the best capacity compared with all Wireless IoT long distance throughput. The Phy data rate is 32.5Mbps. 1F, 7, Houde Street, Younghe District, New Taipei City, Taiwan, R.O.C 1 www.asiarf.com TEL: +886-2-29407880 FAX: +886-2-29407800 2. Features:

Protocol 802.11ah OFDM PHY supporting future WFA HaLow certification BPSK & QPSK, 16-QAM & 64-QAM Modulation Automatic frequency & gain control Packet detect & channel equalization Forward Error Correction (FEC) coding & decoding Supports Modulation and Coding Scheme (MCS) levels MCS 0-7 and MCS 10 Supports 1 MHz and 2MHz duplicate mode Supports optional Traveling Pilot 802.11ah MAC supporting WFA HaLow certification Support for STA and AP roles Listen-Before-Talk (LBT) access with energy detect 802.11 power save 802.11 fragmentation and defragmentation Power-Saving Target Wake Time (TWT) support for long battery life Automatic and manual MCS rate selection Radio Operation Single-stream max data rate of 32.5 Mbps (MCS=7, 64-QAM, 8MHz channel, 4 Sec GI) Radio supporting worldwide Sub-1 GHz frequency bands Frequency Range: 850-950 MHz Channel width options of 1/2/4/8 MHz Transmitter Performance Tx output power (dBm): +21 dBm (Typical) MCS0 RF Interface External antenna connector Power Management Unit (PMU) for various modes of operation Power-down (interrupt driven wake) Hibernate mode (internal / external wake) Target Wake Time mode Active Receive / Transmit mode Integrated DC-DC converter supports a wide supply voltage, from 3.0V to 3.6V Regulatory Certifications coming soon CE/FCC/IC/TELEC/NCC/RCM ESD: HBM 2KV / MM 200V, Latch-up: 150mA Halogen-free / RoHS 2.0 / Reach Annex 14 & 17 Operating Range 3.0-3.6V for VBATT and VDDFEM. 1.8-3.6V for VDDIO

-40 to +70C 1F, 7, Houde Street, Younghe District, New Taipei City, Taiwan, R.O.C 2 www.asiarf.com TEL: +886-2-29407880 FAX: +886-2-29407800 Dimensions 22 mm x 17.0 mm x 2.0 mm (module) Security AES encryption engine Hardware support for SHA1 and SHA2 hash functions (SHA-256, SHA-384, SHA-512) WPA3 including protected management frames (PMF) Opportunistic Wireless Encryption (OWE) MCU Peripherals 12-bit 1 Msps SAR ADC 12 GPIO 2 UART, 1 x SPI, 1 x I2C Power Management Unit for power state switching SDIO 2.0 compliant slave interface SDIO 2.0 Default Speed (DS) at 25MHz SDIO 2.0 High Speed (HS) at 50MHz Support for both 1-bit and 4-bit data mode Support for SPI mode operation Surveillance Cameras and Sensors Cloud Connectivity Low-power Sensor Networks Building Automation Systems (BAS) Asset Tracking and Management Machine Performance Monitors & Sensors Building Access Control & Security Drone Video and Navigation Communications Connected Toys and Games Rural Internet Access Agricultural and Farm Networks Utility Smart Meter and Intelligent Grid Proximity Sensors Industrial Automation Controls Smart Home Automation EV Car Chargers Appliances Construction Site Connectivity Smart Signs and Kiosks Retail Point-of-Sale Terminals Vehicle-to-Vehicle Communications IP Sensor Networks Biometric IDs and Keypads Warehouse Connectivity Intelligent Lighting Controls BT/ZigBee()/Z-Wave() to Wi-Fi HaLow Gateways 1F, 7, Houde Street, Younghe District, New Taipei City, Taiwan, R.O.C 3 www.asiarf.com TEL: +886-2-29407880 FAX: +886-2-29407800 Wi-Fi to Wi-Fi HaLow Bridges Wi-Fi HaLow Client Adapters/Dongles Smart City Networks 3. Specification:

Item RF Transmit Power Antenna PHY Rate Physical Connectors Operation Voltage Operation Temperature Security Host Interface Specification Tx output power (dBm): +21 dBm (Typical)@MCS0 (+/- 2dBm)

+18 dBm (Typical)@MCS7 (+/- 2dBm) 1 x UFL (IPEX) connector Up to 32.5Mbps 43 holes PCB board edge stamp holes 3.0V to 3.6V

-40 to 70 WPA3 SDIO, SPI RF Receiver Sensitivity Coding Rate Modulatio n Scheme MCS Index 0 1 2 3 4 5 6 7 10 BPSK QPSK QPSK 16-QAM 16-QAM 64-QAM 64-QAM 64-QAM BPSK Phy Rate (kbps) per BW 4MHz 2Mhz 1MHz 1500 722 333 3000 1444 667 4500 2167 1000 6000 2889 1333 9000 4333 2000 12000 5778 2667 13500 6500 3000 7222 15000 3333 N/A 1/2 1/2 3/4 1/2 3/4 2/3 3/4 5/6 1/2 x 2 167 Spec Sensitivity (dBm) per BW 1MHz 8MHz

-105 3250

-102 6500

-99 9750

-96 13000

-93 19500

-89 26000 29250

-88 325500 -87 4MHz 8MHz

-101

-97

-95

-91

-88

-84

-83

-81

-97

-93

-92

-88

-85

-81

-80

-78 2Mhz

-103

-100

-97

-94

-90

-87

-85

-84 N/A Transmit Power consumption Mode Transmit Current (MCS7, 16dBm, 100% D.C.) Transmit Current (MCS0, 21dBm, 100% D.C.) Condition TA=25, VBAT=VDDIO=3.3V 1MHz channel 2MHz channel 4MHz channel 8MHz channel 1MHz channel 2MHz channel 4MHz channel 8MHz channel

-107 VBAT Current

(Typ) 51 VFEM

(Typ) 104 104 102 99 57 151 151 151 147 55 62 72 60 66 78 mA mA Unit mA mA mA mA mA mA 1F, 7, Houde Street, Younghe District, New Taipei City, Taiwan, R.O.C 4 www.asiarf.com TEL: +886-2-29407880 FAX: +886-2-29407800 FCC Compliance Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. This device must accept any interference received, including interference that may cause undesired operation. Product that is a radio transmitter is labeled with FCC ID. FCC Caution:

(1) Exposure to Radio Frequency Radiation. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

(2) Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.

(3) This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Changes or modifications to this unit not expressly approved by the party

(4) responsible for compliance could void the user authority to operate the equipment. IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co location with another transmitter), then the FCC authorization is no longer considered valid, and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. The modular transmitter is only FCC authorized for the specific rule partslisted on the grant, and that the product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The module has been tested for compliance to FCC Part 15 (15.247) If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. OEM integration instructions:

1F, 7, Houde Street, Younghe District, New Taipei City, Taiwan, R.O.C 5 www.asiarf.com TEL: +886-2-29407880 FAX: +886-2-29407800 This device is intended only for OEM integrators under the following conditions, The module is only limited to installation in mobile applications. The antenna must be installed such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmit or antenna. The module shall be only used with the integral antenna(s) that has been originally tested and certified with this module. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirement with this module installed (for example, digital device emission, PC peripheral requirements, etc.) OEM integration instructions:

In the event that these conditions cannot be met (for example certain laptop configuration or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these and circumstance, the OEM integrator will be responsible for re-evaluating. The end product (including the transmitter) and obtaining a separate FCC authorization End product labeling:

This transmitter module is authorization only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following,

"Contains Transmitter Module FCC ID: TKZMM610X-001 or Contains FCC ID:

TKZMM610X-001"

The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Information that must be placed in the end user manual:

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 1F, 7, Houde Street, Younghe District, New Taipei City, Taiwan, R.O.C 6 www.asiarf.com TEL: +886-2-29407880 FAX: +886-2-29407800 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated. Frequency Band 863-930MHz Antenna Type Dipole Antenna Model Number ANTSM90003004001 Gain(dBi) 2.5 1F, 7, Houde Street, Younghe District, New Taipei City, Taiwan, R.O.C 7 www.asiarf.com TEL: +886-2-29407880 FAX: +886-2-29407800 This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites dexposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20cm de distance entre la source de rayonnement et votre corps This radio transmitter [IC: 9968A-MM610X001] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna Type Dipole Antenna Model Number ANTSM90003004001 Antenna Gain(dBi) 2.5 Remark For 863-930MHz Le prsent metteur radio [IC: 9968A-MM610X001] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains transmitter module IC: IC: 9968A-MM610X001. Contient le module d'mission IC: IC: 9968A-MM610X001 The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online. This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. NCC

1F, 7, Houde Street, Younghe District, New Taipei City, Taiwan, R.O.C 8

Asia RF MM610X-001 Wi-Fi Halow Module FCC ID: TKZMM610X-001 IC: 9968A-MM610X001

@CcxxxxyYyyyzzw FECEEH

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: July 17, 2023 FCC ID: TKZMM610X-001 RE: Attestation Statements Part 2.911(d)(5)(i) Filing AsiaRF Co., Ltd. (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. RE: Attestation Statements Part 2.911(d)(5)(ii) Filing AsiaRF Co., Ltd. (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, Applicant Address

: AsiaRF Co., Ltd.

: 1F, 7, Houde Street, Yonghe Dist. New Taipei City, 23455 Taiwan Signature

_________________________________ Name and Job Title.

: Paul Lai, CEO E-mail Tel.

: paul@asiarf.com

: 886229407880

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: July 17, 2023 Ref: Attestation Statements Part 2.911(d)(7) Filing Grantee Code: TKZ FRN: 0016109175 AsiaRF Co., Ltd. (the applicant) certifies that, as of the date of the filing of the application, WiBravo Communication Inc. is our designated U.S. agent for service of process for the above referenced Grantee Code. AsiaRF Co., Ltd. accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges their responsibility to inform the FCC whenever the designated agent information changes. WiBravo Communication Inc. accepts the designation by the applicant as the U.S. agent to accept service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. Designated U.S. Agent Information:

Company Name: WiBravo Communication Inc. Address: 521 Ala Moana Blvd., Suite M-415, Honolulu, Hawaii 96813, USA Contact Person: Paul Lai Tel.: +886911071257 Email: paul@wibravo.com Sincerely, Applicant AsiaRF Co., Ltd. Paul Lai, CEO Signature:

U.S. Agent WiBravo Communication Inc. Paul Lai Signature:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Date: July 17, 2023 Subject: declaration of composite/rated equipment for FCC ID: TKZMM610X-001 To Whom it may concern, We, the undersigned, would like to declare that the composite portion catagorized as Class B All other devices has been authorized under the Supplier's Declaration of Conformity (SDoC) procedures. Sincerely, Applicant Address

: AsiaRF Co., Ltd.

: 1F, 7, Houde Street, Yonghe Dist. New Taipei City, 23455 Taiwan Signature

_________________________________ Name and Job Title.

: Paul Lai, CEO E-mail Tel.

: paul@asiarf.com

: 886229407880

Confidentiality Request Letter Date: July 17, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 FCC ID: TKZMM610X-001 Permanent Confidentiality Request Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. 1. Block Diagram 2. Schematic Diagram 3. Theory of Operation The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Applicant Address

: AsiaRF Co., Ltd.

: 1F, 7, Houde Street, Yonghe Dist. New Taipei City, 23455 Taiwan Signature

_________________________________ Name and Job Title.

: Paul Lai, CEO E-mail Tel.

: paul@asiarf.com

: 886229407880

Modular Approval Request Letter Date: July 17, 2023 Subject: Modular Approval Attestation FCC ID: TKZMM610X-001 Dear Reviewer, We, AsiaRF Co., Ltd., would request Wi-Fi HaLow Module approved under single module approval authorization. The requirements regulated in 47 CFR 15.212 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The shielding of the radio portion can be demonstrated in exhibition External Photo. 2. The requirement of buffered inputs: Buffered data inputs stage has been integrated in chip

(MM6108). 3. The requirement of power supply regulation: The part number of the power regulator is

(MM6108). 4. The requirements of section 15.203 and 15.204(C): The requirements of antenna connector and spurious emission have been fulfilled. Please reference the exhibition Test Report. 5. The requirement of stand-alone test configuration: Please reference exhibition Test Configuration Photo for the stand-alone test configuration. 6. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the users manual of this module. Please also see the exhibition Label Sample. 7. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been clearly stated in the Users Manual. 8. The requirement of RF exposure: Please refer exhibition RF Exposure test report for the compliance of exposure rule. Please do not hesitate to contact me for any questions of this request letter. Thank you. Applicant Address

: AsiaRF Co., Ltd.

: 1F, 7, Houde Street, Yonghe Dist. New Taipei City, 23455 Taiwan Signature

_________________________________ Name and Job Title.

: Paul Lai, CEO E-mail Tel.

: paul@asiarf.com

: 886229407880

Letter of Authorization Date: July 17, 2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Subject: Product Certification Representative Authorization Letter FCC ID: TKZMM610X-001 Product Name: Wi-Fi HaLow Module To whom it may concern:

We the undersigned, hereby authorize following person to act as our agent in the preparation of an application for equipment authorization to the FCC Rules and Regulations. Sporton International Inc. Address :

No.52, Huaya 1st Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Name

: Leo Huang Job Title : VP e-mail

: Leohuang@sporton.com.tw We further certify that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002(b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Applicant Address

: AsiaRF Co., Ltd.

: 1F, 7, Houde Street, Yonghe Dist. New Taipei City, 23455 Taiwan Signature

_________________________________ Name and Job Title.

: Paul Lai, CEO E-mail Tel.

: paul@asiarf.com

: 886229407880