Aperio AH20/AH30 Hub Installation Guide Experience a safer and more open world 1 AH20/AH30 - Table of Contents AH20/AH30 - FCC and ISED Canada Statements ............................................ 3 AH20/AH30 - Placement of Communication Hub ......................................... 5 AH20/AH30 - Mounting, Americas Adapter Plate .......................................... 6 AH20/30 - Mounting, Bottom Cover .................................................................. 7 AH20 (J101) - Connections ................................................................................... 8 AH20 Advanced Wiegand (J100) - Connections ..........................................10 AH20 - DIP Switch Configuration Table (S700).............................................11 AH30 (J101) - Connections ................................................................................12 AH30 - DIP Switch Configuration Table (S700).............................................13 AH30 - RS485 Bus Connection ...........................................................................14 AH30 - RS485 Addressing ....................................................................................15 AH20/AH30 - Communication Hub LED Indication ....................................17 AH20/AH30 - Technical Data ..............................................................................18 Conforms to EN 62368-1 and UL/CSA 62368-1 2 AH20/AH30 - FCC and ISED Canada Statements FCC Statements Changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
-
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Increase the separation between the equipment and receiver. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. ISED Canada Statements This radio transmitter [IC:9504A-AH20R03] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna type Internal antenna AH-ANTENNA-1 Maximum antenna gain (dBi) 3.6 2.15 Impedance (ohm) 50 50 3 This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-
exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le present metteur radio [IC:9504A-AH20R03] a t approuv par Innova-
tion, Sciences et Dveloppement conomique Canada pour fonctionner avec les types dantenne numrs ci dessous et ayant un gain admissible maximal. Les types dantenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour lexploitation de lmetteur. Gain dantenne maxima (dBi) 3.6 2.15 Type dantenne Antenne interne AH-ANTENNA-1 Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
Impdance (ohm) 50 50 4 AH20/AH30 - Placement of Communication Hub
< 25 m / ~ 80 ft AH20/30 - Placement of the Hub, 1 door Note: AH20/AH30 can be installed with an Aperio bottom cover or Americas adapter plate.
< 25 m / ~ 80 ft AH30 (RS485 Hub) - Placement of the Hub, 1-16 doors Note: AH20/AH30 must be installed into a junction box ex European 2-Gang, Aperio bottom cover or with Americas adapter plate to junction box. AH20/AH30 must be installed by qualified and trained personal. Indoor installation only!
5 AH20/30 - Mounting, Americas Adapter Plate
(US version) AH40 - Mounting, Americas Adapter Plate 1 3 5 2 Americas Adapter Plate Screw
(4 x 35 mm) 4 Screw
(3 x 10 mm) Option Top Cover External Antenna 6 AH40 - Mounting, Bottom Cover AH20/30 - Mounting, Bottom Cover (EU version) 1 Bottom Cover 2 Screw
(4 x 35 mm) Screw
(3 x 10 mm) Top Cover 3 Option External Antenna 7 AH20 (J101) - Connections S 1 0 0 1 2 3 4 J 1 0 0 EXT TERM NCL1 COM1 NOP1 NCL2 COM2 NOP2 NCL3 COM3 NOP3 NCL4 COM4 NOP4 12345678 OFF ON A 4 A 3 A 2 A 1 A 0 S 7 0 0 A B D1 D0 RED GREEN GND 8-24VDC INT J 1 0 1 AH20 Advanced Wiegand Connectors (J101) S 1 0 0 EXT TERM A 4 A 3 A 2 A 1 A 0 S 7 0 0 A B D1 D0 RED GREEN GND 8-24VDC INT J 1 0 1 AH20 Standard Wiegand Connectors (J101) Note: The installation must comply with national wiring regulations. 8 Communication Hub hardware version AH20 has four Wiegand signals plus power supply. The purpose and connection of these signals are described in the table below. Hub ConneCtor DesCription D1 D0 RED Wiegand Data 1 signal. Output from Communication Hub. Used to transmit credentials. Wiegand Data 0 signal. Output from Communication Hub. Used to transmit credentials. Wiegand Red LED signal. Input to Communication Hub. Used for access decision. Leave unconnected if DIP switch 1 is selected OFF. Signal is active low. GREEN Wiegand Green LED signal. Input to Communication Hub. Used for access decision. Signal is active low. See DIP 1 for alternate instructions. GND GND = Signal ground. Should be connected to EAC system GND and power supply GND. 8-24 VDC Power supply input, 8-24 VDC, 2 W (AH20 Advanced) alternatively 0.8 W (AH20 Standard and AH30). The power supply shall be 3 A over current protected. Wire requirements 16-22 AWG. 9 AH20 Advanced Wiegand (J100) - Connections S 1 0 0 1 2 3 4 J 1 0 0 EXT TERM NCL1 COM1 NOP1 NCL2 COM2 NOP2 NCL3 COM3 NOP3 NCL4 COM4 NOP4 12345678 OFF ON A 4 A 3 A 2 A 1 A 0 S 7 0 0 A B D1 D0 RED GREEN GND 8-24VDC INT J 1 0 1 AH20 Advanced Wiegand Connectors (J100) relays Relay 1 Relay 2 Relay 3 Relay 4 DesCription DPS (Door Position) RX (Request to exit) Battery Alarm Output Tamper Alarm Output/
Lock Jammed relay ContaCts DesCription NCL COM NOP Normally Closed Common Normally Open 10 AH20 - DIP Switch Configuration Table (S700) Dip switCH number label DesCription Controls use of Red LED signal for access decision. A0 ON => Red LED is used. OFF => Red LED is ignored. A1 Set to OFF by default. Reserved for future use. Controls addition of parity bits if required. ON => Addition of parity bits is enabled. OFF => Addition of parity bits is disabled. Credentials are transmitted as received. Controls byte order of transmitted credentials. ON => The byte order is reversed on the Wiegand interface compared to what is received from the Aperio lock. A2 A3 1 2 3 4 OFF => The byte order is left as is. Used in Pairing Mode. ON => Starts in pairing mode. 5 A4 OFF => Normal use. Note: If the DIP switch is moved from ON to OFF within 10 seconds from boot up and the Hub LED is lit, all paired devices will be unpaired. 6-7 8 INT/
EXT Not applicable (only used for AH30). Internal/External Antenna Use, ON = Internal 11 AH30 (J101) - Connections S 1 0 0 EXT EXT TERM TERM 12345678 12345678 OFF ON A A 4 4 A A 3 3 A A 2 2 A A 1 1 A A 0 0 S S 7 7 0 0 0 0 A B D1 D0 RED GREEN GND 8-24VDC INT INT J 1 0 1 AH30 (J101) Connectors Hub ConneCtor DesCription A B GND RS485 Data A. RS485 Data B. GND = Signal ground. Should be connected to EAC system GND and power supply GND. 8-24 VDC Power supply input, 8-24 VDC, 2 W (AH20 Advanced) alternatively 0.8 W (AH20 Standard and AH30). Note: The installation must comply with national wiring regulations. 12 AH30 - DIP Switch Configuration Table (S700) Dip switCH number label DesCription Controls RS485 addressing BIT 0-BIT 4. 1-5 A0-A4 ON => Address bit set. OFF => Address bit NOT set. 6-7 TERM See AH30 - RS485 Addressing Reference on page 13. Control use of termination resistor between RS485 A and RS485 B. For termination to be enabled, both switches must be set to ON. ON =>120 Ohm termination resistor connected/
enabled. OFF => 120 Ohm termination resistor disconnected/
disabled. Controls use of external antenna if required. 8 INT/EXT ON =>Selects use of internal antenna. OFF => Selects use of external antenna. 13 AH30 - RS485 Bus Connection Here are examples of connection of multiple Communication Hubs to a single RS485 bus of an EAC system. Termination should be enabled to the last Hub on the bus. A B EAC system Termination enabled A B Hub 1 DIP 6 OFF DIP 7 OFF A B Hub 1 DIP 6 ON DIP 7 ON A B Hub 2 DIP 6 OFF DIP 7 OFF A B Hub N End of Bus DIP 6 ON DIP 7 ON A B EAC system Termination enabled A B Hub 2 DIP 6 ON DIP 7 ON Communication Hub Connections, examples Note: The RS485 bus cable should be of type twisted pair. The maximum cable length of 1000 meters should not be exceeded. 14 AH30 - RS485 Addressing aDDress a0 a1 a2 a3 a4*
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Pairing Active*
ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON Address examples
*) Note: If any of the A0-A4 DIP switches are moved from OFF to ON within 10 seconds from boot up and the Hub LED is lit, all paired devices will be unpaired. 15 aDDress a0 a1 a2 a3 a4*
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON Address examples
*) A4 is only supported on AH30 in 1 - 1 mode. 16 AH20/AH30 - Communication Hub LED Indication The Communication Hub has a single LED that supports an optical scheme with red, green and yellow. The indication scheme is described by the two figures below:
Online Aperio Lock Offline EAC Offline Aperio Lock and EAC Offline UHF Communication Pairing Active Green Green + One Red Flash Green + Two Red Flashes Green + Three Red Flashes Yellow + Off, Fast Flash Yellow Note: With the software tool Aperio Programming Application and a USB radio dongle, further system installation parameters can be set. 17 AH20/AH30 - Technical Data Physical Dimensions Power Supply Power Rating Radio Standard Receiver Sensitivity Wireless Transmit Power Wireless Operating Range Internal Antenna External Antenna Operating Temperature Humidity IP Classification Safety, Radio and EMC 82 mm x 82 mm x 37 mm (H x W x T) 8-24 VDC The power supply shall be able to deliver minimum 2 W (AH20 Advanced) alternatively 0.8 W (AH20 Standard and AH30) and be 3 A over current protected. Wire requirements 16-22 AWG. IEEE 802.15.4 (2400 2483,5MHz) 16 channels (11-26) AES 128 bit encryption
-100 dBm 10 dBm/MHz. Peak value from average detector according to EN ETSI 300 328 Maximum spectral density. Indoors up to 25 m depending upon installed environment. Two cross polarized dipoles. One reverse polarity SMA external antenna connector. AH20/30 is certified to be used with ASSA ABLOY external antenna AH-ANTENNA-1. If other external antenna is used it must be of same type (dipole) and not have larger antenna gain than 3.6 dBi. 5 C to 35 C.
< 95 % non-condensing. IP20 IEC 62368-1:2014 EN 62368-1:2014 + A11:2017 UL/CSA 62368-1:2014 EN 301 489-1 V2.1.1 EN 301 489-17 V3.2.0 EN 300 328 V2.2.2 EN 50130-4:2011 + A1:2014 EN 62311 FCC 47CFR Part 15 subpart B and subpart C ISED RSS-247 and ICES-003 AS/NZS 4268 18 NOTE 19 www.assaabloy.com/aperio Experience a safer and more open world 20 1
-
1 7 3 2 4 0 1 0 0 D