Aperio Hub AH40 Installation Instructions ASSA ABLOY, the global leader in door opening solutions 1 AH40 - Table of Contents AH40 - FCC and Industry Canada Statements AH40 - Placement of Communication Hub AH40 - Connectors AH40 - Jumpers AH40 - Communication Hub LED Indications AH40 - Technical Data 3 4 5 6 7 8 ETL marking Recognized component 4002570 Conforms to ANSI/UL standard 294, ANSI/UL 60950-1 Certified to CAN/CSA standard C22.2 No. 60950-1 For more detailed information about the Aperio system please read ST-001279-Aperio Technology Installation Guide AH40. 2 AH40 - FCC and Industry Canada Statements This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
-
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Increase the separation between the equipment and receiver. This device complies with Part 15 of the FCC Rules and with RSS-210 of ISED. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
1. lappareil ne doit pas produire de brouillage, et 2. lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. The term IC: before the equipment certification number only signifies that the Innova-
tion, Science and Economic Development Canada technical specifications were met. Le terme IC devant le numro de certification signifie seulement que les spcifications techniques Innovation, Sciences et Dveloppement conomique Canada ont t respectes. FCC Caution: Any changes or modifications not expressly approved by the party respon-
sible for compliance could void the users authority to operate this equipment. This radio transmitter (IC: 9504A-AH40R02) has been approved by ISED to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna type: ASSA ABLOY AH-ANTENNA-1, max gain 2,15 dBi. Le prsent metteur radio (IC: 9504A-AH40R02) a t approuv par ISED pour fonctionner avec les types dantenne numrs ci-dessous et ayant un gain admissible maximal. Les types dantenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour lexploitation de lmetteur. Dantenne numrs: ASSA ABLOY AH-ANTENNA-1, Gain maximal indiqu 2,15 dBi. 3 AH40 - Placement of Communication Hub
< 15 m / ~ 50 ft Example of placement of the Hub with 8 locks. AH40 can manage up to 16 locks. Note: AH40 Communication hub must be installed into a junction box ex European 2-Gang, Aperio bottom cover or with Americas adaptor plate to junction box. AH40 must be installed by qualified and trained personal. Indoor installation only!
Note: The Aperio Communication hubs are not rated to be installed in the plenum space. 4 AH40 - Connectors ANTENNA EXT INT J201 LINK PAIR J321
- +
8-24V ConneCtors DesCription J201 J321 Ethernet connector. Connection to the Electronic Access Control system through a 10BASE-T / 100BASE-TX Local Area Network. Can also be used for power supply if connected to a IEEE 802.3af compliant Power Sourcing Device (PSE). Wire requirements CAT5 or higher. Power supply input, 8-24 VDC, 3.5 W. The power supply shall be a Limited Power Source (LPS) according to EN 60950-1. The power supply shall be 3 A over current protected. Wire requirements 16-22 AWG. Note: When PoE (Power over Ethernet) is used, no power supply should be connected to J321. The installation must comply with national wiring regulations. 5 AH40 - Jumpers ANTENNA EXT INT J201 LINK PAIR J321
- +
8-24V Jumpers DesCription ANTENNA Select external antenna by connecting the two left pins. Select internal antenna by connecting the two right pins. PAIR Select pairing mode by connecting the two left pins. Note: To install an external antenna use a thin screw driver and gently bend the antenna cap loose. Be careful, there are sensitive components behind the cap!
6 AH40 - Communication Hub LED Indications The Communication Hub has a status LED visible through the front cover. It supports optical schemes with red, green and yellow. The indication schemes are described by the figure below:
Online Aperio Lock Offline EAC Offline Aperio Lock and EAC Offline UHF Communication Pairing Active Green Green + One Red Flash Green + Two Red Flashes Green + Three Red Flashes Yellow + Off, Fast Flash Yellow Note: With the software tool Aperio Programming Application and an USB radio dongle, further system installation parameters can be set. ANTENNA EXT INT J201 LINK PAIR J321
- +
8-24V The LINK LED on the communication Hub indicates both status of the Ethernet Link level and if communication is ongoing. Note: LED on the Ethernet connector is not used. 7 AH40 - Technical Data Physical Dimensions 82 mm x 82 mm x 37 mm (H x W x T) Power Supply 8-24 VDC or Power over Ethernet (PoE) Power Rating Power supply The power supply shall be able to deliver minimum 3.5 W. The power supply shall be 3 A over current protected. PoE IEEE 802.3af compliant class 1 Powered device (PD) Ethernet 10BASE-T / 100BASE-TX Local Area Network Radio Standard IEEE 802.15.4 (2400 2483,5 MHz) 16 channels (11-26) AES 128 bit encryption Receiver Sensitivity
-100 dBm Wireless Transmit Power 10 dBm/MHz according to EN ETSI 300 328. Maximum spectral density. Wireless Operating Range Indoors up to 15 m / ~ 50 ft depending upon installed environment. Internal Antenna Two port cross polarized patch antenna. External Antenna Operating Temperature Humidity IP Classification Safety and Emissions One reverse polarity SMA external antenna connector. AH40 is certified and is only allowed to be used with ASSA ABLOY external antenna AH ANTENNA 1. 5 C to 35 C
< 95 % non-condensing IP20 FCC 47CFR Part 15 subpart B and subpart C IC RSS-GEN issue 5 IC RSS-247 issue 2 EN ETSI 301 489-1 v2.1.1 EN ETSI 301 489-17 v3.1.1 EN ETSI 300 328 v2.1.1 EN 60950-1:2006/A11:2009/A1:2010/A12:2011/
A2:2013 UL 294-2010 C22.2 8 NOTE 9 NOTE 10 NOTE 11 www.assaabloy.com/aperio ASSA ABLOY, the global leader in door opening solutions 12 S U
-
F
-
7 0 3 2 3 7 0 0 0 D