Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 1 (13) Author Susan Jansson ASSA ABLOY Installation of BLE Module 681402004 ASSA ABLOY HOSPITALTY AS. Author Susan Jansson Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 2 (13) Copyrights The information in this document is subject to change at the sole discretion of ASSA ABLOY Hospitality AS without notice. Any use, operation or repair in contravention of this document is at your own risk. ASSA ABLOY Hospitality AS does not assume any responsibility for incidental or consequential damages arising from the use of this manual. All information and drawings in this document are the property of ASSA ABLOY Hospitality AS. Unauthorized use and reproduction is prohibited. VingCard is a registered trademark of ASSA ABLOY Hospitality AS. ASSA ABLOY HOSPITALTY AS. Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 3 (13) Author Susan Jansson Installation of BLE Module 681402004 BLE Module 681402004 is only used in Assa Abloy Hospitality AS products. The BLE Module 681402004 is factory mounted in the Assa Abloy Hospitality AS products which in this document are referred to as The Host System. In addition, the BLE Module can be installed on Assa Abloy Hospitality AS existing installed products at our customers locations. These updates are solely carried out by Assa Abloy Hospitality Engineers. The customer or end user of the BLE Module have no contact with the Module as it is unseen to the end user so there are no special precautions the customer needs to take in terms of installing or usage of BLE Module 681402004. Each manual for the different Assa Abloy Hospitality AS end products, in which the BLE module 681402004 is installed, will contain the FCC and Industry Canada statements given below. FCC statements FCC (Federal Communications Commission) statements This device comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) The BLE Module may not cause harmful interference, and 2) The BLE Module must accept any interference received, including interference that may cause undesired operation. This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Important Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. This transmitter must not be co-located or operating in conjunction with any other antennas or transmitters. ASSA ABLOY HOSPITALTY AS. Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 4 (13) Author Susan Jansson Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The concerned end product must be labeled to say Contains FCC ID: Y7V-681402004 Industry Canada statements This device comply with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
1) The BLE Module may not cause interference, and 2) The BLE Module must accept any interference, including interference that may cause undesired operation of the device. Important note: To comply with Industry Canada RF radiation exposure limits for general population, the antennas used for these transmitters are exempted from Routine Evaluation Limits SAR Evaluation in accordance with RSS-102 section 2.5.1. The concerned end product must be labeled to say Contains IC: 9514A-68102004 Dclarations dIndustry Canada Cet quipement est conforme aux normes dexemption de licence RSS dIndustry Canada. Son utilisation est soumise aux deux conditions suivantes:
1) Le module BLE ne doit pas provoquer dinterfrence, et 2) Le module BLE doit accepter toute interfrence, y compris des interfrences susceptibles de provoquer un fonctionnement indsirable de lquipement. Remarque importante : Pour respecter les limites dexposition aux radiofrquences dIndustry Canada pour le grand public, les antennes utilises pour ces metteurs-transmetteurs sont exemptes des limites dvaluation de routine valuation SAR, conformment la norme RSS-102 section 2.5.1. Le produit final concern doit porter une tiquette avec la mention:
Contient IC: 9514A-68102004 ASSA ABLOY HOSPITALTY AS. Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 5 (13) Author Susan Jansson BLE Module 681402004 Installation Since the BLE Module 681402004 is not and will not be supplied to the end user on its own and the BLE Module 681402004 will only be installed and or replaced on the Host Systems by Assa Abloy Hospitality AS Engineers; only a quick generic installation guide of the BLE Module 681402004 to the Host System is given. Following parts are needed to connect BLE Module to the Host System ITEM NO. PART NUMBER DESCRIPTION QTY. 1 683081114 Y-Cable Zigbee Endnode 4825976 4825793 4825796 4825943 681402004 Classic Assy. Cable Sleeve Housing BLE Shield BLE Screw Standoff BLE Module 4826006 Host System label with information of installed BLE 1 1 1 1 2 1 1 2 3 4 5 6 7 ASSA ABLOY HOSPITALTY AS. Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 6 (13) Author Susan Jansson Installation Procedure Y-Cable Zigbee Endnode Classic Assy. and Cable Sleeve BLE Housing, Shield BLE, & Screw Standoff Interface to BLE Module 1) Y-Cable Zigbee Endnode 2) Cable Sleeve 3) Housing BLE 6) BLE Module Interfaces to the Host System 5) Screw Standoff 4) Shield BLE Insert the Cable Sleeve on the side of Y-Cable Zigbee Endnode Classic Assy. cable to be connected to the BLE Module. Thread the cable via the Shield BLE and Housing BLE; connect the Y-Cable to the BLE Module. Mount the BLE Module in the Housing, and cover it with the Shield. Mount the Screw Standoff. ASSA ABLOY HOSPITALTY AS. Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 7 (13) Author Susan Jansson A mounted BLE Module in the housing and Y-Cable connected To Host System BLE Module with Y-Cable connected and Screw Standoff mounted, covered by the BLE shield. Thread the rest of Y-cable which will go to the Host System through the door, alien the Screw standoff, connected the Y-cable to the appropriate connectors on the Host system. Y-Cable connected to the Host System Battery pack 4.5V ASSA ABLOY HOSPITALTY AS. Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 8 (13) Author Susan Jansson 7)Host system label concerning BLE The Host System label indicating the presence of the BLE module in the system should be attached as indicated:
Host Label indicating the presence of BLE module with FCC and IC Identification Installed the Back Host System cover Front Host system Back Host System Cover ASSA ABLOY HOSPITALTY AS. Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 9 (13) Author Susan Jansson BLE Module Replacing Procedure The only tool need is Screwdriver Torx T20S for removing the screws on the Host System. Remove the Host System Cover. Disconnect the Y-Cable connectors (coming from the BLE module) from the Host System, and remove the Host System screws connected to BLE module item 5: Screw standoff. Screws connected to BLE Module Screw standoff. Y-Cable connected to the Host System ASSA ABLOY HOSPITALTY AS. Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 10 (13) Author Susan Jansson From the front side of the Host system, pull out the unit where BLE module is mounted. Unmount the BLE shield. Unmount the BLE shield Disconnect the Y-cable from the BLE Module Remove the BLE Module from the BLE housing and replace it. ASSA ABLOY HOSPITALTY AS. Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 11 (13) Author Susan Jansson Viewing FCC an IC information label on the Host System All Host Systems where a BLE Module is installed; has an attached label with FCC and IC identities. To gain access to this label once the module has been installed in the Host System, the only tool need is a Torx T20s screwdriver, which is readily available from any hardware store. Following procedure should be followed to gain access to the label:
The Host System Back Host System Use Torx T20s screwdriver and open the Host System Back cover to access the label Front Host System ASSA ABLOY HOSPITALTY AS. Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 12 (13) Author Susan Jansson After opening the Back Cover, the Label can be accessed Label on the Host with following statements:
Contains FCC ID: Y7V-681402004 Contains IC: 9514A-68102004 Open with Torx T20s screwdriver BLE Module 681402004 Operation BLE Module 681402004 operates only on Assa Abloy Hospitality Host Systems, and is solely installed, maintained, and debugged by Assa Abloy Hospitality Engineers. BLE Module Specifications Radio technologies utilized BLE [Bluetooth low energy]
Frequency ranges of operation 2.400 GHz-2.4835 GHz Channel plan Transmitter antenna gain Antenna Type Maximum expected conducted power Operating Temperature Operating humidity Power supply requirements 40 2-MHz channels 3.5dBi, Impedance 50 ohm Inverted F-antenna (internal PCB) 2.51mW
-10O C to +50O C 10% to 90% non-condensed relative humidity
+6VDC -5% - +50%
ASSA ABLOY HOSPITALTY AS. Title Installation of BLE Module 681402004 Category Installation of BLE Module Document number 69 1402 012 Revision 8 Type Date 20150302 Page (of) 13 (13) Author Susan Jansson Overview functionality of the BLE Module When a BLE Module comes from the production, it will be in an advertise mode that is always searching for another BLE device. In a hotel environment the BLE Module is set in dormant mode and it will search for a BLE device when the Host System tells it to go out and search. When the BLE Module has found a BLE device and started the handshake, the communication between the BLE Module and the BLE device starts, they share information between them and the door opens, then the Host System tells the BLE Module to go to sleep. If the BLE Module doesn't find any device to do the handshake with, the Host System tells it to go down to sleep and stays in sleep until the Host System tells it to start searching for BLE devices. ASSA ABLOY HOSPITALTY AS.