FCC ID: Y7V-LCX7301C1 Door lock with 906MHz Radio Module

User Manual VingCard DLC1 FCC (Federal Communications Commission) statements This device comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) The product LCX 7301 may not cause harmful interference, and 2) The product LCX 7301 must accept any interference received, including interference that may cause undesired operation. Important note: To maintain compliance with FCCs RF exposure guidelines, this equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. Use only the supplied antenna. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antennas or transmitters. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. 2 66 5013 157-0 IC (Industry Canada) statements This device comply with Industry Canada licence-exempt RSS standard CAN ICES-3 (B)/NMB-3(B) B. Operation is subject to the following two conditions:

1) The product LCX 7301 may not cause interference, and 2) The product LCX 7301 must accept any interference, including interference that may cause undesired operation of the device. Important note: To comply with Industry Canada RF radiation exposure limits for general population, the antennas used for these transmitters are exempted from Routine Evaluation Limits SAR Evaluation in accordance with RSS-102 section 2.5.1. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. The product LCX 7301 IC: 9514A-LCX7301C1 has been approved by Industry Canada to operate with the antenna type listed below with the indicated maximum permissible gain and required antenna impedance. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Name/Model F-antenna Gain 2.33 dBi Impedance 50 ohm The term "IC" before the equipment certification number only signifies that the Industry Canada technical specifications were met. Dclarations dIndustry Canada Cet quipement est conforme aux normes dexemption de licence RSS dIndustry Canada CAN ICES-3 (B)/NMB-3(B) B. Son utilisation est soumise aux deux conditions suivantes:

1) Le produit LCX 7301 ne doit pas provoquer dinterfrence, et 2) Le produit LCX 7301 doit accepter toute interfrence, y compris des interfrences susceptibles de provoquer un fonctionnement indsirable de lquipement. Remarque importante: Pour respecter les limites dexposition aux radiofrquences dIndustry Canada pour le grand public, les antennes utilises pour ces metteurs-transmetteurs sont exemptes des limites dvaluation de routine valuation SAR, conformment la norme RSS-102 section 2.5.1. Conformment aux rglementations dIndustry Canada, cet metteur radio peut uniquement fonctionner laide dune antenne dont le type et le gain maximal (ou minimal) pour ces metteurs-transmetteurs sont approuvs par Industry Canada. Pour rduire le risque d'interfrence ventuelle pour les autres utilisateurs, le type et le gain de l'antenne doivent tre choisis de manire ce que la puissance isotrope rayonne quivalente (p.i.r.e.) ne soit pas suprieure la puissance ncessaire une bonne communication. Ce produit LCX 7301 IC: 9514A-LCX7301C1 a t approuv par Industry Canada pour une utilisation avec les types dantenne indiqus ci-dessous avec le gain maximum autoris indiqu et limpdance dantenne requise. Il est strictement interdit dutiliser avec cet appareil un type dantenne ne figurant pas dans cette liste ou ayant un gain suprieur au gain maximum indiqu pour ce type. Appellation/Modle Antenne Gain 2.33 dBi Impdance 50 ohm Le terme IC devant le numro de certification de lquipement signifie seulement que les spcifications techniques dIndustry Canada ont t respectes. 3 66 5013 157-0 Successful opening Find your room. Touch the handle (green light). Enter the room. Unsuccessful opening Touch the handle (red light). Contact the reception. Find your room. 4 66 5013 157-0 5 66 5013 157-0

13.03.2019 Nemko Canada Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Nemko A/S, Instituttveien 6, N-2007 Kjeller, Norway, to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by Nemko Canada Inc, still resides with, ASSA ABLOY Global Solutions AS Dated this Agency agreement expiration date:

By:

Bjrn Kolstad 13 March 2020 of March 20 19 13th Signature Title: Manager Test Lab On behalf of :

ASSA ABLOY Global Solutions AS Telephone: 004769245000 Printed

EXTERNAL PHOTOS Project no.: 357459 FCC ID: Y7V-LCX7301C1 Page 1 (6) EXTERNAL PHOTOS LCX7301 Picture 1. Complete unit mounted on a door (inside). EXTERNAL PHOTOS Project no.: 357459 FCC ID: Y7V-LCX7301C1 Page 2 (6) Picture 2. Complete unit mounted in a door (outside). EXTERNAL PHOTOS Project no.: 357459 FCC ID: Y7V-LCX7301C1 Page 3 (6) Picture 3. Lock case without plastic cover. EXTERNAL PHOTOS Project no.: 357459 FCC ID: Y7V-LCX7301C1 Page 4 (6) Picture 4. Lock case without plastic cover (more detailed). EXTERNAL PHOTOS Project no.: 357459 FCC ID: Y7V-LCX7301C1 Page 5 (6) LCX7301 module with complete door PHOTOS OF ACCESSORIES EXTERNAL PHOTOS Project no.: 357459 FCC ID: Y7V-LCX7301C1 Page 6 (6) 3.2Vdc rechargeable battery

INTERNAL PHOTOS Project no.: 357459 FCC ID: Y7V-7301C1 Page 1 (2) INTERNAL PHOTOS LCX7301 Front view INTERNAL PHOTOS Project no.: 357459 FCC ID: Y7V-7301C1 Page 2 (2) Rear view

. Y O L B A A S S A f i o n o s s m r e p i e h t t u o h t i i w d e s c r e x e e b t h g i r e v s u c x e l i r e h o t y n a y a m r o n

, s s e c o r p y n a y b

, d e c u d o r p e r e b y a m t r a p o n d n a t h g i r y p o c s i k r o w s h T i 1 1 1 All text:

Font Verdana Height: 0,8mm IEEE text:

Font Verdana Height: 0,7mm 5

, 0 7,3 Bold text 0,5 3

, 7

, 5 5 1 7

. i n M 5

. i n M 13 24,5 0,5 5

, 0 Label is made using the LCX test equipment The IEEE number is printed by the test equipment Legend:

P000989920-001-001 = ASSA ABLOY Hospitality's product number R = Current revision YY = Year (Last two digits) WW = Week number MMM = Manufacturer's alphabetic code (Specified by ASSA ABLOY Hospitality from the file Manufacturer codes.doc) NNNNN =Serial number.(Starts on 00001 every Monday) CCCCC = Country of manufacture Bar code:

Standard Data Matrix Physical size: 7,3 mm x 7,3 mm Bar code content:

P000989920-001-001 R YYWW MMM NNNNN Example of bar code content:

P000989920-001-001 B 1737 HA 00487 Label requirements:

The label must be indelible and legible. The marking shall not be removed or the label shall not come loose when rubbed lightly with a piece of cloth soaked in petroleum, spirit or water. General Table Product number Rev P000989934-001-001 B REVISIONS Sign. Surface:

Volume:

Weight:

38.00 0.04 Surface area:

767.56 ASSA ABLOY Hospitality AS Description Initial drawing Updated text Added IEEE number P-rev. D-rev. Date 1 2 3 31.05.2018 06.08.2018 17.01.2019 A B Material:

MD003-026B for UL File MH46084 1M MAT CH PET TC/S-8005 for UL File MH20558 Designed by:

c-harves Drawn by:

c-harves Created (YYYY-MM-DD):

2018-05-31 Label LCX label General tolerance:

ISO 2768-vL Scale:

5:1 (A4) Alternate ID Projection:

Approved 2019-02-11 Configuration:Default Document ID D000989934-001 Rev.:

3 SHEET 1 OF 1 5 1

7 0

6 1 0 2 _ 5 V