Studio Broadcast System bp24 SET UP and USE Studio Broadcast System 1. REGULATORY AND COMPLIANCE STATEMENTS ............................................................................................................ 3 2. OVERVIEW 2.1 Core Performance Targets 2.2 Specifications 2.3 System Components 2.4 System Block Diagram 3. BP24 UWB BODY PACK TRANSMITTER ........................................................................................................................... 4. RP32 UWB RECEIVER MODULE ....................................................................................................................................... 5. MCU3224 MAIN CONTROL UNIT ..................................................................................................................................... 4.1. FRONT PANEL ........................................................................................................................................................................................... 4.2. REAR PANEL ............................................................................................................................................................................................. 6. GUI INTERFACE ............................................................................................................................................................... 5.1. HOME SCREEN .......................................................................................................................................................................................... 5.2. TRANSMITTER DETAIL SCREEN ...................................................................................................................................................................... 5.3. MATRIX SCREEN - RECEIVER MEASUREMENT ................................................................................................................................................... 5.4. MATRIX SCREEN TRANSMITTER MEASUREMENT ............................................................................................................................................. 5.5. SETUP SCREEN .......................................................................................................................................................................................... 7. QUICK START ............................................................................................................................................................... Page 2 of 26 Studio Broadcast System 1. REGULATORY AND COMPLIANCE STATIC HAZARD. Opening this unit is likely to cause permanent performance malfunction. Evidence of opening will void warranty. Serviceable only by Audio-Technica. Contact Audio-Technica for return authorization should service be necessary. Page 3 of 26 Studio Broadcast System 2. Overview 2.1 Core Performance Targets STUDIO BROADCAST Operating Method UWB OOK Center frequency 6.500GHz Simultaneous Receive Points Simultaneous Transmitters 32 24 Audio Dynamic Range 24 bits Frequency Response 20Hz -20kHz Latency
<3 mS Analog to Digital out Audio Interface MADI/DANTE External Control Interface USB/Ethernet User Interface Touchscreen GUI Battery Life 5 hours Range (single RP line of sight) 90 feet Page 4 of 26 2.2 Specifications Studio Broadcast System Overall System Dynamic Range Total Harmonic Distortion
>109 dB (A-weighted, typical)
<0.06% (-40dBV input level) BP24 Specs (inherent to beltpack / Direct connect Self Noise @ 0dB gain Self Noise @ 20dB gain Sensitivity @ 0dB gain Sensitivity @ 20dB gain Dynamic Range SNR @ 0dB gain SNR @ 20 dB gain Maximum Input Level (5% THD) Total Harmonic Distortion Operating Frequency Range Tx Output Power Modulation Emissions Designator
-111dBA
-106dBA
-44dBV
-23dBV 111dB (A-weighted, typical) 67dBA 82dBA 4.8dBV
<0.06% (-40dBV input level) 6250MHz 6750MHz 2nW mean none 500MN1W Page 5 of 26 Studio Broadcast System BP24 w/ AT899cL4 or cL4SW mic Self-Noise @ 0dB gain Self-Noise @ 20dB gain Sensitivity @ 0dB gain Sensitivity @ 20dB gain Dynamic Range SNR @ 0dB gain SNR @ 20dB gain Frequency Response Impedance DC current Battery Battery life
-109dBA
-93dBA
-48dBV
-28dBV 109dB (A-weighted, typical) 61dBA 65dBA 20Hz 20,000Hz 250 ohms 1.7mA 2 x AA 5 hours MCU3224 Frequency Response Input/Output Connections 20Hz 20,000Hz MADI 2 x 75 ohm BNC to coax, 2 x multimode fiber DANTE 2 x RJ45 Receivers 32 x 12 V, RJ45 Black burst 1 x BNC
@ 33 ohm load Headphone/Monitor Out Total Harmonic Distortion <0.1%
Noise -90dBV Maximum Output Power 200mW Power Redundant AC supply 2 x 110-240V, 50-50Hz, 420W max Cable 2 x IEC Page 6 of 26 Studio Broadcast System 2.3 System Components Model BP24 RP32 MCU3224 AT899cL4 or cL4SW Description Body Pack Transmitter with Talkback Function UWB Receiver and Antenna Module Main Control Interface Unit (3U) Microphone Microphone with Inline Talkback Switch 2.4 System Block Diagram Network Control
(Future) Ethernet Mains In (Red) Mains In (Blue) RX 1
. Wireless Links
(TDMA) RX 32 TX 1
.
`
TX 24 Cat 5 - All RX Home Run to Main Control Unit
. x32 MAIN CONTROL INTERFACE UNIT
(3U) 7 TOUCH SCREEN GUI
(on-board) Page 7 of 26 x24 Dante 1 Dante 2 BNC-Audio Word Clock In Word Clock Out Fiber In Fiber Out Network Audio Dante
(Future) Ethernet MADI 75 co-ax MADI Fiber (GBIC) Audio CH 1-8 FUTURE Analog Break Out Audio CH 9-16 Audio CH 17-24 Box x8 Or AES 3 Outputs FUTURE Analog Break Out Box x8 Or AES 3 Outputs FUTURE Analog Break Out
(Future) Box x8 Or AES 3 Outputs Studio Broadcast System 3 BP24 UWB Body Pack Transmitter 3.1 Transmitter Controls An On/Off power switch is located in the battery compartment. The adjustable transmitter parameters are:
1. System ID (SYS) Each transmitter must be assigned a system ID (1-9) that must match the system ID set on the MCU3224 The transmitter will only transmit when it receives a sync pulse and matching system ID from an active system. This will prevent users with transmitters assigned the same channel slot on a different system from interfering if they enter the coverage area. Note: RP timing signals from separate systems must be RF isolated from one another to prevent system timing contention in transmitters. 2. Channel Number (CHAN) The channel slot assigned to the transmitter (01-
24.) Each transmitter in the system is assigned a unique channel number. 3. Input level (GAIN) Adjustment of the audio input level (0 dB to 20dB in 2dB Steps). The adjustable transmitter parameters are shown on a display located on the face of the transmitter. The display will only be illuminated when the user is adjusting the transmitter. Pressing any button will activate the display for 10 seconds. After 10 seconds, display functions will no longer be illuminated although the BP is functioning. Pressing any button will light the display in order to check for power or operating condition. Page 8 of 26 Studio Broadcast System Parameter Selection System ID Channel Up/Down Keys Input Level Adjustment Process:
1. Press and Hold (2 sec) the button associated with the parameter to be adjusted - SYS, CHAN or GAIN. 2. The selected parameter value will flash on the screen. 3. Make the adjustment via the up down arrow keys. 4. The new value will be shown 5. Confirm the change by pressing the same parameter button as step 1. 6. The changed value will flash twice indicating the parameter change. Note: If there is no button pressed for a 10 second period the transmitter will revert to its original settings and the display will go dark. Note: No parameter changes will be made unless confirmed as indicated in step 5 above. Pressing a different parameter selection button, or allowing a 10 second period without any input abandons any change in process. Note: GAIN value is automatically sent to and adjusted at the MCU3224 display. BP GAIN setting may also be changed via MCU3224 transmitter detail screen Page 9 of 26 SYSTEM ID SYSTEM ID 3.2 Batteries Studio Broadcast System The BP24 operates via 2 x AA size batteries. When inserting the batteries into the BP24, observe correct polarity as marked. Do not peel off or damage the outer tube of the battery. Do not use a leaking battery. If battery leakage occurs, avoid contact with skin. If contact occurs, immediately was thoroughly with soap and water. If battery leakage comes into contact with your eyes, immediately flush with water and seek medical attention. Do not expose batteries to fire. Do not heat, deform, solder, disassemble or modify batteries. For best operation, do not use batteries of different types together, old or new batteries together, or batteries with different charge levels. 3.3 Transmitter Audio Output Routing The system includes a talkback function utilizing 48 output channels in either the MADI stream or DANTE/AVB network output. In normal operation, audio will be routed to the audio channel that matches the channel slot number assigned (Audio Channel = CHAN =
1 - 24). The talkback function is activated by connecting the appropriate transmitter connector contact (TBD) to ground when the in-line talkback switch is depressed. The talkback function is a press and hold operation. While the talkback button is depressed, the audio output will be routed to a channel in the range of 25 to 48 - equal to the channel slot number + 24 (Audio Channel = CHAN +24). Upon button release, the audio channel returns to the normal operation on the assigned channel 1-24. Page 10 of 26 Studio Broadcast System 4 RP32 UWB Receiver Module Receiver Front View Receiver ID Number A two digit display (7 Segment LED) is provided to automatically indicate the receiver channel number when the RP32 is connected via a CAT5 cable to the corresponding output channel of the MCU3224. This display serves as the units power indicator. A visible channel number also indicates that there is a full round-trip connection between the RP and the MCU communications, confirming that the cable, the RP and the corresponding MCU3224 channel are all operating appropriately. Should the user prefer that the LED lights not be illuminated, there is a control option available on the MCU tools screen which allows this RP display lights to be turned off. Page 11 of 26 Studio Broadcast System Receiver Rear View RJ45 Connector for Cat5 Cable Connection to the RP32 is via an RJ45 jack on the rear. Once connected via RJ45 and shielded CAT5 cable to an MCU, the RP is operational. There is no power switch, and no further controls necessary. The MCU3224 supplies operating power and control over RP functions/preferences is available via the tools screen of the MCU3224. A choice of 2 mounting threads are available on the rear of the RP32. The inserts mate with either 5/8-27 thread or -20 thread adapters. Page 12 of 26 5 MCU3224 Main Control Unit Studio Broadcast System The main control unit is the central connection and control point for the system. It also supplies the power required to operate up to 32 receivers via standard shielded CAT 5 cable. This unit provides operational coordination, regulates system timing and feeds the output product to the end users system as desired. The MCU allows user control/adjustment of operating preferences and management of both transmitters and receivers. The audio outputs - MADI, Networked Audio Protocal are all contained within this 3U sized unit, with appropriate output connections on the rear. A touchscreen GUI, and internal headphone monitor output/meter are provided for user control and monitoring. The MCU3224 operates via 2 fully redundant 110-220V 50-60Hz AC power supplies via 2 separate standard IEC power cables. The unit is fully operational with a single power cable and power supply. A front panel display will indicate a blue light for the 1st power supply and a red light for the 2nd power supply. Headphone Jack and Front Panel Level Control Touch Screen GUI (7 Color) On/Of f Red and Blue Power Lights Page 13 of 26 Studio Broadcast System The Front Panel design has minimal controls; the majority of Monitoring and control are handled through the touchscreen GUI. If a channel is selected using the GUI its audio will appear at the headphone jack and VU meter. Rear Panel Networked Audio Connections MADI Fiber GBIC Coax Word Clock In Coax - Word Clock Out Coax - Audio RS232 programming Port 32x Receiver Connections Blackburst Input Ethernet
(Future) Break Out Box Connections Analog CH 01-08 or AES 3 Analog CH 09-16 or AES 3 Analog CH 17-24 or AES 3
(Future) Mains
(Redundant) 6 GUI Interface Page 14 of 26 The GUI interface is divided into four screens:
Studio Broadcast System Home Screen This screen will display an overview of all 24 transmit channel slots at once. The user will be able to select the active channel on this screen by tapping the corresponding channel tile. The audio from the active channel will be sent to the headphone monitor output. Transmitter Detail Screen Activating this screen will display more detailed information about the status of the active channel, including battery information and connection history. Matrix Screen This screen is used for system set up, coverage confirmation and detailed debugging of receivers and transmitter links. System Setup This screen contains the basic system set up parameters. Dante, and MADI set up information, Ethernet IP Address, System ID etc The letter in the center indicates the System ID. Page 15 of 26 Studio Broadcast System 6.1 Home Screen Channel Monitoring Screen Navigation Buttons Yellow = Active System ID Inactive Channel Critical Battery Selected Channel Receiver Links Battery Gauge Receiver Link Indicators tell the user how many receivers are currently linked to the transmitter
(1, 2, or 3+.) This is a very good indicator of the strength of the transmitters current UWB link BER Meter Channel Page 16 of 26 6.2 Transmitter Detail Screen Studio Broadcast System The detail screen gives the user a view of the all transmitter information in one place;
including a history of the transmitters link status, and battery use details. BER METER RECEIVER LINK HISTORY TIME BASE FOR RECEIVER LINK CHART Transmitter Audio Input Level Battery Fuel Gauge Battery Time Left CHANNEL NUMBER The receiver link chart shows the history of the transmitter link status over the timer scale selected (2 to 60 Min). Each bar indicates the minimum number of receivers the transmitter is linked to. If the link is dropped, a red mark shows the time when it happened. Page 17 of 26 Critical Battery Studio Broadcast System The user will be able to control the transmitter audio input level from this screen. The user may press either the up or down arrow to select the desired gain setting. This action will cause the new value to be displayed (in red) and a Set button will appear. The setting is not changed on the transmitter until the set button is pressed. Activating another function on the GUI or allowing a 10 second interval without interaction will abandon the change. Once the set button is pressed, the system will send a command to the transmitter to change the setting. When the transmitter acknowledges the change, the set button will disappear, and the setting color will change back to white. Note: When the transmitter is not in link this option will not be available. If the transmitter does not acknowledge the change after several attempts, an error message will be displayed and the setting will revert to the previous setting. This would only happen if the transmitter moved out of the coverage pattern during the change process. 6.3 Matrix Screen - Receiver Measurement The matrix screen allows the user to visualize specific connections between 32 possible receivers and 24 possible transmitters. There are two modes: Receiver Test and Transmitter Test. In the receiver test mode the user selects a source transmitter - blue buttons on the right side of the screen - and the screen on the left indicates the active receivers currently linked to that transmitter. Active receivers are indicated with a blue square;
green fill indicates a link to the selected transmitter. Page 18 of 26 Studio Broadcast System Mode Swap Button Mode Select The button is used to view receivers that are connected to ANY active transmitter rather than just a single transmitter. This mode is used to test which receivers are most effective in a given set up, and may assist in receiver placement. When the user selects the matrix screen, the system will first check for added receivers;
without interrupting the operation of the active receivers or the audio output. This gives the user a way to add receivers while the system is in active operation. If the user plugs in a receiver it will not be active until the system goes through this process. Pressing the mode swap button switches to Transmitter measurement mode. Page 19 of 26 Studio Broadcast System 6.4 Matrix Screen Transmitter Measurement In the transmitter measurement mode the user selects one of the active receivers blue buttons on the right side of the screen - and the transmitters linked to that receiver are indicated on the left side of the screen.
-mode operation is similar - when selected, the system will show transmitters that are connected to any receiver in the system. This is a quick way to make sure that all transmitters are connected to the system by at least one receiver. Page 20 of 26 6.5 Setup Screen User TOOLS Studio Broadcast System The setup screen allows the user to monitor certain key system performance values or settings, and allows system parameters and operation values which may be determined by user preferences. Monitor and control includes:
IP Address for the network adaptor DHCP Dante/AVB Sync precision System ID (1-9) Reference Clock Source and BLACK BURST sync match
(precision) RP display (on/off) control Battery fuel gauge time to empty warning alert setting preference Page 21 of 26 Studio Broadcast System Test Mode activates a test tone through the system so that the user can carry out a constant-signal walkout test while setting up and de-bugging the system. NOTE: No normal audio operation is available when in the test tone mode, and the mode must be exited in order for the system to operate normally. To enter and activate any of the TOOLS screen functions, press on the screen graphic for the desired parameter. The display for the selected parameter will blink. Press the SET button on the number pad to confirm the change. To enter TEST MODE, press on the screen graphic at the OFF position under test mode. The parameter will begin to blink. Enter the Audio-Technica phone number using the key pad by pressing 330 686 2600 and then press SET. The display for TEST MODE will now change to a green color and display ACTIVE. To immediately stop the TEST TONE, press on the screen where it says OFF. 7. QUICK START Using a shielded CAT 5 cable (may be used with up to 1,000 feet of cable per channel) terminated with a standard RJ45 connector, plug the cable into the RJ45 input jack on the rear of at least one RP32 receiver. Connect the other end of the CAT 5 cable to the RJ45 input jack on the rear of the MCU3224 main control unit. You may connect up to 32 RP32 receivers by connecting them into the corresponding channel output (1-32) found on the rear of the MCU. You do not need to turn the RP on. It receives power via the CAT 5 cable from the MCU 3224. The RP display should immediately light and display the channel output number to which it has been connected on the MCU. Apply power to the MCU3224 by connecting at least one IEC cable to AC wall supply. Page 22 of 26 Studio Broadcast System Turn on one or both of the IEC power switches on the rear of the unit. The unit fan will begin operation. Press the front panel power button. The power light(s) corresponding to the IEC cable input will be visible on the front panel (one red and one blue), and the GUI screen will illuminate and enter a set-up mode while the system is normalizing and preparing for operation. Once the system is available for operation, the GUI screen will display a HOME SCREEN. On the left-hand side of the screen, select the Matrix button:
This will allow the user to view and confirm that the desired number of RPs are connected to the system with the desired channel # assignments. Place 2 x AA batteries into a BP24 beltpack transmitter and slide the internal power switch into the on position. Page 23 of 26 Studio Broadcast System Ensure that the BP24 system ID is the same as the System ID of the MCU3224 (system will turn on in default system ID 1 for all devices). The System ID is visible in all screens on the left-hand side of the display for navigation. Select the BP24 channel for operation (1 through 24) Select the desired BP24 gain level Ensure that the BP24 front surface is facing the RP32 front surface, and that they are located somewhat in proximity to each other and roughly in a line-of sight orientation. (Note that the distance of operation can be 90 or more, depending upon the particular operating environment, and line of sight operation is not strictly or fully required due to positive effects of multi-path. However, with only a single RP connected to the system, the multiple coordinated receiver diversity is not in operation. Thus, line of sight and proximity are more important to stable operation for initial set-up with only a single RP). Page 24 of 26 Studio Broadcast System Return to the MCU and select the home screen The BP24 that has just been turned on should be shown in the display on the channel number that you have set via the BP24 channel selection process. Press the GUI on the displayed channel to highlight/select the channel of the BP24 that you are operating. This will allow all information about this particular channel to be observed on the other screens. It also selects this particular channel for output to the front-mounted headphone monitor jack. You may now listen to your selected beltpack, or if you prefer, you can observe its operation characteristics by selecting the transmitter detail button:
Repeat this process for as many RP32s and BP24s as needed for the application. No frequency or channel coordination is required. Simply ensure that only one beltpack channel is in operation for each channel (up to 24) in each system ID. (Do not attempt to set 2 BP channels to the same channel # in the same system. The system will not operate). Page 25 of 26 Studio Broadcast System Page 26 of 26