all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 917.49 KiB | May 12 2014 | |||
1 | External Photos | May 12 2014 | ||||||
1 | Cover Letter(s) | May 12 2014 | ||||||
1 | RF Exposure Info | May 12 2014 | ||||||
1 | Test Report | May 12 2014 | ||||||
1 | Cover Letter(s) | May 12 2014 | ||||||
1 | Test Setup Photos | May 12 2014 | ||||||
1 | Internal Photos | May 12 2014 | ||||||
1 | ID Label/Location Info | May 12 2014 | ||||||
1 | ID Label/Location Info | May 12 2014 |
1 | User Manual | Users Manual | 917.49 KiB | May 12 2014 |
System 10 PRO Digital Wireless System Installation and Operation ATW-1301 UniPak Transmitter System ATW-1301/L Lavalier Microphone System ATW-1302 Handheld Microphone System ATW-1311 Dual UniPak Transmitter System ATW-1311/L Dual Lavalier Microphone System ATW-1312 UniPak/Handheld Combo System ATW-1312/L Lavalier/Handheld Combo System ATW-1322 Dual Handheld Microphone System 2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE. CERTIFICATION: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. THIS DEVICE COMPLIES WITH INDUSTRY CANADA LICENSE-EXEMPT RSS STANDARD(S). OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Cet appareil est conforme la/aux norme(s) CNR exempte(s) de licence dIndustrie Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer dinterfrence et (2) cet appareil doit accepter toutes les interfrences, y compris celles susceptibles de provoquer un fonctionnement non souhait. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. WARNING: Changes or modifications not expressly approved in writing by Audio-Technica may void the users authority to operate this equipment. RF Exposure Statement: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter used in other systems. The ATW-T1001, ATW-T1002 and ATW-RU13 complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation. (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from persons body. Le ATW-T1001, ATW-T1002 et ATW-RU13 conformes aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre conforme sans valuation de l exposition maximale autorise. Cependant, il est souhaitable qu'il devrait tre install et utilis en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps. Note: The ATW-RC13 has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-
-
-
-
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil umerique de la classe B est conforme a la norme NMB-003 du Canada. CAUTION! Electrical shock can result from removal of the receiver chassis cover. Refer servicing to qualified service personnel. No userserviceable parts inside. Do not expose to rain or moisture. The circuits inside the chassis, receivers and transmitters have been precisely adjusted for optimum performance and compliance with federal regulations. Do not attempt to open the chassis, receivers or transmitters. To do so will void the warranty, and may cause improper operation. Notice to individuals with implanted cardiac pacemakers or AICD devices: Any source of RF (radio frequency) energy may interfere with normal functioning of the implanted device. All wireless microphones have low-power transmitters (less than 0.05 watts output) which are unlikely to cause difficulty, especially if they are at least a few inches away. However, since a body-pack mic transmitter typically is placed against the body, we suggest attaching it at the belt, rather than in a shirt pocket where it may be immediately adjacent to the medical device. Note also that any medical-device disruption will cease when the RF transmitting source is turned off. Please contact your physician or medical-device provider if you have any questions, or experience any problems with the use of this or any other RF equipment. Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other Install in accordance with the manufacturers instructions. apparatus (including amplifiers) that produce heat. 9. Unplug this apparatus during lightning storms or when unused for long periods of time. 10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Thank you for choosing an Audio-Technica System 10 PRO Rack-Mount digital wireless system. You have joined thousands of other satisfied customers who have chosen our products because of their quality, performance and reliability. This wireless microphone system is the successful result of years of design and manufacturing experience. Audio-Technicas System 10 PRO Rack-Mount is a digital wireless system designed to provide rock-solid performance along with easy setup and clear, natural sound quality. Featuring a dual-receiver chassis and remote-mount receiver unit capability, System 10 PRO Rack-Mount is available in various handheld and body-pack configurations. Operating in the 2.4 GHz range, far from TV and DTV interference, System 10 PRO Rack-Mount offers extremely easy operation and instantaneous channel selection. Up to ten channels may be used together without any frequency coordination problems or group selection issues. System 10 wireless ensures clear communications by providing three levels of diversity assurance: frequency, time, and space. Frequency Diversity sends the signal on two dynamically allocated frequencies for interference-free communication. Time Diversity sends the signal in multiple time slots to maximize immunity to multi-path interference. Finally, Space Diversity uses two antennas on each transmitter and receiver to maximize signal integrity. Each configuration of the System 10 PRO digital wireless system includes a rack-mountable receiver chassis with two receiver unit docks. Depending on the configuration, the system will also include one or two receiver units that may be docked in the chassis or mounted remotely, and one or two transmitters of either the handheld microphone or body-pack style (or one of each). Some configurations also include one or two lavalier mics that attach to the body-pack transmitters. Up to five chassis (10 receiver units) can be linked with the included RJ12 cable to allow for simultaneous use of all receivers and increased stability of the multi-channel system. Because System 10 packaging is designed to hold all versions of the system, some compartments in the carton may be intentionally left empty. The ATW-R1300 includes a switching power supply that automatically adapts to changes in mains voltage. The versatile ATW-T1001 UniPak body-pack transmitter has both a high-
impedance input for instruments, and a low-impedance input with bias connection for use with dynamic and electret condenser microphones. The ATW-T1002 handheld transmitter features a unidirectional dynamic microphone element. Both the body-pack and handheld transmitters use internal AA batteries and have Power/Mute switches and input Trim (level) adjustments. System 10 PRO Installation and Operation 3 Installation Receiver Unit Location For best operation, position receiver unit so it is off the floor, in line of sight of transmitter and away from any large obstructions. Keep the receiver unit away from noise sources such as other digital wireless equipment, microwave ovens, as well as away from large metal objects. Keep System 10 receivers 30' (9 m) away from wireless access points. Output Connection The ATW-R1300 is equipped with two audio outputs for each receiver:
a balanced XLR-type output and an unbalanced " TRS phone jack. Use shielded audio cable for the connection between the receiver and the mixer. If the input of the mixer is a " jack, connect a cable from the
" unbalanced audio output on the back of the receiver chassis to the mixer. If the input of the mixer is an XLR-type input, connect a cable from the balanced XLR-type audio output on the back of the chassis to the mixer. Power Connection Connect the DC plug on the included AC power adapter to the DC power input on the back of the receiver chassis. Secure the cord over the cord hook on the chassis to keep the plug from being accidentally dislodged. Plug the adapter into a standard 120 Volt 60 Hz AC power outlet. The receiver chassis is equipped with a power On/Off switch. Turn the power off when system is not in use, and unplug the power supply if you expect not to use the system for an extended period. Antennas For best reception, position the removable antennas in the shape of a V so that both tilt 45. Link Connection When using multiple systems together it is strongly recommended that you link all of the chassis (up to five) using the RJ12 cable included with each system. (Linking is not necessary if you are using only a single chassis.) Linking creates a much more stable environment in which receivers work together, with all receiving, transmitting and frequency allocation coordinated to prevent audio dropouts and enable simultaneous use of up to 10 channels. See Linking Systems on page 9 for more details. service technician. ATW-RC13 Receiver Chassis Controls and Functions Figure A Front Panel Controls and Functions 1. Power Switch: Press to turn power on and off. 2. Service Port: For use only by manufacturer or other qualified 3. Receiver Unit Docks: Insert individual receivers to use them locally. 4. Receiver Unit Releases: Press to eject receivers. 5. Audio Indicator (one for each receiver): Illuminates green when 6. Pairing Indicator (one for each receiver): Flashes green in pair mode;
7. System ID Select Switch (one for each receiver): Press to cycle through System ID numbers. (System ID is a shared number assigned to a paired receiver and transmitter for identification purposes.) sound is received from transmitter, yellow when audio is nearing peak level, and red when peak level is reached. illuminates solidly green once transmitter is paired. 8. Pairing Switch (one for each receiver): Press to initiate pairing. 9. System ID Display includes the following:
a. RF Signal Level Indicator (one for each receiver): Shows strength of the RF signal received from the transmitter b. System ID (one for each receiver): Shows the System c. Transmitter Battery Gauge TX (one for each receiver): Shows d. Link Indicator: Shows that the chassis has been linked to another chassis the capacity of the transmitters batteries ID number Figure A ON OFF 1 2 3 5 9 SYSTEM 10 PRO DIGITAL 2.4 GHz AUDIO PAIR AUDIO PAIR ID A PAIR ID B PAIR 4 6 7 8 b a d c System 10 PRO Installation and Operation 4 output jacks; maximum output is fully clockwise. receiver remotely up to 328' (100 m) from chassis. output jack (5) from ground. Normally, the switch should be to the left (ground connected). If hum caused by a ground loop occurs, slide switch to the right (ground lifted). Figure B, C & D Rear Panel Controls and Functions 1. RJ45 Connector: Use Ethernet cable (not included) to mount 2. AF Level (Volume) Control: Adjusts audio output level of both AF 3. Ground Lift Switch: Disconnects the ground pin of the balanced 4. Unbalanced Audio Output Jack: " phone jack. Can be connected 5. Balanced Audio Output Jack: XLRM-type connector. A standard 2-conductor shielded cable can be used to connect the receiver output to a balanced microphone-level input on a mixer or integrated amplifier. to an unbalanced aux-level input of a mixer, guitar amp or recording device. from pulling loose accidentally. 6. Receiver Chassis Link IN/OUT Connector: Use included RJ12 cable to link chassis to another ATW-R1300 chassis. Up to five chassis (10 receivers) may be linked. 7. Cord Hook: Loop the cord around the cord hook to keep the DC plug 8. Power Input Jack: Connect the DC plug from the included AC adapter. 9. Rack Mounting Brackets: Attach brackets to the sides of the receiver 10. Joining Plate: Attach to the bottom of two receiver chassis using chassis using supplied screws. supplied screws. Figure B 1 2 4 5 6 7 8 B VOLUME MIN. MAX. A VOLUME MIN. MAX. LINK TO EXTERNAL ATW-RU13 GROUND UNBALANCED BALANCED GROUND LIFT TO EXTERNAL ATW-RU13 GROUND UNBALANCED BALANCED GROUND LIFT OUT IN DC 12V IN 500 mA 3 Figure C Rack Mounting Brackets 9 Figure D Joining Plate 10 System 10 PRO Installation and OperationDIGITAL 2.4 GHz SYSTEM 10 PROIDPAIRAUDIOPAIRAUDIOONOFFPAIRIDPAIRAB 5 4. RJ45 Connector: Run Ethernet cable to chassis to mount receiver 5. Holder Release Tab: Lift tab up to release receiver from holder. remotely (cable not included). ATW-RU13 Receiver Unit Controls and Functions Figure E ATW-RU13 Functions 1. Antenna: Attach antennas and angle them away from each other so a V shape is formed. Antennas attach via SMA connectors. 2. Mounting Socket: "-20 thread socket for mounting receiver 3. Receiver Status Indicator: LED is off when receiver is without power, blinks slowly when receiver is not paired with a transmitter, blinks quickly during pairing process, and illuminates solidly green once receiver is paired with a transmitter. remotely to tripod or other device with a " screw. Figure E Figure F AT8690 RU13 Holder Front and Back 1 3 2 4 Figure G RU13 and RC13 5 System 10 PRO Installation and Operation 6 ATW-T1002 Transmitter Setup Controls and Functions Battery Selection and Installation Two alkaline AA batteries are recommended. When inserting the batteries, observe correct polarity as marked inside the battery compartment. Power / Battery / Mute Status Indicator Level Control System ID Display Pairing Switch Battery Compartment Screwdriver Figure G ATW-T1002 Handheld Transmitter Handheld Transmitter Battery Installation 1. While holding the upper part of the transmitter body just below the ball-screen, unscrew the lower body cover and slide it off to expose the battery compartment (Fig. G). 2. Carefully insert two fresh AA alkaline batteries, observing polarity markings. 3. Screw the body back together. Do not overtighten. Handheld Transmitter Battery Condition Indicator After the batteries are installed, press and hold the Power/Mute switch on the bottom of the handheld transmitter until the indicator LED turns green. If the indicator LED does not light up when the Power/Mute switch is pressed, the batteries are installed incorrectly or they are dead. The indicator LED will flash to show low-battery condition. Handheld Transmitter Mute Function With the transmitter on, a slight touch of the power switch will toggle between muted and unmuted operation. Red indicator LED shows muted operation. Green indicator LED shows unmuted operation. Handheld Transmitter Mute Lock Function Transmitter must be off to activate mute lock. Press and hold the Pairing Switch and then press and hold the Power/Mute button until transmitter powers on. Note: There is no dot next to the System ID when mute lock is activated. Transmitter must be off to deactivate mute lock. Press and hold the Pairing Switch and then press and hold the Power/Mute button until transmitter powers on. When deactivated, a dot will display next to the System ID. Power/Mute Switch Handheld Transmitter Pairing Switch Used to complete pairing sequence. See page 8. Handheld Transmitter Level Control Used to set microphone level. See page 8. Handheld Transmitter Screwdriver Used to adjust Level Control. See page 8. Handheld Transmitter System ID Display Shows System ID. See page 8. Note: System ID is a shared number assigned to a paired receiver and transmitter for identification purposes. When Power is applied, the System ID Display on the transmitter glows bright and then turns off to conserve battery life. To turn the System ID Display back on, mute and unmute the transmitter. System 10 PRO Installation and Operation 7 Microphone / Instrument Level Control Pairing Switch Screwdriver System ID Display Figure H ATW-T1001 UniPak Transmitter UniPak Transmitter Battery Installation 1. Slide off the battery cover.
, A A 6 R L Battery Compartment 2. Carefully insert two fresh AA alkaline batteries, observing polarity markings. 3. Replace the battery cover (Fig. H). Figure I UniPak Transmitter UniPak Transmitter Power/Mute/Battery Indicator After the battery is installed, press and hold the Power/Mute button until the indicator LED turns green (Fig. I). If the indicator LED does not light up when the power button is pressed, the batteries are installed incorrectly or they are dead. The indicator LED will flash to show low-
battery condition. UniPak Transmitter Mute Function With the transmitter on, a slight touch of the Power/Mute button will toggle between muted and unmuted operation. Red indicator LED shows muted operation. Green indicator LED shows unmuted operation. UniPak Transmitter Mute Lock Function Transmitter must be off to activate mute lock. Press and hold the Pairing Switch and then press and hold the Power/Mute button until transmitter powers on. Note: There is no dot next to the System ID when mute lock is activated. Transmitter must be off to deactivate mute lock. Press and hold the Pairing Switch and then press and hold the Power/Mute button until transmitter powers on. When deactivated, a dot will display next to the System ID. UniPak Transmitter Input Connection Connect an audio input device (microphone or guitar cable) to the audio input connector on the top of the transmitter. A number of Audio-Technica professional microphones and cables are available separately, pre-terminated with a UniPak input connector (see www.audio-technica.com). Power/Mute Button Input Connector Antenna Indicator LED
(Power/Mute/Battery) UniPak Transmitter Screwdriver Used to adjust Level Control. See page 8. UniPak Transmitter Antenna The UniPak transmitter includes a permanently-attached antenna. If the received signal is marginal, experiment with different transmitter positions on your body or instrument; or try repositioning the receiver. Do not attempt to remove, replace or change the length of the transmitting antenna. UniPak Transmitter System ID Display Shows System ID. See page 8. Note: System ID is a shared number assigned to a paired receiver and transmitter for identification purposes. When power is applied, the System ID Display on the transmitter glows bright and then turns off to conserve battery life. To turn the System ID Display back on, mute and unmute the transmitter. UniPak Transmitter Pairing Switch Used to complete pairing sequence. See page 8. UniPak Transmitter Microphone/Instrument Level Control Used to set microphone/instrument level. See page 8. System 10 PRO Installation and Operation 8 System Operation Turn down the volume control for both receivers and the mixer/amplifier level before starting up the wireless system. Do not switch on the transmitter yet. Receiver on... Plug the power supply into an AC power source, then turn on the power switch. The blue System ID Display will illuminate. Transmitter on... When the transmitter is switched on, Receiver A's green Pairing Indicator lights along with two indicators on the transmitter: the green Power/Battery/Mute status indicator and the blue System ID. The blue System ID display on the transmitter turns off after 30 seconds to conserve battery power; the transmitter Power/Battery/Mute status indicator will remain illuminated, indicating transmitter status. To re-illuminate System ID display, press the Power/Mute switch. Note:
this will alter the transmitter mute status. A slight touch of the power switch toggles between muted and unmuted operation. The transmitters Power/Battery/Mute status indicator glows red when transmitter is muted, or green to indicate unmuted status. In a low-
battery situation, the Power/Battery/Mute status indicator blinks. The transmitters have a soft-touch power switch. When the switch is set to Mute (red indicator LED), the transmitter produces RF with no audio signal. When the switch is On (green indicator LED) the transmitter produces both RF and audio. Excessive audio input to the transmitter will cause the receivers Audio Indicator to light red. Receiver Volume Under typical operating conditions, the receivers volume control should be turned all the way up, with overall system audio gain adjusted at the mixer or amplifier. Input Level Adjustment Input trimmer controls in the transmitters enable you to maximize performance for a particular microphone or guitar sensitivity, or to adjust for different acoustic input levels. Adjusting Input Level UniPak Transmitter Slide the battery cover off the transmitter and remove the screwdriver from its clip. Using the screwdriver, gently turn the VOL (Volume Microphone/Instrument Level) all the way up (clockwise, toward H). Check for excessive gain by speaking/singing into the microphone at typically loud levels while watching the receivers Audio Indicator. If the Audio Indicator lights red, turn the VOL control slightly counterclockwise until the Audio Indicator lights green or yellow with maximum audio input to the transmitter. Adjusting Input Level Handheld Transmitter Unscrew the lower body cover and slide it off, exposing the screwdriver and "LEVEL" (Gain Trimmer) control. Remove the screwdriver from its clip. Gently turn the "LEVEL" all the way up (clockwise, toward "H"). Check for excessive gain by speaking/singing into the microphone at typically loud levels while watching the receivers Audio Indicator. If the Audio Indicator lights red, turn the "LEVEL" control slightly counterclockwise until the Audio Indicator lights green or yellow with maximum audio input to the mic/transmitter. Return the screwdriver to its clip and close and secure the lower body. No further transmitter gain adjustments should be needed, as long as the acoustic input does not change significantly. CAUTION! The small trimmer controls are delicate; use only the supplied screwdriver. Do not force the trimmers beyond their normal 190 range of rotation. Setting System ID Number & Pairing your Transmitter and Receiver Your system has been preconfigured at the factory to operate with no other pairing setup required; it will work out of the box. That is, your receivers and transmitters are already digital pairs, with each transmitter sharing a System ID number with one of the receivers. The pairing instructions outlined below will help you if you find it necessary to change system ID numbers in multiple-system configurations, or pair a new transmitter to an existing receiver. NOTE: System ID is an identical number assigned to a paired receiver and transmitter for identification purposes. The System ID number is not related to transmitting frequency. Due to the dynamic nature of System 10's automatic frequency selection, the actual transmitting frequencies may change during power-up or performance. These frequency changes are seamless and imperceptible to the ear. number from 0 to 9 that you want. the System ID number will revert to its previous setting. beyond 100') of the chassis or in another room, you will need to insert another receiver unit into the pairing receivers empty dock. Follow the directions below, then eject the substitute receiver once pairing is complete. Pairing Receivers with Transmitters Note: Up to ten transmitters may be paired with any one receiver, and up to ten channels may be used simultaneously when multiple chassis are linked. (See Linking Systems on page 9.) 1. Turn on the receiver chassis and transmitter. 2. Press the System ID button on the chassis that corresponds to the receiver you wish to pair. The ID number will blink on the display. Continue to press the System ID button until the display shows the Note: When pairing a receiver that is mounted out of range (typically 3. Within 15 seconds, press and hold the Pair button on the receiver chassis for about one second. The receivers Pairing Indicator will begin to blink green. Your receiver is now in Pair Mode. Note: If the receivers Pair button is not pressed within 15 seconds, 4. Open your transmitter and press and hold its Pair button within 30 5. To pair an additional transmitter, you must switch off the first 6. Repeat for each additional transmitter you wish to pair with this receiver. Remember to switch off all transmitters already paired before adding a new one and to use a unique ID number for each transmitter. Note: With all transmitters turned off, the receivers System ID Display will cycle through all currently paired ID numbers. Turn will not recognize another paired transmitter until the receiver is on a transmitter to activate its pairing with the receiver. The receiver recognizes only one transmitter at a time. That transmitter must be turned off before the receiver will recognize another paired transmitter. If that transmitter is turned off out of range, the receiver seconds of entering Pair Mode. The transmitter display will now show the System ID number you have chosen on the receiver. The receivers Pairing Indicator will glow steady, indicating you have successfully paired your system. transmitter by pressing and holding its Power/Mute button. Turn the second transmitter on and follow instructions 2-4 above, making sure to assign a different System ID number to the new transmitter. powered off and turned on again. System 10 PRO Installation and Operation 9 4. While System 10 PRO has been designed to mount in a rack for convenient multi-system operation, please keep other wireless devices (including wireless systems and routers) away from System 10 PRO receivers. For best performance, some routers and Wi-Fi-
based wireless systems may need to be up to 30 feet away from System 10 PRO receivers. 5. Use the included RJ12 cable to link multiple (up to five) chassis. Linking the chassis will give you a stable multi-channel system with the use of up to 10 simultaneous channels. 6. The receiver antennas should be kept away from any metal. 7. As some guitar pickups may be overly sensitive to magnetic interfer-
ence, please keep the System 10 UniPak body-pack transmitter at least 1' (0.30 m) away from guitar pickups. 8. Use the transmitter level control to optimize performance for your sound source. 9. If the receiver output is set too low, the overall signal-to-noise ratio of the system may be reduced. Conversely, if the volume control on the receiver is set too high, it may over-drive the input of the mixer/
amplifier, causing distortion. Adjust the output level of the receiver so the highest sound pressure level going into the microphone (or the loudest instrument playing level) causes no input overload in the mixer, and yet permits the mixer level controls to operate in their normal range (not set too high or too low). This provides the opti-
mum signal-to-noise for the entire system. 10. Turn off chassis and transmitters when they are not in use. During extended periods of disuse, unplug chassis and remove batteries from transmitters. System Operating Frequencies Automatic Frequency Selection System 10 wireless systems operate in automatically selected frequen-
cies in the 2.4 GHz range, far from TV and DTV interference. Up to ten channels may be used together without any frequency coordination problems or group selection issues. Every time a receiver/transmitter pair is powered on, it automatically selects clear frequencies. Due to the dynamic nature of System 10 automatic frequency selection, these transmitting frequencies may change during power-up or performance if interference is encountered. These frequency changes occur at both the receiver and transmitter; they are seamless and imperceptible to the ear. Clearing Individual ID Pairings 1. Press the receivers System ID button to select the ID number you wish to clear. The number will begin to blink. 2. Press and hold the Pair button and, while continuing to hold it, press and hold the ID button until the display shows a blinking o. This indicates that your selected ID number has been cleared. 3. Release the Pair and ID buttons and, after a few seconds, the display will stop blinking and return to normal operation. 4. Repeat to clear additional ID pairings. Clearing All ID Pairings 1. Press and hold the receivers Pair button and, while continuing to hold it, press and hold the ID button until the display shows a blinking o. 2. Release the Pair and ID buttons. Then, within three seconds, press and hold the Pair and ID buttons again, until the display shows a blinking A. This indicates that all your paired ID numbers have been cleared. 3. After blinking three seconds, the A will change to - to indicate that there are no paired transmitters. Linking Systems Up to five chassis (10 receiver units) may be linked to allow the simultaneous use of up to 10 channels. If more than five chassis (10 receivers) are linked, error code E44 will flash on chassis' system ID display. Use the RJ12 cable that comes with each system to link multiple chassis. Run the RJ12 cable from the OUT connector of the first chassis to the IN connector of the second chassis. (If the IN/OUT connectors on the same chassis are linked, error code E41 will flash on chassis' system ID display.) When successfully linked, the word LINK will appear at the bottom of each chassis system ID display. To extend the link, run another RJ12 cable from the OUT connector of the second chassis to the IN connector of a third. Continue in this manner to link a fourth and fifth chassis. (The IN connector of the first chassis and the OUT connector of the last chassis in the chain will remain unused.) Ten Tips to Obtain the Best Results 1. Use only fresh alkaline or fully charged rechargeable batteries for the transmitter. 2. Position the receiver unit so that it has the fewest possible obstruc-
tions between it and the normal location of the transmitter. Line-of-
sight is best. 3. The transmitter and the receiver should be as close together as con-
veniently possible, but not less than 6' (2 m). System Frequencies For future reference, please record your system information here (the serial number appear on each transmitter, and on the bottom of each receiver chassis):
Receiver Model ATW-R1300 Transmitter Model ATW-T100 1 or 2 Serial Number Serial Number System 10 PRO Installation and Operation Specifications OvERALL SySTEM Operating Frequencies Dynamic Range Total Harmonic Distortion Operating Range Operating Temperature Range Frequency Response Audio Sampling Latency 2.4 GHz ISM band
>109 dB (A-weighted), typical
<0.05% typical 60 m (200') Open range environment with no interfering signals 0 C to +40 C (32 F to 104 F) Battery performance may be reduced at very low temperatures 20 Hz to 20 kHz Depending on microphone type 24 bit / 48 kHz 3.9 mS 4 UNIPAk TRANSMITTER RF Output Power Spurious Emissions Input Connection Batteries (not included) Battery Life Dimensions Net Weight (without batteries) 1 3 2 10 mW Following federal and national regulations Four-pin Locking Connector Pin 1: GND, Pin 2: INST INPUT, Pin 3: MIC INPUT, Pin 4: DC BIAS +9V Two 1.5V AA
>7 hours (alkaline) Depending on battery type and use pattern 70.2 mm (2.76") W x 107.0 mm (4.21") H x 24.9 mm (0.98") D 100 grams (3.5 oz) ATW-RU13 RECEIvER UNIT Receiving System Dimensions Net Weight Remote receiver connector Mounting Thread Insert Accessories Included Diversity (frequency/time/space) 57 mm (2.24") W x 19 mm (0.75") H x 77.6 mm (3.06") D 64 grams (2.3 oz) RJ45 1/4" x 20 Antennas, AT8690 RU13 holder ATW-RC13 RECEIvER CHASSIS Maximum Output Level Power Supply Dimensions Net Weight Remote receiver connector Link Connector Accessories Included XLR, balanced: 0 dBV 1/4" (6.3 mm), unbalanced: +6 dBV 100-240V AC (50/60 Hz) to 12V DC 0.5A power supply switched mode external 209.8 mm (8.26") W x 44 mm (1.73") H x 169.3 mm (6.67") D 940 grams (33.2 oz) RJ45 RJ12 AC adapter, Link cable, Rack-mount adapters, Joining plate, Rubber feet HANDHELD TRANSMITTER RF Output Power Spurious Emissions Batteries (not included) Battery Life Dimensions Net Weight (without batteries) Accessory Included 10 mW Following federal and national regulations Two 1.5V AA
>7 hours (alkaline) Depending on battery type and use pattern 254.8 mm (10.03") long, 50.0 mm (1.97") diameter 280 grams (9.9 oz) AT8456a Quiet-Flex stand clamp In the interest of standards development, A.T.U.S. offers full details on its test methods to other industry professionals on request. To reduce the environmental impact of a multi-language printed document, product information is available online at www.audio-technica.com in a selection of languages. Afin de rduire limpact sur lenvironnement de limpression de plusieurs langues, les informations concernant les produits sont disponibles sur le site www.audio-technica.com dans une large slection de langue. Para reducir el impacto al medioambiente, y reducir la produccin de documentos en varios leguajes, informacin de nuestros productos estn disponibles en nuestra pgina del Internet:
www.audio-technica.com. Para reduzir o impacto ecolgico de um documento impresso de vrias linguas, a Audio-Technica providncia as informaes dos seus produtos em diversas linguas na www.audio-technica.com. Per evitare limpatto ambientale che la stampa di questo documento determinerebbe, le informazioni sui prodotti sono disponibili online in diverse lingue sul sito www.audio-technica.com. Der Umwelt zuliebe finden Sie die Produktinformationen in deutscher Sprache und weiteren Sprachen auf unserer Homepage: www.audio-technica.com. Om de gevolgen van een gedrukte meertalige handleiding op het milieu te verkleinen, is productinformatie in verschillende talen on-line beschikbaar op: www.audio-technica.com. www.audio-technica.com www.audio-technica.com System 10 PRO Installation and Operation 11 System 10 PRO Installation and Operation 12 Audio-Technica Corporation audio-technica.com 2014 Audio-Technica P52551 System 10 PRO Installation and Operation
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2014-12-05 | 2403 ~ 2481 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2014-12-05
|
||||
1 | Applicant's complete, legal business name |
Audio-Technica Corporation
|
||||
1 | FCC Registration Number (FRN) |
0028730448
|
||||
1 | Physical Address |
2-46-1 Nishi-naruse, Machida
|
||||
1 |
Tokyo, N/A 194-8666
|
|||||
1 |
Japan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
e******@ul.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
JFZ
|
||||
1 | Equipment Product Code |
RU13
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
F******** K********
|
||||
1 | Title |
General Manager, Engineering Planning Division
|
||||
1 | Telephone Number |
81-42********
|
||||
1 | Fax Number |
81-42********
|
||||
1 |
k******@audio-technica.co.jp
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
UL Japan, Inc.
|
||||
1 | Name |
T******** S******
|
||||
1 | Physical Address |
4383-326 Asama-cho, Ise-shi
|
||||
1 |
Mie-ken, 516-0021
|
|||||
1 |
Japan
|
|||||
1 | Telephone Number |
81-59********
|
||||
1 | Fax Number |
81-59********
|
||||
1 |
T******@ul.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless Receiver Unit | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power listed is Conducted(Peak). The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except the conditions shown in this filing and/or in accordance with FCC multi-transmitter product guidelines. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
UL Japan, Inc. Head office EMC Lab.
|
||||
1 | Name |
T**** H********
|
||||
1 | Telephone Number |
+81-5********
|
||||
1 | Fax Number |
+81-5********
|
||||
1 |
T******@jp.ul.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2403.00000000 | 2481.00000000 | 0.0062000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC