FCC ID: 2AG32EG2030CM2 LTE Indoor CPE

Baicells EG2030C-M2 User Manual V100R001C00 02 All rights reserved Baicells Technologies Co., Ltd. About This Document This document introduces the specifications of Baicells EG2030C-M2 CPE and guides users to install and configure it. Copyright Notice Baicells copyrights this specification. No part of this specification may be reproduced in any form or means, without the prior written consent of Baicells. Disclaimer This specification is preliminary and is subject to change at any time without notice. Baicells assumes no responsibility for any errors contained herein. For more information, please consult our technical engineers. Disposal of Electronic and Electrical Waste Pursuant to the WEEE EU Directive, electronic and electrical waste must not be disposed of with unsorted waste. Please contact your local recycling authority for disposal of this product. Revision Record Date Version Description 5 June,2017 V1.0 Initial released. Contact Us Baicells Technologies Co., Ltd.North America Address: 555 Republic Drive, Suite 200 Plano, TX 75074 E-mail: support_na@baicells.com Phone: +1-972-800-1157 Website: http://www.baicells.com/

Contents 1. Product Overview ......................................................................................................... 1 1.1 Introduction .............................................................................................................. 1 1.2 Features ..................................................................................................................... 1 1.3 Appearance ............................................................................................................... 1 2. Technical Specifications ............................................................................................... 4 2.1 Basic Specification .................................................................................................... 4 2.2 RF Specification ........................................................................................................ 4 2.3 SW Specification ....................................................................................................... 5 2.4 Device Management .................................................................................................. 5 2.5 Environment Specification ......................................................................................... 6 2.6 Regulatory Compliance .............................................................................................. 6 3. Configuration Guide ..................................................................................................... 8 3.1 Log in .......................................................................................................................... 8 3.2 View Status ................................................................................................................. 8 3.3 Basic Configuration .................................................................................................... 9 3.3.1 LTE Setting .......................................................................................................... 9 3.3.2 Set Connection Method ...................................................................................... 9 3.3.3 Set Scan Mode .................................................................................................. 10 3.3.4 Lock Frequency (Earfcn) ................................................................................... 10 3.3.5 Lock PCI ............................................................................................................. 11 Appendix A Appendix B FAQs ......................................................................................................... 13 Shipping List ............................................................................................. 14 Figures Figure 1-1 EG2030C-M2 Appearance .......................................................................... 2 Figure 1-3 LED Indicators of EG2030C-M2 ................................................................. 2 Figure 4-1 Login Page .................................................................................................. 8 Figure 4-2 View Status ................................................................................................. 9 Figure 4-3 Set Connection Method .............................................................................. 9 Figure 4-4 Set Scan Mode ......................................................................................... 10 Figure 4-5 Lock Frequency ........................................................................................ 11 Figure 4-6 Lock Frequency ........................................................................................ 12 Tables Table 1-1 Description of EG2030C-M2 Interface and Button ....................................... 2 Table 1-2 LED Indicator Description ............................................................................. 3 Table 2-1 Basic Specification ....................................................................................... 4 Table 2-2 RF Specification ........................................................................................... 4 Table 2-3 SW Specification .......................................................................................... 5 Table 2-4 Device Management ..................................................................................... 5 Table 2-5 Environment Specification ............................................................................ 6 1. Product Overview 1.1 Introduction Baicells is a high-tech company dedicated in wireless broadband access solutions and service operation. With the advent of the Internet+ era, the development of WBB is imminent. Through continuous innovation, Baicells launches the world first mobile broadband system based on the Internet architecture and unlicensed spectrum. Baicells can provide series CPEs, include indoor and outdoor unit on different spectrums. Baicells EG2030C-M2 is high performance outdoor CPE. The EG2030C-M2 has the superior wireless access performance and comprehensive routing capabilities, which have the abilities to bring the end-users WBB services. 1.2 Features The EG2030C-M2 is designed according to the simplicity principle, which can evolve in a short period and realize fast customization, delivery and deployment as well. The main features of the EG2030C-M2 is as follows:

Support TD-LTE network according to the operators choice. LTE comply with 3GPP Release9 CAT4. LTE TDD band42&band43. Support the 100Mbps Ethernet interface. Support 802.11bgn. Intuitionist and convenient Web-based management. Support TR069 and OMA-DM network management protocol. Support cell lock, SIM lock, and Pin lock. User-friendly design of LED indicator. 1.3 Appearance The EG2030C-M2 appearance is shown in Figure 1-1. 1 Figure 1-1 EG2030C-M2 Appearance The EG2030C-M2 interface and button description is given in Table 1-1. Table 1-1 Description of EG2030C-M2 Interface and Button Interface & Button Description Power Switch Power On/Off SIM RESET LAN Support 1.8V/3.0V USIM 2FF Long press over 10 seconds to restore the factory settings 1 RJ45, LAN, 10/100/1000 auto-sensing, auto-MDX The LED indicators are shown in Figure 1-2. Figure 1-2 LED Indicators of EG2030C-M2 The description of LED indicators are given in Table 1-2. 2 Table 1-2 LED Indicator Description Identity Description Color Status Description Power Network state OFF No Power Supply. Indicator Blue Steady On Power on. WLAN SIM card status Yellow Steady On WLAN is on. indicator Blanking WLAN is off. LTE Power Indicator Yellow OFF LTE disconnected. Steady On LTE connected. LTE Signal 3 LTEs, Indicate Green All OFF Signal is too weak to attach. connection state and signal strength Steady On According to signal strength in turn light up Blanking Scanning the LTE network The CPE is authenticating. CPE is getting IP address from the LTE network. 3 2. Technical Specifications 2.1 Basic Specification Item Description LTE Standard 3GPP Release 9 Table 2-1 Basic Specification Ethernet LAN Port One RJ-45 port 10/100 auto-sensing, auto-MDX LED Indicators Power/LET Signal/WLAN USIM Support 1.8V/3V 2FF Restore Button Tact Button Power Supply Input: Universal range 100V~240V AC Long press over 10s to restore the factory settings Dimension Weight Color Output: 5VDC, 2A About About 400g Pantone white C 2.2 RF Specification Item LTE Mode Table 2-2 RF Specification Description TDD LTE Channel Bandwidth MAX Output Power 5 MHz /10 MHz /15 MHz /20 MHz 232 dBm LTE Standard Frequency 3GPP R9 Band42: 3400 MHz ~ 3600 MHz Band43: 3600 MHz ~ 3800 MHz LTE Antenna Gain 6 dBi Wifi Standard Frequency 802.11b/g/n 2400MHz~2483.5 MHz Wifi Antenna Gain 5 dBi 4 2.3 SW Specification Table 2-3 SW Specification Item Description Language Settings English Network Mode Bridge / NAT SIM PIN Management SIM Lock Network Connection setup Create, delete, and edit APNs Set up dial-up connection automatically Set up dial-up connection manual LTE Scan Mode Full Band Cell Lock VPN NAT Statistics Band / Frequency Preferred Support VPN pass through Support L2TP tunnel mode Support L2 VPN Port forwarding Port trigger DMZ UPnP LAN Link Status Transmit / Receive traffic Running Time 2.4 Device Management Item Maintenance TR069 Port mirror Syslog Table 2-4 Device Management Description Date & Time setting Reset Restore factory settings Restore/Backup Configuration File Local upgrade FOTA upgrade Can enable or disable TR069 Management Can enable or disable the port mirror function Support the syslog function can send the log to the PC via LAN Diagnostics Support the Ping and trace route 5 2.5 Environment Specification Table 2-5 Environment Specification Item Description Operating Temperature Storage Temperature

-10 ~ 40

-20 ~ 70 Operating Humidity 5% ~ 95%

2.6 Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 30cm between the radiator & your body. ISEDC Compliance This device complies with Innovation, Science, and Economic Development 6 Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause in terference, and (2) This device must accept any interference, including interference t hat may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d' Innovation, Science et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 30cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter, End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance. 7 3. Configuration Guide 3.1 Log in The EG2030C-M2 manages, configures, and maintains the device by web management page. The steps to log in are as follows:

1. In the address column of browser, type in http://192.168.150.1, then press Enter, login in page is shown in Figure 3-1. Figure 3-1 Login Page 2. Enter the user name and password, click "LOGIN". After password authentication, you can log on to the web management page. The default user name and password is admin. For security, it is recommended that you open the firewall, and keep your login password, WLAN FTP passwords and password well. 3.2 View Status In the overview area, you can view the device information and LTE status, such as Product name, Software version, PLMN, IMSI, RSRP, RSRQ, CINR, SINR, Tx Power, Cell ID, PCI, and so on, as shown in Figure 3-2. 8 Figure 3-2 View Status 3.3 Basic Configuration 3.3.1 LTE Setting To set the LTE Network, perform the following steps:

1. Choose LTE. 2. In the LTE Setting area, configure the LTE network. 3.3.2 Set Connection Method To set the LTE network connection method, perform the following steps:

1. Choose LTE>connection Method, enter the setting connection method page, as shown in Figure 3-3. Figure 3-3 Set Connection Method 9 2. In the connection Method area, set the connection method 3. There are two methods to connect the LTE network, it is needed to choose a method between Auto and Manual, if you want to auto connect to the LET network you should choose the Auto, otherwise you should choose Manual. 4. Click SAVE & APPLY. 3.3.3 Set Scan Mode To set the LTE network scan mode, perform the following steps:

1. Choose LTE>Scan Method, enter the setting scan method page, as shown in Figure 3-4. Figure 3-4 Set Scan Mode 2. In the Scan Method area, set the scan mode 3. You can choose full Band, Frequency Lock, or PCI Lock. 3.3.4 Lock Frequency (Earfcn) To clock the frequency, perform the following steps:

1. Choose LTE>Scan Method. 2. In the LTE Scan Method area, click Frequency Lock to lock the frequency. 3. Click ADD LIST, choose a band and frequency, and then click Add to add the band and frequency to the list, as shown in Figure 3-5. 10 Figure 3-5 Lock Frequency 4. Click SAVE & APPLY. 3.3.5 Lock PCI To lock the PCI, perform the following steps:

1. Choose LTE>Scan Method. 2. In the LTE Scan Method area, click PCI Lock to lock the PCI. 3. Click ADD LIST you can choose a band, frequency and PCI, then click Add to add the frequency and PCI to the list, as shown in Figure 3-6. 11 Figure 3-6 Lock Frequency 4. Click SAVE & APPLY. 12 Appendix A FAQs The POWER indicator does not turn on. Make sure that the power cable is connected properly and the CPE is powered on. Make sure that the power adapter is compatible with the CPE. Fails to Login to the web management page. Make sure that the CPE is started. Verify that the CPE is correctly connected to the computer through a network cable. If the problem persists, contact authorized local service suppliers. The CPE fails to search for the wireless network. Check that the power adapter is connected properly. Check that the CPE is placed in an open area that is far away from obstructions, such as concrete or wooden walls. Check that the CPE is placed far away from household electrical appliances that generate strong electromagnetic field, such as microwave ovens, refrigerators, and satellite dishes. If the problem persists, contact authorized local service suppliers. The power adapter of the CPE is overheated. The CPE will be overheated after being used for a long time. Therefore, power off the CPE when you are not using it. Check that the CPE is properly ventilated and shielded from direct sunlight. The parameters are restored to default values. If the CPE powers off unexpectedly while being configured, the parameters may be restored to the default settings. After configuring the parameters, download the configuration file to quickly restore the CPE to the desired settings. 13 Appendix B Shipping List The product outward appearance, the color take the material object as, the picture only Amount 1 1 1 supply reference. Index Content Picture EG2030C-M2 CPE with Simple Mounting bracket Power adapter User Manual 1 2 3 14