FCC ID: 2AG32EG7010AM11 LTE Outdoor CPE

Baicells EG7010A-M11 User Manual V100R001C00 01 All rights reserved Baicells Technologies Co., Ltd. About This Document This document introduces the specifications of Baicells EG7010A-M11 CPE and guides users to install and configure it. Copyright Notice Baicells copyrights this specification. No part of this specification may be reproduced in any form or means, without the prior written consent of Baicells. Disclaimer This specification is preliminary and is subject to change at any time without notice. Baicells assumes no responsibility for any errors contained herein. For more information, please consult our technical engineers. Revision Record Date Version Description 24 Jan,2017 V1.0 Initial released. Contact Us Baicells Technologies Co., Ltd.North America Address: 555 Republic Drive, Suite 200 Plano, TX 75074 E-mail: support_na@baicells.com Phone: +1-972-800-1157 Website: http://www.baicells.com/

Contents 1. Product Overview ....................................................................................................... 1 1.1 Introduction .......................................................................................................... 1 1.2 Features ................................................................................................................ 1 1.3 Appearance ........................................................................................................... 2 2. Technical Specifications ............................................................................................... 5 2.1 Basic Specification ................................................................................................ 5 2.2 RF Specification ..................................................................................................... 5 2.3 SW Specification ................................................................................................... 5 2.4 Device Management ............................................................................................... 6 2.5 Environment Specification ...................................................................................... 6 3. Installation Guide.......................................................................................................... 8 3.1 Support Materials ................................................................................................... 8 3.2 Install USIM Card and Ethernet Cable ..................................................................... 8 3.3 Install on Pole ......................................................................................................... 9 3.4 Install on Wall ....................................................................................................... 10 3.5 Grounding ............................................................................................................ 10 3.6 Regulatory Compliance ......................................................................................... 11 4. Configuration Guide ................................................................................................... 13 4.1 Log in .................................................................................................................... 13 4.2 View Status ........................................................................................................... 13 4.3 Basic Configuration ............................................................................................... 14 4.3.1 LTE Setting .................................................................................................... 14 4.3.2 Set Connection Method................................................................................. 14 4.3.3 Set Scan Mode .............................................................................................. 15 4.3.4 Lock Frequency (Earfcn) ................................................................................ 15 4.3.5 Lock PCI ......................................................................................................... 16 Appendix A FAQs ......................................................................................................... 19 Appendix B Shipping List ............................................................................................. 20 Figures Figure 1-1 EG7010A-M11 Appearance ........................................................................ 2 Figure 1-2 Interface and Button of EG7010A-M11 ....................................................... 2 Figure 1-3 LED Indicators of EG7010A-M11 ................................................................ 3 Figure 3-1 Install Ethernet Cable and USIM Card ....................................................... 8 Figure 3-2 Connection Diagram ................................................................................... 9 Figure 3-3 Install the Bracket ....................................................................................... 9 Figure 3-4 Install on Pole............................................................................................ 10 Figure 3-5 Install on Wall ............................................................................................ 10 Figure 3-6 Grounding ................................................................................................. 11 Figure 4-1 Login Page ................................................................................................ 13 Figure 4-2 View Status ............................................................................................... 14 Figure 4-3 Set Connection Method ............................................................................ 14 Figure 4-4 Set Scan Mode ......................................................................................... 15 Figure 4-5 Lock Frequency ........................................................................................ 16 Figure 4-6 Lock Frequency ........................................................................................ 17 Tables Table 1-1 Description of EG7010A-M11 Interface and Button ..................................... 2 Table 1-2 LED Indicator Description ............................................................................. 3 Table 2-1 Basic Specification ....................................................................................... 5 Table 2-2 RF Specification ........................................................................................... 5 Table 2-3 SW Specification .......................................................................................... 5 Table 2-4 Device Management ..................................................................................... 6 Table 2-5 Environment Specification ............................................................................ 7 Table 3-1 Support Materials for Installing ..................................................................... 8 1. Product Overview 1.1 Introduction Baicells is a private, high-tech company providing innovative LTE wireless broadband access solutions. The Baicells solutions support fixed wireless access and mobile scenarios. With the vision to connect the unconnected, Baicells has introduced breakthrough technologies to LTE, like moving a complete LTE system to unlicensed spectrum and building it with an IT based architecture. With the Baicells turnkey end-to-end solutions, it becomes much easier to provide wireless internet within everyone's reach at a very low cost. These innovative solutions can be used by mobile operators, broadband access operators, Internet Service Providers (ISP), Mobile Virtual Network Operators

(MVNO), governments, and enterprise private networks. The Baicells EG7010A-M11 Outdoor Customer Premise Equipment (CPE) provides superior wireless access performance and comprehensive routing capabilities to bring wireless broadband data and voice services to end -users. 1.2 Features The EG7010A-M11 is designed according to the simplicity principle, which can evolve in a short period and realize fast customization, delivery and deployment as well. The main features of the EG7010A-M11 is as follows:

Supports LTE-TDD frequency bands 48. Complies with 3GPP Release 10 CAT6/7 standards. 1000 Mbps Ethernet interface. Convenient, simple, GUI-based local and remote Web management. Built-in LTE bipolar directional high-gain antenna. TR069 network management protocol. Cell lock, SIM lock, and Pin lock. User-friendly LED indicators. Power supply with PoE. Pole mounted or wall mounted. 1 1.3 Appearance The EG7010A-M11 appearance is shown in Figure 1-1. Figure 1-1 EG7010A-M11 Appearance The EG7010A-M11 interfaces and buttons are shown in Figure 1-2. Figure 1-2 Interface and Button of EG7010A-M11 The EG7010A-M11 interface and button description is given in Table 1-1. Table 1-1 Description of EG7010A-M11 Interface and Button Interface & Button Description 2 Interface & Button Description PoE USIM Slot Connected to the PoE power adapter Support 1.8V/3.0V USIM 2FF Restore Button Long press over 10 seconds to restore the factory settings LED Indicator LTE signal strength Indicator& status indicator GND Connected to Earth by conductor The LED indicators are shown in Figure 1-3. Figure 1-3 LED Indicators of EG7010A-M11 The description of LED indicators are given in Table 1-2. Table 1-2 LED Indicator Description Identity Description Color Status Description MIU Yellow OFF Reserved.

Steady On Reserved. Blanking Reserved. LTE Network state OFF LTE disconnected. Indicator Blue Steady On LTE connected. SIM SIM card status Yellow Steady On The SIM card is normal. indicator Blanking The SIM card is abnormal or not inserted. LAN 100Mbps Eth Yellow OFF Ethernet connection does not Indication established. Steady On Ethernet connection is normal. Blanking Data is transmitting. 3 Identity Description Color Status Description PWR Power Indicator Yellow OFF No Power Supply Steady On Power On LTE Signal 5 LTEs, Indicate Green All OFF Signal is too weak to attach. connection state and signal strength Steady On According to signal strength in turn light up Blanking Scanning the LTE network The CPE is authenticating. CPE is getting IP address from the LTE network. 4 2. Technical Specifications 2.1 Basic Specification Item Description LTE Standard 3GPP Release 10/11 Table 2-1 Basic Specification Ethernet LAN Port One RJ-45 port 10/100/1000 auto-sensing, auto-MDX, PoE LED Indicators Power/LET Signal/LAN Indicator USIM Support 1.8V/3V 2FF Restore Button Tact Button Power Supply Dimension Weight Color Long press over 10s to restore the factory settings Input: Universal range 100V~240V AC About 248mm * 248mm * 80mm About 1800g Pantone white C 2.2 RF Specification Item LTE Mode Channel Bandwidth MAX Output Power LTE Standard Frequency Antenna Gain Table 2-2 RF Specification Description TDD LTE 5 MHz /10 MHz /15 MHz /20 MHz 27 dBm 3GPP R10/11 Band48: 3550 MHz ~ 3700 MHz 14 dBi 2.3 SW Specification Item Table 2-3 SW Specification Description Language Settings English Network Mode Bridge / NAT SIM PIN Management 5 Item Description SIM Lock Network Connection setup Create, delete, and edit APNs Set up dial-up connection automatically Set up dial-up connection manual LTE Scan Mode Full Band Cell Lock VPN NAT Statistics Band / Frequency Preferred Support VPN pass through Support PPTP tunnel mode Port forwarding Port trigger DMZ UPnP LAN Link Status Transmit / Receive traffic Running Time 2.4 Device Management Item Maintenance TR069 Port mirror Syslog Table 2-4 Device Management Description Date & Time setting Reset Restore factory settings Restore/Backup Configuration File Local upgrade FOTA upgrade Can enable or disable TR069 Management Can enable or disable the port mirror function Support the syslog function can send the log to the PC via LAN Diagnostics Support the Ping and trace route 2.5 Environment Specification 6 Table 2-5 Environment Specification Item Description Operating Temperature Storage Temperature

-40 ~ 55

-40 ~ 70 Operating Humidity 5% ~ 95%

Drop 0.8m 7 3. Installation Guide 3.1 Support Materials Before installation, prepare the following support materials accordingly, as given in Table 3-1. Table 3-1 Support Materials for Installing Item Description Ethernet cable Outdoor Shield CAT5E Shorter than 330 feet Ground wire 16mm yellow-green wire 3.2 Install USIM Card and Ethernet Cable 1. Screw the two screws on the waterproof cover. 2. Open the waterproof cover, and connect the Ethernet cable to the Ethernet interface. 3. Insert the USIM card to the USIM slot. Note following the directions. 4. Close the waterproof cover and tighten the two screws on the cover, as shown in Figure 3-1. Figure 3-1 Install Ethernet Cable and USIM Card 8 5. Connected Ethernet cable to the power adapter, as shown Figure 3-2. Pay attention to the power adapter interface directions. Figure 3-2 Connection Diagram 6. Power on, the LED indicator will light up. 3.3 Install on Pole 1. Tighten the screws at the bottom of the bracketas shown in Figure 3-3. Figure 3-3 Install the Bracket 2. Install the bracket on pole as shown as Figure 3-4. 9 Figure 3-4 Install on Pole 3.4 Install on Wall Install bracket on wall as show as Figure 3-5. Figure 3-5 Install on Wall 3.5 Grounding The EG7010A-M11 must be grounding, please contact professional person to operation. 10 Using grounding cable, connect the grounding screw to the ground row, as shown in Figure 3-6. Figure 3-6 Grounding 3.6 Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

11 Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 30cm between the radiator & your body. 12 4. Configuration Guide 4.1 Log in The EG7010A-M11 manages, configures, and maintains the device by web management page. The steps to log in are as follows:

1. In the address column of browser, type in http://192.168.150.1, then press Enter, login in page is shown in Figure 4-1. Figure 4-1 Login Page 2. Enter the user name and password, click "LOGIN". After password authentication, you can log on to the web management page. The default user name and password is admin. For security, it is recommended that you open the firewall, and keep your login password, WLAN FTP passwords and password well. 4.2 View Status In the overview area, you can view the device information and LTE status, such as Product name, Software version, PLMN, IMSI, RSRP, RSRQ, CINR, SINR, Tx Power, Cell ID, PCI, and so on, as shown in Figure 4-2. 13 Figure 4-2 View Status 4.3 Basic Configuration 4.3.1 LTE Setting To set the LTE Network, perform the following steps:

1. Choose LTE. 2. In the LTE Setting area, configure the LTE network. 4.3.2 Set Connection Method To set the LTE network connection method, perform the following steps:

1. Choose LTE>connection Method, enter the setting connection method page, as shown in Figure 4-3. Figure 4-3 Set Connection Method 14 2. In the connection Method area, set the connection method 3. There are two methods to connect the LTE network, it is needed to choose a method between Auto and Manual, if you want to auto connect to the LET network you should choose the Auto, otherwise you should choose Manual. 4. Click SAVE & APPLY. 4.3.3 Set Scan Mode To set the LTE network scan mode, perform the following steps:

1. Choose LTE>Scan Method, enter the setting scan method page, as shown in Figure 4-4. Figure 4-4 Set Scan Mode 2. In the Scan Method area, set the scan mode 3. You can choose full Band, Frequency Lock, or PCI Lock. 4.3.4 Lock Frequency (Earfcn) To clock the frequency, perform the following steps:

1. Choose LTE>Scan Method. 2. In the LTE Scan Method area, click Frequency Lock to lock the frequency. 3. Click ADD LIST, choose a band and frequency, and then click Add to add the band and frequency to the list, as shown in Figure 4-5. 15 Figure 4-5 Lock Frequency 4. Click SAVE & APPLY. 4.3.5 Lock PCI To lock the PCI, perform the following steps:

1. Choose LTE>Scan Method. 2. In the LTE Scan Method area, click PCI Lock to lock the PCI. 3. Click ADD LIST you can choose a band, frequency and PCI, then click Add to add the frequency and PCI to the list, as shown in Figure 4-6. 16 Figure 4-6 Lock Frequency 4. Click SAVE & APPLY. 17 4.3.6 SAS Settings 18 Appendix A FAQs The POWER indicator does not turn on. Make sure that the power cable is connected properly and the CPE is powered on. Make sure that the power adapter is compatible with the CPE. Fails to Login to the web management page. Make sure that the CPE is started. Verify that the CPE is correctly connected to the computer through a network cable. If the problem persists, contact authorized local service suppliers. The CPE fails to search for the wireless network. Check that the power adapter is connected properly. Check that the CPE is placed in an open area that is far away from obstructions, such as concrete or wooden walls. Check that the CPE is placed far away from household electrical appliances that generate strong electromagnetic field, such as microwave ovens, refrigerators, and satellite dishes. If the problem persists, contact authorized local service suppliers. The power adapter of the CPE is overheated. The CPE will be overheated after being used for a long time. Therefore, power off the CPE when you are not using it. Check that the CPE is properly ventilated and shielded from direct sunlight. The parameters are restored to default values. If the CPE powers off unexpectedly while being configured, the parameters may be restored to the default settings. After configuring the parameters, download the configuration file to quickly restore the CPE to the desired settings. 19 Appendix B Shipping List The product outward appearance, the color take the material object as, the picture only Amount 1 1 1 1 1 supply reference. Index Content Picture EG7010A-M11 CPE Power cord PoE adapter Mounting bracket 1 2 3 4 User Manual 5 20

Baicells Technologies Co., Ltd. Date: Dec. 30, 2019 File Name Schematics.pdf Block Diagram.pdf Operational Description.pdf Part List.pdf Tune-up Procedure.pdf Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AG32EG7010AM11 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Schematics Block Diagram Operational Description Part List Tune-up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Baicells Technologies Co., Ltd. Signature Back Huang/ Manager Typed name and Title

Baicells Technologies Co., Ltd. Date: 12/30/2019 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD To Whom It May Concern:

We, Baicells Technologies Co., Ltd., state that our device, FCC ID: 2AG32EG7010AM11, has a non-removable rear cover. The label will be placed on the rear cover. And the label will be visible to the end users when they purchase the product. The back cover can not be moved away, so the FCC ID label has to be placed on the surface of product. Sincerely, Signature

[Back Huang (Name)]

[Manager(Title)]

[Baicells Technologies Co., Ltd. (Company name)]

Baicells Technologies Co., Ltd. FCC ID: 2AG32EG7010AM11 POWER OF ATTORNEY Date: Dec. 30, 2019 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd.

(Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on Dec. 29, 2020. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Baicells Technologies Co., Ltd. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Baicells Technologies Co., Ltd. Signature Back Huang / Manager Typed name and Title