submitted | available | document details (if available) | source link |
---|---|---|---|
January 07 2020 | January 13 2020 | ATOM OD06 - EG7010C USER Manual admin Microsoft® Word 2010 |
various | User Manual | Users Manual | 1.16 MiB | January 07 2020 / January 13 2020 |
ATOM OD06 - EG7010C-M11 USER Manual 01 All rights reserved Baicells Technologies Co., Ltd. 1. Shipping List Make sure you have got the following parts:
EG7010C Quick Guide PoE Adapter Power Cord Standard Mounting Kits Optional Mounting Kits 2 2. Hardware Introduction 2.1 Indicators Identity Description Color Status Description MIU Yellow OFF Reserved.
Steady On Reserved. Blanking Reserved. LTE Network state OFF LTE disconnected. Indicator Blue Steady On LTE connected. SIM SIM status indicator card Yellow Steady On The SIM card is normal. Blanking The SIM card is abnormal or not LAN 100Mbps Eth Indication Yellow OFF inserted. Ethernet established. connection does not Steady On Ethernet connection is normal. Blanking Data is transmitting. PWR Power Yellow OFF No Power Supply Indicator Steady On Power On LTE Signal LTEs, 5 Indicate Green All OFF Signal is too weak to attach. Steady On According to signal strength in turn light Identity Description Color Status Description connection and state signal strength up Blanking Scanning the LTE network The CPE is authenticating. CPE is getting IP address from the LTE network. 2.2 Interface and Buttons Interface & Button Description PoE TF SIM RESET GND Connected to the PoE Power Adapter Support SD card Support 1.8V/3.0V USIM 2FF Long press over 10 seconds to restore the factory settings Connected to Earth by conductor 3. Installation Guide 3.1 Support Materials Before installation, prepare the following support materials accordingly, as given below:
Item Description Ethernet cable Outdoor Shield CAT5E Shorter than 330 feet Ground wire 16mm yellow-green wire 3.2 Install USIM Card and Cables
(1) Screw the screw on the waterproof cover, and open the waterproof cover
(2) Insert the USIM card to the USIM slot. Note following the directions
(3) Connect the Ethernet cable to the PoE
(4) connect the ground cable to the port ground screw
(5) Close the waterproof cover and fasten the screw on the cover.
(6) Connected Ethernet cable to the power adapter. Pay attention to the power adapter interface directions.
(7) Power on, the LED indicator will light up. 4. Configuration Guide 4.1 4.1 Login The CPE manages, configures, and maintains the device by web management page. The steps to log in are as follows:
1. In the address column of browser, type in http://192.168.150.1, then press Enter:
2. Enter the user name and password, click "LOGIN". After password authentication, you can log on to the web management page. The default user name and password is admin. For security, it is recommended that you open the firewall, and keep your login password, WLAN FTP passwords and password well. 4.2 View Status In the overview area, you can view the device information and LTE status,such as Product name, Software version, PLMN, IMSI, RSRP, RSRQ, CINR, SINR, Tx Power, Cell ID, PCI, and so on, as shown below:
5. Specifications Basic Specifications Item Description UE-Category 3GPP R10, CAT 6/7 USIM Slot 1.8V/3.0V USIM 2FF Ethernet Port Power Supply Reset Button 1 RJ45, LAN, 10/100/1000 auto-sensing, auto-MDX, PoE Input: Universal range 100V~240V AC Output: PoE (24V DC, 0.5A) Tactile button. Long press over 10s to restore the factory settings LED Indicators MIU/LTE/SIM/LAN/PWR/LTE Signal Dimensions 241mm (H) x 154mm (W) x 50mm (D) Weight About 900 g LTE Specifications Item Description LTE Mode LTE-TDD LTE Bands Band 48 TXRX 2T4R Channel Bandwidth 5MHz, 10MHz, 15MHz, 20MHz Modulation QPSK, 16QAM Receive Sensitivity
-94dBm @ QPSK,20MHz, 25C MAX Output Power 26dBm Antenna Type Internal directional-antenna Antenna Gain 11dBi@3.xGHz, 2 Ports Polarization Antenna Efficiency Isolation VSWR 45
>70%
-25dB 2 Horizontal Beam Width (3dB) 603@3.xGHz, 2 Ports Vertical Beam Width (3dB) 255@3.xGHz, 2 Ports SW Specifications Item Description Language Support English/Chinese Network Mode NAT/Bridge/Tunnel IP Protocol IPv4/IPv6 SIM Management PIN Management, SIM Lock Network Connection Management Auto/Manual LTE Scan Mode Full band scan, Frequency Lock WLAN WPS MSSID Isolation VLAN VPN NAT Firewall L2TP GRE Port forwarding DMZ ALG Port Trigger Access Control Block Port Scanner / SYN Flood SPI Filter IP/MAC/URL Filter Network Management TR069 SNMP Diagnostics Statistics Maintenance System Log LTE Status/Connection Time/System Up Time TCPDump Ping Trace route Device Status DHCP Client List WiFi Station List Firewall Status LTE Status Date & Time setting Reboot Restore factory settings Restore / Back up configuration file Firmware upgrade locally/OTA (over the air) Operating Log Run-time Log Filter/Select/Display/Export Log Environmental Specifications Item Description Operating Temperature
-40C to 55C Storage Temperature
-40C to 70C Item Description Operating Humidity 5% to 95%
Ingress Protection Rating IP65 6. Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body. 1
This product uses the FCC Data API but is not endorsed or certified by the FCC