FCC ID: 2AAED-R9861510 ClickShare CS-100

CS-100 User guide R5900024/00 21/12/2014 Barco NV President Kennedypark 35, 8500 Kortrijk, Belgium Phone: +32 56.23.32.11 Fax: +32 56.26.22.62 Support: www.barco.com/en/support Visit us at the web: www.barco.com Printed in China Copyright All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco. Trademarks Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufacturers. Guarantee and Compensation Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints. The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justied notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross negligence or part of Barco. If the purchaser or a third party carries out modications or repairs on goods delivered by Barco, or if the goods are handled incorrectly, in particular if the systems are operated incorrectly or if, after the transfer of risks, the goods are subject to inuences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either. The environmental conditions as well as the servicing and maintenance regulations specied in this manual must be complied with by the customer. Barco ClickShare End-User License Agreement (EULA/Software License) PLEASE READ THIS DOCUMENT CAREFULLY BEFORE OPENING OR DOWNLOADING AND USING SOFTWARE OR HARDWARE PROVIDED TO YOU BY BARCO AS IT CONTAINS THE TERMS AND CONDITIONS BY WHICH BARCO OFFERS TO LICENSE THE SOFTWARE. BY OPENING THE SOFTWARE PACKAGE, OR USING THE HARDWARE IN WHICH THE SOFTWARE IS EMBEDDED, YOU AGREE TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT. The Software as supplied by BARCO is licensed, not sold to you, on a non-exclusive basis for use only under the terms of this license, and BARCO reserve all rights not expressly granted to you. You may own the carrier on which the Software is provided, but the Software is owned and copyrighted by BARCO or by third party suppliers. Your license confers no title or ownership and is not a sale of any rights in the Software or its documentation. By installing, executing and/or using the Software, either as initial version or as an upgrade, update, patch or enhancement of a prior release, this Software License shall supersede any terms and conditions previously agreed upon (whether or not in writing) between Barco and you with respect to the subject matter of this Software License and such previous terms shall from the date hereof cease to have any force or effect; provided, however that this Software License shall not be construed as a renunciation, discharge or waiver of any right or remedy provided in any terms and conditions previously agreed upon with respect to a failure of either party to perform any of its obligations under any terms and conditions previously agreed upon. Software Specications The Software contains the following software products: ClickShare Software License Terms 1. 2. 3. 4. 5. This Software License is between you and BARCO NV, a corporation organized and existing under the laws of Belgium registered under number BE 0473.191.041, Commercial Companies Register of Kortrijk, having its registered ofce President Kennedypark, 35 at B-8500 Kortrijk, Belgium ("Barco") for the use of the Software. You hereby undertake to inform all users authorized by you to make use of the computing device on which the Software is loaded/in-

stalled (Authorized Users) of the terms of this Software License and to bind all Authorized Users to accept all such terms of this Software License as applies to them. Barco grants you a limited, non-exclusive, non-assignable, non-transferable user license (without the right to grant sublicenses). Unless specically agreed upon otherwise between you and Barco or unless specically allowed by the Software (or its DRM man-

agement) itself, i) the license under this Software License applies to one (1) copy of the Software to be used on one single computing device and ii) installation on a computing device that may be concurrently accessed by more than one user shall not constitute a permitted use and a separate license is required for each active user connected to a computing device on which the Software is being used. You and Authorized Users are entitled to use the Software for the purposes and in the manner set out in this Software License (and documentation), but neither you nor any Authorized User are entitled to: (i) sell or grant a security interest in the Software to other parties in any way, or to rent, lease or sub-license the Software to others without the express prior written consent of Barco; or (ii) exploit the Software or any of its component parts for any commercial purpose, other than use by you and/or Authorized Users of the Software. Neither you nor any Authorized User may, whether in whole or in part, copy, translate, reverse engineer, derive source code from, modify, disassemble, decompile, create derivative works based on the Software, or remove any proprietary notices or labels on the Software, save as may be permitted by law or this Software License, without the prior consent, in writing, of Barco. Barco (and Barcos licensors, as appropriate) retain ownership of all intellectual property rights in the Software and any copies you or any Authorized User may make of such Software. The Software is protected by national copyright laws, international copyright treaties and conventions, and other applicable laws. All rights not expressly licensed to you in this Software License are reserved to Barco and Barcos licensors, as appropriate. The Software contains certain other licensed materials and Barcos licensors may protect their rights in the event of any violation of this Software License. Barco shall hold you harmless, defend and indemnify you from and against direct damages, losses and expenses arising from in-

fringement or alleged infringement of any patent, trademark or copyright of such third party by the license and the right to install the Software as permitted by this Software License and settle at its sole expense any amounts awarded in a nal judgment or settlement resulting therefrom, under the condition that (i) you promptly notify Barco in writing after a claim has been asserted against you or the commencement of any claim, action, suit or proceeding (whichever is the earlier), and (ii) Barco shall be allowed to assume sole control of the defense and any settlement negotiations related to any claim, action, suit or proceeding, and (iii) you shall not negotiate, settle or compromise any claim, action, suit or proceeding without the prior written consent of Barco and (iv) you, at your cost, shall cooperate with Barco and provide assistance and support, as may reasonably be required by Barco, in connection with the defense and any settlement negotiations related to any claim, action, suit or proceeding. Barco shall have no indemnity obligation for any Software, or any portion thereof, (i) that is based on specications, drawings, models or other data furnished by you or, (ii) that is not provided by Barco or, (iii) that is modied, in spite of the prohibition for you to modify the software or, (iv) to the extent that you continue allegedly infringing activity after having been provided modications that avoid the alleged infringement, or (v) where the use of the Software, or the combination or thereof with other Software, processes or materials or the distribution thereof rather than the Software itself is the primary cause of an alleged infringement. In case it has been determined by a nally awarded judgment that Barco infringed or misappropriated such third party rights or earlier, at Barcos discretion, it may, at its option and cost, (i) modify the Software in such a way that it shall not infringe upon or misappropriate the rights of the third party or (ii) obtain for you a license or other right to use the rights allegedly infringed or (iii) replace the Software in question with non-infringing Software. The remedies set forth in this paragraph shall constitute your sole and exclusive remedy and Barcos sole and exclusive liability for a third party claim that the Software infringes or misappropriates any intellectual property right of a third party. The duration of this Software License will be from the date of your acceptance (as set forth above) of the Software (whereby you ac-

knowledge that use of the Software implies acceptance), with no termination date, unless otherwise specied. You may terminate this Software License at any time by destroying all copies of the Software then in your possession and returning all associated materials and documentation, to Barco or the appointed Barco reseller that sold or provided these to you. Barco may terminate this Software License forthwith by informing you at any time if you and/or any Authorized User are in breach of any of the Software Licenses terms. 6. 7. 8. 9. YOU UNDERSTAND THAT THE SOFTWARE IS BEING PROVIDED TO YOU "AS IS". BARCO DOES NOT MAKE NOR INTENDS TO MAKE ANY WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED AND SPECIFICALLY DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS, FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF INTELLEC-

TUAL PROPERTY AND DOES NOT WARRANT THAT THE SOFTWARE WILL BE FREE FROM ERRORS OR THAT SUCH ERRORS WILL BE CORRECTED BY BARCO AND YOU ARE SOLELY RESPONSIBLE FOR ALL COSTS AND EXPENSES ASSOCIATED WITH RECTIFICATION, REPAIR OR DAMAGE CAUSED BY SUCH ERRORS. YOU ALSO ACKNOWLEDGE AND AGREE THAT:

BARCO ACCEPTS NO LIABILITY FOR ANY DAMAGES, LOSSES OR CLAIMS YOU OR ANY THIRD PARTY MAY SUFFER AS A RESULT OF YOUR USE OF THE SOFTWARE. IN JURISIDCTIONS WHERE BARCOS LIABILITY CANNOT BE EXCLUDED, BARCOS LIABILITY FOR DIRECT DAMAGES SHALL BE LIMITED TO AN AMOUNT OF 250 EURO IN THE AGREGATE (OR TO THE MAXIMUM EXTENT PERMITTED BY LAW WHERE NO FURTHER EXCLUSION IS LEGALLY ALLOWED). TO THE MAXIMUM EXTENT PERMITTED BY LAW, IN NO EVENT WILL BARCO BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL LOSS OR DAMAGES OF ANY KIND WHICH MAY ARISE OUT OF OR IN CON-

NECTION WITH THE SOFTWARE, THIS SOFTWARE LICENSE OR THE PERFORMANCE OR PURPORTED PERFORMANCE OF OR FAILURE IN THE PERFORMANCE OF BARCOS OBLIGATIONS UNDER THIS SOFTWARE LICENSE OR FOR ANY ECO-

NOMIC LOSS, LOSS OF BUSINESS, CONTRACTS, DATA, GOODWILL, PROFITS, TURNOVER, REVENUE, REPUTATION OR ANY LOSS ARISING FROM WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION OF THE SOFTWARE AND ANY AND ALL OTHER COMMERCIAL DAMAGES OR LOSSES WHICH MAY ARISE IN RESPECT OF USE OF THE SOFTWARE, EVEN IF BARCO HAS BEEN ADVISED OF THE POSSIBILITY OF THEIR OCCURRENCE. YOU HEREBY AGREE TO INDEMNIFY, KEEP INDEMNIFIED, DEFEND AND HOLD HARMLESS BARCO AND BARCOS AFFILI-

ATES AND SUBSIDIARIES FROM AND AGAINST ANY AND ALL ACTIONS, PROCEEDINGS, LIABILITY, LOSS, DAMAGES, FEES AND COSTS (INCLUDING ATTORNEYS" FEES), AND OTHER EXPENSES INCURRED OR SUFFERED BY BARCO ARISING OUT OF OR IN CONNECTION WITH ANY BREACH BY YOU OF THE TERMS OF THIS SOFTWARE LICENSE. You shall treat as condential all information obtained from the other pursuant to this Software License which is marked "condential"

or the equivalent or has the necessary quality of condence about it and shall not divulge such information to any persons without Barcos prior written consent provided that this Paragraph 7 shall not extend to information which was rightfully in the possession of you prior to the commencement of the negotiations leading to this Software License, which is already public knowledge or becomes so at a future date (otherwise than as a result of a breach of this paragraph 7), is required to be disclosed by law or which is trivial or obvious. You are aware of and ensure to comply with the provisions of this paragraph 7. The foregoing obligations as to condentiality shall survive any termination of this Software License. You will remain responsible for the maintenance of your hardware, operating system, the functioning of your network and in keeping your systems virus-free. You acknowledge that the Software is a complex computer software application, and that the performance thereof may vary depending hardware platform, software interactions and conguration. You acknowledge that the Software is not designed and produced specically to meet your specic requirements and expectations and the selection of the Software by you is entirely your own choice and decision. For the avoidance of doubt, nothing in this Software License shall impose any obligation on Barco to provide support services (on the Software or any other hardware or software product). This Software License is the only understanding and agreement between you and Barco for use of the Software by you and/or Autho-

rized Users. The Software License supersedes all other communications, understandings or agreements we had prior to this Software License (with the exception of any continuing condentiality agreement) although nothing in this Software License purports to exclude liability for fraudulent misrepresentation. You may not export or re-export the Software or any copy or adaptation in violation of any applicable laws or regulations. This Software License shall not be altered, amended or varied. If any provision of this Software Li-

cense is determined to be illegal, void or unenforceable, or if any court of competent jurisdiction in any nal decision so determines, this Software License shall continue in full force save that such provision shall be deemed to be deleted with effect from the date of such decision, or such earlier date, and shall be replaced by a provision which is acceptable by law and which embodies the intention of this Software License a close as possible. 10. You acknowledge that this Software may be subject to U.S. or other governments Export Jurisdiction. You agree to comply with all applicable international and national laws that apply to the Software, including the U.S. Export Administration Regulations, as well as end-user, end-use, and destination restrictions issued by the U.S. or other governments. 11. Barco shall be entitled to sub-contract all or any of Barcos obligations hereunder to a third party and/or any of Barcos afliated companies. 12. The construction, validity and performance of this Software License shall be governed in all respects by the laws of Belgium without recourse to its conict of law principles. All disputes arising in any way out of or affecting this Software License shall be subject to the exclusive jurisdiction of the courts of Kortrijk, without prejudice to enforcement of any judgment or order thereof in any other jurisdiction. The United Nations Convention on Contracts for the International Sale of Goods (the "Convention") shall not apply to this Software License, however, if the Convention is deemed by a court of competent jurisdiction to apply to this Software License, Barco shall not be liable for any claimed non-conformance of the Software under Article 35(2) of the Convention. Trademarks Software License Terms Brand and product names mentioned in relation to the Software may be trademarks, registered trademarks or copyrights of their respective

(third party) holders. All such brand and product names mentioned in relation to the Software serve as comments or examples and are not to be understood as advertising for the products or their manufacturers. Privacy Policy You acknowledge and agree that the Software is gathering technical information about the functionality of the products which are connected through the Software (Functional Information) and that Barco may make use of such Functional Information (with the exclusion of any personal data) for any reason Barco sees t, including but not limited to providing services to you / your organization, allowing third party to access to such Functional Information and/or to provide services to you / your organization . You hereby explicitly give consent that Barco may gather, access, preserve, and/or disclose the personal data you provide to us (e.g. connected with your account allowing for the gathering of Functional Information as well as any content associated with that account) as well as personal information we receive from you through the use of the Software:

For the benet of the business purposes of Barco and/or its afliates;

In order to provide, maintain, protect and/or improve the Software and to develop new software;

For administration of the relationship between you, your organization and Barco and/or its afliates ;

For any other legitimate purpose (including i) direct marketing purposes from Barco, its afliates or selected third parties, and ii) allowing third parties to provide services to you related to the Software);

if required to do so by law or in a good faith belief that such access preservation or disclosure is reasonably necessary to:

- Satisfy any applicable law, regulation, legal process or enforceable governmental request;

- Enforce this Software License, including investigation of potential violations hereof;

- Detect, prevent, or otherwise address fraud, security or technical issues (including, without limitation, the ltering of spam);

- Protect against imminent harm to the rights, property or safety of Barco, its users or the public as required or permitted by law. Transmissions over various networks;

Changes to conform and adapt to technical requirements of connecting networks, devices and/or services. Barco shall not process any sensitive information whatsoever, including but not limited to medical information. You understand that the technical processing and transmission of or by the Software, including your content, may involve:

You hereby explicitly give consent that Barco may export your personal data to any country worldwide, especially to any country where Barco and/or its afliates have infrastructure, or where a third party is making available infrastructure to Barco and/or its afliates, to process personal data. Barco fully adheres to the EU Directive 95/46/EC on the protection of individuals with regard to the processing of personal data and the free movement of such data, as implemented in the local EU member states. In accordance with these regulations, you have a right of access to, and rectication of, your personal data. You may exercise these rights by contacting Barco. Open Source Software provisions:

This product contains software components released under an Open Source license. A copy of the source code is available on request by contacting your Barco customer support representative. EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTATION ARE PROVIDED "AS IS" WITH-

OUT EXPRESS OR IMPLIED WARRANTY INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTOR BE LIABLE FOR DIRECT, INCIDENTAL, SPECIAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POS-

SIBILITY OF SUCH DAMAGES, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIA-

BILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS OPEN SOURCE SOFTWARE. MORE INFORMATION/DETAILS IS TO BE FOUND IN EACH SPECIFIC OPEN SOURCE LICENSE. Copyright on each Open Source Software component belongs to the respective initial copyright holder, each additional contributor and/or their respective assignee(s), as may be identied in the respective documentation, source code, README le, or otherwise. You shall not remove or obscure or otherwise alter the respective copyrights. You acknowledge living up to the conditions of each separate Open Source Software license. In the development of the Software, the following Open Source Software components have been used (an updated list may be made available through the (customer section of the) Barco website or other (online) means):

Open Source component acl acpid attr alsa-lib alsa-utils Open Source License http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/lgpl.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/lgpl.html Open Source component alsa-plugins avahi Bootstrap (3.1.1) bootstrap-dialog bootstrap-slider.js v2.0.0 busybox Chart.js Datepicker for Bootstrao (1,6,0-dev) dropbear fakeroot coreutils crda cron Crypto++

dbus dhcpd dm-crypt dmidecode e2fsprogs eglibc ethtool express FFmpeg freetype gdbserver gmp grub gstreamer hdparm hostapd HTML5 Shiv 3.7.2 i18next (1.10.0) i2c-tools iftop imx-bootlets iperf iproute2 iptables Open Source License http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/lgpl.html http://www.gnu.org/licenses/lgpl.html https://github.com/twbs/bootstrap/blob/master/LICENSE https://github.com/twbs/bootstrap/blob/master/LICENSE http://www.apache.org/licenses/LICENSE-2.0 http://opensource.org/licenses/GPL-2.0 https://github.com/nnnick/Chart.js/blob/master/LICENSE.md http://www.apache.org/licenses/LICENSE-2.0 http://opensource.org/licenses/mit-license.php http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/gpl.html http://opensource.org/licenses/ISC http://opensource.org/licenses/ISC http://www.cryptopp.com/License.txt http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://opensource.org/licenses/ISC http://creativecommons.org/licenses/by-sa/3.0/

http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html http://www.gnu.org/licenses/lgpl.html http://www.gnu.org/licenses/gpl.html http://opensource.org/licenses/MIT http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html http://freetype.sourceforge.net/FTL.TXT http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/lgpl.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/lgpl.html http://opensource.org/licenses/BSD-3-Clause http://opensource.org/licenses/BSD-3-Clause http://github.com/aFarkas/html5shiv/blob/master/MIT%20and%20GPL2%20licenses.md https://opensource.org/licenses/MIT http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/gpl.html http://opensource.org/licenses/BSD-3-Clause http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/old-licenses/gpl-2.0.html Open Source component iw Jasny Bootstrap (3.1.3) jQuery Form Plugin (3.51.0-2014.06.20) jQuery JavaScript Library (1.11.3) jQuery Password Strength plugin for Twitter Bootstrap jQuery Upload File Plugin (4.0.8) jQuery Validation Plugin (1.13.1) kobs-ng libarchive libav libavutil libcap2 libdaemon0 libdrm2 libexpat1 libfontcong1 libfontenc1 libgcc1 libgcrypt11 libglib-2 libgnutls26 libgpg-error0 libjpeg-turbo libjpeg8 libnl2 libNotify libnss-mdns libpam libpcap libpcre0 libpixman-1-0 libpng12-0 libpopt0 libresample Open Source License http://opensource.org/licenses/BSD-3-Clause http://www.apache.org/licenses/LICENSE-2.0 https://github.com/malsup/form#copyright-and-license https://jquery.org/license/

https://github.com/ablanco/jquery.pwstrength.bootstrap/blob/master/GPL-LICENSE.txt https://github.com/ablanco/jquery.pwstrength.bootstrap/com-

mit/19480555e8c7c2f417d78a78dac63056fa221f6a https://github.com/hayageek/jquery-upload-le https://opensource.org/licenses/MIT http://www.gnu.org/licenses/gpl.html http://opensource.org/licenses/bsd-license.php http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html http://opensource.org/licenses/MIT http://opensource.org/licenses/MIT http://opensource.org/licenses/BSD-3-Clause http://opensource.org/licenses/BSD-3-Clause http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/lgpl.html http://www.gnu.org/copyleft/fdl.html http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html http://www.gnu.org/licenses/lgpl.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/lgpl.html http://www.gnu.org/copyleft/fdl.html http://opensource.org/licenses/BSD-3-Clause BSD like licensee http://www.gnu.org/licenses/lgpl.html https://wiki.gnome.org/FoundationBoard/Resources/LicensingAgreement http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://opensource.org/licenses/BSD-3-Clause http://opensource.org/licenses/BSD-3-Clause http://changelogs.ubuntu.com/changelogs/pool/main/p/pixman/pixman_0.10.0-

0ubuntu1/libpixman-1-0.copyright http://www.libpng.org/pub/png/src/libpng-LICENSE.txt http://opensource.org/licenses/MIT http://www.gnu.org/licenses/lgpl.html Open Source component libsm6 libstdc++6 libswscale libtalloc2 libusb libva libX11 libXdamage libXext libXxes libXinerama libxml2 libXrender libXtst libz1 lighttpd linux lmsensors logrotate makedevs memtest86plus mesa modernizr (3.1.0) module-init-tools modutils monit ncurses netbase node.js openssl openssh-sftp-server opkg passport passport-http pciutils perl php procps pulseaudio Open Source License http://metadata.ftp-master.debian.org/changelogs//main/libs/libsm/libsm_1.2.2-1_copyright http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html http://www.gnu.org/licenses/lgpl.html http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html Copyright (c) 2011, Advanced Micro Devices, Inc. All rights reserved. http://opensource.org/licenses/MIT http://opensource.org/licenses/MIT http://opensource.org/licenses/MIT http://opensource.org/licenses/MIT http://opensource.org/licenses/MIT http://opensource.org/licenses/MIT http://opensource.org/licenses/MIT http://opensource.org/licenses/MIT Free license http://opensource.org/licenses/BSD-3-Clause http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/gpl.html http://opensource.org/licenses/MIT https://opensource.org/licenses/MIT http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/gpl.html http://opensource.org/licenses/MIT http://www.gnu.org/licenses/old-licenses/gpl-2.0.html https://raw.github.com/joyent/node/v0.10.26/LICENSE http://www.openssl.org/source/license.html http://opensource.org/licenses/BSD-3-Clause http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://opensource.org/licenses/MIT http://opensource.org/licenses/MIT http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://perldoc.perl.org/perlartistic.html http://www.gnu.org/licenses/old-licenses/gpl-1.0.html http://www.php.net/license/3_01.txt http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/lgpl.html Open Source component qt read-edid Respond.js rockbox-imxtools rsync (<3.0.0) rsync (>=3.0.0) rsyslog splashutils sprintf-js sscep strace sysfsutils sysvinit tcpdump Timepicker Component for Twitter Bootstrap ttf-arphic-uming ttf-dejavu-common ttf-dejavu-sans ttf-dejavu-sans-mono ttf-sazanami-gothic ttf-sazanami-mincho ttf-un-fonts u-boot uClibc udev update-modules update-rc usbutils util-linux-ng wireless_tools wpa_supplicant xserver-xorg xvba-video zeroconf Open Source License http://doc.qt.io/qt-5/lgpl.html Free license https://github.com/scottjehl/Respond/blob/master/LICENSE-MIT http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/gpl.html https://opensource.org/licenses/BSD-3-Clause https://github.com/certnanny/sscep/blob/master/COPYRIGHT http://opensource.org/licenses/BSD-3-Clause http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://opensource.org/licenses/BSD-3-Clause https://opensource.org/licenses/MIT http://ftp.gnu.org/non-gnu/chinese-fonts-truetype/LICENSE http://dejavu-fonts.org/wiki/License http://dejavu-fonts.org/wiki/License http://dejavu-fonts.org/wiki/License https://osdn.jp/cvs/view/efont/sazanami/README http://metadata.ftp-master.debian.org/changelogs//main/t/ttf-sazanami/ttf-

sazanami_20040629-8_copyright (translation) https://osdn.jp/cvs/view/efont/sazanami/README http://metadata.ftp-master.debian.org/changelogs//main/t/ttf-sazanami/ttf-

sazanami_20040629-8_copyright (translation) http://www.gnu.org/licenses/gpl.txt http://www.denx.de/wiki/U-Boot/Licensing http://www.gnu.org/licenses/lgpl.html http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/gpl.html http://www.gnu.org/licenses/gpl.html http://opensource.org/licenses/BSD-3-Clause http://opensource.org/licenses/MIT http://www.gnu.org/licenses/old-licenses/gpl-2.0.html http://www.gnu.org/licenses/gpl.html EN55022-CISPR22 Class B ITE (Information Technology Equipment) This is a class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Re-orientation of the receiving antenna for the radio or television. Relocate the equipment with respect to the receiver. Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits. Fasten cables connectors to the equipment by mounting screws. If this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the following measures :

Federal Communication Commission Interference Statement You are cautioned that changes or modications not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen-

erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. You may also nd helpful the following booklet, prepared by the FCC: "How to Identify and Resolve Radio-TV Interference Problems." This booklet is available from the U.S. Government Printing Ofce, Washington D.C. 20402. Changes and Modications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commissions rules. In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio & television reception. FCC RF Radiation Exposure Statement: This device is capable of operating in 802.11a mode. For 802.11a devices operating in the frequency range of 5.15 - 5.25 GHz, they are restricted for indoor operations to reduce any potential harmful interference for Mobile Satellite Services (MSS) in the US. WIFI Access Points that are capable of allowing your device to operate in 802.11a mode (5 .15 - 5.25 GHz band) are optimized for indoor use only. If your WIFI network is capable of operating in this mode, please restrict your WIFI use indoors to not violate federal regulations to protect Mobile Satellite Services. Base Unit FCC ID: 2AAED-R9861510 Button FCC ID (model R9861006D01): XF6-RS9110N1103 Button FCC ID (model R9861500D01): 2AAED-R9861500D01 ClickShare Button R9861500D01 has been tested and meets the FCC RF exposure guidelines.The maximum SAR value reported is 0.915W/kg. Canada, Industry Canada (IC) Notices This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Information The radiated output power of the Barco Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Barco Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. Base Unit IC ID: IC: 9393B-R9861510 Button IC ID (model R9861006D01): 8407A-RS9110N1103 Button IC ID (model R9861500D01): 9393B-R9861500D01 IC Antenna statement Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter 9393B-R9861510 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Type: Dipole Maximum Peak Gain: 2 dBi Impedance: 50 Ohm Canada, avis dlndustry Canada (IC) Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Informations concernant lexposition aux frquences radio (RF) La puissance de sortie mise par lappareil de sans l Barco est infrieure la limite dexposition aux frquences radio dIndustry Canada

(IC). Utilisez lappareil de sans l Barco de faon minimiser les contacts humains lors du fonctionnement normal. IC ID Unit de Base: 9393B-R9861510 IC ID Button (modle R9861006D01): 8407A-RS9110N1103 IC ID Button (modle R9861500D01): 9393B-R9861500D01 Dclaration dantenne dIndustrie Canada (IC) Conformment la rglementation dIndustrie Canada, le prsent metteur radio peut fonctionner avec une antenne dun type et dun gain maximal (ou infrieur) approuv pour lmetteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique lintention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la puissance isotrope rayonne quivalente

(p.i.r.e.) ne dpasse pas lintensit ncessaire ltablissement dune communication satisfaisante. Le prsent metteur radio 9393B-R9861510 a t approuv par Industrie Canada pour fonctionner avec les types dantenne numrs ci-dessous et ayant un gain admissible maximal et limpdance requise pour chaque type dantenne. Les types dantenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour lexploitation de lmetteur. Type: Dipole Gain maximum: 2 dBi Impdance: 50 Ohm TABLE OF CONTENTS Tableofcontents 2. 1. Introduction ........................................................................................................ 3 Versions of the product . . . . . . . . . . . . . . . 3 1.1 1.2 About this guide . . . . . . . . . . . . . . . .. 3 1.3 Symbols and fonts . . . . . . . . . . . . . . . . 4 Introduction to CS-100 ........................................................................................... 5 About the CS-100 . . . . . . . . . . . . . . . . . 5 2.1 2.2 About the Base Unit . . . . . . . . . . . . . . . . 6 2.3 About the Button. . . . . . . . . . . . . . . .. 7 2.4 Mobile Device Support . . . . . . . . . . . . . . . 8 3. Getting started ..................................................................................................... 9 3.1 Activating the base unit. . . . . . . . . . . . . . .. 9 3.2 Basic Use . . . . . . . . . . . . . . . . . 9 3.3 User Interface. . . . . . . . . . . . . . . .. 11 3.4 Capture more . . . . . . . . . . . . . . . .. 12 Shared desktop: primary - extended. . . . . . . . . . . . . 13 3.5 Audio conguration .. . . . . . . . . . . . . . . 15 3.6 3.7 Pairing . . . . . . . . . . . . . . . . . . 17 4. Troubleshooting ...................................................................................................19 Basic Troubleshooting. . . . . . . . . . . . . . . 19 5. Environmental information ......................................................................................21 5.1 Disposal information. . . . . . . . . . . . . . . 21 5.2 Rohs compliance . . . . . . . . . . . . . . . . . 21 Production address .. . . . . . . . . . . . . . . 22 5.3 5.4 Importers contact information . . . . . . . . . . . . . . 22 4.1 R5900024 CS-100 21/12/2014 1 Tableofcontents 2 R5900024 CS-100 21/12/2014 1.Introduction 1. INTRODUCTION Overview Versions of the product About this guide Symbols and fonts 1.1 Versions of the product Regional versions Depending on the location where you buy the CS-100 product, the Base Unit and accessories are regionalized. By the time of release of this manual, 3 regional versions of CS-100 are available:

Europe & Japan North America China The regional version of your CS-100 cannot be changed. That means that you cannot use it in another region. For more information on the regional variants, refer to the CS-100 Installation Guide. 1.2 About this guide This manual Partnumber R5900024 Description User Guide Level User Available System documentation This guide is part of the documentation set describing the CS-100 product. Guide User Guide Installation Guide Safety Guide Service Guide Button Guide Recycling Manual API Guide Article number R5900024 R5900022 R5900031 R5900026 R5900007 R5900028 R5900018 A printed copy of the Safety Guide and an electronic version on USB stick of the user and installation guide is included in the CS-100 box at purchase. Always check for the latest version of the manual on www.barco.com/clickshare Click on Visit the ClickShare product page and go to tab Downloads.. Depending on the CS-100 version, some graphics might be different to the ones used in this manual. This however does not have any effect to the functionality. R5900024 CS-100 21/12/2014 3 1.Introduction The User Guide describes how to use your CS-100. It also contains a basic troubleshooting part where you can search for a solution when a problem occurs. 1.3 Symbols and fonts Symbol overview The following icons are used in the manual :

Caution Warning Info, term denition. General info about the term Note: gives extra information about the described subject Tip: gives extra advice about the described subject Font overview Buttons are indicated in bold, e.g. OK. Menu items are indicated in italic. Step related notes, tips, warnings or cautions are printed in italic. Procedure related notes, tips, warnings or cautions are printed in bold between 2 lines preceded by the corresponding icon. 4 R5900024 CS-100 21/12/2014 2. INTRODUCTION TO CS-100 2.IntroductiontoCS-100 Overview About the CS-100 About the Base Unit About the Button Mobile Device Support 2.1 About the CS-100 CS-100 sets CS-100 makes connecting to the meeting rooms video system a matter of clicking a Button. This CS-100 only helps the presenter get the presentation on-screen in a second, but it also allows the other people in the meeting to participate more actively. The result is enhanced meeting efciency and better decision-making. At the moment 3 different sets are available on the market. Each set is sold in its specic region and it can only be used in that specic region. Components CS-100 set A standard CS-100 set consists of a Base Unit and 1 Button. Depending on the location where you buy the product, the software of the Base Unit is different. If needed, you can buy additional Buttons. 1 2 Image 2-1 1 2 Base unit Button Accessories included Depending on the country where you buy the product, the following regionalized accessories are also included in the CS-100 box. Regional version R9861510xx1 Contains Accessories included R9861510 1x R9861500D01 DC adapter with AC clips type A, C, G, I USB stick with user documentation Printed safety manual Contact your local sales representative for the correct regional variant to be used in your country. 1. xx=EU, CN, NA, R5900024 CS-100 21/12/2014 5 2.IntroductiontoCS-100 2.2 About the Base Unit Base Unit functionality The Base Unit receives the wireless input from the Buttons and controls the content of the meeting room display and the sound of the meeting rooms audio system. The Base Unit can be inside a cabinet in the meeting room, or put on the meeting room table or mounted on a wall. Check the Installation Guide for instructions on how to install the Base Unit. 1 Image 2-2 1 2 3 Table 2-3 USB port Status LED ring Power Button 2 3 USB Port The USB port is used to update the software of both the Base Unit and the Buttons. When plugging in the Button into the Base Unit, the Button is paired to the Base Unit. The Base Unit checks whether the software and rmware of the Button is up to date. If not, the Base Unit updates the software and/or rmware. Status LED ring The color of the LED ring around the power button of the Base Unit gives information on the status of the system. LEDs behavior static red blinking white breathing white static white red blinking dark Explanation receiving content from the Buttons and streaming towards the display. pairing and software update of the Button is done. You can now unplug the Button from the Base Unit. during the rst phase of the Base Unit boot process. system is starting up (during the second phase) Button pairing is in progress software update of the Base Unit ECO standby mode networked standby mode awake and ready (i.e. showing the welcome message on the display) pairing is done an error occurred deep standby/off Power button The button at the front of the Base Unit has a power on/off function once the Base unit is powered. When the system is powered on, a push makes the system to shut down and power off. When the system is shut down, a push triggers the system to start up. 6 R5900024 CS-100 21/12/2014 2.3 About the Button Button functionality A Button contains three main functional components. 1 2 3 2.IntroductiontoCS-100 Image 2-3 The Button 1 2 3 Table 2-5 USB connector Button LED ring Handle the Button cable with care. Rough handling might cause defects. USB connector Using the USB connector the Button can be plugged into a laptop (for sharing your screen) or in the Base Unit (for pairing the Button to the Unit or updating its software). Button Click the Button to display the content of the laptops screen on the meeting room display. Clicking the Button during the meeting will toggle the sharing of the screen. LED ring The LED ring indicates the current status of your CS-100. LEDs behavior white blinking static white static red red blinking off (no light) Explanation the Button is plugged in the laptop and initializing or waiting for the user to start the ClickShare application. pairing/software update of the Button in the Base Unit is in progress. ClickShare is ready to start sharing your screen. pairing is done. You can now unplug the Button from the Base Unit. sharing your screen with the display. pairing and software update is done. You can now unplug the Button from the Base Unit. an error occurred. the Button is not or not properly inserted into the USB port. the Button might be defective. the USB port or computer might be defective. R5900024 CS-100 21/12/2014 7 2.IntroductiontoCS-100 2.4 Mobile Device Support Overview The below list of Apps are supported by ClickShare and can be installed on your mobile device from Google Play or Apple App Store. Before you can use your mobile device with ClickShare, you have to connect the mobile device Wi-Fi with the ClickShare Base Unit Wi-Fi. Follow the instructions as given in your mobile device user guide. App ClickShare App Used on iOS Android Logo MirrorOp Sender for Galaxy Galaxy mobile devices 8 R5900024 CS-100 21/12/2014 3.Gettingstarted 3. GETTING STARTED Overview Activating the base unit Basic Use User Interface Capture more Shared desktop: primary - extended Audio conguration Pairing 3.1 Activating the base unit About power mode The Base Unit is powered via an external power adapter. Once connected, the Base Unit is automatically switched in standby mode. For more information about power connection, see CS-100s installation manual. On and off 1. Push the button shortly. Image 3-1 Standby button When the Base Unit was on, it goes out When the Base Unit was off, it starts up. 3.2 Basic Use Basic functionality When entering a meeting room equipped with ClickShare and if the display is not in screensaver mode, the ClickShare wallpaper is shown on the display. The content of the wallpaper depends on the setup. Starting to use ClickShare is now very simple. To start using ClickShare 1. Take a Button and Insert the Button into a USB port of your laptop. R5900024 CS-100 21/12/2014 9 3.Gettingstarted Image 3-2 The LEDs of the Button start ashing white. On your laptop a new drive appears. Two situations are possible now:

- A launcher is preinstalled on your laptop (downloaded from the Base Unit or Barco website, or deployed company-wide by your IT department). ClickShare is immediately available. You can continue with step 4. nothing is pre-installed. Continue with step 2.

-

2. Browse to and double-click the ClickShare drive on your laptop. Image 3-4 MAC environment Image 3-3 Windows environment 3. Double-click the ClickShare application. 10 R5900024 CS-100 21/12/2014 The ClickShare client software starts and its icon appears in the system tray. On a Windows computer:

On a Macintosh:

When the system is ready for use, a message appears close to the systray icon. 3.Gettingstarted Image 3-5 The LEDs of the Button are static white. 4. To share your screen on the display, click the Button. The LEDs of the Button become static red and your screen appears on the display. When audio is enabled on the ClickShare Base Unit, the audio of your laptop is also available on the audio output of the Base Unit and on the HDMI output, and it will be played via the meeting room audio system. The icon returns to the same state as in step 3. In the system tray, the ClickShare icon starts rotating. On Windows computers the icon changes into The name of the user logged on to the laptop which is sharing its content is briey shown in the bottom left corner of the added content. ClickShare automatically scales the content of your screen to the resolution of the meeting room display. The aspect ratio of your screen is maintained to make sure the proportions are correct. 5. To remove your content from the display, click the Button again. The LEDs of the Button become static white. 6. When leaving the meeting room, unplug the Button from your laptop. No trace of the ClickShare application is left on your laptop. 3.3 User Interface User Interface functionality After launching the client, the ClickShare icon appears in the system tray. ClickShare context menu The content of the context menu is related to the operating system. 1. Right-click the ClickShare icon in the system tray. The context menu appears. Image 3-6 Context menu 2. From the list, click the action you want to perform. R5900024 CS-100 21/12/2014 11 3.Gettingstarted Click Start sharing Show me fullscreen Settings... Pair Button Capture mode Shared desktop (only for Windows7 and Windows8) About ClickShare Client Exit To to show your screen on the display. to bring the content of your screen on the display full screen. select the way to connect. Via ClickShare Button or via a network connection to pair the connected Button with the Base Unit to choose to capture video with more

(slower performance) or less detail

(faster performance). to select primary or extended desktop to nd out the ClickShare software version. to close ClickShare. Result The LEDs of your Button become red. The screens of other users that were shown on the display disappear. Connected via Button or via network Button is ready for use. Tune video performance and quality Depending on the selection the primary or the extended display is displayed. Here you can nd more information on the ClickShare software version. The ClickShare icon disappears from the system tray and the LEDs of the Button start blinking white. 3.4 Capture more Only for Windows XP, Windows Vista and Windows 7 & 8. About capture more ClickShare is optimized for optimum video performance. Upon starting the client software it will disable Win7 Aero Glass to maximize video performance. Upon quitting the ClickShare applications your Aero Glass settings will be restored. Transparent alpha layers are by default not captured. Therefore some windows may not be shown or may appear different on screen. For example content of video players using overlays will not be shown. With "Capture More" selected, Win7 Aero Glass settings will be restored and capturing of alpha layers is enabled. video throughput may decrease a bit and more details will be captured. Default setting: Not checked. How to change 1. Right click on the ClickShare icon in the system tray (1). In this mode, Image 3-7 Change capture mode A context menu opens. 2. Click Capture More to toggle. 12 R5900024 CS-100 21/12/2014 3.Gettingstarted Checked: capture with more details but may have a lower performance. Not checked: capture will be faster but may lose some of the details Starting the client automatically in Capture More The Capture more mode can be started by default so that the Aero Glass settings are not disabled. To do so, an environment variable should be introduced in your windows. Ask you administrator or consult your windows documentation to nd out how to create. The following variable should be introduced :

Variable CLICKSHARE_CAPTUREMOREBYDEFAULT Value 1 3.5 Shared desktop: primary - extended Only for Window7 and Windows8 About shared desktop Depending on your selection, your primary screen or your extended screen will be captured and displayed via ClickShare. That extended screen can be a physical screen or a virtual screen. With extended desktop you can take advantage of both your laptop screen and the central meeting room display. Presentation notes or other material on primary screen will not be displayed to everyone. PC with virtual extended screen:

1 2 Image 3-8 Primary screen displayed on the PC, extended screen displayed on the meeting room display. 2 1 2 Image 3-9 PC with one extended screen connected. That extended screen will be captured and displayed on the meeting room display. R5900024 CS-100 21/12/2014 13 3.Gettingstarted 2 3 1 2 Image 3-10 PC with two extended screens connected. The rst extended screen, screen 2 will always be captured and displayed on the meeting room display. To know if your system supports the extended desk top feature, press Window key + P. It should bring up the following pop-up on screen:

Image 3-11 How to select 1. Right click on the ClickShare icon in the system tray (1). Image 3-12 Shared desktop selection A context menu opens. 2. Select Shared Desktop (2). 3. Select the desired setting (3). Primary : the primary PC screen is displayed on the meeting room display. Extended always the secondary screen is displayed on the meeting room display. 14 R5900024 CS-100 21/12/2014 Known issue Virtual Extended Desktop not supported on some Windows7 and Windows8 systems due to a problem in recent versions of the AMD graphical driver. Downgrade to an older version of the driver might resolve the issue but make sure the AMD driver updated above version 13.8 . 3.Gettingstarted 3.6 Audio conguration Audio conguration The connected user must control his own audio signal using the audio conguration of his computer. If he does not want to broadcast his audio signal, he has to mute audio on his computer. For some operating system, it is necessary to set ClickShare as your default output device. Once you unplug the Button, the default setting is switched back to the previous setting. Set ClickShare as default in Windows 7 1. Right click on the speaker icon in the system tray (1). Image 3-13 Speakers ClickShare, default 2. Click Playback devices (2). The Sound window opens on the Playback tab. 3. Select Speakers ClickShare (3) and click Set default (4). 4. Click Apply or OK to activate the new setting. Set ClickShare as default in Windows XP 1. Right click on the speaker icon in the system tray. R5900024 CS-100 21/12/2014 15 3.Gettingstarted Image 3-14 Speakers ClickShare, default 2. Click Adjust Audio Properties (1). The Sound and Audio Devices Properties window opens. 3. Select Audio tab (2). 4. Click on the drop down box in the Sound playback pane and select ClickShare (3).. 5. Click Apply or OK to activate the new setting. Set ClickShare as default on MAC 1. Click on the Apple logo on the menu bar (1) and select System Preferences.. .(2). 16 R5900024 CS-100 21/12/2014 3.Gettingstarted Image 3-15 Speakers ClickShare, default 2. Click on the Speaker icon (3). The Sound window opens. 3. Select the Output tab (4) and activate ClickShare (5). 3.7 Pairing Pairing of the Buttons with the Base Unit To be able to use a Button it should be assigned to the Base Unit you are using. This process is called pairing. By default, the two Buttons delivered with the CS-100 set are already paired to the specic Base Unit. In case you buy additional Buttons or when a Button should be assigned to another Base Unit, the Button needs to be paired (again). The Button software update runs in the background and will not impact users while using the system. If desired, this feature can be disabled in the Web Interface. When downgrading or updating to an older version of the Base Unit software the Buttons need to paired manually to update their software. A Button can only be paired to one Base Unit at a time. The Button will always make connection to the Base Unit it was last paired to. To pair a Button to the Base unit 1. Insert the Button in the USB port at the front of the Base Unit you are using. R5900024 CS-100 21/12/2014 17 3.Gettingstarted Image 3-16 Pair button Both the LEDs of the Button and the LEDs of the Base Unit are blinking white. This means pairing is in progress. The Base Unit automatically checks whether the software of the Button is up to date. If not, the Base Unit updates the Button software. This may take more time. During the pairing and update process, a small status bar is display. Image 3-17 Pairing message The result of the pairing process can be as follows:

- When the LEDs become static white, the Button is paired to the Base Unit, but no software update was needed. You can unplug the Button from the Base Unit.

- When the LEDs become static red, the Button is paired to the Base Unit and the software update has nished. You can unplug the Button from the Base Unit. Image 3-18 Pairing nished 2. Unplug the Button from the Base Unit. The Button is now ready for use. 18 R5900024 CS-100 21/12/2014 4. TROUBLESHOOTING 4.1 Basic Troubleshooting 4.Troubleshooting Problem solving In this chapter some problems that might occur while using CS-100 are listed. For each problem possible causes are given and a solution is proposed. If you cannot solve the problem yourself, please contact your local IT administrator. Problem Your screen is not shown on the display when pressing the Button. Cause You are the second person that wants to share the content to the display. Your screen is shown, but your audio is not playing on the meeting room audio system Your content is removed from the display and the LEDs of your Button are blinking white. Nothing is shown on the display at all. The ClickShare client software is not running. Your audio signal on your PC is muted Audio system of the meeting room is not switched on When using separate audio, audio cable is not connected Default speaker is not correctly set . Buttons are not re-paired after changing the audio setting on the web interface Connection to the display has been lost. The display is switched off. Wrong input is selected. The display cable is not connected

(correctly). The display does not recognize or is not able to display the Base Unit output resolution. The Base Unit is in standby mode. The Base Unit is powered off. The Buttons software is not compatible with that of the Base unit Solution The rst user has to push his button to remove his content so that a second user can share his content. or As second user, click and hold the Button to use te Show me function of ClickShare. Go to the ClickShare drive and run the software. Right click on the speaker icon and switch off the mute. Switch on the audio system of the meeting room. Check audio connection between the Base Unit (audio out, green connector) and the audio system of the meeting room. With a Button inserted, set ClickShare speaker as your default speaker. Re-pair the buttons. ClickShare tries to restore the connection automatically. If this fails, the LEDs of the Button start blinking red. You should unplug the Button from your laptop and start a new. Switch on the display. Select the correct input.

(Re)insert the display cable to the display and the Base Unit. You or an administrator should change the corresponding setting via the web interface. Briey push the standby button on the Base Unit or plug in a Button and run the ClickShare client software. Check if power adapter is connected to the Base unit and to the wall outlet. Re-pair and update the software of the Button by inserting it in the front USB port of Base Unit. R5900024 CS-100 21/12/2014 19 4.Troubleshooting Problem After inserting the Button into your laptop, you cannot nd the ClickShare drive. Cause No automatic refresh of drives. Bad connection at USB port on laptop. Windows tries to assign the ClickShare drive to an already reserved drive letter Some programs of Windows are not shown on the display. Use of overlays, 3D or hardware acceleration in the GPU. Solution Refresh the view on your laptop. Reconnect to the USB port. Try another USB port. Reboot your laptop. Use Microsoft Windows Disk Management to assign it to a free drive letter. Disable overlays or hardware acceleration in the GPU. Disable AeroGlass in Windows 7 Capture mode 20 R5900024 CS-100 21/12/2014 5. ENVIRONMENTAL INFORMATION 5.Environmentalinformation 5.1 Disposal information Disposal Information Waste Electrical and Electronic Equipment This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. For more information about recycling of this product, please contact your local city ofce or your municipal waste disposal service. For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee Disposal of batteries in the product This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separately from municipal waste. If the battery contains more than the specied values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical symbols will appear below the crossed-out wheeled bin symbol. By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects on the environment and human health. 5.2 Rohs compliance Turkey RoHS compliance Trkiye Cumhuriyeti: AEEE Ynetmeliine Uygundur.

[Republic of Turkey: In conformity with the WEEE Regulation]

RoHS Chinese Mainland RoHS RoHS Barco/

RoHSMCV According to the China Administration on Control of Pollution Caused by Electronic Information Products (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barcos product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section Limit Requirements of toxic substances in Electronic Information Products.

() Component Name Printed Circuit Assemblies

() Cables Hazardous Substances or Elements

(Pb)

(Hg)

(Cd)

(Cr6+)

(PBB)

(PBDE) x x 0 0 x x 0 0 0 0 0 0 21 R5900024 CS-100 21/12/2014 5.Environmentalinformation x x 0 0 0 0 x x 0 0 0 0 0 Chassis Power Supply Unit Paper Manuals SJ/T 11364 This table is prepared in accordance with the provisions of SJ/T 11364. O: SJ/T 11363-2006 . O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/T11363. X: SJ/T 11363-2006 . X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363. 0 0 0 0 0 EIPEFUP BarcoEFUP All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with the Electronic Information Products Pollution Control Labeling Standard of Chinese Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the photo) is based on the Standard of Electronic Information Products Environmental Friendly Use Period of Chinese Mainland. Image 5-1 5.3 Production address Factory Barco N.V. 12F, Citychamp Building, No. 12, Tai Yang Gong Zhong Lu, Chaoyang District, Beijing, P.R.C Made in information The made in country is indicated on the product ID label on the product itself. Production date The month and year of production is indicated on the product ID label on the product itself. 5.4 Importers contact information Contact To nd your local importer, contact Barco directly or one of Barcos regional ofces via the contact information given on Barcos web site, www.barco.com. 22 R5900024 CS-100 21/12/2014