S1801 Shopify Tap & Chip Reader User Manual

Package Contents Device USB cable Quick start guide X1 X1 X1 STEP 2 Search for Cube on smartphone/tablet.

** Please ensure that the Bluetooth function of your smartphone/tablet is ON before device pairing. Bluetooth ON Search Shopify S1801 OTA Temper Self Check Interity Fail Shopify S1801 Advanced mPOS Design Integrating Bluetooth EMV and NFC Card Reading Functions Application Download & Installation This device can support iOS and Android. 1. Please download the ocial application from app stores before operation. 2. Please follow app instructions to register and login for proper operation. 3. For any questions, please contact the ocial application developer or solution provider. Supported Operating System:

iOS, Android Quick Start Procedures Index & Accessories (Fig.1) EMV card reader LED status indicator NFC card reader Connect the USB Type-C charging cable to charge the device as shown to the right. APP DOWNLOAD Download the ocial application from APP Store or Google Play Store.

** Shopify S1801 is powered by an internal Lithium Polymer rechargeable battery pack that cannot be removed or replaced. Before first use, charging is required for approximately two to three hours. To prevent potential electrical damage to the Shopify S1801, it is recommended to use the USB Type-C cable provided with the packaging.**

Bluetooth Pairing STEP 1 Press power button to turn on Shopify S1801. Power button Reset button

(**please use paper clip for reset) USB Type-C port for charging STEP 3 Enter bluetooth pin on smartphone/tablet.

** Default bluetooth pin is printed on the back of Shopify S1801. After device is successfully paired, Shopify S1801 is ready to use. Now, you can follow the application instructions to start the transaction process, then insert or tap card to complete the transaction.

** If you are paying using an EMV card, please ensure that the EMV chip of the card is facing the right direction. If you are paying using an NFC card, please ensure you tap the NFC payment card or your device with your NFC wallet range on top of the NFC marking. within 4cm LED Status Indicators Power On Power O Idle FLASHING second and third light alternatively FLASHING rst and last red light First and last red light ON Battery Charging Status 0-10%

FLASHING rst red light 11-25%

FLASHING rst light 26-50%

FLASHING second light 51-79%

FLASHING third light 80-100%

FLASHING last light When power on, it is shown as below in rst four second Battery Level 0%

FLASHING rst red light 0-10%

First red light ON 11-25%

First light ON Show battery level for 4 seconds No action needed to power o No light status 26-50%

Two lights ON 51-79%

Three lights ON 80-100%

All lights ON EnterBluetooth Pin LED Status Indicators Cautions & Important Notes Troubleshooting Warranty NFC Operation Ready for Transaction Reading Card Information Card Reading Process Successfully Completed First light ON Lights COME ON in consecutive order All lights ON with BEEP sound EMV Operation Ready for Transaction When Card is Inserted Card Removal Detection First light ON Lights COME ON in consecutive order Leave all lights ON until card is removed Transaction Result Transaction Approved Transaction Failed/Error BEEP sound and FLASHING all lights 3 times Two BEEPS sound and rst red light ON Waiting for Connection Connected Bluetooth No Connection Reset Bluetooth Bluetooth Connection Ensure the device is fully charged before use. Please ensure the EMV chip of the card is facing the right direction when inserting card. The NFC card or mobile wallet should be tapped within 4 cm range on top of the reader mark. Dont drop, disassemble, tear, open, crush, bend, deform, puncture, shred, microwave, incinerate, paint or insert foreign object into the device. Doing any of which will damage the device and void the Warranty. Dont immerse the device into water and place near washbasins or any wet locations. Dont spill food or liquid on the devices. Dont attempt to dry the device with external heat sources, such as microwave or hair dryer. Dont use any corrosive solvent or water to clean the device. We recommend using dry cloth to clean the surface only. Dont use any sharp tools to probe the internal components, connectors or contacts, doing which may lead to device malfunction and void the Warranty simultaneously. Product Specications Functions Communication Interface Power & Battery Charging Key Management Encryption Algorithm Support Operating System Product Size Product Weight Operating Temperature Operating Humidity Storage Temperature Storage Humidity EMV chip card reader (ISO 7816 compliant class A, B, C card) NFC Card Reader (EMV contactless, ISO 14443A/B) Over-the-air rmware update Over-the-air key update Bluetooth 4.2 BLE Lithium polymer rechargeable battery 500mAh, 3.7V Via USB Type-C DUKPT, MK/SK TDES Android 4.2 or above, iOS (iPhone 6s or above, iPad Air 2 above, iPad Mini 5 or above, iPad Pro except 2016 version) 82.5 x 69.0 x 10.5mm (approx.) 75g (approx.) 0C 45C (32F 113F) Max 95%

-20C 55C (-4F 131F) Max 95%

Problems Device cannot be paired Device loses the connection with your smartphone or tablet when the device has gone into auto-o mode. Device does not work with your phone or tablet Device cannot read your card successfully Device has no response Recommendations Please press the power on button to restart your device. Please check to see if you can nd the devices Serial Number (Shown on the back of device) in the Scanned Device List of your smartphone or tablet. Please press the power on button to turn on the device again. The device will automatically connect with your smartphone or tablet again. The device may be at lower battery level, please use the USB cable to recharge it, then retry. Please ensure the device or smartphone/tablet is within the reception range. Please ensure the Bluetooth function of your smartphone or tablet is turned on. Please check the version of your operating system is supported for this devices operation. Please press the power on button to turn on the device again. The device will automatically connect with your smartphone or tablet again. The device may be at lower battery level, please use the USB cable to recharge it, then retry. Please ensure the device or smartphone/tablet is within the reception range. Inserting card Please check if the device has power when operating and ensure devices are connected. Please follow the application instruction to insert or tap card. Please ensure that there is no obstacle in the card slots. Please check if the chip of the card is facing the right direction when inserting card. Please ensure that your phone/ tablet is a supported model for this devices operation. Please insert card with a more constant speed. Tap Card/Mobile Wallet Please check if your card supports NFC payment. Please ensure if your card is placed within 4 cm range on top of the NFC marking. Please take out your NFC payment card from wallet or purse for payment to avoid any interference. Please use a paper clip to press the reset button at the bottom for reboot. Any damage or defects caused by a failure to follow the instructions which relate to this device or as the result of an accident, abuse, misuse, misapplication, product modication, improper voltage or current, acts of God, shipping damages or loss, or damage caused by service performed by anyone other than our company are expressly excluded from the warranty stated below. We are not under any obligation to support the device for all operating environments, including but not limited to, interoperability with all current and/ or future versions of software or hardware. Please contact the dealer for any warranty or customer support services. Any repair of the device by yourself will void the Warranty. FCC Caution Statements:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimetres between the radiator and your body. Lights COME ON in consecutive order Flashing all lights 3 times

*Power O completely after 3 hours of inactivity Power o completely when 5 minutes without any connection Long press for 4 seconds and release power button Revise v.1 / 20180509